Search Documents

Chairman James F. Kemp :—I call upon Prof. Albert Sau-veur to open the general discussion on the subject of sound steel ingots. Albert Sauveur, Cambridge, Mass.:—I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain Rome very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my views. I have always remembered my astonishment, not to say dismay, some twenty years ago, when I beheld for the first time a steel ingot, a rail steel ingot, that had been split open from top to bottom. There was the pipe! There was an enormous cavity extending from a short distance from the top to nearly one-third of the length of the ingot; and when I was told that manufacturers seldom discarded more than one-tenth of the total length of the ingot it became evident to me that a large proportion of piped, and therefore, defective, or at least weak and dangerous, rails were manufactured; in fact, probably one rail out of six, nearly 17 per cent., of dangerous rails.

Jan 1, 1914

By E. N. Mazza, H. S. Kalish

The effect of sintering types 302, 3028, and 430 stainless steel powder compacts in hydrogen and dissociated ammonia was investigated. It was found that sintering in dissociated ammonia resulted in as much as 0.5 wt pct increase in the nitrogen content of stainless steel even though the dissociation of the gas was complete. Sintering in hydrogen, on the other hand, reduced the nitrogen content of the stainless steel to less than 0.01 wt pct. In the case of the 302-type stainless steel, the low nitrogen content resulted in a material that was largely ferritic, whereas the high nitrogen content rendered the material fully austenitic. Sintering in dissociated ammonia resulted in lower density, generally lower tensile strength, less ductility, and higher hardness than sintering under equivalent conditions in hydrogen. The reduction of oxides on both stainless steel and iron particles was found to be effected by hydrogen partial pressure in the sintering atmosphere. Compacting pressure was found also to effect oxide reduction during sintering. DISSOCIATED ammonia often is used as a substitute'.' for hydrogen in sintering and in annealing, since economic advantages sometimes can be obtained by such a substitution. In addition, anhydrous ammonia contains very little impurity. Thus, dissociated ammonia gas is very dry whereas tank hydrogen often must be freed of oxygen and water vapor prior to use in many applications. The sintering of stainless steel powder compacts as well as bright annealing is well recognized as requiring a hydrogen atmosphere and for the foregoing reasons dissociated ammonia is frequently substituted. It has generally been overlooked, however, that the nitrogen in dissociated ammonia might have an important effect on the sintering process and on the properties of stainless steel compacts. Considered an inert gas in many applications, nitrogen, on the other hand, is very reactive with cer- tain metals. Dissociated ammonia could not be used for hydriding zirconium or titanium. Nitrogen reacts with columbium, tantalum, chromium, uranium, thorium, and many other active metals. Iron and iron-base alloys are, for the most part, inert in nitrogen but there are many borderline cases. It has been reported that stainless steel stabilized with columbium or titanium should not be sintered in dissociated ammonia.3 olybdenum has been reported as reacting with dissociated ammonia to a minor extent.' Although most of the reactions with iron-base alloys are attributed to the action of un-dissociated ammonia and the action of nascent nitrogen, Uhlig4 showed how readily pure molecular nitrogen reacts with and diffuses into 18-8 stainless steel at 1150°C. He also pointed out how readily nitrogen diffuses out of 18-8 stainless steel when heated in pure dry hydrogen, and these thorough investigations on the subject show that commercial stainless steels are nitrogen-bearing, since they are melted in air. The effects of nitrogen in stainless steel, particularly the 18-8 Cr-Ni type, previously have received considerable attention." In 1926, it was pointed out

