Search Documents

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By George D. Dub

Owens Lake is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.-2H2O) and borax, (Na2B4O7.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. Closed Basins Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride, brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I. Chloride type; largely sodium chloride (NaC1) and of oceanic type, such as Great Salt Lake. Related is -the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. a. Sulphate type; largely sodium sulphate (Na2SO4) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate—chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate—Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1948

By Noah Fields Drake

During July and August, 1899, the writer took advantage of an opportunity of going to Shansi to gather some information concerning the geology and value of the already famous coalfields of that province. The long journey, mainly on slow river-boats, and the limited time at command, allowed only about ten days of work to be done in the coal-fields around Tsê Chou. The geologic structure and the rock-formations were found to be simple and quite regular, so that in that time the accompanying sketch-map (Pig. 1) was made, and a fairly good idea of the distribution of the coal and general geologic features was obtained. The map was made by measuring a base-line about three-quarters of a mile long, triangulating for principal points over the field, and filling in the details by rapid sketches. The few elevations marked on the map were taken with an aneroid barometer. Only a few of the great number of towns and villages that are within this densely populated area are shown; and the coal-mines indicated are not the only ones within the area, but the ones where most of the following information about the coal was obtained. The value of this coal-field was first clearly set before the scientific and commercial world by Baron von Richthofen,* who made a geologic reconnaissance of Shansi in 1870. Since that time the hostile attitude of the Chinese government and people towards foreigners and their enterprises has kept the coal-fields from being developed. But the last few years of rapid change in the conditions of China have at last apparently opened a way for the exploitation of this coal-field. The Peking syndicate, a joint English-Italian company, now has concessions from

Jan 1, 1901

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

By H. Ries

INTRODUCTION OF the several interesting physical properties of clay which have claimed the attention of investigators in recent years, none is more important than the behavior of the material when heated to temperatures above those of dehydration. Some of the problems to be solved are: 1. The mineralogical changes that take place in firing. 2. The relation between temperature and change in constitution, shrinkage, porosity, etc. 3. The importance of the time factor, as duration of firing, either in reaching a given temperature, or of exposure to a constant temperature. Mineralogical Changes As a result of fusion, reactions take place between the constituents of a clay, which results in a reorganization of the mass, and the formation of new compounds. Of the new minerals developed, sillimanite is the one usually recorded, and has been referred to by a number of observers.1 There appears to he a difference of opinion, however, regarding the temperature at which it is formed. Thus. Klein2 notes that sillimanite forms only above. 1300° C., while Mellor claims that it can develop below 1200° C., the difference in results being conditioned by the time factor. In Klein's experiments the test pieces were fired in 12 hr., while in Mellor's, the temperature rose from 800° to 1180° in 24 hrs., and occupied the same time in cooling back to 800°.

Jan 9, 1917

By George K. Foster, Charles D. Borror

THE Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest openpit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. THE ORE BODY The ore body is a serpentinized peridotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur perpendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber [ ]

Jan 1, 1946

By H. Rosenthal, A. L. Jamieson

THE action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking. Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,' who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. METHODS Specimens Two types of specimen were used: I. Unannealed 70-30 brass cups formed from 0.040-in. thick sheet. Height of cup was 1 3/8 in. and diameter was 1 7/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass). The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was preceded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (I) degreased in trichlorethylene, (2) rinsed in H20, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 sp. gr.), (4) rinsed in H2O, and (5) dried. Amines Tested In selecting the amines, representatives of the three series of amines and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By Sylvan Cromer

The need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investigator1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happenings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quantitative results for air-water flow. Experimental Apparatus and Procedure The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1940

