Search Documents

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij'usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith's determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej'ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of' damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.'2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By Manuel Eissler

The material presented in this paper is an abstract of a thesis submitted by the writer to the faculty of the Massachusetts Institute of Technology, as part requirement for the degree of Master of Science. The investigation was undertaken at the suggestion of Prof. H. 0. Hofman, and it was conducted, under his direction, in the laboratories of the Mining Department of the Institute. The purpose of the work was, first, to study some of the reactions that have been considered as a part of the mechanism of the chloridiz-ing roast, and second, to study the conditions under which nickel oxide and copper oxide may be chloridized. While the production of chlorine gas by various reactions during the chloridizing roast may not be primarily useful in the chloridation of metal oxides and compounds, it nevertheless serves a useful purpose in preventing the dissociation and decomposition of chlorides once they have been formed; for example, the dissociation of cupric chloride into cuprous chloride and chlorine. Therefore it was thought that a study of some chlorine-producing reactions would prove of interest, and the first series of experiments dealt with this phase of the subject. he object of the latter part of the work was to show the possibility of treating heavy sulphide ores, such as those of Sudbury, Ontario, containing much iron and small amounts of copper and nickel, by chloridizing and removing the copper, leaving an iron-nickel oxide product suitable for smelting in the blast furnace for nickel-bearing pig iron. The chloridizing of the copper would, of course, be preceded by a roast for the removal of sulphur, the sulphur oxides being available for the manufacture of sulphuric acid, if under the local conditions this product would be of commercial value. Reactions of the Chloridizing Roast Reaction of Sodium Chloride, Sulphur Trioxide, and Oxygen.—The first reaction studied was that involving the production of chlorine

Jan 1, 1915

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938

By Leonard C. Grimshaw

Diffusion of carbon from gases into iron has been the object of much research, because of its long recognized importance in carburizing processes, but the direct diffusion of carbon from steel into iron has received relatively little attention. Because of the increasing use of clad metals in industry, direct diffusion from steel into iron is becoming of practical importance. Therefore, the object of this investigation was to study the diffusion of carbon from several different kinds of steel directly into relatively pure iron, realizing that elements in the steels other than carbon might influence the rate of carbon diffusion. The previous work on diffusion of carbon into iron has been considerable, and includes many reports in foreign languages. This work has recently been well reviewed by Mehll and Krynitsky12 and the reader is referred to their excellent bibliographies. Methods of Study There are two main methods by which the direct diffusion of carbon from steel into iron may be studied. In one method, steel is first decar-burized in part, and diffusion of carbon then allowed to take place from the steel into the decarburized steel. This method is open to two serious objections: (1) the decarburized steel is not iron, but contains elements such as manganese, silicon, chromium or tungsten, which may be an essential part of the steel under study, and which may seriously influence the diffusion of carbon into the decarburized area; (2) there is from the start of diffusion an unknown carbon-concentration gradient between the steel and the decarburized area. Another method, which possesses neither of these disadvantages, is to study diffusion from steel into a thick plating of electrolytic iron. Herc the chief difficulty is to secure an electrolytic deposit of iron upon steel without introducing an oxide film at the interface that will interfere with diffusion. The author is able to deposit iron upon any kind of steel without introducing an oxide film at the interface, so that diffusion of elements from the steel into the iron is free to proceed unhindered.

Jan 1, 1938

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleys1 and Gathmann,2- who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1964

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By A. S. Richardson

The recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont,., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By Robert U. King, John W. Vanderwilt

