Search Documents

By G. J. Armstrong, K. S. Lynch, C. G. Thomas, L. A. Baker, R. J. Cornelius

The presence of geothite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18-in. deep bed of green balls, the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind, and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1974

[NORTH AMERICA UNITED STATES Alabama BIRMINGHAM BURROWS, WILLIAM C. CORD, RICHARD H. COSTON, OTIS D. JR. FAIRHOPE RUFFLES, WILLIAM R. HUNTSVILLE WAGGONER, JERRY B. MOBILE PETROUTSON, PETER C. SELMA JONES, JAMES J. JR. UNIVERSITY CUDWORTH, JAMES R. JONES, WALTER B. RICHARDS, EDWARD F.]

Jan 1, 1961

By C. R. Fulton

The idea of making permanent magnets by sintering is not a new one, but until the introduction of the iron-nickel-aluminum permanent-magnet alloys there was little need for such a process. Permanent-magnet alloys in use up to the time of this development could be forged and machined to the exact size or shape required without too much difficulty. These new Fe-Ni-A1 alloys, which have become known as Alnico in this country, soon became very popular because of their superior magnetic properties, but when they were made by casting they did have some disadvantages when compared with the older type of permanent-magnet steels. Among these disadvantages were the following: 1. It was almost essential that they be cast to size, since they could not be readily forged or machined. The material could be ground but this was quite expensive, particularly for small magnets in large quantities. 2. The material had a large grain size and was mechanically weak. 3. Close tolerances could not be held and on small magnets this meant grinding almost the entire magnet. Because of the brittle nature of the material, there was considerable loss due to chipping and cracking during these grinding operations. 4. Because of its high aluminum content, the molten alloy had a high surface tension. It was difficult to prevent loss of aluminum by oxidation during the melting operation. In view of these difficulties it is not hard to understand why a process for sintering alnico was developed, or why sintered alnico has come into such widespread use in recent years. It might be well to qualify this by saying that it has come into widespread use for small magnets weighing 2 oz. and less, of the type shown on Fig. I. In this size range, sintered alnico has been able to compete in price with cast alnico. Magnets larger in size, of the type shown on Fig. 2, can be made but they do not compare favorably in price with the cast material. An idea of the range of sizes that have been produced is given by Fig. 3, which shows a small magnet weighing 0.006 oz. and a large magnet with a steel insert weighing 4 lb., both made from sintered alnico. Magnets weighing more than 2 oz., however, should not be made from sintered

Jan 1, 1945

By VILLIAN BRADEN

THIS paper is presented in the hope that it will be instructive in view of the future large expansion of the mining industry in the west-coast countries of South America. There is a more or less general impression that the Spanish-American workman is inferior to the American, but after some years of experience and observation I doubt the correctness of this view. Taking into consideration all the elements which make for efficiency of labor, it has been found, particularly in Chile, that under proper organization native labor yields as much, man for man, and more, dollar for dollar, than in the Western United States. If a manager is willing to accept unreservedly the c costumbres del pais, without combating intelligently and patiently the ones tending to inefficiency, he should expect no better results than he deserves. He must conscientiously insist that a " square deal " be given and exacted; that liquor be excluded from camp as far as possible; that comfortable quarters and other uplifting elements of life be provided; and that the costumbres del pais shall not be over-ridden roughshod. He should also insist upon the gradual and reasonable adjustment of these conditions to the exigencies of the work; and (by no means the least difficult of his tasks) he should select the most competent men to patiently direct and teach the natives in the several departments, and by their own example encourage self-respect and decency. While the Braden mine is by no means as yet operated on a large scale, according to modern rating, it will nevertheless be interesting to note what has actually been accomplished there. An illustrative description of the mines and mill of the\

Oct 1, 1909

By R. Hadfield

Since the writer has been intimately connected with the development of manganese steel for many yearsm some remarks upon the early work wutg regard to the rolling and forging of the material might be of interest…

Jan 1, 1915

By K. D. Snyder

Barite deposits occur in the Iglesiente-Sulcis district of southwestern Sardinia, an historically important lead-silver-zinc district. Barite, often genetically associated with the base metal deposits, has become an independently important economic commodity. Barite deposition in southwestern Sardinia was related to Caledonian, Hercynian, and Alpine orogenic cycles. A model is presented that relates synsedimentary, karstic, vein, and residual deposits. Synsedimentary deposits are widespread, have common depositional characteristics, and act as sources, along with hydrothermal systems, for other barite deposit types. Caledonian-, Hercynian-, and Alpine-related secondary enrichment processes resulted in residual and karstic deposits that are complex in terms of their geometry and texture, but are more economically important than those of synsedimentary or hydrothermal origin.