Jan 1, 1956

By Edward Steidle

Those who have followed the rapid progress in rock-dusting bituminous-coal mines must admit that opinion crystallized during the year just closed in support of this preventive of coal-dust explosions. Up to 1924 only one mining company in America practiced rock-dusting on a large scale, but during 1924 forty-two companies had adopted this safety measure, and the "boom" is expected to extend over the next two or three years. Alabama is represented by 1 company, Colorado by 3, Illinois by 4, Kentucky by 1, New Mexico by 4, Pennsylvania by 20, Utah by 8, and Wyoming by 1. A total of about 500 miles of entry has been dusted. Illinois leads with 275 miles of dusted entries and Pennsylvania holds second place with about 175 miles. In each case there is a sense of great security, not only on the part of the operator but by the miner as well. It is also interesting to note that during 1924 the compensation rating or inspection bureaus in twelve of our coal-producing states revised their rating schedules so that a credit would be given for rock-dusting. This credit ranges from 10 to 20 cents per $100 payroll. Recent drastic federal and state regulations approved by mine operators made rock-dusting compulsory in bituminous coal mines in Utah, beginning July 1, 1924. Legislative action favorable to rock-dusting may be expected in other states. Colorado has already proposed a change in its laws, and Pennsylvania, Maryland, Washington, and West Virginia are giving the matter consideration. If the rock-dusting problem is handled properly and proves to be entirely successful, no mining man of any standing will delay applying it in his mine. State legislation regarding this matter may or may not solve the problem. At present, the mining companies that are rock-dusting of their own choice are doing it carefully and thoroughly. In Utah, some are doing it conscientiously, trying to get what benefits can be obtained while others are reported to be doing it only to keep within state regulations. In any event, if we are to have new legislation, it is essential that the various states know what they are about and then, if possible, work for uniform regulations.

Jan 1, 1925

By George A. Komadina

The Pima mine lies 20 miles southwest of Tucson, Ariz., and 45 miles north of the Mexican border. It is located on a hillside overlooking Tucson, which allows for gravity flow generally through the plant. In April 1965, an expansion was authorized by the mine's board of directors. This will triple the mine's output to 18,000 tpd. At this rate, it is estimated that there is sufficient ore to last 20 years.

Jan 6, 1965

By E. S. Bumps, H. D. Kessler, M. Hansen

The titanium-rich end of the Ti-AI phase diagram has been determined to the compound TiAI3 (62.7 pct Al), thus joining the aluminum-rich portion previously investigated by others and completing the diagram. Micrographic analysis and X-ray diffraction were the chief methods used to determine the phase relationships. THE Ti-Al phase diagram has been investigated as part of a program on titanium phase diagrams for the Wright Air Development Center. Included in the available information concerning the phase relationships in titanium-rich Ti-A1 alloys is a brief statement by Brown' that: "aluminum raises the transformation temperature to 1000°C (183Z°F)." This observation is interesting in that it is the first example of a metallic alloying component raising the transformation temperature of titanium, and consequently widening the field of the a solid solution. Busch and Freyer' presented resistivity data which indicated the formation of titanium-rich solid solutions of 1 and 3 pct A1 alloys prepared by powder metallurgy methods. Duweza found that there is only one other intermediate phase other than the known compound TiA1, (62.7 pct Al). This phase, designated as y, is of variable composition; its crystal structure is of the AuCu type and is therefore based on the composition TiAl (36.02 pct Al). Earlier work on the constitution of the aluminum-rich alloys has been reviewed by Hansen, and need not be discussed here. The tetragonal crystal lattice of TiAl,, as found by Fink, Van Horn, and Budge," was confirmed by Brauer." Recently, Schubert7 has reported that TiA1, is homogeneous within a limited composition range; however, the solubility limits were not given. The Ti-A1 phase diagram as presented in. this paper was determined by micrographic analysis of alloys containing from 1 to 62 pct Al, annealed at and quenched from temperatures between 700" and 1400°C. The phases and phase ranges investigated extend to the compound TiA1, (62.7 pct Al) to join the aluminum-rich end of the system determined by other investigators, thus completing the diagram. Methods of Investigation Preparation of Alloys: Iodide titanium, 99.9+ pct pure, obtained from the New Jersey Zinc Co., and high-purity (99.99+ pct) aluminum sheet from the Aluminum Co. of America were used to make up alloy ingots weighing 10 to 20 g. Detailed descriptions of melting techniques have been presented previously for work on the Ti-Mo and Ti-Cb> nd Ti-Si" phase diagrams. Briefly, the melting practice consisted of arc melting an accurately weighed charge in a copper block crucible insert in a non-consumable tungsten electrode furnace, under helium at atmospheric pressure. All ingots were carefully weighed after melting to detect possible losses. Comparison of weight before and after melting showed no appreciable weight changes. Also, chemical analyses were in close agreement with nominal compositions, Table I. The diagram as presented is, therefore, based on nominal compositions. Alloys were prepared having the following nominal aluminum contents: 1 ... 36 (1 pct increments), 38, 40, 41, 42.5, 44, 45, 46, 47.5, 49 . . . 64 (1 pct increments), 67, 70, 80, and 90. Ingots with up to 14 pct A1 were cold-pressed various amounts in order to increase the rate of attaining equilibrium structures on heat treatment. The amount of cold deformation that could be applied decreased with increasing aluminum content, until alloys containing 12 pct A1 or more cracked after only a few percent deformation. Annealing Treatments: Samples annealed at temperatures of 700" to 1000°C were sealed in

