Search Documents

By R. H. Doremus, E. F. Koch

The first carbide phase that precipitates at 120°C from a iron containing about 0.02 wt pct, C was studied with the electron microscope. In both strained and unstrained material the carbide particles appeared to form on the dislocations in the iron, in agreement with the results of the kinetic study in part II. The structure of the carbide was tentatively identified as an expanded a-iron lattice (body-centered tetragonal) with about 0.7 wt pct C. This phase appeared to be metastable and apparently transformed into cementite or epsilon carbide when the iron was over-aged. WhEN a iron containing less than about 0.025 wt pct C is quenched from 700°C to room temperature the carbon is retained in solid solution and precipitates out slowly with time. The morphology and structure of the precipitating phase are still in doubt, two different carbide phases, epsilon carbide and cementite, have been identified, but there is considerable disagreement about the time and temperature at which they appear.1-4 Epsilon carbide seems to form at lower temperatures than cementite, although one group of investigators4 found only the latter phase over a wide range of aging temperatures. Usually these two phases have been identified after aging times much longer than needed to drain the carbon from supersaturated solution, at least for aging temperatures below 200oC. The precipitated carbides have been observed with the electron microscope,'-5 but again most results have come from samples aged much longer than necessary to reduce the carbon concentration in solution to a low value. In this study the carbide phases were observed in earlier stages of precipitation with the electron microscope, in order to learn more about the shape, size, and distribution of the carbide particles. Samples strained small amounts before aging, as well as unstrained samples, were studied, and the structure of the carbide phase was tentatively identified. EXPERIMENTAL "Ferrovac E" vacuum-melted iron, from which the wires for kinetic studies were also made (Refs. 6 and 7 and the following paper) was used for this work. An analysis of this material is given in Table I; it agrees well with the manufacturer's values. The number of inclusions in the iron was very small, as can be seen in the optical micrograph in the following paper. Pieces of iron about 1 mm thick and 5 to 10 mm in diam were used for all the studies except for those in which the sample was strained before aging; then the specimen was a rod 3 to 6 mm in diam and 20 cm long. The samples were held at about 700°C in wet hydrogen for at least an hour to remove residual carbon and nitrogen, after which they were heated to 950" (in the y region) and cooled to room temperature in the furnace. This treatment gave an average grain diam of more than 1 mm, so that the effect of grain boundaries on the precipitation process was negligible. The samples were carburized at 710°C for about 2 hr in hydrogen that had passed over toluene held at -30°C; then they were rapidly quenched into water. From chemical analysis this treatment gave a carbon concentration of from 0.012 to 0.016 wt pct, which is less than the solubility of carbon at this temperature. After quenching, the samples were aged at 120 "C in an oil bath for vari-

Jan 1, 1961

By R. Hastings Keller, Ralph E. Esarey

Oil and gas activities in Indiana during 1943 continued to decline at about the same rate as in 1942. New development, production, and prospecting, all showed the results of Federal regulation, low price for crude oil and shortages of labor and materials. Several local stripper-well operations were shut down, but no large-scale abandonment has occurred as yet. During the year, 277 holes were drilled for oil and/or gas, of which 99 were completed as oil wells, 19 as gas wells and 159 as dry holes. This record was a decline of 21 per cent over last year in the total number of completed tests, 20 per cent in the number of oil wells and 9.5 per cent in the number of gas wells. As in the previous year, most of the drilling (82 per cent) was in the southwestern part of the state, Gibson County ranking first, with 77 completions and 49 oil wells. Posey County was second, with 59 completions and 20 oil wells. The remaining 18 per cent of the drilling was in the old Trenton oil and gas area. The total footage drilled during the year was 482,799 ft., a decline of 18 per cent from the previous year. Of this, 146,559 ft. was wildcat footage. The total initial production of the oil wells completed was 6362 bbl. and of the gas wells was 2,562,000 cu. feet. Three tests in the old Trenton area were drilled into the Cambrian and reported nothing more than tar residue. A Devonian test was to be made in the Griffin field in the Wabash River but owing to the delay caused by Federal restrictions this test did not get started in 1943. It is expected to spud in March 1944. The new discoveries in 1943 were virtually all in the southwestern part of the state, and all, so far, one-well pools, except the North Owensville pool, in Gibson County. The latter was brought in during the month of February and by the end of the year nine wells were producing in the pool, with a reported initial yield of 1260 bbl. per day. By the end of the year it had a daily average production of 401 bbl. and an accumulated production of 39,129 bbl. The average gravity of the oil is reported to be 35.6. On the Ohio-Indiana state line, early in 1943, a new pool was opened up in the old Trenton area. The discovery well was on the Ohio side of the line. An offset well was completed on the Indiana side, with an initial yield of 64 bbl., and settled down to 5 bbl. per day. This well produced 1154 bbl. up to Dec. 31, 1943. There was no further development here, because of the Federal Conservation Order M-68, restricting drilling to one well on 40 acres. The development pattern usually followed in this area is one well to 5 acres. The E. Rogers field was extended by one pool (Table 4). Most of the development in the oil-field pools during the year took place in the Kirksville pool, in Gibson County, and the Caborn pool, in Posey County. The crude-oil production in 1943 was approximately 5,273,000 bbl., a decline of 29 per cent from the previous year. The Griffin field, of Gibson and Posey Counties,

