Search Documents

By A. N. Winchell

In connection with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Ringham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance. • Sandstone-limestone Gradation The sedimentary rocks of the Bingham district are chiefly sandstones, with some beds of limestone, all now lying with their strike nearly east and their dip nearly north at an angle of about 30°, near the surface. The limestone beds are remarkably irregular in thickness in some places, but usually change very slowly in composition along the strike. However, the most interesting results are obtained from a study of a section across the beds at right angles to the strike. In some places, such sections show the usual alternation of pure sandstone with nearly pure limestone, in the simple manner assumed in most geological discussions.

Jan 1, 1924

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves (1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worthless or harmful impurities, and (4) the profitable disposal of the product. The fist step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1964

By M. C. Leverett, M. E. True, W. B. Lewis

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By W. B. Lewis, M. E. True, M. C. Leverett

This paper states the theory underlying the design of two kinds of dimensionally scaled models of parts of idealized oil fields. One of these simulates an oil well and its surrounding sand for a distance of 16 ft. radially from the well. The other model simulates linear flow through layered sands. Construction and operation of the models are described and typical data are given. The unique features in the design of the models are: (I) the treatment of the permeability-viscosity quotient as a single variable and (2) the use of previously reported experimentally developed relations between relative permeability and saturation and capillary pressure, saturation, porosity, permeability and interfacial tension. The models at present simulate flow of oil and water only, through unconsolidated sands. They are superior to unscaled models, which may give rise to erroneous conclusions. The models are designed to study the desirability of various methods of well completion and the effects of various factors on recovery of oil from layered sands. Introduction Recent work on the fundamental behavior of flowing mixtures of fluids in sands has resulted in the development of some new theory in this field, much of which has been presented in previous papers.l-4 However, the application of this theory to the behavior of oil wells or oil fields has proved too complicated for ordinary mathematical techniques, except in very highly simplified cases. A practical solution to this problem appears therefore, to lie in the use of dimensionally scaled models of elements of oil fields. The object of this paper is, first, to present the theoretical and experimental basis of the design of such models, and, second, to describe their construction and operation. Experiments now under way on the models already built will yield material for other reports, which will be devoted to interpretation of the results in terms of oil-field behavior. So far, simple dimensional models of two kinds have been built and are being operated. These models represent different parts of an idealized oil field but obey the same underlying theory. The only fluids represented are oil and water, since certain questionable approximations are necessary for gas-liquid systems. General Theory Dimensional models have been used in other fields for a long time, and their theory is adequately given in the literature. 5 Here, it suffices to state that each physical element entering into a dynamic relation may be given a definite description in terms of three fundamental, but arbitrarily chosen, dimensions. These usually are mass, length, and time, symbolized here by the small letters m, I, and t. Two systems are said to be dimensionally similar or dimensionally scaled if for each element in one system there is a corresponding element in the second system and the ratios of the numerical magnitudes of corresponding elements are constant for all elements of the same dimensional type.

Jan 1, 1942

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress .4,5† The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed .27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By Albert Hill Fay

In giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N 65° 35' and long. W. 168o. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the Westernmost point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions arc of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption " The Land's End of Two Worlds." "The Arctic Ocean encircles with a belt of eternal ice, the desert confines of Siberia and North America—the uttermost limits of the Old and New World, separated by the narrow channel known as Bering's Straits. " To the north, this desert is bounded by a ragged const, bristling with huge black rocks. At the base of this Titanic mass lies enchained the petrified ocean (Bering sea) whose spell-bound waves appear fixed as vast ranges of ice mountains, their blue peaks fading away in the far-off frost-smoke, or snow-vapor. " Between the twin peak* of East Cape, the termination of Siberia, the sullen sea is Been to drive tall icebergs across a stream of dead green. There lies Bering's Strait. Opposite, and towering over the channel, rise the granite masses of Cape Prince of Wales, the headland of North America. "These lonely latitudes do not belong to the habitable world."