By William E. Ford, Edward Salisbury Dana

General Principles of Optics Optical Instruments and Methods General Optical Characters of Minerals 1. Diaphaneity 2. Color 3. Luster Special Optical Characters of Minerals belonging to the different Systems A. Isometric Crystals B. Uniaxial Crystals General Optical Relations Optical Examination of Uniaxial Crystals C. Biaxial Crystals General Optical Relations Optical Examination of Biaxial Crystals 306. Before considering the optical characters of minerals in general, and more particularly those that belong to the crystals of the different systems, it is desirable to review briefly some of the more important principles of optics upon which the phenomena in question depend. For a fuller discussion of the o tics of crystals, special reference is made to the works of Groth (translation by Jackson), Liebisch, Mallard, Duparc and Pearce, Rosenbusch (translation by Iddings), Iddings, Johannsen, Winchell, mentioned on p. 3 also to the various advanced text-goks of Physics. 307. The Nature of Light. - Light is now considered to be an electro- magnetic phenomenon due to a periodic/variation in the energy given off by vibrating electrons. This energy is transmitted by a series of periodic changes that show all the characters of ordinary wave phenomena. The light waves, as they are commonly called, possess certain short wave-lengths that are of the correct magnitude to affect the optic nerves. Other similar waves with longer or shorter wave-lengths belong to the same class of phenomena. Immediately beyond the violet end of the visible spectrum come the so-called "ultra- violet" waves with still shorter wave-lengths and on beyond these we have the X-rays and the "gamma" rays produced by radium. Of the waves having greater lengths than those of light waves we have the waves that give

Jan 1, 1922

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By John L. Burns

The object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-hardening characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classification" is essayed. A.—Relation of Lattice Parameter and Electrical Conductivity to Changes in Physical Properties Due to Aging of Fe-C Alloys Since Whiteleyl in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A, point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,~ and at the same time and independently, W. Koster,~ proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By J. E. Johnson

Charcoal-iron is quantitively so unimportant compared with coke-iron, that its qualitative importance for many industrial purposes is entirely unkriown to many coke-furnace-men, and to the great majority of the inembers of this Institute. To explain this qualitative importance, and explain some of the fact,ors that affect the quality, are the objects of this paper. A brief review of' the commercial conditions governing the charcoal-iron industry is a necessary preliminary to any adequate treatment of the subject. The advent of coke-iron, which transformed the whole iron industry commercially, left intact a limited production of charcoal-iron in the East and South, which has been conducted almays on the basis of high cost and high quality, with correspondingly high selling-price. In the Northwest, particularly in the Lake Superior district, the development has been along totally different lines, for which the close proximity of the great iron-ore deposits and the great forests of that region mere responsible. When the great white-pine forests were removed there were left behind large areas of hardwood and hemlock, to which little attention was paid in the prosperous years of the white-pine industry. But when the latter declined, the demand for lumber, and the presence of lumber-men, probably more skilled than any others in the world, caused the gradual introduction of these woods into commercial use. It was a matter of ancient knowledge that hardwood made an excellent charcoal, and to utilize the cordwood left after the saw-logs were removed, by converting it into charcoal and using it to smelt ore from the adjacent mines, mas an obvious step. In some cases the establishment of the furnace occurred in-

Jan 1, 1913

By R. E. H. Pomeroy

EARLY in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (1) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application; the coal and air mixture can be piped where needed. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins.

Jan 2, 1920

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj' V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.' had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

By J. W. Axelson, J. N. S. Kwong, J. T. Adams, E. L. Pire, J. F. Johnson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental understanding of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1—the mechanism of the fracture process itself, 2— the particle size distribution of the crushed product, and 3—the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced. Fracture of Solids This phase of the crushing problem is the most fundamental because it is concerned with the actual mechanism of fracture. The main problems in a study of the fracture process are concerned with the questions of why and how fracture occurs and why there is such a discrepancy between the actual and theoretical energies needed in a fracture process. In considering the how of fracture, Poncelet40 carried Out experiments On the crushing of glass under compression. Actual photographs were taken of the glass plates in various stages of fracture-From these experiments Poncelet was able to postulate a probable mechanism of fracture. Probably because of the quantitative nature of the problem, considerable effort has been expended to find an explanation for the low tensile strength of materials and the conversely high energy for crushing. Tensile strengths are often only 1/500 of the theoretical while the energy for crushing is usually at least 500 times the theoretical. A review of the work to explain the low strength of glass is given by Weyl,52 in which the work of Griffith," Joffe,32 and Powell and Preston " are discussed. In a recent paper Seitz46 holds that the presence of flaws and fissures, as originally expounded by Griffith, is the most probable reason for the low strength of metals. Since a mass of data has been accumulated on the fracture strength of materials, several investigators have attempted to correlate this data in the form of an equation. Glathart and Preston," Taylor,40 Ponce-let,40 Machlin and Norwich," and Frederickson and Eyring,20 have all considered this problem, and the final relationship has always been that the stress for fracture is proportional to the logarithm of time. Murgatroyd30 arrived at a very similar relationship by a different method. The study of the fracture process has used many methods. Among some of these are the thermody-namic approach used by Furth21 which was based on the work of BornxL and later used by Saibel,43 and the statistical method applied by Fisher and Hollo-mon.10 In recent years metallurgists have concerned themselves with the problem of brittle .fracture as opposed to the usual plastic failure of metals. The great amount of interest shown is reflected by the number of contributors to the recent symposium on the fracture of metals.' Repeated failures of welded ships during World War II have accelerated these Studies.31,50,34 The shifting of thought from an emphasis on the