Jan 1, 1953

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE mechanism by which the super-saturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications. 1,2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon {111} matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;3 at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate y but that of a transition lattice ?'. Since this is also platelike in shape and also lies upon the {111} matrix planes with the {110} direction in the matrix parallel to the {11.0} direction in ?', it seems likely that the original platelet particles are merely ?' in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the {00.0} plane in ?' are identical with those on the {111} matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures ?' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, ? ' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system,2,4 hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructure, Brinell hardness and electrical resistivity of the three alloys. PREPARATION OF SAMPLES AND EXPERIMENTAL PROCEDURE The preparation of the 20.2 per cent Ag alloy has been described.2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent Al and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By R. S. Wagner, H. Brown

Criteria for nucleation with the aid of twin planes during crystal growth from the melt are discussed. It is shown experimentally that bismuth crystals can grow from a subercooled melt in a twinned bismdtic form. A mechanism of growth based on the presence of at least me twin plane is proposed. It is well known that faceted growth can be observed in crystals grown from the vapor phase, dilute solutions, or from the melt. Faceted growth, in which the crystal is bounded by its slowest growing faces, will occur if the growth rate is strongly orientation dependent. The addition of atom layers on a facet plane can only occur by two-dimensional surface nucleation or with the aid of an imperfection. Nucleation with the aid of dislocations was proposed by rank' and observed to be of particular importance in crystal growth from the vapor phase. Nucleation with the aid of two-dimensional imperfections, notably twin planes, was suggested by stranski2,3 and Frank.4 A twin plane, terminating at the growth interface, can form a reentrant step at which nucleation can occur at a much smaller super-saturation (or supercooling) than required for two-dimensional surface nucleation. Nucleation by a twin plane usually results in a fast growth rate along a crystallographic direction parallel to the twin plane. Such a nucleation mechanism, based on the presence of a twin plane, has been used by Dawson5 to explain the growth and morphology of sheet-like crystals of paraffin n-hectane. In recent years more evidence was found that nucleation by twin planes occurs frequently in crystal growth from the vapor phase and from dilute solutions, for example, in cadmium,' barium titanate,7 silver,8 silicon9 and gallium arsenide.10 In crystal growth from a supercooled melt, however, nucleation by twin planes has so far only been observed in materials with the diamond or zinc blende structure. Bennett and Longini11 were the first to recognize the important role a single twin plane plays in the growth of germanium dendrites. Subsequently, it was found that a prerequisite for continued propagation of germanium dendrites is the presence of two parallel twin planes which form a self-perpetuating system of nucleation sites.12 Sili- con and some III-V compounds such as InSb also grow dendritically by twin plane nucleation. It appears that the following criteria must be satisfied in order that nucleation with the aid of twin planes can occur: A) The growth form of the material must be faceted." B) The formation of twin boundaries, by a fault in layer sequence during growth, by plastic deformation, or by an accidental meeting of properly oriented crystals, must be possible. C) Twinning must form a reentrant step where the twin boundary terminates at the faceted growth interface. D) These three conditions are necessary, but in certain cases not sufficient for continued crystal growth with the aid of a twin plane. Depending on interface morphology, a combination of more twin planes is sometimes required to form a self-perpetuating system of nucleation sites. This investigation was carried out with the idea in mind that nucleation with the aid of twin planes is a more general phenomenon and should occur in those materials, grown from a supercooled melt, which satisfy the criteria outlined above. It has been found that crystals of high-purity bismuth grown from a supercooled melt can grow by the aid of a twin plane. In the first two sections the faceted growth form and the twinning elements of bismuth are discussed. In the last section prismatic crystals of bismuth, which appear to grow with the aid of a deformation twin are discussed.