Jan 1, 1944

By R. Hastings Keller, Ralph E. Esarey

Oil and gas activities in Indiana during 1943 continued to decline at about the same rate as in 1942. New development, production, and prospecting, all showed the results of Federal regulation, low price for crude oil and shortages of labor and materials. Several local stripper-well operations were shut down, but no large-scale abandonment has occurred as yet. During the year, 277 holes were drilled for oil and/or gas, of which 99 were completed as oil wells, 19 as gas wells and 159 as dry holes. This record was a decline of 21 per cent over last year in the total number of completed tests, 20 per cent in the number of oil wells and 9.5 per cent in the number of gas wells. As in the previous year, most of the drilling (82 per cent) was in the southwestern part of the state, Gibson County ranking first, with 77 completions and 49 oil wells. Posey County was second, with 59 completions and 20 oil wells. The remaining 18 per cent of the drilling was in the old Trenton oil and gas area. The total footage drilled during the year was 482,799 ft., a decline of 18 per cent from the previous year. Of this, 146,559 ft. was wildcat footage. The total initial production of the oil wells completed was 6362 bbl. and of the gas wells was 2,562,000 cu. feet. Three tests in the old Trenton area were drilled into the Cambrian and reported nothing more than tar residue. A Devonian test was to be made in the Griffin field in the Wabash River but owing to the delay caused by Federal restrictions this test did not get started in 1943. It is expected to spud in March 1944. The new discoveries in 1943 were virtually all in the southwestern part of the state, and all, so far, one-well pools, except the North Owensville pool, in Gibson County. The latter was brought in during the month of February and by the end of the year nine wells were producing in the pool, with a reported initial yield of 1260 bbl. per day. By the end of the year it had a daily average production of 401 bbl. and an accumulated production of 39,129 bbl. The average gravity of the oil is reported to be 35.6. On the Ohio-Indiana state line, early in 1943, a new pool was opened up in the old Trenton area. The discovery well was on the Ohio side of the line. An offset well was completed on the Indiana side, with an initial yield of 64 bbl., and settled down to 5 bbl. per day. This well produced 1154 bbl. up to Dec. 31, 1943. There was no further development here, because of the Federal Conservation Order M-68, restricting drilling to one well on 40 acres. The development pattern usually followed in this area is one well to 5 acres. The E. Rogers field was extended by one pool (Table 4). Most of the development in the oil-field pools during the year took place in the Kirksville pool, in Gibson County, and the Caborn pool, in Posey County. The crude-oil production in 1943 was approximately 5,273,000 bbl., a decline of 29 per cent from the previous year. The Griffin field, of Gibson and Posey Counties,

Jan 1, 1944

A plan which has just been approved by President Wilson, by, the Secretary of the Navy, and the Naval Consulting Board, provides for the active cooperation of the Associated Advertising Clubs of the World with the 30,000 engineers who will soon undertake the task of making a card index survey of American industry, so that it may be prepared for national defense, if need comes. Herbert S. Houston, President of the Associated Clubs of the World comments on the plan. "Through the great power of advertising we expect-to arouse manufacturers, workingmen, businessmen, in fact the whole country, to the vital need of making industry the basic line of defense so that, if necessity arises, it can supply munitions quickly and abundantly. "This is not a war measure, but a peace measure. The militarist will support it and so will the pacifist, as well as the great body of Americans in between. So the slogan `national defense and international peace, has been adopted believing that the two causes will be best served by linking them together. "While the primary thing, of course, is service to the country, it is manifest that this work of the engineers will be of the greatest service to industry in times of peace. If industry is mobilized for defense, it will be placed on a basis of efficiency to meet the keen competition that will surely follow the present war." Howard E. Coffin, one of the leaders of the American automobile industry, in outlining the far-reaching plans of his committee, the Committee of Industrial Preparedness of the Naval Consulting Board, said: "At the outset I wish to emphasize the absolutely non-partisan nature of this work. I am not even familiar with the political affiliations of the great majority of the members of the Board or of my committee. In setting out to, mobilize the industrial resources of the United States, we are concerned only with the benefit to the nation, and to that end we have called into being an organization made up of the best technical and business brains of the country, and that organization will work along business lines with strictly business methods. I think it reasonable to say that this is a movement perhaps unique in the history of national governments, and one geared up to the highest standards of twentieth century efficiency. "It is vitally necessary that American industry be made aware of the part it must play in the national defense. Our whole conception of warfare has been changed almost overnight. Our military heads at Washington are largely, of course, graduates of the very best technical schools, have been taught the profession of fighting, and are masters of that profession. As members of the Naval Consulting Board, we are unable to tell these men how to do their work. But while these departmental heads have lived with military problems all their adult years, we on the other hand have slept and eaten and lived with the industrial problems of the country. The two questions are wholly distinct, and the masters of one cannot possibly be the masters of the other. We are confronted then with the necessity of interlocking these two vast elements of our national life into a great working organization for the national defense. It is that which we are about to do.

Jan 5, 1916

By N. F. Fiore, M. C. Mangalick

DISLOCATION damping in single crystals is orientation dependent.&apos; If dislocations are distributed uniformly over all the slip systems in a crystal, and if each dislocation contributes identically to the damping process, then a damping loss or decrement 6 arises. In fact, however, for a crystal of axial direction (hkl), dislocations on certain slip systems are oriented to make a larger contribution to the damping loss than are dislocations on other slip systems. Thus the measuring damping, 6 (hkl) is proportional to an orientation factor (hkl), which weights the ability of each slip system in the crystal to contribute to the total damping. If it is assumed that dislocations are distributed uniformly on all slip systems, then for a given orientation of an fcc crystal this factor is determined2,3 by the three nonzero elastic constants Cll, C12, and C44 and the density p. In this communication measured values of elastic constants for two Fe-18Cr-Ni alloys are reported, and the dislocation damping results on two different orientations of each alloy are analyzed for orientation dependence. Elastic constants were determined by measuring the ultrasonic velocities of one longitudinal and two shear waves in (110) direction of the fcc crystals.4 Variation of velocities with the change in orientation is very small for (110) orientation,3 and so this direction is ideal for orientation factor and comparative damping measurements. Experimental Procedures. The nominal compositions of the alloys studied are given in Table I. These alloys were vacuum-melted and vacuum-cast from high-purity materials at U.S. Steel Applied Research Laboratories. The single crystals were grown by the modified Bridgeman technique. The specimens were homogenized at 1350°C for 20 hr, cut to shape and size with a spark cutter, and then annealed at 1100°C for 20 hr prior to use. In the KHz frequency range, the Marx composite piezoelectric oscillator was used to obtain the damping. The ultrasonic pulse technique was used to measure the ultrasonic velocities and the attenuation in the MHz frequency range. M.c.mANGALICK,-- StudentMemberAIME,formerly Research Assistant, University of Notre Dame, is now with Casting Laboratory, Chase Brass and Copper Co., Cleveland, Ohio. N. F. FIORE, Associate Member AIME, is Assistant Professor, Department of Metallurgical Engineering and Materials Science. University of Notre Dame, Notre Dame, Ind. This communication is part of a Ph.D. thesis presented by M. C. MANGALICK to the Graduate School of the University of Notre Dame. Manuscript submitted May 20. 1968. IMD Elastic Constants. Table I gives the values of the ultrasonic velocities. Values of C11, C12, and C44 calculated from these velocities are also given in Table I, and it is evident that there is very little variation in C11, C12, and C44 with nickel content. This slight variation may be attributed to inaccuracies in velocity measurements and practical differences in the orientations of the specimens. For example, in B the time interval for vl was 2.4 ± 0.05 sec giving an error in v1 of 0.235 x or 0.005 in. per sec. The elastic constants obtained by pulse technique were tested by calculating E<110>, Young&apos;s modulus for the (110) direction, from the equation: This value was compared with the value computed from the resonance bar measurements in which where fr is the resonance frequency and I, is the length of the specimen. In all cases, the values calculated from the ultrasonic velocity measurements

