Search Documents

By T. M. Broderick

INVESTIGATIONS into the possibilities of economically mining and concentrating low-grade iron ores of the Lake Superior region are attract-ing increasing attention. Among the organizations that are carrying on the work are the United States Bureau of Mines, the State of Minne-sota (which spends about $80,000 annually on problems of the 'iron and ferroalloy ores of Minnesota), and the State of Michigan (which spends about $10,000 annually of its iron-ore research). Several of the mining companies are also financing research. Of the states in the Lake Superior district, Minnesota has done most in iron-ore concentration. In 1930, thirty-seven concentrating plants were in operation on the Mesabi Range, beneficiating about one-third of the total ore shipped. About one-half of these plants reduced silica; the others reduced moisture or improved the structure of the ore.1 Research into the possibilities of magnetic concentration of the Eastern Mesabi magnetite ores indicates that vast tonnages of that ore may be utilized at a profit in the not distant future. Magnetic concentration has also been tried at Sellwood, Ontario, on the Moose Mountain deposit, and at the Berkshire mine in Wisconsin on the magnetic ores of the Western Gogebic Range. There have been few attempts to concentrate Michigan iron ores. In order to determine the possibilities of such concentration, iron-ore research has been carried on at the Michigan College of Mining and Technology for the past few years. After a general survey of the iron ores of the state, a program of more detailed experimentation was out-lined, starting with work on the Ironwood formation of the Gogebic Range. The results of this research led to the belief that gravity methods will produce fairly satisfactory concentrates from the parts of the iron formation that are made up of comparatively thick alternating beds of rather high-grade ore and lean chert.

Jan 1, 1933

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By Axel Hultgren

IN ingots of silicon-killed carbon steel made without addition of - aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially. In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents arid, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,10,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis17 and their amount to increase from the top downward in the axial region .2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form," by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.15 Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19,20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping' or of refractory material from various sources1,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistance to hydrofluoric acid, imparted by the alumina content. Silicate inclusions, are often referred to as. the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1948

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By A. W. H. Morris, E. A. Steigerwald

The jatzgue beizazriov oj Mietal matrix co))zpos~tes in tension -lensiom loading has been imestigated as a junction of Dolume fraclion veinfovcelnent using the model systems of a silver matrix reinforced with contlnuous or dzscontztinuous aligned tungsten jilamenls and continuous aligned steel filamenls. Appreciable impvocetnents in fatigue strength were obseved in all syslems inzvesLigated, the degree of sl renglhenng-increasing with increasing volume fraclion of reinforcement. The mode of fatigue failure was found to be a function of colutrre jp-actiotz and was also noted to be controlled by the relative fatigue and strength characlerislics of the matrix and reinforcemenl. THE advantages to be gained by suitably incorporating high-strength filaments or whiskers into metallic matrices are well-recognized.' To date emphasis has been placed on the experimental determination of tensile strengths and elastic moduli of metal matrix composites measured parallel to unidirectionally aligned filaments. Several attempts have been made to relate experimentally measured tensile properties to theoretical values calculated from the properties of the components on the basis of the relatively simple "rule of mixtures" analysis. However, relatively few data have been reported in the literature on the fatigue behavior and mechanism of fatigue failure of metal matrix composites. In a study of fatigue crack propagation in aluminum plus steel wires and aluminum plus tungsten wires, Forsyth et a1.2 found that the incorporation of small numbers of filaments suitably dispersed were capable of substantially reducing the rate of fatigue crack propagation. For this purpose, the strength of the filaments appeared to be more important than the aspect ratio and the authors reported that parallel filaments were not the most favorable orientation for increased strength. In a basic study of the fiber reinforcement of metals, Williams and 0'brien3 report preliminary results which indicate a considerable improvement in fatigue strength in reversed bending fatigue of a steel wire-reinforced aluminum alloy composite. In a study of the influence of interfacial bonding on fatigue behavior, Baker4 has also reported improved fatigue properties in stainless steel-reinforced aluminum composites. In contrast, Ham and place5 report that, although tensile properties are improved greatly by filament reinforcement, the reinforcement of copper with continuous, brittle tungsten wires up to 23 vol pct was comparatively ineffective against fatigue. The authors attribute the poor fatigue properties of the composite to fatigue hardening of the matrix at the tips of cracks which can build up stress concentrations sufficiently large to fracture proximate filaments. Baker and cratchley6 failed to find marked improvements in the reversed-bending fatigue properties of silica-reinforced aluminum. The study was complicated by the complex behavior in a composite during the compres-sive half-cycles imposed in this type of loading. This was manifested in the failure of the composites by de-lamination, a contributing factor being the presence of aluminum oxide at the matrix-filament interface. Prior to the general acceptance of filament-rein-

Jan 1, 1968

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By W. F. Holbrook, C. E. Wood, E. P. Barrett

