Search Documents

By H. M. Faust

THERE are a number of different types of power plants. Some use coal to generate steam, others use oil or gas either in the form of steam or internal combustion equipment, while still others avail themselves of water power as a source of energy. A general comparison of the relative power production with different sources of energy in the United States, for several different years is set up in Table 1. This table shows that coal was used to generate 85.6 per cent of the total heat power requirements of 1909, and only 59.2 per cent of the 1930 requirements. The increasing proportion of modern heat energy generated by the use of fuel other than coal is apparent. If coal is to maintain its importance as a source of heat energy, the necessity for its improved perform-ance, in which preparation plays an -important part, cannot be stressed too strongly.

Jan 1, 1933

By Thomas L. Garrard, James A. Sprague, Rex B. McLellan, Samuel J. Horowitz

A simple rnodel for interstitial solid solutions has been devised in which each solute atom interacts with the solzlent lattice in such a way as to exclude an integral number of nearest-neighbor sites from being occupied by solute atoms. The vemaining interstitial sites ave not affected. In calculating the entropy of such a solution the increase in the number of interstitial sites available to solute atoms due to the ozlerlap of blocked sites is taken into account. The ther-modynamic functions and the solute activity fov the solution rnodel are calculated. It is shown that considevation of the overlap sues vise to a correction term of the order 8' ( where 0 is the ratio of solute to solvent atoms) in the thevmodynamic functions of the solution and the solute activity. The theo,uetical equation for the solute activity was used to analyze the available data for the activity of carbon in austenite at three different temperatures. The use of a computer enabled many comparisons to be made between the experimental activity data and those predicted by both the complex blocking model and the simple, widely used blocking model in which the ozierlapping of blocked sites is not taken into consideration. Even though at the highest concentvations oj carbon the value of 0 is small it is shown that the best fit to the experimental data is found with the complex blocking model. RECENTLY it has been shown by analysis of gas-solid equilibriums that many interstitial solid solutions can be described by the quasi-regular solution model in which the partial energy of solution E, is independent of composition and, apart from a composition-independent term due to nonconfigurational factors, the partial entropy is that of an ideal solution. Dilute solutions of nitrogen in both bcc and fcc iron,' dilute solutions of oxygen and silver,' carbon in a Fe,' and dilute solutions of carbon in ? Fe2 are all quasi-regular. In addition many hydrogen-metal solutions, both dilute and concentrated (with the notable exceptions of the H-Ni and H-Pd systems), can be described by this model.3 However, it has been shown that, at various temperatures, solutions of carbon in ? Fe begin to depart strongly from quasi-regular behavior at low concentrations. A plot of the activity of carbon in ? Fe relative to pure graphite vs atom fraction of carbon (Cc) calculated from Smith's data4 begins to depart from the (nonlinear) plot for a quasi-regular solution at about Cc = 0.02. Several statistical models have been proposed to account for the thermodynamic behavior of carbon in y Fe. Darken and smith4 set up a model in which a carbon atom in its octahedral site in the fcc lattice has either one or no neighboring carbon atoms in the twelve nearest-neighbor octahedral sites. It is assumed that the number of carbon atoms having more than one nearest neighbor is negligibly small and that a solute atom does not interact with another solute atom located at a greater distance than the first shell of interstitial sites. Thus this model contains two characteristic interaction energies. Darken and Smith showed that this model gives reasonable agreement with the measured variation of carbon activity ac with composition. It is noteworthy that Darken and Smith concluded from their analysis of the activity data using this model that there was a repulsive force between carbon atoms in austenite which reduces the concentration of C-C pairs below that corresponding to random mixing. Recently Aaronson, Domian, and pound5 have considered in detail the statistical model developed by Lachere and by Fowler and Guggenheim7 and have shown that it is compatible with the activity data for carbon in austenite. In Darken's model the energy of solution of carbon in austenite is dependent on temperature and concentration; the departure from Henry's law arises from the concentration dependence of the energy of solution. In Aaronson, Domian, and Pound's discussion of the Lacher, Fowler, Guggenheim model the interaction energy wy between adjacent carbon atoms in austenite is strongly temperature-dependent. Aaronson et al . suggested that this temperature dependence of wy and hence the energy of solution of carbon could be explained either by the formation of clusters of carbon atoms (despite the repulsive nature of wy) or by the dual occupancy of the octahedral and tetrahedral sites by the carbon atoms. However, a temperature-dependent heat of solution