THE Climax molybdenite deposit in Lake County 100 miles southwest of Denver is located in the central part of the mineral belt extending northeasterly across the state. Principal geographic features and geology are shown on Fig. 1. The first period of molybdenite mining, which began in 1918, ended in April 1919 because of limited demand and a price drop to about 72¢ per lb. During this time the ore came from the Leal level and surface outcrops at a higher elevation. Rate of mining was 250 tpd and several million tons of ore averaging 0.7 pct molybdenite were developed. Since April 1924, when the second period* began, Climax Molybdenum Co. has been the only operating company. Production in 1924 was 400 tpd and finding ore was a continual problem. When the White tunnel was extended, however, further ore was encountered. The orebody was thought to be tabular until 1926, when B. S. Butler recognized the relation of the developed ore on the Leal and White levels to a central area of fine-grained hydrother-mal quartz, and by 1929 diamond drilling had blocked out indicated ore reserves in excess of 100 million tons. In 1946, on the basis of information obtained from 25 miles of mine workings and a completed exploratory program involving over 200,000 ft of diamond drilling, the present authors reviewed and brought up to date the geology of the orebody. More recently Sears," employing microscopic techniques, made a study of hydrothermal alteration and mineralization, and Howell and Schassberger'" restudied available geologic data. Production (1953) of molybdenite ore has been expanded to over 25,000 tpd and total production from 1918 through 1953 has been: Tungsten, tin, and pyrite are byproducts and monazite also was produced from 1949 through 1951, after which it was not saved. A maximum of 15 to 20 tons of monazite was produced. Geology of the Area Pre-Cambrian crystalline rocks constitute most of the Mosquito Range for several miles to the north, east, and south of the Climax molybdenite deposit, see Fig. 1. To the west the crystalline rocks are in fault contact with shales and sandstones of Pennsyl-vanian age. Both crystalline rocks and sediments are intruded by dikes and sills of Tertiary age. Numerous faults with small displacements are to be found in the crystalline rocks east of the Mosquito fault and in the sedimentary beds to the west. Pre-Cambrian Rocks: The pre-Cambrian rocks consist of schist and gneiss, identified with the Idaho Springs formation, and granite with minor pegmatite correlated with the Silver Plume granite of the Silver Plume area. The Idaho Springs formation is a general term applied to pre-Cambrian schist and gneiss found over a large part of the Colorado Front Range. At Climax this formation consists largely of biotite-schist and quartz-biotite gneiss with minor quantities of plagioclase and orthoclase, although in places appreciable quantities of feldspar and quartz are present in the more gneissic varieties. Locally, especially along the contact with granite, recrystal-lization of the schist has produced coarser texture and a more pronounced than average gneissic appearance. The gneiss and schist have been mapped as a single unit by Butler and Vanderwilt (1933)" and by Singewald (1951).12 Schist predominates at the higher elevations of the Mosquito Range and in the area to the north and east of Climax. The regional trend of schistosity is northeast with varying dips to the east. Silver Plume granite and associated pegmatite intrudes the Idaho Springs formation. Silver Plume granite in many places and in the Climax district in particular has an irregular form, and many large and small inclusions of schist and gneiss occur within the granite. Granite predominates at the surface in the immediate vicinity of the area of hydrothermal alteration and extends for several miles to the northeast and southeast. As more schist is present at lower levels of the mine than in the upper levels, the suggestion is that the granite is sill-like in form,

Jan 1, 1956

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By Aloys IL. Wollrab

The conditions that govern the selection of a suitable type of detachable bit for the small, isolated mine, for rock work and tunnel contracting and for the large mine are quite dissimilar, therefore intelligent recommendation of a particular make of detachable bit must involve consideration of many factors. Small, isolated mines may find advantageous a detachable bit that a larger mine cannot afford to use, because of more efficient conventional steel sharpening and steel-distribution practice, but a small mine may not be able to adopt the practice of large mines because of necessary capital expenditures for equipment for detachable-bit sharpening and . shanking. The perfect detachable bit, suitable for all conditions, has not yet been developed. Conventional Drill Bit in Use That drilling speed increases as the bit gauge decreases is well known, but since small-hole drilling is the exception rather than the rule the rate of such increase is probably not so generally recognized. Tests carried out by Holman Brothers Limited1 with 7/8-in. steel show that when bit sizes are reduced from I½ in., I3/8 in., and I3/16 in-; to I3/8 in., I1/4 in.., and I1/8 in., respectively, the volume of the hole is I 5 per cent less and the drilling speed 49 per cent higher. Recent tests by the United States Bureau of Mines2,3 in hard, uniform basalt showed that a reduction in average gauge from 2.077 to I,826 in., a difference of o.25I in., gave an increased drilling speed of 65 per cent. The limits to which a drill hole may be extended depend upon the loss in gauge. Since the conventional bit with 5° and 14° clearances did not possess sufficient reaming edge to permit the smaller gauge changes that were required for small-hole drilling, experiments were made in bit construction with a view to correcting this deficiency. This resulted in the adoption of the full reaming cross bit (having full Carr charac1erist.i~~) by some mines4 In order to drill holes having a minimum taper from the collar to the bottom of the hole, full reaming center-hole cross bits with 90° cutting angles, 5° and 14° wing tapers, forged on 7/8-in. quarter-octagon drill rods, are used in the conventional drill-steel practice at Hollinger. In the steel shop close attention is given to the condition of the dies and dollies, which, combined with a rigid inspection of the finished bit, ensures as nearly a perfect bit as call be forged economically. Shop practices and costs have been discussed in earlier paper.5,6 The method by which the radii for the special dies used for forging bits of different gauge diameter are obtained so that the points and reaming edges cut circles of the same diameter has been discussed by Hibbert. Requiremnts for Detachable. Bit for Hollinger Under these it it was appar- ent that it would be difficult to introduce a detachable bit that could successfully compete with the conventional bit already in