Jan 1, 1985

By Alden Greninger

IN a recent study1 of the deformation of metastable beta copper-zinc and beta copper-tin crystals, it was established that the parallel markings that appear on the surface of these crystals after slight deformation represent lattice transformations. Stereographic analysis showed that in beta copper-tin, the poles of these markings deviated one or two degrees from poles of the form { 133 } . In beta copper-zinc the plane delineated by the markings corresponded to no one crystallographic plane of the matrix lattice; the marking poles deviated from 5° to 11° from poles of the form {110}, and were displaced only a few degrees from (110) zones. Inasmuch as the new transition lattices produced as the result of the deformation are different for each alloy, it was thought at first that the habits of the markings might be the result of a cooperation between matrix lattice and transformed lattice. (Both matrix lattices are body-centered cubic.) Such a cooperative effect is thought to obtain in the formation of Widmanstätten figures, for it is well known that the matrix lattice alone does not determine the habit assumed by a segregate phase. On the other hand, it is not inconceivable that the dissimilarity in mark-ing habit might be due to differences in deformation characteristics of beta brass and beta bronze. Barrett and co-workers2 have shown that slip-line habits in pure iron are markedly different from those in high-silicon ferrite; and although it has been repeatedly demonstrated that plates of a segregate phase do not necessarily form on the slip planes of the matrix lattice, deformation characteristics may be more intimately allied with plate formation when a transformation is made to occur as a result of plastic deformation. However, there is the fact that the orienta-tion of markings in metastable beta copper-zinc is the same whether the markings be produced by quenching, deformation, or liquid-air cooling; likewise, quenching and deformation markings in metastable beta copper-tin are oriented in the same way with respect to the beta matrix.

Jan 1, 1938

By E. A. Moulder

The mining industry is continually faced with problems involving dewatering, pollution, water supply, leaching and hydrochemical mining and prospecting. Greater application of the principles of ground-water hydrology to solution of these problems promises improved operating efficiency, increased safety and better public relations. Estimating the magnitude of dewatering for a proposed mine may be a major factor in determining the feasibility of proceeding with mine development. Diverting the source of ground water to an abandoned mine may save costly treatment of acid-mine drainage. Development of a large ground-water supply near an ore deposit may enhance the possibilities of a leaching operation. Detection of certain dissolved minerals in water from springs or wells may lead to hitherto unknown mineral deposits. Current efforts of industry, educational institutions and government are making these kind of events more commonplace. Dewatering of Mines The magnitude of dewatering problems was dramatized by a flooding that occurred last year in a gold mine in South Africa. During drilling operations at the West Driefortein mine, a major fracture was encountered from which large volumes of water issued necessitating evacuation of 1350 men from the mine. Dewatering required an increase in pumping of more than 80 million gpd. Models of ground-water systems are being used to test alternate plans for dewatering mines. Using the models in conjunction with computer optimization programs may lead to minimizing costs of operation. In addition to computer simulation of aquifers associated with phosphate deposits in North Carolina mentioned in last year's report, two USGS employees developed a model to estimate the amount of pumping required to dewater a mine site in Colorado.

Jan 1, 1970

By James P. Kimball

In a paper which I had the honor to present to the Institute at the Montreal meeting, September 1879,I took occasion to refer incidentally to certain practical difficulties in the sampling of coal-seams {Trans. Vol. VIII., p. 181-3). This reference was particularly to the unequal distribution of sulphur in the form of pyrite, and to the necessity of discriminating between the several members or " benches " of a coal seam as to their relative proportion of visible sulphur. What is a practically truthful estimation of the sulphur of a coal seam, is not necessarily the estimation of an average of sulphur in any given line of cross-section of the seam. Cornparatively speaking, the range of sulphur in quantity is generally so low that errors in its determination, arising from neglectful sampling or from slips in the laboratory, fall chiefly upon this single ingredient. Not so,