Jan 1, 1968

By M. G. Nicholas

The influence of deformation, relative movement and surface cleanliness on the strength of room -temperature "interparticle" bonds between copper surfaces has been studied. No bonding resulted when clean surfaces were merely pressed together, even under pressures of 50,000 psi. Bonding resulted, however, when clean surfaces were simultaneously pressed and moved relative to each other, some bonding occurring no matter how small the pressure or relative movement. Exposure of the clean surfaces to various chemicals inhibited bonding, none at all being produced by small relative movements. The size of the movements which first produce bonding between exposed surfaces depends on the nature of the chemical, being less than 0.002 in. for cleansing reagents and greater than 0.004 in. for lubricants, water and hydrogen sulfide. It is concluded from the experimental data that the prime requirement for bonding is the dispersal of surface films such as oxides and adsorbed contaminants. THE formation of interparticle bonds during the room-temperature compaction of powder metallurgy components greatly increases the ease of handling in subsequent production operations prior to sintering. The strength of unsintered compacts follows the same general trends as their density and hardness, but quantitative data are extremely Scarce. Quantitative correlation of the data on the overall strength of a compact with that of the individual interparticle bonds is virtually impossible due to the extremely complex geometry of powder compacts. Qualitatively, however, the strengths of unsintered compacts can be correlated with variations in parameters known to influence the extent of cold bonding, and hence interparticle bonding, such as surface cleanliness, relative movement, and deformation of the mating surfaces. Kuzmic and seelig4 found that contamination of powder particle surfaces with lubricants reduced the strength of unsintered iron and copper compacts. Interparticle shear has been shown to promote bonding by Train and Hersey7 while Gregory has shown that die rotation is beneficial. Eilender and schwalbe6 concluded that most bonding occurred during the early stages of pressing iron powder compacts when interparticle shear is one of the principal processes occurring. mile there can be little doubt that these and other factors, such as particle size and shape, affect the extent of interparticle bonding produced by compaction, evaluation of the influence of individual factors is not easy. Particle deformation and relative movement, for example, occur simultaneously during compaction, making any precise measurement of their relative influences difficult. Because of these and other difficulties encountered in studying interparticle bonding in actual powder compacts, the approach adopted in this study was to

Jan 1, 1963

1910, hundreds of thousands of dollars of work and equipment in a 1500-foot shaft, crosscuts and pumping had found only copper-lean pyrite in two cross- cuts, and nothing in a third. Going aimlessly along the third crosscut one day, after looking at the barren face I happened to notice a dark spot in the white limestone, near the floor on one side. I picked, and found it was a little triangle of rich chalcopyrite. Next day I took Bill Gohring, then mine superintendent, in to see it. He said nothing else had succeeded so we might as well try that. The new drift broke into a full face of high grade copper ore in the first round, and continued in rich ore for 2200 feel broken only by a couple of short stretches of lean pyrite. The earlier crosscuts had happened to cut these lean areas. Q: Was there any single thing that called your attention to that little dark spot in the side of the Briggs crosscut, rather than to any other discolored spot? Joralemon: Nothing very definite. Maybe luck, maybe that indefinable subconscious thinking that

Jan 9, 1964

By ir. H. Eraly

The allocation of miners to teams, and of teams to production faces, is complicated by the high degree of absenteism of miners in Belgium. Therefore, the exact knowledge of who is actually present at the beginning of a shift and of the exact skills of those present, enables the foremen and mine captains to constitute their teams before all men go down into the mine in the most effective way possible. This paper describes the system of attendance recording and of displays which the foremen use to constitute their teams and/or to interrogate the personnel data base in order to do so. It shows how the foremen dialogue with the computer, to change the function of a miner within a team, to another team, or the function of a team as a whole. The implementation of the system, data bases, and data communication equipment and procedures, is described. The benefits obtained are presented for each level of the company: foremen and team supervisors, engineers, mine management.