The high-frequency laboratory induction furnace with a rotating liquid crucible enables research workers to conduct certain investigations heretofore very difficult or impossible to realize because vessels are not obtainable that are capable of resisting the physical conditions or the chemical actions to which they are subjected. Applications for patents covering commercial uses of centrifugal liquid crucibles were filed in the United States in 1919,' in France in 1925, in the United States and Germany in 1926,2 and in France in 1927.3 In 1928, Schuette and Maier,4 of the Bureau of Mines, reported the construction of a whirling table beneath a high-frequency induction furnace. Shape and Size of Centrifugal Liquid Crucibles When a vessel containing a liquid is rotated, the inner surface of the liquid takes the shape of a paraboloid under the simultaneous action of centrifugal force and gravity. The internal dimensions of the paraboloid rotating liquid crucible are governed by the diameter of the container and its speed of rotation. Melted Wood's metal was poured into cylinders 2 1/2 in. in diameter, which were rotated at 180, 300, and 468 r.p.m. When the metal was solid, a slurry of plaster of Paris was added, and rotation continued until the plaster had set. Fig. 1, a photograph of sections of the cylinders, shows the effect of speed of rotation of the containers upon the shape of the inner surface of the rotating liquid crucibles. Types of Furnaces Three types of high-frequency induction laboratory furnaces using liquid-metal crucibles were designed and constructed by the Blast

Jan 1, 1939

By J. R. Vilelia

IN accordance with the custom of this society, we are gathered here, as we have every year since 1924, to honor the memory of the eminent American metallurgist and teacher, Professor Henry Marion Howe. Unlike many of the distinguished metallurgists who have preceded me as a Howe lecturer, I cannot bring to you reminiscences of his personality, for it was not my privilege to be associated with Professor Howe, or to be directly one of his students. Yet, Professor Howe and Professor Albert Sauveur, through the medium of their books, were my first teachers of metallography, as they have been of almost all American metallurgists of my generation. As a teacher, and for many years the acknowledged leader of American metallurgists, he exercised a profound influence in the growth of our science and was held in honor by the men of science of his time. I can speak no words of technical appreciation that will add luster to his fame, for by his prophetic vision, his teachings, and his researches he stands among the immortals in the memory of all metallurgists. In 1926, the third Howe Memorial Lecture was presented by Professor William Campbell' of Columbia University, who entitled it "Twenty-Five Years of Metallography." He took as a starting date for his chronology the turn of the century, which coincided with his arrival from England to work in association with Howe at the Columbia School of Mines. In that informative lecture Professor Campbell enumerated the important advances in metallography achieved during the first quarter of the century, and, it now appears, may have established the custom of reviewing such progress every twenty-five years. The scope of Professor Campbell's lecture was as broad as his metallurgical knowledge, for it embraced a wide portion of the field of metallography, both ferrous and nonferrous. Twenty-five years later, the Howe Memorial Lecture Committee saw fit to assign to me the honor of writing a lecture that would commemorate the work of Henry Marion Howe and would at the same time constitute the 25th anniversary of the lecture by Professor Campbell. The Committee suggested that this lecture might properly be called "Twenty-Five More Years of Metallography," a suggestion that I have adopted. I must confess, however, that I have not followed the precedent established by Campbell and have narrowed the scope of this lecture to an appraisal of those achievements which in my opinion have contributed most to the progress of microscopical metallography during the past twenty-five years. Progress in Metallography The metallographic methods most widely used today, with the exception of the electron microscope, were firmly established more than twenty-five years ago. In general, our specimens were prepared for microscopic examination in those days in much the same manner as they are today. It is true that new details of technique have been introduced from time to time, and that superior equipment is available today, but on the whole, these improvements have been in the nature of refinements, often a matter of personal preference, and none can be considered essential to the attainment of the ultimate goal of the art and science of metallography, which is to reveal the structure of metallic specimens with unequivocal clarity so that they may be interpreted correctly. Mechanical metallographic polishing, which was the only method available in 1926, is still universally practiced and still consists of abrading the metallic specimen with a series of abrasives of increasing fineness until a specular surface is attained. We have now the alternative method of electropolishing, but it is not widely used because, except in a few special cases, its results are inferior to those of competent mechanical polishing. Likewise, most of the etching reagents preferred today were in common use more than twenty-five years ago and were applied in the same manner as they are today. Valuable improvements have been made in the optical and mechanical performance of metallurgical microscopes, but there was no dearth in those days of excellent instruments equipped with achromatic and apochromatic objectives capable of yielding micrographs comparable in quality with the best that we can make today. In fact, it would be a difficult task for any metallographer today to make optical micrographs at magnifications in excess of 3000 diameters that would surpass those made by Lucas more than twenty-five years ago. One of these is shown in Fig. 1. Yet, it is unquestionable that on the whole, the micrographs appearing in the metallurgical literature today are vastly superior to those