Jan 1, 1884

By D. J. McAdam

In a recent survey of the literature, the author has found evidence incompatible with prevalent views regarding the technical cohesive strength and yield strength of metals. Some of the evidence regarding the technical cohesive strength was presented in a previous paper,21 and views were presented that are believed to be in better accord with the evidence. In that paper, it was shown that the technical cohesion limit (contrary to prevalent views) varies with the combination of principal stresses,t and that the influence of plastic deformation on the technical cohesive strength is not in accordance with prevalent views. In this paper, consideration will be given to both the technical cohesion limit and the yield stress as affected by the combination of principal stresses. Evidence will be presented that the variations of the yield stress and the technical cohesion limit with the combination of principal stresses are not in accordance with prevalent views. Consideration will also be given to ductility and work-hardening capacity, which depend on the initial difference between the technical cohesion limit and the yield stress. By the "technical cohesion limit" is meant the mean stress at actual or poten- tial* fracture. An example of a rechnlcal cohesion limit is the "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. The cohesion limit thus obtained for a ductile metal, however, has been greatly altered by the plastic deformation. It is important to consider the cohesion limit of the metal prior to this deformation, and the variation of the cohesive strength with plastic deformation. The relation between the cohesion limit and the corresponding flow stresst determines the ductility of a metal and the energy that it will absorb before fracture. In this paper, as in the previous paper,21 tensile stresses will be viewed as positive and compressive stresses as negative. The algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated Sz In the previous paper, attention was confined to stress combinations with two of the principal stresses equal (with the intermediate principal stress S2 equal eithel to S3 or 31). In this paper, consideration will also be given to the effect of stress combinations with all three principal stresses unequal. In the earlier sections of the paper (pp. 3I I to 324), attention will be confined to stress combinations with

Jan 1, 1942

By D. J. McAdam

In a recent survey of the literature, the author has found evidence incompatible with prevalent views regarding the technical cohesive strength and yield strength of metals. Some of the evidence regarding the technical cohesive strength was presented in a previous paper,21 and views were presented that are believed to be in better accord with the evidence. In that paper, it was shown that the technical cohesion limit (contrary to prevalent views) varies with the combination of principal stresses,t and that the influence of plastic deformation on the technical cohesive strength is not in accordance with prevalent views. In this paper, consideration will be given to both the technical cohesion limit and the yield stress as affected by the combination of principal stresses. Evidence will be presented that the variations of the yield stress and the technical cohesion limit with the combination of principal stresses are not in accordance with prevalent views. Consideration will also be given to ductility and work-hardening capacity, which depend on the initial difference between the technical cohesion limit and the yield stress. By the "technical cohesion limit" is meant the mean stress at actual or poten- tial* fracture. An example of a rechnlcal cohesion limit is the "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. The cohesion limit thus obtained for a ductile metal, however, has been greatly altered by the plastic deformation. It is important to consider the cohesion limit of the metal prior to this deformation, and the variation of the cohesive strength with plastic deformation. The relation between the cohesion limit and the corresponding flow stresst determines the ductility of a metal and the energy that it will absorb before fracture. In this paper, as in the previous paper,21 tensile stresses will be viewed as positive and compressive stresses as negative. The algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated Sz In the previous paper, attention was confined to stress combinations with two of the principal stresses equal (with the intermediate principal stress S2 equal eithel to S3 or 31). In this paper, consideration will also be given to the effect of stress combinations with all three principal stresses unequal. In the earlier sections of the paper (pp. 3I I to 324), attention will be confined to stress combinations with

Jan 1, 1942

By M. D. Flavel

The paper describes the physical aspects of the compression and impact crusher types along with the information needed to apply, install and operate them to best achieve designed performance levels. It reviews key performance parameters such as energy size relationships for crushing processes and how automation devices can optimize machine productivity. Weaknesses of existing application engineering methods are discussed. The use of pilot plant information and appropriate laboratory testing procedures are reviewed from the point of view of the application design engineer so that the best type of machine can be selected for a proposed installation.

Jan 1, 1982

By E. R. Parker, E. A. Smith

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By E. A. Smith, E. R. Parker

Metallurgists and engineers have always been interested in the mechanism of high-speed deformation because metals are rapidly deformed in various applica-tions and manufacturing processes. The deformation of metals by impact loads has recently engaged the attention of a number of investigators. Many of their results have not been disclosed but some of the published investigations1-8 have shown that the tensile strength, yield strength and elongation generally increase with increasing strain rate. The investigation reported herein is an attempt to determine the reason for this increase in strength and elongation. found to depend upon the strain rate. In the bars broken at high speeds, the slip bands appear to be more numerous. This might account for the higher strength as well as the greater elongation. Experimental Procedure Single crystals of copper (approximately 99.98 per cent) were made in graphite molds by the conventional method of lowering the mold out of the hot zone of a hydrogen furnace at a rate of one inch per hour. Solidification progressed from the bottom upward, forming a single crystal. The crystals were about 0.30 in. in diameter and 4 in. long. They were

Jan 1, 1944

By G. P. Boomsliter

IN previous discussions on stresses in hoisting ropes, little has "been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses. for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured.