Jan 1, 1969

By H. W. R. Wardlaw

This paper shows how the cost of the drilling operation per 100-ft drilled can be related directly to bit weight, rotary speed and hydraulic horsepower variations. This enables optimum drilling conditions to be determined in a rapid and concise manner. The paper also shows how data for such calculations cun be obtained quickly and accurately by the "drill-off" method suggested by Lubinski. Examples are given to illustrate the principles and methods used. INTRODUCTION The problem of drilling oil wells at lowest cost and hazard needs little introduction, since it has been with us virtually from the earliest days of our industry. With better understanding of the effect of the various factors of bit weight, rotary speed and hydraulic jet action, however, the problem has recently taken on a more scientific aspect, and engineers or groups of engineers have been assigned to study many of the facets of this problem not immediately apparent to the general observer. Moreover, the availability of better equipment and materials has enabled certain practices to be adopted which were hitherto impractical or uneconomic. This has paved the way for further efforts to reduce footage costs, and so on. The improvements to be made in drilling technology and cost reduction are by no means exhausted, and we still frequently hear of new records being set and new materials and equipment becoming available. Some of the analytical methods used by the author to assist in promoting faster and more economic methods of drilling, particularly in Venezuela, form the basis for this descriptive study. STATEMENT OF THEORY AND DEFINITIONS In a highly competitive industry, it is no longer permissible to regard penetration rate as the sole criterion for drilling efficiency. Every new technique, however spectacular, must nowadays be viewed in the cold light of whether it will eventually lead to lower cost per foot drilled. In the exposition which follows, therefore, actual drilling rates will play only a secondary role, and attention will be focused on the more important aspect of cost per foot drilled. Changes in drilling factors such as weight and rotary speed will be studied in the light of how they directly affect the cost of operations. The advantage of this method is twofold—(1) cost increments are indicated directly; and (2) the relationships are, surprisingly enough, simpler than those relating to drilling rates. To achieve these advantages, it is necessary to introduce a new unit of measurement which, although unfamiliar, is readily understood. The unit in question will be referred to as the "actual drilling cost factor" and will be designated by the symbol h. The unit is defined as the number of rotating hours taken to penetrate 100 ft of formation. The unit can be obtained immediately from the actual drilling rate (r) in feet per hour; thus, This latter transformation is so easily effected that it may be convenient to use h as an international symbol for drilling cost, and to delay conversion to dollars, bolivars, pounds, etc, per foot until actually required (e.g., for fiscal reasons, etc.). In actual operations, h was found to vary in a relatively simple manner with increases in bit weight. The variation in h with rotary speed was found to be somewhat more complex. However, this also could be enormously simplified by introducing a further factor known as L or relative bit life. The factor L is also defined very simply by dividing 1,000 by the rotary speed (N) in revolutions per minute.

By E. Hein, R. A. Dodd

The fatigue softening of prior strain-hardened poly crystalline copper has been determined by measuring changes inflow stress resulting from fatigue treatments. Tensile fatigue does not soften the metal, while the softening due to reversed stress fatigue depends on the extent to which fully reversed stressing is approached. True tensile fatigue is shown to be possible only in the case of long wire specimens. Annealing following fatiguing of strain-hardened metal shows that tensile fatigue is very effective in modifying normal recovery and recrys-tallization. OBSERVATIONS by Ludwik and Scheu,&apos; Kenyon,&apos; Polakowski and Palchoudhuri, Kemsley, and Broom and Ham,596 have shown beyond doubt that strain-hardened metals are softened by reversed-stress fatigue. To some extent the softening might be associated with a rearrangement of dislocations, but the results of Broom and Ham5 on the temperature dependency of the fatigue hardening of annealed copper, and those of McCammon and Rosenberg7 on the partial recovery at 100&apos;C of fatigue-hardened copper suggest that point defects may be involved. Since lattice vacancies are the only species of point defect present in appreciable quantities in thermody-namic equilibrium, most attention has been accorded them in the various theories advanced to explain hardening and softening effects resulting from fatigue. Precise mechanisms remain uncertain, and while some effects may be due to single vacancies, defects arising from vacancy clusters may also contribute to the changes in properties. All types of plastic deformation result in point-defect formation, one frequently invoked formation mechanism involving the nonconservative motion of jogs formed by the intersection of, for example, mixed dislocations. But since fatigue deformation is thought to be a particularly effective way of forming point defects, additional mechanisms peculiar to fatigue must be sought. One possibility is that jogged loops contract during the unloading cycle to give rows of vacancies. A local high-vacancy concentration could conceivably promote polygonization and recovery by climb, and, therefore, could explain the fatigue softening of strain-hardened metals under appropriate conditions of temperature. Conversely, the experiments by Broom and Ham6 on the fatigue hardening of copper single crystals involving subsequent tensile testing of previously fatigued specimens, resulted in the observation of distinctly lowered yield points. This could be due to vacancy atmospheres associated with dislocations, possibly augmented by jogs on dislocations. In addition to the yield-point phenomenon, a post-yield hardening was observed, with a temperature-dependence resembling the friction-hardening of irradiated metals,9 this again suggesting a point-defect mechanism. An important development in this field has been the observation,10 by transmission electron microscopy, of high concentrations of prismatic loops in fatigued aluminum. By analogy with quenched aluminum filmso11 it seems certain that these loops originate in the collapse of vacancy clusters formed during deformation. Metals, such as copper, having a relatively low-stacking fault energy would tend to produce Frank sessile loops (in practice tetrahedral defects with stacking faults on all (111) planes) rather than the glissile prismatic loops observed in aluminum. The manner in which these various defects affect the different aspects of fatigue behavior has not yet been fully investigated. The present work was designed principally to indicate whether tensile fatigue gives rise to hardening and softening effects similar to those associated with reversed stress fatigue, and with the hope of providing additional information on the contribution of point defects to fatigue deformation. Despite the uncertain ty often associated with the interpretation of resistivity data, i.e., the relative contribution of stacking faults and other defects, such measurements are conveniently employed to study point defect pheno-

