Search Documents

By S. E. Bretherton

Discussion of the paper of S. E. BRETHERTON, presented at. the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1595 to1599. ANTON EILERS, Brooklyn, N. Y. (communication to the Secretary*). While the advantages in the use of high-line siliceous slags in lead smelting which Mr. Bretherton discusses in this paper are obvious under certain economical conditions, he gives me credit for the introduction of such slags when it does not belong to me. It is true I did considerable experimental work, off and on, for the purpose of finding such slags, while at the Germania in 1877 and 1878, but I did not have occasion to introduce any such slags for regular work, because I had no ores which fitted the economical conditions for using high silica and high lime, except in isolated cases for very brief periods. On the contrary, the ores I had to treat were mostly very ferruginous and very low in silica, so that, economically, I was compelled to run nearly always on slags, which allowed me to use the abundant flux I had without cost. It was August Raht who first had occasion to establish and use for long periods a slag high in silica and line, and low in iron. This was when he was confronted with the task of smelting the. Horn-Silver ores at the smelting works at Franklin, Utah, with as little expenditure for fluxing material as possible. I was at that time in Leadville, Col., where, in the new works I had built, the Billings and Eilers smelters, I had occasion to use profitably many slags, but never anything as high in the earthy bases and in silica as Mr. Raht had to use.

Jan 12, 1915

By Perry G. Harrison

The increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well.to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd continuously operated sinter-machine installations located anywhere. Per Crude Ton Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? Per Sinter Ton Royalty on ore 0.10 Royalty on flue dust 0.15 Per Crude Ton "Winter expense"; i. e., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for any ore, viz: Per Crude Ton Per Ton Handled Sinter 1. Flue Dust—Steel Plant Locations Sinter recovery, 15 per cent moisture and carbon 85 per cent Labor, supplies and repairs 0.15 0.18 Power 6.5¢ X 1¢ kw-hr. 0.065 0.08 Plant overhead and administration 0.05 0.06 Depreciation per ton 0.05 0.06 Dust handling and preparation 0.10 0.12 Fuel: free, contained in dust Ignition: blast-furnace gas free Royalty 0.15 Total $0.65 Note:—Cost increased by either deficiency or considerable excess of carbon in dust.

Jan 1, 1932

Alfred E. Hunt, Pittsburgh, Pa. (communication to the Secretary): Mr. Blue's statement (page 576) that, " owing to the presence of iron and other impurities, makers of aluminum. assert that native corundum is unsuited for the production of that metal," is somewhat incorrect, at least so far as it may refer to any objection made by the officials of the Pittsburgh Reduction Co. to the Canadian corundums. We recognize corundum as among the richest and purest of the ores of aluminum, and the material furnished from Canada would offer for us the advantage of a supply near to our works for the manufacture of aluminum at Niagara Falls. The real difficulty which we find in the use of corundum for this manufacture is the cost of the raw material as compared with that of native bauxites. In this item we include not only, the price of the corundum as it has been offered to us, but also the expense of grinding it to an impalpable powder, which must be done before it can be used directly in the manufacture of aluminum, and the cost of preliminary chemical treatment for purification—which latter operation, however, is also required for bauxite. I agree with Mr. Blue that the introduction of new and irnproved processes has greatly reduced, during the past ten years, the cost of manufacturing aluminum; but I am inclined to believe that any further improvements, facilitating the use of corundum for this purpose, would apply, in equal or greater degree, to the common clays (silicates of aluminum) which exist in all parts of the world, are more easily mined and handled, and are likely to be always cheaper per unit of aluminum than any corundum.