Jan 2, 1927

By R. M. Waterstrat

The phases occurring in the V-Mn system were studied by means of X-yay diffraction and metallo-paphic techniques, using are-melted alloy specimens annealed in the temperature range 800° to 1150°C and quenched. The bcc solid solution extends at 1250°C all the way from vanadium to 6-manganese. Below 1050°C the a-phase is formed, and the terminal a-manganese phase is stabilized up to about 900°C by vanadium in solid solution. IN the only previous general survey of the V-Mn system Cornelius, Bungardt and Schiedtl reported the existence of three intermediate phases corresponding to the approximate compositions VMn,, VMn, and V5Mn. The phase VMn8 has recently been identified as a o phase2 but the alloy VMn was found to have a bcc structure2 corresponding apparently to the vanadium solid solution rather than to the large cubic unit cell reported by Cornelius et al. 1 Subsequent work by Rostoker and Yamamoto3 has shown that the vanadium-base bcc solid solution extends to at least 15 pct Mn at 900°C. An alloy corresponding to the composition VMn, was examined by Elliott,4 who reported that the as-cast sample as well as samples annealed at 1200o and 1300°C had bcc structures, but that annealing at 1000°, 800") and 600°C produced two phases. One of these phases was apparently the bcc solid solution and the other resembled the o phase structure. Hellawell and Hume-Rothery5 established the phase relationships in manganese-rich alloys above 1000°C, and showed that the o phase in this system is replaced by the 6 Mn (bcc) solid solution at temperatures above 1050°C. These results suggest that a continuous bcc solid solution may exist above 1050°C between vanadium and 6 Mn. The present investigation was undertaken in order to develop more complete information in regard to this system. EXPERIMENTAL METHODS The alloys used in the present work were prepared by arc-melting electrolytic manganese having a minimum purity of 99.9 pct and vanadium lumps with a purity of 99.7 pct. The major impurities present in these metals were carbon, nitrogen, and oxygen and this would account for the small percentage of nonmetallic inclusions observed metal-lographically. The arc-melting was at first performed under a helium atmosphere and it was necessary to keep the melting times as short as possible in order to minimize the loss of manganese by vaporization. It was later found that the evaporation of manganese was considerably reduced when the melting was done under argon atmosphere. The final composition of each alloy was calculated by assuming that the total weight loss during melting was due to evaporation of manganese. Compositions which were calculated in this manner agreed reasonably well with the results of chemical analysis, as shown in Table I. Spectrographic analysis revealed the presence of contamination by tungsten, but in no case was the percentage of tungsten greater then 0.4 at. pct. The specimens were in each case broken in half and the fractured section was examined visually and microscopically for evidence of inhomogeneity. Each specimen was homogenized at temperatures near l100°C, as shown in Table I. After this treatment most specimens consisted of large columnar grains of the bcc vanadium solid solution. The etchant used in most of the metallographic work consisted of 20 pct nitric acid, 20 pct hydro-flouric acid, and 60 pct glycerine. It was found that this etchant would clearly delineate the phases present in these alloys although it does not produce any striking contrast between the phases. For certain manganese-rich alloys, a 1 pct aqueous solution of nitric acid was used. This etchant gave a brown color to the a-manganese phase, whereas the o phase was virtually unattacked and appeared very light as shown in Fig. 1. The etchants used by Cornelius et a1.l were found to produce spurious effects in some of these alloys. In particular, the vanadium-rich alloys etched in hot sulfuric acid often appeared to consist of two phases when both X-ray diffraction and etching with the glycerine-acid mixture indicated the presence of single phase bcc solid solution. A few percent of what appears to be an oxide or nitride phase was found at the grain boundaries and in the interior of the grains, especially in the vanadium-rich alloys. All alloys were annealed in sealed silica tubes containing 1 atm of pure argon and these tubes were then quenched in cold water. Although some manganese loss occurred during annealing, the loss seemed to be confined to the surface of the speci-

Jan 1, 1962

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By Paul D. Merica, W. A. Mudge

ONE of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion The corrosion resistance of metals and alloys is never absolute and all-inclusive, a particular alloy will withstand some corrosive conditions well and fall utterly under others Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications One wants a soft, ductile sheet metal resistant to atmospheric corrosion, another, a high-strength alloy resistant to sulfuric acid The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-Resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less. than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance

Jan 1, 1935