Jan 1, 1962

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By R. L. Hadley, G. Derge

The amounts of oxygen in liquid iron-titanium alloys up to 50 pct Ti were measured and the oxide phases in equilibrium with these alloys were determined by using TiO² crucibles. A minimum of about 0.003 pct 0 occurs at less than 1 pct Ti. The various liquid and solid oxide phases can be arranged on a ternary isotherm. THREE characteristics of titanium contribute to the interesting aspects of its reaction with oxygen in liquid iron: 1—It forms a number of stable oxides. 2—All oxides have large negative free energies of formation. 3—The pure metal exhibits high solubility for oxygen. In addition, the use of titanium as a stabilizing and strengthening element in alloys suggests a need for investigation of its reactions in amounts greater than those normally required for deoxidation. These higher compositions are also of interest because they occur during the addition of ferroalloys and produce deoxidation products before dilution is achieved. Titanium Deoxidation in the Literature While the use of titanium as an alloying element and deoxidizer has been common for several decades, the first detailed study of its deoxidizing characteristics was carried out by Wentrup and Hieber' in 1939. These authors determined the extent of deoxidation possible with titanium and identified, by microscopic examination, the products formed. They found that titanium in excess of 0.2 pct did not reduce the oxygen content of iron below 0.004 pct at 1600°C. They identified the spinel FeO-TiO² at low titanium concentrations and Ti2O³ in melts containing more than 0.2 pct Ti. A portion of the area surveyed by Wentrup and Hieber has been investigated recently by Evans and Sloman² using X-ray diffraction for inclusion identification. They concurred in general with the findings of Wentrup and Hieber, but reported the existence of Ti³O5 as a deoxidation product in the range near 0.1 pct Ti. Comstock, Urban, and Cohen³ discussed the deoxidation of iron with titanium, correlating the data of Wentrup and Hieber with free-energy data for the titanium oxides. Scatter at high titanium values was considered attributable either to the formation of an oxide exhibiting high solubility in liquid iron or to the entrainment of solid oxide particles leading to high apparent solubility. Chipman' has calculated the deoxidation curves for titanium based on free-energy data for titanium oxides. These calculations (Fig. 1) and those of Comstock, Urban, and Cohen involve assumptions as to the activity coefficients of oxygen and titanium in liquid iron, since such data have not been determined. Investigation of the deoxidizing characteristics of chromium" and vanadium0 have shown that these elements decrease the activity coefficient of oxygen in liquid iron, leading to a tendency toward relatively high oxygen values and experimental scatter in highly alloyed melts. Experimental This investigation involved two major objectives: 1—determination of the composition of the oxide phases in equilibrium with liquid Fe-Ti alloys, and 2—establishing the pattern of oxygen solubility in liquid Fe-Ti alloys at titanium concentrations in excess of that required for attainment of minimum oxygen content. Raw Materials Ingot iron was used having the following composition: 0.02 pct C, 0.017 pct Mn, 0.01 pct Si, 0.02 pct S, 0.006 pct P, and 0.03 pct 0. The titanium used

Jan 1, 1956

By J. J. Gilman

WHEN a cleavage crack that is moving through a crystal intersects a screw dislocation, a jog is created in the crack front. As the crack continues to move, the jog leaves behind a cleavage step. This mechanism was proposed by Amelinckx and Votava,' Pratt, bnd Gilmanh t about the same time. At that time the evidence for the mechanism was largely indirect. Other evidence has been presented by Low, Bilby and Smith,5 and Forty.' It is the purpose of this paper to present more direct evidence of this mechanism and to show that observations of cleavage steps can be used to detect screw dislocations. Experimental Lithium-fluoride crystals that were purchased from the Harshaw Chemical Company, as well as natural mineral crystals and metal crystals, were used in the experiments. Although cleavage steps can be observed on transparent crystals with a metallurgical microscope, the contrast is poor. Marked improvement in the contrast is obtained by depositing thin (1000A) films of silver or aluminum onto the surfaces. The contrast also can be improved by using a phase-contrast microscope, but the simpler silvering method gives just as good results. Tolansky interferometric microscopy, and electron microscopy were used to measure the heights of cleavage steps. The etching techniques developed by Gilman and Johnstonh ere used to detect dislocations in the LiF crystals. Results The dislocations that create cleavage steps can originate in three ways: a) They can be grown into crystals b) They can be introduced by plastic deformation prior to cleavage c) They can be formed just in front of the tip of a propagating cleavage crack.' These three situations will be considered in turn. Grown-in Dislocations—It is not possible to see the individual monomolecular cleavage steps that emanate from isolated screw dislocations in crystals.

Jan 1, 1959

By J. J. Mike

During the past few years the combination of continuous billet casting with in-line reduction has been studied and several machines have been built with this capability included in the design parameters. (1,2,3,4,5) In-line reduction and continuous casting in combination are obvious and attractive. As pinch rolls are already in place for the continuous casting operation, it can be readily seen that a redesign of the mechanical and electrical equipment of the pinch rolls is all that is necessary to have in-line rolling. There have been numerous in-line reduction experiments conducted by simply increasing the pinch roll pressure on existing machines. (6,7,8,9) These generally failed to produce quality billets and often resulted in internal metallurgical defects (Figure 1).