Jan 1, 1952

By Horace Mann

A FEW years ago, it was generally thought that from 15 to 18 per, cent. of zinc oxide was the upper limit of a workable lead blast-furnace slag. With slags above this zinc-oxide content, the furnaces gave so much trouble because of hearth, wall, and crucible accretions that the campaign was very short. The time lost in cleaning out the frozen furnaces, for it was seldom possible to blow them out, and blowing in was so great that it was considered uneconomical to attempt the running of high-zinc slags, even if this were metallurgically possible. It is true that there are, references to one or two slags much higher in zinc than the foregoing,1 but the average smelterman regarded these, as freaks and not to be considered for regular furnace work. One or two plants, notably the plant of the United States Smelting Co, at Canyon City, Colo., ran charges, higher in zinc. At this plant, the zinc-oxide content of the charge was frequently 20 per cent. and higher but the slags from these furnace's seldom ran over 10 to 12 per. cent. zinc oxide. The furnaces were run with a large volume of air under a relatively low pressure, a low smelting column, and a very hot top; as a result, a large amount of zinc was volatilized. Even with the low smelting column and hot top, accretions caused much trouble and barring, down was a daily occurrence. At the time most of the theories on lead blast-furnace work were promulgated or worked out, it was necessary to run a furnace with a cold top in order to avoid an excessive loss due to fines and fume. At the same time, the smelting conditions had to be such that the lead and silver would be reduced and would enter the bullion. The slag had to be liquid but the charge must not give excessive accretions either in the hearth or on the walls of the furnace. This forced the operators to run the furnaces with a comparatively low blast, which, in turn, caused a small fuel consumption per unit of time with the accompanying result of a low working temperature.

Jan 8, 1925

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By J. J. Beeson

The second part of the paper includes a detailed account of the processes of secondary-enrichment which have been effective in producing the disseminated ores. While both parts present new features, it is hoped that the discussion on secondary chalcopyrite and bornite may be of interest to those who are engaged in the study of secondary processes in other districts. The excellent work' Economic Geology of the Bingham Mining District, by J. M. Boutwell, was published in 1905. Since that time the extensive development work-surface cuts and underground drifting-of the Utah Copper Co. has made possible the collecting of samples for more detailed microscopic study. The writer has taken advantage of this fact and presents the following work, not as a criticism, but as a' continuation of the work which was begun by Mr. Boutwell. b. Acknowledgments.-The present study was undertaken at the suggestion of Dr. A. F. Rogers; to him, and to Prof. C. F. Tolman and Prof. S. W. Young, the writer wishes to express his thanks for criticism in the preparation of this paper. The writer also expresses his thanks to D. C. Jackling, Vice-President and Managing Director of the Utah Copper Co., for permission to publish this paper, and to William Spencer, D. W. Wadleigh, T. S. Carnahan, J. A. Caulfield, Percy Dayer, and Edward Norsefall, for the courtesies extended to him while a co-worker in the mines.

Jan 11, 1915

By Victor Homerberg

A STUDY of the correlation of the mechanical properties, and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the manufacturer. The results obtained by Babson and Buhler,1 Bengough and Hudson,2 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470° C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200° C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a ¾ -in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 3, 1924