Jan 1, 1952

By J. Spotts McDowell

Preparation and Use.-Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for brick-laying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining 'the crude or lightly burned mineral at a temperature that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and C02; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brick-making in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1 to 2 in. (2.5 to 5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are filled. At most plants such holes, at the end of each week, are also

Jan 2, 1919

By D. W. Philips

The problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized rescarch began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications.' - Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the chief Mining Engineer of the Research Board, and was coordinated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: 1. To provide. by supports, means to prevent falls of fractured ground. 2. TO develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the properties of supports and their correct application. The second aspect is perhaps more fundamental, and involves also the properties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient frequency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1947

By D. W. Philips

The problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized rescarch began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications.' - Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the chief Mining Engineer of the Research Board, and was coordinated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: 1. To provide. by supports, means to prevent falls of fractured ground. 2. TO develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the properties of supports and their correct application. The second aspect is perhaps more fundamental, and involves also the properties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient frequency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1947

By W. L. Fink, R. S. Archer

THIS paper describes results obtained on aluminum-beryllium alloys and aluminum-beryllium-copper alloys in the preparation of which aluminum of 99.95 per cent. purity was used. The constitution and structure of the high purity binary alloys are given. The aluminum-beryllium eutectic occurs at 0.87 per cent. beryllium and 645° C. The solid solubility of beryllium in aluminum at 631° C. is 0.05 per cent. beryllium, and at room temperature is less than 0.013 per cent. beryllium. The densities of the alloys are substantially the same as the values calculated on the assumption that the densities of the elements are not changed by alloying. All of the alloys age-harden at room temperature after a solution heat treatment, and the chill cast aluminum-beryllium-copper alloys age-harden at room temperature without a prior solution heat treatment. Hardness and tensile properties are given. Salt spray corrosion tests on sheet specimens are described. It is shown that beryllium does not lower the corrosion resistance of aluminum to salt spray provided the alloy has received a solution heat treatment. COMMERCIAL POSSIBILITIES OF BERYLLIUM ALLOYS Beryllium has certain properties such as low density, high hardness, good corrosion resistance, low thermal expansion and fairly good electrical conductivity, which would indicate that it is worthy of consideration as an ingredient of light alloys. It was not until recently, however, that beryllium could be produced with sufficient ease to encourage research along this line. The production of beryllium by electrolysis from a fluoride bath has now developed to the stage where it could be used commercially if there were sufficient demand for the element. Claims made in certain newspapers and technical articles in regard to the strength and corrosion resistance of the aluminum-beryllium alloys are not justified by experimental results. Moreover, beryllium is an expensive metal ($200 a pound at the time this work was done) and, on account of the nature of its ore and the consequent difficulty of its extraction, it will in all probability continue to be a relatively expensive metal, although the cost would undoubtedly be a great deal less than $200 a

Jan 1, 1928

By Robert L. Frantz

Progress and improvement continue to be the bywords of a dynamic coal industry. The industry continues to gain strength and expand its horizons in the face of competition from atomic energy and the problems of restrictive legislation. The direct contribution of coal mining and transportation to the national economy is about $3 billion a year ac- cording to a study made by the National Coal Policy conference. Coal remains the backbone of the power industry producing almost two-thirds of all the electrical energy generated by fossil fuels and one-quarter of all the energy consumed in the nation. Power supplied by electric utilities increased 6.9% last year. The chairman of the Federal Power Commission predicted a 7.5% growth rate until 1980 for the nation's electric output. Some 80,500 MW of fossil fired power plant capacity are on order or under construction before 1974, compared to a present capacity, all sources, of about 290,000 MW. The comparable new additions of nuclear power plants is expected to total about 51,000 MW.