Jan 1, 1972

By P. A. Albert

THE to a transformation has been investigated by Newkirk1 in sponge titanium alloys which had been relatively slow-cooled so that several grains formed in a former grain. For a nucleated from , Newkirk assumed the following relationships and found them consistent with his experimental results: (00.1)a (110)Pll.01. II [111] Liu and Margolin,' in their investigation, found that the habit planes of martensitic in titanium consisted of planes of the families (3341, and (3441,. Using Newkirk's orientation relationship, the (3341 habit plane is found to correspond to the (1450) plane of a.

Jan 1, 1954

By Aloys H. Wohlrab

[THE conditions that govern the selection of a suitable type of detachable bit for the small isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may of be able to adopt the practice of larger mines because of necessary capital expendites for equipment for detachable-bit sharpening and shanking. The perfect detachable bit, suitable for all conditions, has n yet been developed. CONVENTIONAL DRILL BIT IN USE That drilling speed increases as the hit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests married out by Holman Brothers Limited1 with 7/8-in. show that when bit sizes are reduced from. 1 ½ in. 1 3/8 in., and 1 3/16 in., to 1 3/8 in., 1¼ in., and it' in., respectively, the volume of the hole is15 per cent less and the drilling speed 4q per cent higher. Recent tests by the United States Bureau of Mines2,3in hard, uniform basalt showed that a reduction in average gauge from 2.077 to 1.826 in., a difference of 0.251 in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr characteristics) by some mines.4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and I4° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as can be forged economically. Shop practices and costs have been discussed in earlier papers.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert.7 REQUIREMENTS FOR DETACHABLE BIT FOR HOLLINGER Under these circumstances, it was apparent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in]

Jan 1, 1942

By James M. Link

The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple compared to the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve the understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instances, more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test loops such as the one at the Colorado School of Mines Research Institute. The pilot scale projects are designed to provide the basic engineering data necessary to design slurry transport pipeline systems. Usually three slurry solid concentrations are pumped at various line velocities and optimum slurry densities and velocities are determined. Critical velocities, friction head losses, power requirements, and so forth, are also determined from measurements and calculations. Wear tests are also strongly recommended and anticipated pipe wear rates in inches per million tons of solids reported.

Jan 11, 1972

By C. H. Mathewson

ABOUT fifty pages of Henry M. Howe's profound treatise, "The Metallography of Steel and Cast Iron," are devoted to twinning with special reference to the origin, nature and general significance of the Neumann bands in ferrite. Howe believed with Osmond and Cartaud1 that the Neumanns are mechanical twins and his careful observations leave no doubt that these straight-sided narrow bands habitually occur parallel to trapezohedral planes of form {211}. Attempt's to develop the structure of the bands by various methods so that their identity could be established beyond question have not been conspicuously successful. Howe thought that they deflected slip bands. Some of the etching figures which have been developed within and adjacent to Neumann bands support the contention that they are twins. A good example of this effect in ferrite containing 0.6 per cent. of nickel and 1.3 per cent. of phosphorus, originally due to Harnecker and Rassow,2 was reproduced in. the 1928 lecture before the Institute of Metals Division on twinning in metals.3 In this case, the sides of the figures might represent the traces of cubic planes laid bare by etching a properly oriented grain of ferrite, twinned along a plane of form {211}. Our own observations in this direction may be represented by Fig. 1 which shows in a deeply etched cavity in the boundary region between a Neumann band and the original crystal two small crystal surfaces which resemble the faces meeting at a reentrant angle in the simple cube twinned along a bisecting plane of form {211} as sketched in Fig. 2.