Jan 1, 1977

By J. S. Dodge, I. M. Krieger

The laminarturbulent transition was studied for monodisperse rigid polymer latices as functions of particle diameter and concentration at several tube diameters. Breaks in the graph of friction factor US Reynolds number were used to characterize the transition; rates of shear were sufficiently high so that Newtonian behavior at the high shear limiting viscosity could be assumed. No abnormal behavior was noted at concentrations below 30 volume percent. At higher concentrations, suppression of turbulence was observed with critical Reynolds numbers rising to as high as 5,500 at 50 volume percent. No definite effect on the transition was noted due to variation of particle size or tube diameter. The type of surfactant used to stabilize the latex was found to have an important influence on the critical Reynolds number. INTRODUCTION For some polymer solutions and solid-in-liquid suspensions, the transition from laminar behavior to turbulence in pipeline flow has been reported to take place at unusually low1-5 and in some cases at higher than normal6,7 critical Reynolds numbers. Extreme values of critical Reynolds numbers (NRe*) have been found to range from 1 to 6,000, as opposed to the values of 2,000 to 3,500 which are obtained for ordinary liquids. Observations have also been reported of drag reduction in fully developed turbulent flow, i.e., a decreased value of the friction factor in the Reynolds number-friction factor plot6*10-14 in colloidal and polymeric fluids. In some cases, turbulence suppression (unusually large values of Nre*) was noted to occur preceding the drag reduction,6 while a normal transition was noted in other cases of drag reduction.14 To relate the occurrence of turbulence suppression and drag reduction to the molecular or particulate structure of the fluid, it is desirable to characterize the structural variables with some precision. For most colloidal dispersions and polymeric fluids, this is very difficult; particle sizes, shapes and stiffnesses may vary over wide ranges in the same sample. Recently, however, a colloidal fluid has become available which consists of rigid spherical particles of highly uniform diameter dispersed in a simple Newtonian liquid. These are monodisperse polymer latices, prepared by carefully controlled emulsion polymerization reactions. The purpose of this research was to study the transition to turbulence in these well-characterized colloidal fluids as a function of concentration, particle diameter and tube diameter. Typical flow curves of latices of high solids content are shown in Fig. 1. While these curves were obtained with monodisperse latices, the general shape of the curve is also typical of a polydisperse latex. It is observed that a shear-thinning region occurs for low to moderate rates of shear. At sufficiently high shearing rates a limiting Newtonian viscosity is reached. The viscosity µ diminishes with decreasing volume fraction 4 at all shear rates. For 4 less than 0.25, latices are Newtonian at all rates of shear.15 An increase in average particle size (at a given extends the Newtonian viscosity region to lower rates of shear. A third factor which influences the

By D. D. Pollock, D. I. Finch

Relationships between the compositions of specially prepared manganin-type alloys and some of their electrical properties have been established. Empirical equations, based upon the electronic configurations of the alloying elements, are given which describe the resistivity, temperature coefficient, peak temperature, and thermoelectric power of Cu-Mn-Ni-Fe alloys at approximately room temperature. Calculations based upon these relationships are correlated with experimental data. SECURING suitable alloys for the construction of stable resistors, for use in precise electrical measuring devices, has been important ever since the art of electrical measurement was begun. German silver, Pt-Ag, and Platinoid are examples of some of the alloys in early use. These early alloys were un- satisfactory for one or more of the following reasons: l—insufficient stability of electrical properties with time, 2—poor reproducibility of electrical characteristics from melt to melt, 3—excessive temperature coefficients of resistance, and 4—excessive cost. Weston introduced the Cu-Mn-Fe and Cu-Mn-Ni-Fe alloys of the type now generally known as manganins. His patents are believed to represent the first disclosure of any alloy with a negative temperature coefficient of resistance. After this work, the German company, Isabellenhutte, in conjunction with Feussner and St. Lindeck, produced alloys of

Jan 1, 1957

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

Jan 1, 1915

By R. J. Brison, W. C. Bleimeister

The International Salt Company has long been interested in finding an efficient process for the removal of impurities from rock salt, and particularly from the rock salt produced at the Detroit mine. Methods which have been used previously at the Detroit mine included both hand sorting and differential crushing in a Bradford breaker with rejection of the oversize. Neither of these methods was adequately effective. The development of a new process for removal of impurities from rock salt has been described in the preceding article." Basically, the process consists of exposure of crude rock salt to radiant heating which selectively heats the impure particles. Subsequently the heated particles are removed by adhesion to a heat sensitive-coating on a conveyor belt. This method was found to be effective in improving both the quality and appearance of rock salt by the rejection of the dark, impure particles.

Jan 8, 1960

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By Eric A. Nordhausen

A good deal of dialogue has been published and voiced concerning one mining regulation or another, that, according to those raising the issues, in effect shuts down or drastically reduces mine and/or mill reduction. The objective of this discussion is to there fore synthesize the various regulations affecting the uranium mining industry and attempt to realistically assess the extent of impact to yellowcake production - on both an individual and collective basis. Emphasis is placed on the later or newer permitting requirements under the Mill Tailings Act, Underground Injection Control Program, the Consolidated Permit Program, and the Resource Conservation and Recovery Act (RcRA).