Jan 1, 1962

By F. H. Wilson, E. W. Palmer

The solid solubility of iron in 2 to 10 pct cupro-nickels increases with temperature and nickel content. Property changes accompanying various heat treatments indicate typical precipitation hardening behavior. Iron content also affects softening temperature and sub-scale formation. These factors, as well as impingement corrosion resistance, influence the optimum iron content of commercial alloys. FOR many years Cu-Ni alloys have been used extensively in the form of tubes, pipes, and plates for the construction of salt-water lines and surface condensers on shipboard and in tidewater power stations. The 30 pct Ni alloy has been considered more resistant to rapidly flowing sea water than alloys of lower nickel content, and has been standard on ships of the U. S. Navy. Some ten years ago, the still better corrosion resistance obtained by modifying the 30 pct Ni alloy with approximately 0.5 pct Fe was recognized, and the iron-bearing alloy rapidly superseded the plain alloy as the standard material for severe service. In 1945, Tracy and Hungerford1 published a study of the effect of iron on the corrosion of various cupro-nickels in sea-salt solutions, and their data indicated that the 10 pct Ni alloy containing about 0.75 pct Fe was equivalent to the 30 pct Ni alloy containing 0.5 pct Fe. This was confirmed by LaQue in discussion of the above paper, and by results in an experimental condenser set up at the Kure Beach marine test station of The International Nickel Co., reported by Freeman and Tracy.&apos; The 10 pct Ni iron-bearing alloy is now being very widely used in applications where the 30 pct Ni iron-bearing alloy was formerly considered standard. While this "substitution" has undoubtedly been stimulated by the present extreme shortage of nickel, it must be emphasized that it involves no loss of service performance, and would have occurred anyway in the course of time, for economic reasons. In view of the increasing use of the 10 pct alloy, it seems desirable to make generally available the results of several investigations of Cu-Ni-Fe alloys carried out in the Metallurgical Research Laboratory of The American Brass Co. in recent years. The present paper, deals with the constitution of these alloys in the copper-rich corner of the system, and with the variations in hardness and tensile properties resulting from the heat treatment of alloys containing various amounts of iron. Most of this work is concerned with alloys containing 10 pct Ni. With over about 0.75 pct fe, the 10 pct Ni alloy is suscep- Alloys Several series of cupro-nickel alloys containing iron were used in these investigations. Most of them were prepared in the laboratory, but two samples of commercially fabricated alloys were included. Series A—Nominally 2 and 5 pct Ni, each with 0 to 1.5 pct Fe. Series B—Nominally 10 pct Ni with 0.1 to 0.4 pct Fe. Series C—Nominally 1.0 pct Ni with 0 to 2 pct Fe. Series D—Nominally 10 pct Ni with 3 to 5 pct Fe. Series E—Nominally 10 pct Ni with 1 and 1.5 pct Fe.

Jan 1, 1953

By B. Lustman

IT has been known for a number of years that the addition of certain alkaline-earth and rare-earth metals to nickel-chromium base electric resistance alloys causes marked increase in their oxidation resistance as measured in an intermittent oxidation test similar to the ASTM—B 76-39 test. However, the mechanism whereby such additions confer protection is still unknown. On the basis of the experimental observation that the increase in life in intermittent tests of nickel-base alloys is proportional to the atomic radius of the added element, Hessen-bruchl has proposed that the added metal ions occupy holes in the oxide lattice which prevent diffusion of nickel ions in the oxide. Horn2 has postulated that the effect of such additions is to accelerate the rate of diffusion of chromium atoms in the metal and thus to favor the formation of Cr2O3 scales. Hickman and Gulbransen3 concluded from electron diffraction observation that the addition of the elements in question results in the formation of a barrier to the diffusion of nickel ions to the surface. In connection with some experiments conducted to develop a test for the resistance to oxidation of alloys in massive form under conditions of intermittent heating and cooling, some features of the oxidation of nickel-chromium base alloys were revealed which may serve to elucidate the mechanism of protection conferred by rare-earth and alkaline-earth elements. Specimens of cylindrical shape 0.360 in. diam x 0.37 in. long were placed in alumina thimbles and inserted into and withdrawn from a Globar-heated furnace operating at 2150°F at 7.5-min intervals. The weight of oxygen absorbed as well as the weight of oxide spalled were measured at intervals. With the particular experimental conditions used, the specimens in a 7.5-min cycle were at temperature for 2 min which corresponds to the heating time of the ASTM test. The weight changes of similar specimens under conditions of continuous heating in air at 2150°F were also measured. The specimens after oxidation were examined metal- lographically and samples of the spalled oxide collected for X-ray diffraction identification of the phases. The specimens used were from the same lot of material used by Hickman and Gulbransen3 and had the compositions shown in table 1. Included in table I are results of ASTM life tests on the materials in the form of wires. These materials, their composition and the ASTM life test data thereon were all supplied by F. E. Bash of the Driver-Harris Co. It may be noted that alloy 13246 of 80 pct nickel, 20 pct chromium nominal composition showed the shortest life in the ASTM test; alloy 12246 with the addition of small amounts of the elements zirconium, calcium, and aluminum, intermediate life; and alloy 12046 with the further addition of silicon, the longest life. In fig. 1 are shown the results of intermittent oxidation tests made on bulk specimens at 2150°F as well as continuous tests conducted at the same temperature. Duplicate tests were made on each specimen. The ordinate scale, inches of metal oxidized, was derived from the experimentally observed weight gain of oxygen by assuming the scale to be entirely Cr2O3. It may be noted that the metal-loss curves during intermittent oxidation show a constant or continuously increasing rate of weight