Jan 1, 1899

The following table summarizes the information on the Hurghada field. which is still the major producing field in Egypt. Age of field to end of 1937. years..................... 24 Producing area for gas and oil. acres.................. 1.050 Babbels Total oil production to end of 1937................... 30.188.500 Total oil production during 1936..................... 1.219.406 Total oil production during 1937..................... 1.141.230 Average oil production per acre to end of 1937.......... 28.750 Average oil production per acre-foot to end of 1937.... 2.359 Daily average production (Nov. 1937)................ 3.162 Daily average production per well (Nov. 1937)........ 41.88 MillionB Cu. Ft. Total gas production (Aug. 1925 to end of 1937)....... 4,189 Total gas production during 1936.................... 281 Total gas production during 1937.................... 222.5 Maximum daily average in 1937 (July)............... 0.7 Number of producing wells completed to end of 1937... 97 Number of producing wells completed during 1937..... 3 Number of wells abandoned during 1937.............. 1 Producing wells at end of 1937....................... 78= Total number abandoned wella at end of 1937......... 19 Total number dry wells at end of 1937................ 20 Average depth of bottom of producing horizon, ft...... 1,720 Average depth of top of producing horizon, ft.......... 1,598 Character of oil, approximate average in 1937: gravity at 60" F., 0.900; base, mixed. Character of gas, approximate average during 1937: gallons gasoline per 1,000 cu. ft., 6.9. Producing rock (main): Nubian (?) sandstone. Cretaceous (?); character, sand rock and sandstone. 1 Figures were given in E. tons. A conversion factor of 6.98, based on 0.900 sp. gr., was used to obtain the number of barrels.—Ed. *All pumping.

Jan 1, 1938

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

By Edward Keller

Under the title, Labor-Saving Appliances in the Works-Laboratory, I published a paper1 in which mas described how multi-manipulations in a works-laboratory and in the furnace-room of an assay-laboratory, can be condensed into single manipulations by applying the proper mechanical devices. For example, I now deposit ill, or withdraw from, a muffle a set of 48 cupels as one unit. The front row (8) of these are blanks or heaters; the other 40, when they have attained the proper temperature in the muffle, are charged simultaneously with the 40 lead-buttons. Three manipulations here accomplish an operation which by the generally customary method requires 136, and this number is only limited by the size of muffle and cnpels. This operation is an enlargement of what I have already described in my former paper, and Fig. 1 shows the improved implements. In the paper referred to I described a gold-silver bead parting-bath, which is the last of the devices used in regular sequence in practice. This bath mas designated as being convenient, but mas not a labor-saver properly. Fig. 2 of the present paper shows a new device. Instead of the original tray, there are now sectional holders for the test-tubes, each having a wooden handle on either end, so that the holders ma?-be removed from the boiling bath, and the acid or water poured oE from each set of tubes (in this case, 7) without waiting to cool. The tubes, held in place by clutches, as shown in Pig. 3, rest in holes in the base-strip, having a smaller diameter than the tubes. Each holder is stamped at either end with a number, so that the bath becomes further useful by permitting several men to use it at the same time without interference. Apart from the handles, the holders are made of sheet-copper.

Jan 1, 1911

The meeting of the Board of Directors, on November 22, was attended by eight directors, the Secretary of the Institute, and eight guests. The proposed James Douglas Prize and Tablet was referred to a committee of eleven. Robert H. Richards was appointed representative of this Institute to attend the meeting of the Society for the Promotion of Engineering Education. J. V. N. Dorr was made chairman of the Finance Committee in place of George D. Barron, resigned. The sum of $200 was appropriated for the 1918 expense of the American Engineering Standards Committee; the question of an appropriation for 1919 was referred to the Executive Committee for study and report. The sum of $50 was appropriated to the Treasurer's clerk. The following representatives of the Institute were elected: W. L. Saunders to succeed himself as United Engineering Society Trustee; R. M. Raymond to succeed himself as member of Engineering Foundation Board; S. J. Jennings to succeed himself as member of Engineering Council; George F. Kunz to succeed himself as member of Engineering Council; C. F. Rand to succeed himself as member of John Fritz Medal Board of Award; E. Gybbon Spilsbury to succeed himself as member of the Library Board. To members of the Canadian Mining Institute residing in Canada or Newfoundland, the privilege was extended to subscribe to the Bulletin at the price of $5. An invitation was extended to the Mining and Metallurgical Society of America to consolidate with the American Institute of Mining Engineers. The appointment of Engineering Societies' Employment Bureau was reported. Thirty-nine members and ten associates were elected. Two members were reinstated. Extension of time for the payment of clues was granted to four members. Seventeen members on active duty at the front had their dues remitted.