Jan 1, 1928

By Harry K. Ihrig

THE hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1/8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was, necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes Co. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.11 The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 DESCRIPTION OF TEST METHOD The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1945

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By C. Schlumberger

IN the course of the past few years the authors and their associates have had different opportunities to study the electrical phenomena which accompany the oxidation of pipe lines. The causes of such phenomena are very similar to those which have been described under the name "spontaneous polarization" with reference to metallic orebodies,1 and can be investigated in the same manner. These investigations, however, until recently were of a scientific and theoretical character, and had not found any important practical application. During the year 1931, however, the authors treated several industrial corrosion problems for public utility companies. These problems usually had to be studied in towns or in densely populated areas, where it was well-nigh impossible, or very expensive, to dig pits and trenches in order to make electrical measurements on the pipe itself. The authors were thus led to evolve a method and apparatus permitting the study, from the surface, of the direction of the currents flowing from pipe lines. The purpose of the present paper is to discuss the results obtained in the course of these investigations. However, in consideration of the importance and interest of the work carried out by other scientists along the same lines, a separate chapter will be devoted to a summary of the results achieved up to the present time in the study of pipe line corrosion.

Jan 1, 1932

By C. H. Johnson

THE year 1952 has seen the continuance of the trend pointed out by Tell Ertl in this magazine a year ago, toward mechanization in metal and mineral mines. Outstanding progress has been made in the adoption of rock bolting in situations where, a short time ago it would have seemed inapplicable. New devices, better equipment, and improved practices are in part responsible for shifting fashions in mine development, stoping methods, and transportation systems. Only new mines, of course, can take the advantage of the new ideas that are being tested and demonstrated throughout the industry, but the old mines often show a surprising adaptability

Jan 2, 1953

By S. C. Sun, John A. L. Campbell

The surface properties exhibited by bituminous coal and bituminous coal lithotypes were ascertained by using streaming potential techniques. The electro kinetic prop-erties wereascertainederties of bituminous coal were found to be similar to those of anthracite. The principle electrokinetic properties of the coal and lithotypes, zero-points-of-charge (ZPC), and potential determining ions, were established. The effects of indifferent electrolytes, hydronium and hydroxyl ion sources, and polyvalent ions (cationic and anionic) were also evaluated. Location of the ZPC's with respect to pH is discussed in terms of chemical and mineralogical composition of the respective surfaces. To account for the observed electrokinetic phenomena, a generalized surface model and adsorption mechanism are proposed. Surface-dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or improve a surface-dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and floccula-tion tion. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established.' These data will be presented at a later date. Experimental Procedures The coal samples used in this research and their designations are listed in Table 1. The classical description of humic coal lithotypes as developed by Stopes" was used for the delineation of the lithotype samples. The samples were taken from the working face of a producing deep mine of the Pittsburgh seam in the area of Ellsworth, Pa. To avoid oxidation, only freshly exposed areas were sampled. The normal precautions against contamination were also exercised. Two types of samples were taken, specimens rich in a particular lithotype and a representative channel sample. The latter sample was prepared for analyses by grinding it to —35 mesh. It was screened repeatedly during the grinding to provide the largest amount of 35 x 48-mesh (standard Tyler sieves) material possible. The screened fraction was passed over a magnet and then washed several times with distilled water and finally with conductivity water. The resulting sample now termed "whole coal" was stored under conductivity water in a glass bottle. Pure lithotypes were obtained from the lithotype concentrates by hand picking, and were processed in the same manner as the representative sample. Maceral analyses, employing standard petrographic procedures," were performed on the lithotype samples to determine the purity of the samples. The results are presented in Table 2. Reflectance measurements of the vitrinites and fusinites are also reported in this table. Proximate and ultimate analyses of the samples are given in Tables 3 and 4. The electrokinetic properties of the coal samples were determined by streaming potential methods.'-' All of the chemicals used in the investigation were reagent grade (Baker analyzed). The conductivity water was prepared by doubly distilling the water in a pyrex Yoe-type still and passing the distillate through a mixed bed ion exchange column. Results In general, the electrokinetic properties of the investigated bituminous coal were found to be similar to the results of a previous study of anthracite by Camp-bell bell5 and are in accord with the suppositions of Brown." The zeta potentials of the coal and all the lithotypes were found to be negative in conductivity water. Jowett? in a study of slime coatings on coal also found bituminous coal to exhibit a negative surface. Fig. 1 shows that the negative charges, at neutral pH's, for both fusain and the gangue are very small, almost zero, while at the same pH, vitrain has the largest negative charge, almost 30 mv. Durain has a negative charge of 17.5 mv. The determination of the affect of pH on the charge of the coal surfaces revealed that hydronium and hydroxyl ions apparently behave as potential determining ions; however, they do not appear to be potential determining for the gangue. These results are illustrated in Fig. 1. As the pH of the solution was decreased, hydronium ions were adsorbed, causing the surface of the coal to reverse polarity and become

Jan 1, 1971