Jan 1, 1908

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. How- ever, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred ,at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed ,as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

There are two types of shovels currently used primarily as mining tools-the stripping shovel and the quarry-mine (Q-M) shovel. The two types have basically the same features, the main difference being in size. The stripping units are giant four-crawler shovels that operate by placing overburden alongside in a mined-out area. The Q-M units, on the other hand, are two-crawler shovels that usually load into trucks or trains. Powering Systems A typical stripping or Q-M shovel is fully electric, receiving power through a trailing cable that is connected to a large motor-generator set with multiple generators. In the full Ward-Leonard system, each generator furnishes d-c power to separate motors which drive the mechanisms for the principal motions of the shovel-hoist, crowd and swing.

Jan 10, 1967

By John Drew Ridge

For the early conservationists before the first decade of the twentieth century, conservation meant largely the planned preservation of water, forest, soil, and wildlife resources-renewable natural resources-through efficient use. Water was primarily thought of as a resource that must be kept available for humans to enjoy in a recreational sense and as a habitat for wild animals, birds, and fish. Little thought was given to conserving water for actual human or industrial needs. If industry entered the picture it was as an actual or potential polluter of water, which was the basic necessity for drinking and bathing and for outdoor recreation. Even the forests were only held worthy of conservation largely because they were areas in which wildlife could, or should, abound and in which human beings might find relief from the cares and problems of everyday life. Finally, the soil was to be preserved in its natural fertility through proper fertilization, cultivation, and crop rotation; in this the conservation program did enter the realm of the practical. For through soil conservation, the world was to be able to raise increasingly large crops of constantly improved organic foods which the steadily growing population of the earth was to need to survive and improve. Relatively little time, however, was spent on considering what profit the farmers of the world were to make from the scientific farming on which they were to embark. In short, the appeal of the early conservationist program was much the same as that of the entire era of Theodore Roosevelt of which it was a part; it was to the heart rather than to the mind; it was to emotion rather than to reason. Because of the way in which the problem was approached, conservation took on the character of a crusade rather than that of a practical plan for the betterment of man through economically sound methods of improving his environment and the uses he makes of it. Conservation had, then, all the advantages of a stirring appeal to the emotions, but it did not have the lasting results that would have been achieved by a program with a sound economic basis.

Jan 1, 1959

By A. J. Bartlett

ISLAND Creek conditions are generally referred to as ideal; yet, as at all other properties, there are all known hazards of coal mining. The hardest of these hazards to combat is the human element. The basic thought in the minds of the management of these properties is to produce coal with the utmost safety, and it has impressed upon its supervisory force that it does not want a ton of coal unless it can be produced safely. This company has instituted a mine inspection department, which reports direct to the general manager, and all matters pertaining to safety come under the direction of this department. Through the medium of the inspection department, the management is kept in touch with the actual conditions existing in general at all mines. Inspections are made regularly and continuously; that is, at all times while the mines are in operation some sections of some mines are being examined. These inspections cover all active and inactive workings. Miners are con-tacted in their working places and other employees at their respective work. A thorough check is made to see that the state mining laws are complied with and that company safety rules are being observed. Night shifts receive the same attention as day shifts. All violations and dangerous practices are brought to the attention of the plant supervisory force with suggestions and recommendations; major hazards of emer-gency nature are taken up immediately with the management. Peri-odical inspections are also made of all tipples, preparation plants, dumping and hoisting equipment, to see that all machinery is properly guarded, and walkways and platforms properly fenced; conditions of equipment and mechanical defects are also reported. Reports of inspection are written in letter form and in such a manner as to give the management a picture-of the existing conditions at the time of inspection. Copies of inspection reports are forwarded; to the superintendents with the general manager's comments.