Jan 1, 1951

By B. Ramaswami, U. F. Kocks, B. Chalmers

This paper describes the tempetrature, solute (gold), and orientalion dependence of the plastic rleforlirnlion of silver single crystals. The virgin flow stress, To, and its temperatutre dependence incrense with increase in solute concentration. el decreases with decrease in temperature below room teiirperature and with increase in solute coucentralion. The dependence of 011 on temperature arid solute sontenl is due to the dependence of Ts on the two variables. An increase in ts, due to either the temperature or the solute conlent, results in a decrease of e11 in crystals of single-slip orientation and an increase of 011 in crystals of&apos; (100) find (111) orientation. is orientation-dependent and at all the temperatures and in all the materials studied. The Leveling off of the engineering stress-strain curve in crystals of (100) 07-ientotion at a stress tl, is associated with extensive cross slib. The temperature and strain -rate dependence of tl are similar to those of indicating that a rate process is the cause 01 this phenomenon. The plastic deformation of silrer crystals of (110) orientation is multiple to that of crystals of single-slip orientation. THE work hardening of fcc crystals has been the subject of intensive investigations in the past 15 years. The effect of orientation, deformation temperature, solutes, second phase or precipitates, strain rate, etc., has been studied in a number of fcc metals.&apos;-5 In spite of the considerable amount of work reported on the dependence of work hardening on the orientation, temperature, and solute concentration, certain aspects of the plastic deformation of fcc crystals have not been clarified. For instance, with the exception of a few investigations,6-8 where crystals of multiple-slip orientations have been studied, almost all the studies have been on crystals of single-slip orientations. Hence, a major portion of this study has been devoted to the dependence of plastic deformation on the multiplicity of slip systems and the enhanced possibility of dislocation interactions resulting from such multiplicity. Further, the abnormally low rate of work hardening observed at large strains at certain temperatures in crystals of the (100) orienta-tion 6-8has not been explained satisfactorily. It is the aim of this study to clarify this aspect of the orientation and temperature dependence of the plastic deformation of fcc single crystals. The work-hardening characteristics of single crystals of aluminum of ( 110) orientation have been studied at room temperatur "&apos;12 and above." They have not been studied at temperatures where the virgin flow stress is dependent on temperature or where, in Seeger&apos;s terminology is important. The work hardening of single crystals of (110) orientation is of interest for another reason. As shown in Table I, the dislocation reactions that are possible in the (110) orientation are similar in certain respects to those that are possible in the (100) orientation. Hence, the deformation of single crystals of silver of (110) orientation was studied in the temperature range 100° to 900°K at intervals of 200°K. The effect of solute concentration on the plastic deformation of fcc single crystals of single-slip orientation has been studied by several investiaators.> In all of these investigations—with the exception of Ref. 20—single crystals of identical orientation have not been used, with the result that the orientation dependence of plastic deformation is superimposed on the effect of the solute. In addition, the effect of the solute on the work-hardening characteristics of single crystals of multiple-slip orientations has not been studied by the previous

Jan 1, 1965

By D. Mills, G. B. Craig

The defortnaliotz of zirconicltt single crystals conlaining osygen in the range 740 to 6800 atom parts per nilllion was esanined oc7er the range 77" to 950°K. An anctlsis of the dqfarmaliotz parameters leads to the cotcllsiotr that the rale -cotzfrolling thermally activated dqivr,irrtion process oe-r /he range 77" to 560°K is oc.crco,ling osvgen alotns. A thermally actitaled defor,ilntion process is not found between 600" and 800", but does occur aboz%e 800°K. THE present investigation was undertaken to measure the effects of controlled amounts of oxygen on the deformation parameters of a zirconium single crystals over the temperature range 77" to 950°K and to determine the rate-controlling mechanisms. Although there is no doubt that the mechanical properties of the group IV metals, titanium, zirconium, and hafnium, are strongly influenced by the interstitial impurities oxygen, nitrogen, carbon, and hydrogen, there are many conflicting theories as to the role played by the interstitials during the deformation proess.&apos;- There is general agreement that the mechanisms which control plastic flow in a metal impose characteristic values on such parameters as the flow stress and its temperature dependence, the activation volume, and the activation energies. These parameters will be used to analyze the deformation mechanisms. eltham,&apos; Sargent,16 and ibbs&apos; have shown that the stress relaxation technique allows the activation volume characteristic of the deformation process to be found during the course of a simple tension test. In many cases it is found that the relaxation of stress is logarithmic with time and obeys a relationship of the following form: T-T = AT =S logl0(qt + C) [I] where t, is the shear stress at the start of the relaxation test, t is the shear stress at time t, and S. q, and C are experimental constants, and S is the strain rate sensitivity of the stress t as shown in the appendix. The slope found from a semilogarithmic plot of At vs time is approximately equal to S. The activation volume u, association with the deformation process, is found from the following relationship: The theoretical treatment of thermally activated plastic flow due to schoeck18 shows that the activation volume when combined with the temperature dependence of the flow stress gives the activation energy for the process according to equations: seegerZ3 considers that the flow stress at lower temperatures ld is composed of two parts such that Tapplied = tinternal + Teffective , where Teffective 3 ff , is the stress necessary to overcome the local obstacles to deformation and Tinternal, ri, is the stress necessary to overcome the long-range elastic stress field of dislocations on other planes. ri is considered to be largely elastic in origin and can be estimated from the stress value at the temperature independent portion of the flow stress-temperature curve. EXPERIMENTAL The crystal bar zirconium used in this investigation was supplied by Wah Chang Corp. whose certified analysis gave the following impurity contents in parts per million by weight: oxygen, 150; nitrogen, 10; iron, 180. All others were less than 100 ppm. The oxygen and iron contents were confirmed by neutron activation and chemical analyses, respectively. Single crystals were grown in an electron beam furnace according to the method of Wilson and Pickle-simer&apos;&apos; and ills.&apos;&apos; The orientation of the crystals was such that the specimen axes were located in the lower third of the standard section of the basal plane stereographic projection for zirconium. This orienta-

Jan 1, 1969

By S. C. Sircar, D. R. Wiles

The rate has been studied of the hydrogen reduction of nickel ions in acetate -buffered solutions, using a nickel catalyst. At temperatures between 130°and 160°C, the rate is found to be proportional to the catalyst area, the nickel ion concentration, and the hydrogen pressure. The effect of hydrogen ions is to reduce the observed rate, likely by causing the reverse reaction (dissolution) to proceed. The experimental activation energy was found to be 25 kcal per mole. THE precipitation of metals and lower oxides from solution by hydrogen reduction has been quite actively investigated during the past few years.1 In the case of nickel, the kinetics of the precipitation have been studied in ammonia solution2 but extension of this study to acid solutions has not attracted much interest, largely because of the unfavorable thermodynamics at all but the lowest acidities. For example, Schaufelberger foundg that only 10 pct reduction of nickel could be effected in sulphate solutions. One kinetic study of the reduction of Ni++ has been reported by Knacke, Pawlek, and Sussmuth,4 in which the order of the reaction was found to be one in nickel ion and one-half in hydrogen pressure. No mention was made as to the part played by the nickel catalyst, or by the pH of the solution. Moreover, the activation energy reported (4 .12 kcal per mole) is so low as to lead to some question as to whether diffusion might be playing a major role in determining the kinetics. We have recently completed a study5 of the kinetics of the hydrogen precipitation of nickel from acetate-buffered acidic solutions whose results confirm and amplify those of Knacke et al. EXPERIMENTAL PROCEDURES The work was done in a high-pressure autoclavee by the usual technique of removing small samples of the solution for analysis. Nickel analysis was done colorimetrically by the dimethylglyoxime method.&apos; The catalyst used was carbonyl nickel powder (Standard A powder of the Mond Nickel Co., Ltd.) which was found to be composed of spheres of less than 350 mesh. The surface area of the powder was determined in this laboratory by the B. E. T. method to be 1.85 sq m (m2) per g. The catalyst was added to the solution only after the proper temperature and pressure had been reached. Agitation of the baffled system was by a turbine-type impeller, rotated at speeds between 400 and 750 rpm. The reduction rate was found to be independent of the stirring rate, so it was assumed that diffusion in the liquid does not limit the rate. In typical experiments, the nickel concentration was unchanged during an induction period of variable length. The concentration then decreased sharply, and gradually levelled off to approach the final equilibrium value. In some cases, notably at high stirring rates, the nickel concentration was found to increase considerably during the induction period, and then to decrease. In all cases, the rate was determined from the slope of the tangent to the rate curve as the concentration first decreased below the initial value. This is seen in Fig. 1. The rate measurements were found to be reproducible to within about 5 and to be quite independent of the nature or duration of the induction period. The range of conditions used is given in Table I.