Jan 1, 1943

By F. W. Denton

Much has been written about the possibilities of the Vermilion and Mesabi ranges of northern Minnesota as producers of large quantities of high-grade iron-ore. The Mesabi range in particular has attracted considerable attention on account of the proximity of the ore-deposits to the surface, which has been as-

Jan 1, 1898

By Clarence E. Jackson, George G. Luther

The ever increasing array of information concerning the measurement of the effect of the welding process on the properties of a steel is an indication of the tremendous effort that is being expended in this field. The methods that have been considered may be divided into two groups: first, those that measure directly the effect of welding on the ductility of a steel, and, second, those that observe the change in some property, such as the hardness of the heat-affected zone, and assume a direct correlation between this change and the resultant ductility. The nick-bend test is a direct method designed for studying the effect of welding on the ductility of a steel. The test specimen (Fig. I) consists of a bar cut from a plate with a bead weld on the surface. The specimen is prepaxed with a saw-notch placed so as to restrict deformation to the heat-affected zone under the bead weld when tested as a static bend. Failure is caused by rupture of the low-ductility metal in the heat-affected zone. The angle at maximum load is used as an index of the effect of the welding process on the material. In the development of the nick-bend test considerable scatter was noted in some of the results, although the agreement of duplicate specimens welded at the same time and tested consecutively was excellent. Upon further investigation it was found that the change in ductility was dependent upon the interval of time between the welding operation and the testing of the specimen. For the six steels of Fig. 2, the angle at maximum load in lour cases was doubled and in one case was tripled. All steels that have been studied show an improvement in the angle of bend for longer intervals between welding and testing. This same behavior has been found in weldability tests using the Navy T-bend

