Search Documents

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By Potts N. L., Eilerts C. K., Summer E. F.

The second-order, nonlinear, partial- dillerential equation representing the transient radial flow of gas - condensate fluids in reservoirs has been integmted by using finite -dillerence equations and electronic computers. Effect was given to pressure -dependent permeability, viscosity, and compressibility and to distance-dependent permeability. The influence of a second-degree velocity term in the Darcy equation was investigated. Implicit methods were used and practical, convergent solutions were obtained with material balance to less than 6 x 10-4 for recovery of one- hall the reserve at constant flow rate. Integration results provide the productive period of a reservoir for a given constant rate and the fraction of the fluid initially in place that can be recovered in that period. The properties of a lean and a rich fluid are represented in a set of integrations designed to demonstrate the effect of different constant-recovery rates and significant variables emphasized one at a time. INTRODUCTION A method is needed for computing the availability or reserve of a gas in a formation, making use of all technical and engineering information that is pertinent. As a step in this direction, a program for computing transient linear flow1 was developed that utilizes principles of earlier finite-difference computing for a similar purpose2-4 and gives effect to significant pressure- and distance-dependent properties of reservoirs and their contents. The present paper pertains to transient, radial flow of gas-condensate fluids. In the partial-differential equation of flow, effect is given to the variables viscosity and compressibility,5 and also to permeability. Included in the study is the quadratic form of the Darcy equation of flow that has been the subject of field tests6 and that has been applied to a gas with constant properties in transient flow computing. 7 Inclusion in the differential equation of variable coefficients to represent properties greatly complicates the higher derivatives of the equation. Because it was impractical to make a required improvement in certain of the finite-difference derivatives by Taylor-series expansion, five-term derivatives were used in the implicit computing. Related methods were developed that can improve general facility in manipulating finite-difference equations. BASIC EQUATIONS PARTIAL DIFFERENTIAL EQUATION The basic partial differential equation for transient radial flow in the direction of decreasing radius is l_ a(vpr) _? .......(1) r gr at where r = radius, L v = apparent velocity aIong radius, L/t p = density, M/L3 t = time, t Ø = porosity, dimensionless. In this equation, only the porosity is regarded constant. The density is where p = pressure, m/Lt2 M = molecular weight of fluid, m T = constant temperature of fluid, T z(p) = pressure-dependent compressibility factor, dimensionless R = gas Constant, mL2/t2t. The physical boundary of the reservoir is at re, and the producing boundary is defined to be at tq with rq = re /200. By definition,

Jan 1, 1966

Jan 1, 1978

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By Allan Martin, R. A. Swalin

Diffusion rates of manganese, aluminum, titanium, and tungsten in nickel were measured at temperatures between 1100° and 1300°C. Activation energies, Q, and values of the frequency factor, Do, were calculated for each system. Values of Q were found to be within 15 pet of that for self-diffusion of nickel in agreement with present theories of diffusion. ONE of the most interesting problems in diffusion concerns factors governing the order of diffusion coefficients of various solutes in a common solvent metal at low solute concentrations. An early suggestion by Rhines and Mehl' was that diffusion coefficients might each approach that of the self-diffusion coefficient of the solvent itself. Later Thomas and Birchenall' pointed out correlations between the order of the diffusion coefficients and the freezing point depressions of the solvent by the various solutes. Other correlations have been sought. To settle this question it seems likely that much more data will be needed and, in particular, data collected at low solute concentrations. This type can be obtained by special analytical techniques as well as by use of radioactive tracers. The following study was made of diffusion of manganese, aluminum, titanium, and tungsten in a common solvent, nickel, at relatively low solute concentrations: 1—Production of alloys of nickel with manganese, aluminum, titanium. and tungsten at concentrations of the order of 1 atomic pet. 2—Use of pressure-welded diffusion couples in cylindrical form. 3—Diffusion anneals in the temperature range of 1100" to 1300°C. 4—Lathe sectioning of the diffused couples. 5—Spectrophotometric analyses of lathe turnings for the solute being studied. 6—Calculation of the diffusion coefficient for each of the solutes as a function of temperature. 7—Interpretation of results with current theories of diffusion. Experimental Work Materials—Two types of nickel were used in this research. The grade designated as Vacuum melted Mond nickel was used for all diffusion systems except the Mn-Ni system for which the Vacuum melted electrolytic nickel was used. Analyses of the two grades are given in Table I. The manganese used in making alloys was 99.9 + pet pure, aluminum 99.99 pet pure, titanium 99.9 pet pure, and tungsten of C.P. grade powder. Alloys used in this investigation were prepared by melting in vacuo or under a low pressure of argon. After melting, all heats except those of nickel-manganese were poured into a cylindrical copper mold 3 in. long and 1 in. ID. In the case of nickel-manganese, the alloys were solidified in the melting crucible. For nickel-aluminum heats alumina crucibles were used and for all other heats, zirconia crucibles.