Jan 1, 1961

By Gareth Thomas

The analysis of Kikuchi pattersns of exct ovientalions from single cryslals and paired Kikuchi lines from single and overlapping crystals is shown to be useful and quanlitalve and is applied to Phase transfovnzcitions including ordering, spinodals, mavten-silic, and nuclealion and growth pyocesses. 112 pinciple, the analysis of exacl orientations enables the crystal system and the Bravais lattice of a crystal to he determined. The advantages of the davk-field imaging technigure for detecting vevy small precipitates are also described. ALTHOUGH Kikuchi electron-diffraction patterns were first observed nearly 40 years ago,&apos; little systematic application seems to have been made of them, until fairly recently during electron microscopy, when their usefulness in contrast experimen and for determining exact orientations8&apos;9 has been pointed out. With the availability of gonio-metric specimen tilting stages it has now become possible to make much wider use of diffraction patterns, particularly the Kikuchi pattern, which is the main subject of this paper. The treatment presented here is not exhaustive but it is hoped that it will stimulate more use of Kikuchi patterns during electron-microscopy investigations. The Kikuchi pattern is formed as a result of Bragg diffraction of the inelastically scattered electrons produced during the interaction of the beam and thick specimens, The important feature of these patterns is that they give an accurate representation of the symmetry of the crystal being investigated, so that it is possible to identify crystal systems and even the Bravais lattice. This means that new structures, e.g., formed in phase transformations, may be identified during normal electron microscopy, so that Kikuchi-pattern analyses considerably extend the uses of the electron microscope. Recent work has also shown that dark-field images are more informative than bright-field images, particularly, for observing small precipitates. The second part of this paper discusses some applications and advantages of dark-field imaging in studies of two-phase systems. 1) DIFFRACTION PATTERNS 1.1) Spot Patterns. Electron-diffraction spot patterns have their limitations because of the importance of the form factor on the intensities and shape of the reciprocal lattice points. Because of the extension of these points into relrods, reflections are possible over a large angular range (+5 deg) and the patterns from thin regions can be complicated because second-layer relrods intersect the reflecting sphere. Spot patterns can thus give only an approximate idea of the crystallography unless the foil is tilted into exact orientation. In this case the spot pattern is symmetrical, with equal numbers of spots on the positive and negative zone directions about the origin. Such cases are necessary for structural analyses and have been used recently to determine the crystal structure of the ordered Ta64C phase." Exact orientation means that the plane of the reciprocal lattice lies exactly normal to the incident beam as shown in Fig. 1(b). It should be noted that in exact orientations the angle of reflection is less than the exact Bragg angle 9 so that the reciprocal lattice points lie to the outside of the sphere, Fig. 1(b). This deviation is denoted by the parameter s and in the usual convention4 s is negative for exact orientations and, of course, zero at the exact reflecting position shown in Fig. l(a). In order to avoid secondary reflections from thickness relrods it is advantageous to work in thicker regions of foils. Diffraction from thick regions may also produce Kikuchi patterns and as dis-

Jan 1, 1965

By C. R. Clark, G. Swift, D. S. Roberts

The purpose of this investigation was to measure PVT behavior of various types and combinations of heavy hydrocarbon components from the paraffinic, naphthenic and aromatic classes where the relative proportions Of the various components were selected to approximate those of natural gas or gas condensate systems. Synthetic mixtures were used so that the compositions Of the various components could be measured accurately. n-Heptane, methylcyclohexane and methylbenzene were used to represent the paraffinic, naphthenic and aromatic components of the heavy fraction. In the mixtures studied, the heavy fraction composition was held constant at O. O5-mole lraction, the balance being methane except for one mixture where 0.10-mo1e fraction of an intermediate component, propane, was added. The PVT data for the mixtures were determined in a variable-volume, constant-mass apparatus at psuedo-reducedtemperatures from 1.84 to 2.00, over a pseudo-reduced pressure range from 2.3 to 12.0. The experimental results showed that, regardless of the type of heavy material (paraffinic, naphthenic, aromatic, or combinations thereof) mixed with methane or methane and propane, the compressibility factors at equal values of pseudo-reduced temperature and pressure varied by less than 2.2 percent. INTRODUCTION PVT data is used for natural gas and gas condensate fluids in determining reserves of reservoirs and performance of wells, in metering produced fluids, and in recombining samples for laboratory studies. While there are vast amounts of PVT data reported for natural gas and gas condensate systems from which useful correlations have been developed, &apos; the compositional analyses for these systems and the resultant correlations typically were made with components analyzed through some arbitrary carbon number, usually C6, with the residue reported as a lumped "heavy" fraction. The heavy fraction was stoichiometrically recombined on the basis of an apparent molecular weight to give the final compositional analysis. It is virtually impossible to make a systematic analysis of the effect that variation of the relative amounts of paraffinic, naphthenic and aromatic constituents of the heavy fraction of natural systems might have on PVT behavior. Because there is considerable latitude in the relative amounts of these constituents, one speaks of crudes or condensate liquids as being "paraffin base", etc. It is of interest to determine if changes in the relative amounts of these three types of hydrocarbons in the heavy fraction cause significant changes in PVT behavior. If so, steps should be taken to describe better the nature of the heavy fraction in PVT correlations. If not, more confidence can be placed in the correlations presently employed. DESIGN OF THE EXPERIMENTAL INVESTIGATION We attempted to determine if changes in the base of the heavy fraction would cause significant changes in the PVT behavior of gas or gas condensate fluids. Synthetic mixtures were used to enable us to systematically vary the base of the heavy fraction and to analyze accurately the fluids. We found that the heavy fraction of naturally occurring condensate systems seldom exceeds 0.05-mole fraction. Thus, the mole fraction of the heavy fraction in the synthetic systems studied was set arbitrarily at 0.05, to maximize whatever deviations in PVT behavior that might occur. Further, we judged that since the C7 hydrocarbons normally are present in greater quantities than higher carbon number hydrocarbons in naturally occurring systems, the use of n-heptane, methyl cyclohexane, and methylbenzene to represent the paraffinic, naphthenic, and aromatic species in the heavy fraction would be most appropriate. Finally, to enable us to compare our