Jan 1, 1919

By J. L. Brimhall, R. A. Huggins

The structure of deformed internally oxidized alloys of siluer- cotztcrining magnesium and copper-containing aluminum in was studied by thin-film transrrzissiotz electron microscopy. With low to moderate amounts of stvain, the deformation structure in t11e dispersion-hardened alloys was found to consist of a high density of dislocations arranged it a random distribution or in a very fine, but poorly defined, cell stucture, depending on the fitness of the dbsbersion and amount of deformation. 112 contrarst, both pure copper and silver show relative1y Large, distinct cell structures. The particular structures in the alloys are believed to result from particles acting as both dislocaliot~ sources and deflector-s. The Inck of a pvorzolrr~ced deformation texture tr~ regiotzs qf' seoere loctll plastic curvature after heavy deformation can also be traced to the formation of clislocntions on many slip systemes and a lack 01 local concentrations of dislocations of predominantly one sign. THE presence of fine dispersions of a second phase has long been known to have a strong influence upon the mechanical properties of solids. Until recently, the influence of particles on the deformation mechanisms has been assumed to be solely that of barriers to dislocations. This is seen in the classic models of edge dislocations being restrained by the particles.1 4 There is, however, considerable evidence that this is not their primary effect, and that the particles can have a large influence on the defect structure generated by plastic deformation. The presence of particles causes changes in the surface topography observed after deformation. In overaged precipitation-hardened materials containing hard, noncoherent precipitates, fine intersecting slip lines are found after deformation of single crystals. indicating the activation of many slip systems. This has been extensively observed in the A1-Cu systen;, both by optical microscopy and replica electron microscopy.'"13 In some of the observations. the slip lines were seen to extend between the particles. Similar observations of extremely fine slip lines or the apparent absence of normal slip lines have also been found in A~-M~."

Jan 1, 1965

By E. Miller, J. M. Eldridge, K. L. Komarek

Activities of magnesium in liquid Mg-Sn alloys have been determined between 5 and 90 at. pct Sn and 990" and 1290°K by an improved isopiestic method wherein tin specimens, heated in a temperature gradient and contained in crucibles of special geometry, were equilibrated with magnesium vapor in a closed titanium system. The crucibles were designed so that the equilibrium compositions of the specimens were satisfactorily preserved on termination of the experimental runs by quenching. The activity values are in excellent agreement with those predicated on the phase diagram and allowed a delineation of the solidus curve of the compound Mg2Sn near its melting point. EQUATIONS have been recently derived relating the chemical potentials of the components to the liquidus and enthalpy data for binary systems exhibiting one congruently melting compound.' The liquidus curve of the Mg-Sn system between the eutectics was carefully redetermined and the thermodynamic properties thus calculated were in reasonably good agreement with values derived from electromotive-force measurements of an,' but differed greatly from the iso-piestically determined values of Ashtakala and Pid-geon.3 The present study was initiated: a) to resolve the discrepancies; b) to develop a method for measuring activities in systems having volatile (and possibly highly reactive) components; and c) to use the method in a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVb systems, i.e., Mg-Pb, Mg-Sn, Mg-Ge, and Mg-Si. This paper describes the results for the Mg-Sn system. An isopiestic technique, originally developed by Herasymenko 4 and adapted for alloys having a component of high reactivity and low volatility,5-8 was modified in this study by using crucibles designed to preserve the equilibrium composition of highly volatile liquid specimens on quenching from high temperatures. Tin specimens, contained in tightly covered graphite crucibles and heated in a temperature gradient, were equilibrated with magnesium vapor of fixed pressure from a magnesium reservoir kept at constant temperature in a previously evacuated and sealed titanium tube. During equilibration magne-

Jan 1, 1967

By C. P. Walker

Determining the distance to remote objects by observing the time required for sound to traverse the intervening space is an old practice. Attempts have been made to use this method for determining the fluid level in oil wells but as far as the writer is aware it was not found to be practicable, because vibrations in gas in the audible frequency range do not travel as well and as far as low-frequency pressure waves, which are capable of transmitting a greater amount of energy than can be transmitted by audible waves. Wood, in his book "Sound," states that in a given medium the range of sound transmission will vary inversely as the square of the frequency. The fact that the sound from a whistle having a low tone has a much lower attenuation rate than that from a whistle of high pitch is well known. Also, the pressure waves caused by cannon fire often rattle windows at points so distant that no sound of the cannon is heard. In 1932 P. E. Lehr and H. T. Wyatt, of the Shell Oil Co., experimented with the principle of the concussion, or pressure-wave echo, method of determining fluid levels in oil wells. They released compressed gas into the top of the casing, thereby creating a pressure wave, which traveled down the well and back again. Their experiments proved conclusively that, with the proper apparatus for recording the echoes and determining the velocities at which the waves travel, the method could be used successfully for determining fluid levels in oil wells. Wells are often equipped with from one to three tubing catchers and these together with the top of the liner are frequently above the fluid. Each of these obstructions reflects a part of the pressure wave. In such wells there may be, therefore, as many as five pressure-wave reflections. Thus it is obvious that in order to identify the various reflections and to determine therefrom the fluid level in a well it is necessary to obtain a graphic record of these reflections.