Jan 1, 1957

By Charles S. Barrett

THIS paper is a progress report covering metallographic applications of the electron microscope that have been made during the past year at Carnegie Institute of Technology. An account is presented of the techniques that have been most satisfactory, the difficulties encountered, the resolution obtained, and the peculiarities that have been noted in the microstructures. About 12m exposures have been made during the year on the instrument, which is an RCA type B2 transmission microscope,1 and a number of these have been selected to illustrate the results obtained. Prints are also included showing the common types of falsities-to borrow a term from the biological field, the "artifacts." In brief, the paper is a record of our attempt to determine the value of the electron microscope in the study of the structure of metals and alloys. n addition to comments on techniques and the quality of photomicrographs obtainable with them, the paper discusses the nature of the etch attack on a few metals, and the possible relation between the fine structure revealed by etching and the mosaic block structure of the grains. Since numerous papers and reviews are available on the subject of imperfection in crystals, the comments here may be very brief; in fact, are restricted almost entirely to points having to do with recent theories relating the strength of metals to imperfections and to spacings of slip lines. SPECIMEN PREPARATION AND PHOTOGRAPHS Mechanical polishing by hand was used throughout this work. Precautions that must be taken in microscopy at high magnification, which have been well explained by Vilella in his book on Metallographic Technique for Steel, are likewise important with the electron microscope. This applies particularly to the need for repeated polishing and etching (each successive polish becoming less severe and each etch lighter), since the final etch should in general be no heavier than is used for oil-immersion optical microscopy and in many instances should be much lighter (compare Figs. 6a and 7a, 6d and 7b). An extremely light etch, of course, is incapable of cutting through a flowed layer of appreciable thickness. Unquestionably it would be very advantageous in each instance to compare the structures obtained by electrolytic polishing with those obtained by mechanical polishing, but difficulties with the electrolytic method have prevented this in the following collection of prints. The choice of etchant is important, of course; for example, picral proved superior to nital for tempered martensite. With the exception of Figs. Ib and IC, the replicas used were of silica, deposited up0n polystyrene and floated from the polystyrene in ethyl bromide according to polystyrene in ethyl bromide according to the method of Heidenreich and Peck.2 The samples were mounted in Bakelite, polished and etched, then the polished Bakelite