Jan 2, 1969

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By Y. A. Chang

Phase relationships in the system Cr-Si have been established based on the melting point, X-ray, metallo-graphic, and DTA studies. The three intermediate phases, Cr3Si, Cr5Si,, and CrSi,, melt congruently at 177V ± I@,Cr3Si, 1680"i 20°, and 1490" *20°C, respectively, while the fourth intermediate phase CrSi, melts peritectically at 1413" i 5°C to Cr5Si3 and a melt containing 51 at. pct Si. The temperatures and compositions of the four eutectic isotherms occurring in this system are given below: DTA and metallographic evidences indicate that Cr5Si, undergoes a phase transformation at 1505" i20°C. The high-temperature form of this phase could not be retained by the quenching techniques used in this study. TECHNOLOGICAL interest in the developing of composite systems, consisting of Sic on the one hand as a fiber-reinforced material and metallic substances such as chromium, nickel, or Cr-Ni alloys as a binding agent on the other hand, stimulated the present investigation of phase relationships in the binary system Cr-Si. Earlier works concerning this system have been evaluated and summarized by ansen and Anderko.' Their phase diagram was based mainly on the works of Kieffer, Benesovsky, and schroth2 and Kurnakov.~ According to these authors, the three intermediate phases Cr3Si, CrSi, and CrSi, all melt congruently at approximately 1730°, 1600°, and 1550°C. However, they did not agree on the compositional stability of the fourth intermediate phase between Cr3Si and CrSi. Later Parthe, Nowotny, and schmid4 determined the structure of this phase to be tetragonal T-1 type using the single-crystal method, and concluded that this phase had a formula of Cr5Si3. Since the compilation of Hansen and Anderko,' a new phase diagram for the system Cr-Si has been proposed by Elliott5 based on the works of Goldschmidt and rand,' Guseva and ~vechkin,~ and Trusova, Kuzev, and Ormont8 and the earlier works quoted by Hansen and Anderko.' According to this proposed phase diagram, all four intermediate phases have large ranges of homogeneity and all melt congruently. More recently, Svechnikov, Kocherzhinskii, and yupkog studied the system Cr-Si by the DTA-method. According to their findings, the three intermediate phases, Cr3Si, Cr5Si3, and CrSi,, melt congruently at 1700°, 1720°, and 1475"C, respectively, while the fourth intermediate phase, CrSi, melts peritectically at 1475°C to Cr5Si3 and a melt containing 50 at. pct Si. The temperatures and compositions of the four eutectic isotherms were found to be: In view of the discrepancies existing in the literature concerning the system Cr-Si, it was decided to rein-vestigate the phase relationships in this system. EXPERIMENTAL a) Starting Materials. Chromium disilicide and chromium or silicon powders were used in the present study to prepare the melting point and DTA samples. CrSi, was obtained by directly reacting cold-pressed elemental powders in an atmosphere of Hz at a temperature of about 1250°C. Chromium powder, purchased from Stark Chemical Co., had the following impurities in ppm: Fe, 200; Mg, 1000; and 0, 250; while silicon powder, purchased from the Welded Carbide Co., had the following impurities in ppm: Ca, 700; and Fe, 3500. b) Melting-Point Determination and Differential Thermal Analysis. Cylindrical melting-point samples of approximately 13 mm in diam and 30 mm in length with a rectangular groove in the center were prepared by hot-pressing of well-mixed powder mixtures in graphite dies. Before the melting-point determination, the hot-pressed samples were ground on a sand paper to remove any minute surface contamination of graphite. A small hole of 1 mm in diam, drilled on the center portion of the samples, served as a blackbody cavity for the temperature measurements. DTA samples approximately 13 mm in diam and 15 mm in length were prepared in a manner similar to the melting-point samples. Melting points were determined using the Pirani technique under a helium atmosphere of 40 psi. The design, performance, and operation of this apparatus have been described in detail by Rudy and ~ro~ulski.'~ The temperature measurements were carried out with a calibrated disappearing-filament-type micro-pyrometer. The measured temperature was corrected for losses from the quartz window of the melting-point furnace and for deviations from blackbody conditions of the observation hole. The procedure for temperature correction has also been previously described." The DTA method of Heetderks, Rudy and Eckertl' was also used to check any phase transformations of selected alloys in the system Cr-Si. It was not possible to make remated runs on the same sample once melt-

Jan 1, 1969

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

By Frederick O?Neil

SCOPE OF THIS REPORT THE object of this paper is to describe the present status and possibilities of liquid oxygen as an explosive based upon the investigations, research and practical work of the Ingersoll-Rand Co., and of the Air Reduction Co., from early in 1922 to date. The following work was done. 1. A study of the history and physical theory of L. 0. X. as an explosive. (No attempt will be made in this paper to give the history or theory, as this has already been covered by the literature on the subject.) 2. An investigation of the use and the practice with L. 0. X. in the iron mines of Lorraine where L. 0. X. has its largest application in Europe. Although L. 0. X. is extensively employed in the; iron mines of Lorraine, many of the mines using it exclusively, and blasting with it a total of approximately three million tons of iron ore per year, the fact that the mining practice in Lorraine1 is to drill comparatively shallow holes and blast only a few holes at a time, renders the data obtained there of very little value in estimating the possibility of replacing dynamite with L. 0. X. in American mining methods. In fact, in the iron mines in Lorraine, L. 0. X. replaced black powder, or its equivalent. 3. Laboratory research work on properties of absorbent materials. 4. Work in the Bureau of Mines explosive laboratory at Pittsburgh, Pa., on the properties of L. 0. X. cartridges. 5. Practical work underground with L. 0. X. cartridges in the Witherbee-Sherman iron mines at Mineville, N. Y. 6. Practical work in the quarries of the Calcite Quarry Co., Myers-town, Pa. 7. Practical blasting in several quarries and open-pit mines.

Jan 2, 1926