Jan 1, 1937

DISCUSSION, G. Derge and D. J. Girardi presiding N. A. Gokcen (Michigan College of Mining and Technology, Houghton, Mich.)—While the authors present very interesting results on the effect of sulphur upon the solubility of oxygen, they have not established convincingly the lines of two-fold saturation (the valleys in Fig. 2) and the ternary eutectic point. Their contention that sample S-7, upon melting at

Jan 1, 1954

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

THE metal iron has physical arid chemical properties which are some- what different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron the former being the ordinary form at room temperature. When heated above the "A2 point," 769 C (1416 F), the metal becomes nonmagnetic, and at the "A3 point," 911 C (1672 F), it undergoes a change in crystalline form to become gamma iron. 111 the range 769 to 911 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1392 C (2538 F), it changes into delta (d) iron, which is identical with beta or nonmagnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1536 C (2797 F); the melting point is generally lowered by alloys or impurities. PHYSICAL AND THERMAL PROPERTIES OF IRON Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A3 point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly with the range of stability of a given form, but this is not always true. For ex- ample, the specific heat reaches a sharp maximum at the A2 point al- though no transformation occurs. (See Fig. 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an appreciable extent. Table 16-2 contains a list of the common elements classified with respect to their solubility in liquid iron. Those which are very soluble or practically insoluble require no further discussion, but several of the nonmetals that are gases and exhibit limited solubility are of considerable importance to us and merit more detailed consideration.

Jan 1, 1964

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb'24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.' as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By J. R. Low, A. M. Turkalo

ManY qualitative observations have been made concerning the relationship of the carbide dispersion and the mechanical properties of steel. With reference to the strength and hardness we know that for a given composition a steel having a fine pearlitic structure is stronger than that having a coarse pearlite. The martensitic structure tempered at a relatively low temperature and having finely dispersed carbides gives greater strength than that given by the martensitic structure tempered at a relatively higher temperature and having a coarser

Jan 1, 1959

By J. J. Casey, R. S. Busk, D. L. Leman

The mechanical properties and the phase-temperature relationships of magnesium-lithium-aluminum, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys are presented. It is shown that the strengths of some of these alloys can be tripled by heat treating and aging but that the high strength is accompanied by brittleness and lack of stability. MAGNESIUM-LITHIUM alloys are interesting because the hexagonal structure of magnesium can be changed into the more ductile and workable body-centered cubic structure by the addition of only 10 pct lithium.1 After Loonam2 determined that the ductility of the magnesium-lithium alloys is destroyed by even trace quantities of sodium, it was possible to prepare ductile alioys and study their mechanical properties. Jackson3 and coworkers have ably described their results with both the binary and polynary magnesium-lithium alloys. The present paper is a report of the mechanical properties of wrought magnesium-lithium-aluminurn, magnesium-lithium-zinc, and magnesium-lithium-aluminum-zinc alloys. Experimental Procedure The alloys were made by melting 7 lb of magnesium in a steel crucible under a molten flux of 75 pct LiCl + 25 pct LiF3 previously dried at 1600°F. The metal was heated to 1300°F for alloying aluminum and zinc and then cooled to 1250°F for adding lithium (sodium content: 0.01 to 0.04 pct). After the lithium had been alloyed, dry LiF powder was sprinkled on the melt to thicken the excess flux. After a 15 min holding period, the flux was skimmed off. Paraffin vapors were used to protect the metal as it was poured into 3 in. diam by 11 in. long magnesium molds. Billets were extruded into 3/8-in. diam rod and 1/16 x 3/4-in. strip; sheet was prepared from 1/8x 7/8-in. extruded strip, first by hot rolling and then by cold rolling 2 pct per pass. Hot rollability, or the temperature range through which the alloys could be rolled, was determined by rolling the strip two passes at 30 pct reduction per pass. Cold rollability, or the percentage of cold reduction to cause detrimental cracking, was determined on 0.064-in. hot-rolled sheet. Standard ASTM procedures were followed to obtain the mechanical properties, using 0.2 pct offset for the yield strengths. The level of properties produced with commercial magnesium alloys using the procedure described is given in a previous publication." Results Magnesium - Lithium - Aluminum System: The good workability of magnesium-lithium alloys is illustrated by the data in table I, which shows approximately how the extrusion pressure decreases as the amount of cubic phase increases. Binary magnesium-lithium alloys are soft and weak, but aluminum raises their strengths con-

Jan 1, 1951