Jan 1, 1945

By V. A. Phillips

Transmission-electron micrographs of electro-thinned samples of bulk-aged Cu-3.1 pet Co alloy show an aging sequence, supersaturated solid solution — coherent particles — quasi -coherent particles — noncoherent particles. Hardening is due to precipitation of coherent spherical fee coball-rich particles showing coherency strain fields, which are resolved at between 15 and 30A diameter. Loss of- full coherency did not occur until well into the overaged region, even with the assistance of deformation after aging. Different average particle diameters of 123, 92, and 149 ± 10Å were observed in samples aged to peak yield strength at 600°, 650°, and 700°C, respectively, indicating that there is no critical size for peak hardening. Noncoherent particles tended to develop (111) faces and became octahedral in shape. Dislocations tended to nucleate spherical coherent particles which eventually grew together forming large elongated particles. The surface energy of a noncoherent (low-angle) inter-phase boundary is estimated to he about 50 ergs per sq cm. A number of particle lining-up phenomena were observed. Overaging is principally attributed to increase in particle spacing, progressive loss of coherency, and increase in amount of discontinzdous precipitation. COPPER dissolves about 5.6 at. pet (5.2 wt pet) of cobalt at 1110oC1 and the solubility decreases to 0.75 at. petl (0.54 at. pet)2 at 650°C and to 0.1 at. pet or less at lower temperature.' It has been known for many years3-5 that Cu-Co alloys are capable of age hardening. Since cobalt is fee above 417°C and its atom size is only about 2 pet smaller than that of copper, precipitation of coherent particles would be expected. The equilibrium phase precipitated at 700°C and below contains about 10 pet Cu in solution which tends to stabilize the fee structure, lowering the transformation temperature to 340oc.l The alloy is known to undergo discontinuous precipitation in addition to general precipitation; while the former can be seen with an optical microscope, the latter precipitates are not visible except in the grosly overaged condition.5, 6 Extensive use has therefore been made of the ferromagnetic properties of the precipitate in order to follow the course of aging, and it has proved possible to measure the average particle size, spacing, approximate shape, and volume fraction and to determine that the particles are coherent without ever seeing a particle (see for example Refs. 2, 7, and 8). The magnetic measurements of particle size are limited to diameters below about 120Å.7 The present study was undertaken using the techniques of transmission-electron microscopy in order to check the above conclusions, to extend the previous magnetic work to larger particle sizes, and to attempt a more detailed correlation of properties and structure. A portion of this work has already been published.9-11 The present paper is concerned with the metallographic features of precipitation in relation to aging curves. Bonar and Kelly12'13 have published preliminary results of a similar study on single crystals of Cu-2 at. pet Co. EXPERIMENTAL Preparation of Alloy. A Cu-Co alloy, containing 3.12 wt pet (3.36 at. pet) Co by analysis, was prepared from 99.999 pet purity oxygen-free copper and electrolytic-grade cobalt. The alloy was melted and cast in vacuo in a high-frequency furnace using a graphite crucible and mold: Analysis showed chat 0.004 pet C was picked up during melting. The 1-1/2-lb ingot was homogenized in hydrogen for 24 hr at 1000°C. Slices were cold-rolled to 0.005 or 0.003 in. thickness, with an intermediate 650°C anneal in hydrogen at 0.080 in. thickness. Batches of six to ten strips were solution-treated in sealed-off quartz tubes in high vacuum in a vertical furnace and quenched by dropping into iced brine containing a device which snapped off the nose of the tube. Solution treatment consisted of 1 hr at 990°C or 2 hr at 965°C. The latter was employed for all mechanical-property studies, since a tendency was noted for the higher temperature to give porous material. Strips were usually aged individually in a horizontal vacuum furnace, inserting into the hot zone and withdrawing into a cold zone without breaking the vacuum. This method gave a rapid heating rate, permitting the use of short aging times. In some cases, particularly for the longer aging times at the higher temperatures, samples were sealed individually in quartz tubes in high

Jan 1, 1964

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By C. L. Pillar

TWO shafts have been completed since the spring of 1948 when underground development started, and three are now under construction. The new program provides two main ore shafts, Nos. 3A and 3B, spaced 195 ft apart and located on the south- western end of the orebody. It is planned that eventually 35,000 tons of copper ore per day will be hoisted by these identical four-compartment shafts. The third shaft of this new group is 600 ft from the present No. 1 shaft and will provide caged sup- plies for the underground mining operations. This No. 4 shaft has the largest cross-section of any shaft in Arizona.

Jan 7, 1954

By Joseph Moses Botbol

This study was designed to demonstrate the viability of using high-frequency radio transmission as a means of communications between a remote field camp and a time- sharing computer system. A field camp near Johnstown, Pa., was linked by high- frequency radio to a base station 160 miles to the southeast in Vienna, Va. The base station was in turn linked by telephone to a time-sharing computer system near Los Angeles, Cal. Error-free data transmission utilized highly stable receivers and transmitters, forward error correction, and dual-frequency diversity. Three geologic applications programs resident in the Los Angeles computer were executed from a graphics cathode ray tube terminal in the field. Bulk data equivalent in volume to 4 days of typical spectrographic analytical work generated by one spectrograph and one spectrophotometer were transmitted from the field to the base station. All programs, were executed successfully, and all data were transmitted error free.

Jan 1, 1976

By M. R. Pickus, C. H. Mathewson

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centcred cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers," were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938