Jan 1, 1970

By P. F. Gnirk, J. B. Cheatham

Single bit-tooth penetration experiments under static load were conducted on six rocks at confining pressures of O to 5,000 psi using sharp wedge-shaped teeth with included angles ranging from 30 to 120° In general, the force-displacement curves for all rocks exhibit an increasingly nonlinear and discontinuous behavior with decreasing confining pressure. The confining pressure at which a rock exhibits a macroscopic transition from predominantly ductile to predominantly brittle behavior during penetration vmies from about 500 to 1,000 psi for the limestones to greater than 5,000 psi for dolomite. The correlation between calculated values of force per unit penetration based on plasticity theory and experimental values is quite encouraging, even at confining pressures as low as 1,000 psi A qualitative correlation between volume of fragmented rock per unit energy input for a single bit-tooth and drilling rate for microbits appears to exist over a confining pressure range of 0 to 5,000 psi. INTRODUCTION Laboratory experiments utilizing a small-scale drilling apparatus have demonstrated that penetration rates are reduced considerably as a result of increasing the confining pressure from atmospheric to a few thousand psi?-3 This undesirable situation can, in general, be attributed to a combination of decreased efficiency of chip removal at the bottom of the borehole, increased rock-failure strength, and a possible change in the mechanism of chip generation and rock fragmentation with increasing confining pressure. To more fully understand the principles underlying the last circumstance, it is the purpose of this investigation to experimentally study the mechanism of single bit-tooth penetration into dry rock at low confining pressures and, in particular, to establish the confining pressure at which the penetration mechanism may undergo a brittle to ductile transition for various rock types commonly encountered in drilling. Confining pressure as used here refers to the differential pressure between the borehole fluid pressure and the formation-pore fluid pressure. EXPERIMENTAL PROCEDURE Using an experimental apparatus previously described: a single, sharp wedge-shaped tool was forced under a "statically" applied load into an effectively semi-in finite dry rock sample subjected to a prescribed confining pressure. To prevent the invasion of the con fining-pressure fluid into the pores of the rock sample during penetration, the exposed surface of the rock was jacketed with a layer of silicon putty.* Electrical instrumentation incorporated into the apparatus yielded a graphical plot of force on the tool as a function of penetration or displacement of the tool into the rock during an experiment. During the course of the experimentation the following conditions were maintained constant: (1) pore pressure — atmospheric (i.e., the rock was dry); (2) temperature — 75F; (3) rate of loading — essentially static (approximately 0.002 in./sec); (4) bit tooth — a sharp wedge-shaped tool loaded normal to the rock surface; (5) rock surface — smooth and flat; (6) drilling fluid — hydraulic oil; and (7) maximum depth of penetration — approximateiy 0.1 in. In addition, each experiment was performed on a different rock sample so the rock surface is free of a layer of cuttings and of any previous indentation craters. The influence of the corners of a borehole was neglected, since each rock sample was cemented inta a section of aLuminum tubing to simulate a semi-infinite body. Indentation experiments were made on a sandstone, two limestones, a marble, a dolomite and a schist with a 60&apos; bit-tooth over a range of confining pressures from atmospheric to 5,000 psi and at a constant confining pressure of 1,000 psi for a variety of bit-teeth with angles ranging from 30 to

Jan 1, 1966

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:&apos;5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

By C. G. Dunn

The measurement of interfacial teusions or grain boundary energies in metals is an important metallurgical problem, especially since it bears on growth and nucleation processes. Statistical methods of measuring equilibrium grain boundary angles, which relate interfacial tensions, have been used by some investigators1&apos;2 but more direct methods would be preferred. A direct way, based on a simple extension of a successful method of growing single crystals of silicon ferrite to predetermined orientations in flat specimens,3 is to produce three-grain specimens in such a way that the equilibrium common grain boundary will be perpendicular to the surface of the specimen. The angles to be measured then appear as the grain boundary angles in the surface of the specimen. The method of producing a single crystal specimen with a predetermined orientation is basically the same as that employed by Yoshida and Fuji-wara4 in their work on aluminum wires. The specimen, prior to any single crystal transformation, must have a matrix which will support the growth of a crystal of the desired orientation. Growth may occur through exaggerated grain growth or, if the matrix is strained a critical amount. by normal recrystallization. In either case the matrix must have stability at the temperature used to effect the transformation, this stability appearing as a long induction period for exaggerated grain growth or for the formation of recrystallization nuclei. Additional control is gained by using a high temperature gradient through which the specimen is moved at a suitable rate. To obtain the desired orientation, the specimen is fed a short way into the furnace producing one or more crystals in the hot end. After the specimen is removed from the furnace, the orientation of a crystal is determined, so that this crystal may be reoriented by properly deforming a narrow piece of the matrix between the end crystal and the rest of the specimen. This part of the specimen in the case of silicon ferrite is preferably held at red heat during the reorienting process. Fig 1 shows a specimen which is ready to be transformed into a single crystal through growth of a reoriented "seed" crystal. When the method just described is applied to the production of a three-grain specimen two crystals are grown first side by side in one end, the specimen is then reversed and the third grain grown from the opposite end. A suitable group of grains each of different orientation is one where all three grains have the same crystallo-graphic plane in the plane of the specimen. Fig 2 shows a photograph of a three-grain group prepared as described. The notches are introduced in the open ends of the grain boundaries to anchor them during the final annealing operations which ultimately should bring the grain boundaries to the lowest energy configuration. Two-grain groups with different crystallographic planes in the plane of the specimen can be similarly prepared and treated. If the two grains have different surface (gas to metal) energies per unit area, the equilibrium condition leads to a curved grain boundary.* * This feature of the problem was pointed out by J. c. Fisher. References 1. Cyril Stanley Smith: Grains. Phases and Interfaces: An Interpretation of Microstructure. Trans. AIME 175, 15. Met. Tech. TP 2387, June 1948. 2. D. Harker and E. Parker: Grain Shape and Grain Growth. Trans. A.S.M. (194,5) 34, 156-195. 3. C. G. Dunn, A. Seddon, and R. Wylie: Unpublished Work, 1946-1947. 4. Takeo Fujiwara: A Method of Producing A Long Single-Crystal Wire of Aluminum with any Desired Crystallographic Axis. Jnl. of Sci. Horoshima Univ. A, (1939) 9, No. 3, 227.