Jan 1, 1980

Jan 1, 1925

By C. McCulloch

OPEN-PIT mining of coal is relatively a recent innovation; men still active in the industry can trace its development. Re- viewing the growth of operations from the original horse-drawn scrapers, through the various stages of power equipment to the huge strip- ping shovels of today, one also notes changes in the methods of what the coal man calls preparation at the face. We really should not call it face preparation because, in contrast to underground mining, a face does not exist in strip mining. Further, preparation of the coal for market at the loading point has already, in but a few years, become largely of historic interest only and modern mines as well as old mines recently modernized rely almost entirely on separate and elaborate preparation plants to produce marketable coal. This practice was not voluntarily adopted by the producer but was forced upon him by the inadequacy of previous

Jan 1, 1939

By M. R. Geer, H. F. Yancey, P. S. Jacobsen

Two growing problems confront the preparation engineer—still further restrictions on stream pollution and a greater proportion of fine coal as more and more continuous miners come into use. The de-watering screens, centrifuges, and settling ponds that sufficed a few years ago must often be supplemented by more effective equipment, and in some instances the finest solids are now being recovered by vacuum filtration, once considered too costly in many coal washeries. Unfortunately not all slurries can be readily filtered. Some are virtually unfilter-able, and others do not permit the high cake rates needed to hold costs within reason. Often, however, these difficult slurries can be rendered filterable by flocculation. Starch and lime have long increased settling rate in thickeners and can also aid filtration. More recently there have been other flocculants, primarily synthetic polymers or gums. Reports of their great effectiveness prompted the U. S. Bureau of Mines to test their use in filtration as part of its program on recovering and cleaning fine coal. The object of the present work was to compare some of the newer flocculants with starch and lime and to test the reaction of different types of slurries to flocculation. Three natural slurries, three synthetic coal-clay mixtures, and five flocculants were tested, all with a laboratory filter leaf. Slurries and Flocculants Tested: First of the slurries was the thickener feed from the washed coal section of the Michel colliery of Crow's Nest Pass Co. Ltd., Michel, B.C. As shown by the screen and ash analyses in Table I, practically all this slurry was finer than 28 mesh, and about half the solids were finer than 200. Substantially all material coarser than 200 mesh was clean coal, but the ash content of 20.7 pct in the finest size indicates a moderate amount of impurity. This coal is medium-volatile bituminous in rank. Slurry was also obtained from the Black Diamond washery of Palmer Coking Coal Co., King County, Wash. This underflow of a 1/2-mm vibrating slurry screen is a waste product discharged to a settling pond. As shown by the data in Table I it contained about 20 pct material finer than 200 mesh, which analyzed 77.5 pct ash, indicating a high proportion of clay. The coarser sizes were also high in ash content because of the presence of bone and shale. Black Diamond coal is on the dividing line between bituminous and subbituminous rank. The third slurry, from the washery of Roslyn-Cascade Coal Co. in Kittitas County, Wash., was the underflow of a battery of 8-in. cyclones that is wasted with the coarser refuse from the plant. In both size and ash content this slurry was similar to the Black Diamond, but since it was a cyclone-underflow product, the fraction finer than 200 mesh undoubtedly contained a much smaller proportion of finely divided clay than was present in the Black Diamond slurry. The Roslyn-Cascade coal is high-volatile A bituminous in rank. Initially the slurry samples were stored in the laboratory at a concentration of 40 pct solids. A progressive change in filtration and flocculation characteristics during storage was noted, however, presumably because of progressive disintegration of the clay. After careful testing demonstrated that the slurry solids could be dried and then repulped without changing the original filtration characteristics, this procedure was adopted. The flocculants used were Separan 2610, Kylo 27, Jaguar MD-A, Idaho potato starch, and lime. The lime was used as a slurry, the Separan 2610 as a 0.10 pct aqueous solution, and the other flocculants as 0.50 pct aqueous solutions. The starch was causti-cized with sodium hydroxide before use. As some of the flocculants are reported to deteriorate on storage, new batches of flocculants were prepared every two days. Test Procedure: Fig. 1 diagrams the filter leaf apparatus employed. This consists of a test leaf having an effective area of 0.10 sq ft., a 60°, 8 1/2-in. diam cone to hold the slurry sample, a variable-speed electric stirrer, vacuum gage, bleed line for controlling vacuum, filtrate flask, moisture trap, and vacuum pump. Two filter cloths were selected—Saran SA 603, a monofilament, coarse-weave cloth, and polyethylene PO-801 HF, a monofilament, fine-weave cloth. The Saran was selected to provide maximum cake rate without regard to clarity of filtrate and the polyethylene to provide the best quality of filtrate without regard to cake rate. The test charge for the filtering vessel consisted of 800 g of solids (previously soaked for 24 hr) and

Jan 1, 1960

By AIME AIME

THE report of the united. States Steel Corporation for the' year 1928 gives the, following ,figures of raw materials and' finished products . Raw materials, tons :

Jan 1, 1929