Jan 1, 1937

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By Thomas Downing

WHEN examining a coal property it is customary for the engineer to take channel samples at several coal faces. In doing so the extraneous matter, or partings, which can be removed by hand, or mechanically, with the facilities at hand, or proposed, is rejected. Where there is doubt concerning a stratum it is usually rejected from the main sample but part is taken for separate analysis. The samples are forwarded to a chemist for proximate analyses and determination of British thermal units, and, sometimes, ash fusion. Consideration is given all available commercial analyses but frequently the owner presents only the favorable ones. From the results thus obtained a general evaluation is made, monies are loaned or expended, markets are determined, and realization is estimated. In many instances, such grades are not substantiated and it is time we looked deeper for a basis which will prove more practical. Institute committees are working hard on analytic and use classifications and much valuable information has already been assembled and distributed. However, no single grade can be applied to any particular bed or region. Much study has been given the Pittsburgh No. 8 seam, yet that bed is subject to material differences in a single section; i. e., some strata of a face may differ from others in structure and analysis, particularly in sulfur content. From some localities it yields a good carbonization fuel, while in others it is chemically unfit for such use. Traveling south to the Logan, W. Va., field we find the Cedar Grove (Island Creek) seam a hard, gray splint coal. In the same field, and not far distant, the same bed changes, both structurally and chemically, and consists of excellent gas coal. In Illinois the moisture content of a bed may vary greatly in different localities. We have seen mines in which part of the coal is excellent for special purpose use but is spoiled by the product from another part of the same mine.

Jan 1, 1931

By J. G. Savins

Analytical procedures are described for optimizing the selection of a rheological model when it is desired to express the functional relationship between true shearrate and shearing stress in analytical form. The procedures are extended to two principal model categories — "Generalized Newtonian" and "Viscoplastic" models. Graphical examples are presented to illustrate the utility of certain characteristic deriuative functions in distinguishing between these categories and in determining how well a particular model reflects the flow behavior of rheologically anomalous materials in simple shearing flows. INTRODUCTION Modern drilling fluids and fracturing fluids, being chemically complex, are frequently non-Newtonian — a peculiarity which complicates the solution of problems such as designing flowline and process equipment, and predicting laminar-turbulent behavior, solid-suspending ability and cutting-transport efficiency. Therefore, techniques of data analysis which accurately characterize the behavior of rheologically complex materials are needed for the accurate formulation of solutions of these and similar problems. It is the purpose of this paper to describe the application of a sensitive method of rheological data analysis — the dual differentiation-integration method of optimizing the selection of the functional relation between shear rate and shearing stress — to a variety of materials of interest in drilling and production practices. BASIC CONCEPTS THE DIFFERENTIATION METHOD To a first approximation, the viscosity function for a non-Newtonian system can be expressed in a form analogous to Newton's law of viscosity by the following generalization2.3 between the stress On introducing the restrictions that the system is incompressible and the motion is rectilinear, then l = 0 and l3 = 0 ; and with the further restriction that the flow is slip-free, the viscosity (an invariant) is then determined solely by 12. With this approach one can set up a suite of integral equations relating observed kinematical and dynamical parameters for certain types of flow experiments involving simple shearing motion, e.g., flow in a cylindrical tube, flow between rotating concentric cylinders, and flow between fixed parallel surfaces of large aspect ratio. Taken in the order cited, these integral equations are as follows.