Jan 1, 1950

By D. J. Freeh, W. E. Horst, R. C. Kellner

This paper is concerned with the description of grinding characteristics in a batch grinding system. A mathematical model was developed and used for simulating the system on an analog computer. A general equation describing the change of selected size fractions with respect to time is presented. The empirical verification of the model is discussed. In order to understand the performance of a grinding system, it would be desirable to have a mathematical description of the system&apos;s behavior. The development of a mathematical model to describe the performance of a batch dry-grinding operation was investigated. This is the first step toward reaching the objective of a practical mathematical description of a grinding system that could be employed for process control and optimization of a simple or complex grinding circuit. Although this article is concerned only with batch grinding performance, experimental work is being conducted to extend the model to continuous grinding systems. BASIC PROCESS CONSIDERATIONS In a paper dealing with the probability theory of wet ball milling, Roberts1 correlated the rate of change of oversize material, C, with energy input, E, as follows where the energy input is expressed in power/unit mass and k is a constant for each particle size. Experimental grinding studies were made by Bowdish2 to extend the previous work of Roberts. The work of Bowdish also showed that the rate of breaking of oversize particles in a ball mill is proportional to the concentration of oversize particles present. He further demonstrated that breaking of oversize particles is proportional to the surface area of the balls used for grinding. Rate equations were presented and it was concluded that grinding could be considered as a first order phenomenon according to the rate equation [2] di which is in accordance with Eq. 1. In Eq. 2, the effect of ball area is included in the constant k,. Other rate equations were reported to show the effect of a change in ball area and removal of fines during grinding. Correlation studies made by Arbiter and BhranY indicate a first-order rate equation for quartz; however, their data showed less than first-order rates existed for some of the other materials evaluated. More recently Kelsall4 has shown that the rate of breakage of any narrow size range of quartz could be described by a first-order rate equation. Several other investigators5-7 have described grinding behavior in terms of rate equations or kinetics. In general, the rate equations have been described for each particle size; however, the interactions between sizes and the overall relationships that exist have not been considered, at least not in the form of solving a group of simultaneous differential equations. Extensive work has been conducted by various investigators using a probabilistic approach which has expanded stein&apos;s&apos; earlier work. Selection and breakage matrices are incorporated in the probabilistic model as contrasted with the deterministic method presented here. A batch grinding operation may be considered as an unsteady-state process from the standpoint that the conditions within the mill are a function of time. Therefore, a plot of mass fraction of the i-th size versus time would give a set of curves as shown in Fig. 1. In these curves X , represents the mass fraction of large size material, X2 intermediate size, and X3 small size material. An examination of these curves shows a strong similarity to the curves that would be obtained from a chemical reaction of the type9 A?B?C, [3] where A would be comparable to the largest size material being broken to an intermediate size, 3, and

Jan 1, 1968

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By C. S. Matthews, P. Hazebroek, F. Brons

A method has been developed for calculating the average pressure in a bounded reservoir. The reservoir is first divided into the individual drainage volumes of each well, by using the criterion that at steady state each individual drainage volume is proportional to a well&apos;s production rate. The average pressure in each drainage volume is then calculated by a method developed in the report. By volumetrically averaging these individual drainage volume pressures, the average pressure in the entire reservoir is obtained. To calculate the average pressure in each drainage volume, a correction is applied to the ordinary extrapolated pressure, i.e., the pressure obtained by extrapolating to infinite time the linear portion of the graph of closed-in pressure versus log[?t/(t + ?t)], where At is the closed-in time and t the production time. The correction, which is a function of the production time, is presented in graphical form for different shapes of the drainage area (horizontal cross section of the drainage volume). INTRODUCTION It is important to be able to find the volumetric average pressure in a reservoir so that the size of the reservoir may be determined from material balance calculations. It is also desirable to be able to find the approximate distribution of pressure within a reservoir for detection of fluid movement. &apos;The purpose of this paper is to present a method for calculating both the average reservoir pressure and the approximate distribution of pressure within a bounded reservoir — that is, a reservoir with no water drive. In reservoirs where the pressure builds up rapidly after wells are shut in, the determination of average pressure generally poses little problem, for one often need only average the final buildup pressures. It is when pressure buildup is slow that difficulties arise. For practical and economical reasons, the time allowable for closing in wells is limited. If at the maximum allowable closed-in time the pressure has not reached a con- stant value (and this is more often the case than is generally realized), calculation of average pressure presents difficulties. One method which has been used in the past for obtaining an "average" pressure involves the extrapolation to infinite closed-in time of curves of pressure as a function of closed-in time. Contour maps of these extrapolated pressures are used in arriving at an average pressure. In some cases wells are shut in for arbitrary Lengths of time, and contours of these arbitrary shut-in pressures are used for calculation. All these methods are somewhat arbitrary and suffer from lack of fundamental theoretical basis. For example, no precise meaning can be given either to the extrapolated or to the arbitrary shut-in pressure. Furthermore, there seems to be no reason why either set of pressures should be contourable. It was because of the vagueness of these old methods and their lack of a sound theoretical basis that, the present method for determining average reservoir pressure was developed. SYMBOLS A = drainage area of a well, cm&apos; A, = drainage area of well j, cm2 A , = total drainage area of all wells in a reservoir, cm2 c = coefficient of compressibility of fluid at reservoir temperature, atm-1 f = hydrocarbin-filled porosity, fraction h = net thickness of formation, cm k = permeability of formation, darcy p = pressure at a well, atm p0 = initial reservoir pressure, atm p* = pressure obtained by straight-line extrapolation of linear portion of plot of p versus log [At/(t+ At)] p = volumetric average pressure inside drainage volume of a well q = volume flow rate at a well, cc/sec a: prevailing reservoir conditions q, = total volumetric flow rate from a reservoir, cc/sec at prevailing reservoir conditions rw = radius of well bore, cm T = kt/fµcA t = corrected time of production of a well, seconds, defined by

Jan 1, 1955