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1952

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By John Griffen

THE distinguishing principle of the Tromp process is the use of a medium in the bath which is not stable, i.e., the solids will settle and the density of the medium increases with depth. A medium of uniform density can most easily be effected by agitation or by means which increase the viscosity of the medium. Either of these works against the sharpness of separation of coal from its impurities. The Tromp process grinds the medium solids to relative coarseness, allows them to settle downward in the bath without hindrance, and introduces horizontal currents of medium at intermediate levels between top and bottom of the bath. This prevents any accumulation of particles denser than the upper layer of the medium from which the clean coal is conveyed away or an accumulation of particles lighter than the bottom layer or medium whence the refuse is removed. In a relatively shallow bath making a two-product separation, the intermediate horizontal currents sweep these intermediate gravity materials away to be discharged with the refuse removed by the conveyor. Such a system provides a number of advantages. The gravity of separation can be changed simply by changing the density of the medium without changing particle size of medium solids or other conditions, as would be necessary with a system requiring uniform or stable density throughout the bath. Some installations in Europe separate at 1.40 sp gr on one shift, producing a superclean coal, and on the next shift reclean refuse from dry cleaning units and effect a separation at 1.80 sp gr. Medium solids may be much coarser in size consist, which reduces the viscosity of the medium and promotes its fluidity and in turn the sharpness of separation. Coarser medium solids with a more rapid settling rate are much more easily recoverable from the dilute medium rinsed from the products. The Tromp process is not limited to the use of medium solids having magnetic properties. Instal-

Jan 1, 1953

By J. C. Jaeger

The study of brittle fracture of rocks has been a much neglected subject until quite recently and now is in a state of transition and rapid development. Historically, three methods of testing were used by engineers: uniaxial tension, bending, and, by far the most common, uniaxial compression of cubes. This latter was probably adequate for engineering requirements, but from the last century onwards there has been a demand from geologists for a study of the properties of materials under conditions comparable with those at depth in the earth&apos;s crust. King1 remarked that "in engineering practice a cube of the material is put into a testing machine and the stress required to crush the cube is measured. This gives the limiting stress difference for the material so long as the boundary conditions are similar to those existing during the test . . . this may by no means be the case when the boundary conditions are very different from those existing in the test, for instance, in the case of rupture in the neighbourhood of a cavity. . . ." Despite this very clear statement of principle, many writers until recently (e.g. Jeffreys2 used the uniaxial compressive strength as a measure of the &apos;strength&apos; of rock. In the last century (Becker 3, it was both conjectured and, for some rocks, known qualitatively, that plastic deformation could occur under confining pres- sure; the demand from geologists has been for the study of flow rather than fracture of rocks.. From the time of von Karman (1911) and Böker5 (1915) onwards, apparatus has been built which could provide confining pressures sufficient to make some rocks plastic. Many experiments tended to be made on rocks such as marble, which readily become plastic, and the general tendency was to make relatively few experiments in the brittle range. This is particularly true of many experiments on combined stresses. As a result of this, there is not sufficient data to provide adequate information

Jan 1, 1967

By R. N. Lambert

This chapter discusses the evolution of high-speed shaft sinking in the South African goldfields. Whether we are talking of an additional shaft at an existing mine or the opening of a new mine, the increasing depth of the ore-bearing reef and the unremitting inflation of costs have provided the compelling incentive to shorten the time taken to sink a shaft and start earning revenue. The high costs of sinking a modern shaft system in South Africa are indicated by the recent example of a deep-level mine in the Orange Free State where the cost was nearly $22!42 million. This was for a single large shaft of 33 ft 6 in. diam (in all cases, shaft diameters refer to the finished diameter of the shaft, e.g., inside the concrete) and 7600 ft deep with a prestressed concrete brattice wall dividing the shaft into upcast and downcast compartments. Higher costs and the consequent demand for increased tonnages, deeper shafts with higher rock temperatures, which necessitate highly sophisticaled ventilation and refrigeration requirements, have all accentuated the importance of time in a shaft-sinking operation. Rectangular shafts with their simple design and comparatively reasonable sinking speeds remained popular for many years until greater mining depths combined with a host of the other allied problems inevitably led to changes in shaft design. Circular shafts appeared to offer many advantages, particularly when considering ventilation, strength, mechanization, and sinking through bad ground and heavily watered zones. However, these advantages were largely offset by the slow rate of advance necessitated by the need to stop sinking in order to line the shaft. The development of the curb ring which enabled lining to take place above the bottom of the shaft and the use of multideck stages allowing sinking and lining to be carried out concurrently resulted in a major break- through. Rectangular shafts, which are still popular elsewhere, have been superseded in South Africa by circular shafts which are almost without exception the only shafts sunk in our goldfields today.

Jan 1, 1970