Jan 1, 1943

By D. K. Atwood

Experiments resulted in a satisfactory laboratory method for restoring permeability to clay-containing cores damaged by fresh water. Clay contents of a number of field cores were measured, and permeabilities of plugs from these same cores were then deliberately reduced with fresh water. This damage is attributed to swollen and dispersed clays occupying the pore space. After damaging, a number of experiments were performed to meaJure the amount of damage and to establish some means by which permeability could be restored. The experiments included flooding the damaged cores with water-miscible fluids such as salt water, acetone, isopropyl alcohol and ethanol. Permeability was not successfully restored in these experiments. However, part of the damage was repaired by flooding with oil; when water was removed by distillation in the presence of immiscible fluids such as air or toluene, permeability was completely restored. This evidence suggested that swollen and dispersed clays could be collapsed to their original volume by strong interfacial and capillary forces. It was further postulated that the required forces could be generated by flooding the damaged cores with a solvent partially miscible with water. The flooding experiments were repeated using n-hex-an01 as the partially miscible solvent. Permeability was restored to five of six damaged cores and substantially increased in the sixth. A large fraction of the restored permeability was retained even after water saturation was raised to its original value with 12 per cent salt water. INTRODUCTION Sharp reductions in permeability often occur when relatively fresh water contacts clay-containing formations during drilling and workover operations. These permeability losses are caused by removing inorganic ions from the environment surrounding the clay, and consequent swelling and/or dispersion of clay minerals into the available pore space.' This phenomenon is generally termed clay damage, fresh-water damage, or simply formation damage; it causes large losses in current revenue by preventing oil wells from making their allowable production. Attempts to repair the damage and restore permeability by flowing salt water solutions or brines through clay-damaged cores containing montmorillonite have been unsuccessful.' This irreversibility is thought to result from formation of brush-heap, or edge-to-face, structures when the dispersed clay is flocculated. The brush-heap structures occupy much more space than the close packed domains present before damage.' One solution of the problem is to destroy the clay-water brush-heap and thus restore permeability. Because no satisfactory method existed for restoring permeability to clay-containing formations damaged by fresh water, the work described in this paper was under taken. The laboratory experiments generally consisted of deliberately damaging fresh cores containing clay and then attempting to repair this damage by various means. Results indicate that generating strong interfacial forces within the pore space of damaged cores collapses the clay brush-heap and restores permeability. These forces are most conveniently generated by flowing partially water-miscible solvents, such as n-hexanol, through a core. THEORY OF THE DAMAGE PROCESS The most common clay mineral groups known to cause permeability damage to formations are the mont-morillonites, kaolins, chlorites and illites. These clays are constructed of particles which can adsorb water on their surfaces and edges and, in the case of montmorillonite, between layers of the basic particle itself. This adsorption increases as water salinity decreases. At low salinities the particles disperse into the aqueous phase. When the clays present in the formation are kaolin, chlorite and illite, dispersion accounts completely for permeability damage to porous media. However, unlike the other clays, montmorillonite particles can imbibe water and adsorb ions between layers of sub-particles, or platelets. These platelets have net negative charges on their faces and are held together by exchangeable (or removable) cations such as Na and Ca decrease in ion concentration (salinity) in the fluid surrounding a particle causes migration of water into the clay layers and disperses the basic particle, while diffusion removes the original exchangeable ions from between the platelets. Once these ions are removed, the facing negative platelets repel each other, causing the montmorillonite to swell until, for all practical purposes, the individual platelets are dispersed. For this reason, fresh-water* damage is much more severe in sands containing montmorillonite than it is in sands containing other clays. Many investigators have shown that even trace amounts of montmorillonite can be responsible for marked reduction in the permeability of reservoir sands in the presence of fresh water." ." Monaghan and others have shown that fresh-water damage in montmorillonite-containing cores cannot be

Jan 1, 1965

By Francis Foley

IN THE first report1 disks of steel of- known composition and history were exposed, under carefully prescribed conditions, to impacts of explosion products resulting from the explosion of 50-gm. charges of explosives having well-determined rates of detonation, or to, impacts of a weight of known mass, falling through measured distances. There were available at the Bureau of Mines Experiment Station five explosives, having rates of detonation of 5716, 4470, 3190, 2296, and 1523 meters per second. It being desired to continue this exposure downward, and no explosives with a lesser rate of detonation being at hand, resort was had to the impact of a falling weight, the differences in the velocity of impact being attained by varying the height from which the weight was allowed to fall. It was expected by this means to demonstrate experimentally that the development of Neumann bands was determined by the suddenness of the deformation of the metal in which they were produced. But while progressive deformations were obtained with the explosive charges, the falling-weight method failed because the tup was progressively deformed, also the disks were so flattened as to be unfit for metallographic examination. A return, therefore, has been made to the use of explosives as the source of energy, an air-gap being interposed between the charge of explosive and the disk, as the effect diminishes as the function of the distance between the charge and the object on which the products of its explosion, or the shock wave from its detonation, impinge. The details of the arrangement of the tests by the air-gap method were the same as those described by Foley and Howell,2 except that after the system had been set up and the desired apparent specific gravity for the explosive

Jan 2, 1926

By E. N. Skinner, Arthur Philliops

During the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson' who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.01; per cent at 1500ºC. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000ºC. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hemitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of mini-tie concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicro-scopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By E. N. Skinner, Arthur Philliops

During the course of an experimental program concerned with the hydrogen embrittlement of copper containing oxygen in concentrations within the solubility limits it became necessary to make a critical appraisal of the literature dealing with the solubility relationships of oxygen and solid copper. The latest determinations, and perhaps the only data obtained on "spectroscopically" pure copper, are those of Rhines and Mathewson' who reported that the solid solubility increases from 0.007 per cent oxygen at 600°C. to about 0.01; per cent at 1500ºC. Hanson, Marryat and Ford2 had previously placed the solubility limit at less than 0.009 per cent oxygen at 1000ºC. and Allen and Street3 had suggested, on the basis of an unpublished research by T. Hemitt, not over 0.005 per cent oxygen at 500°C. In the introductory stages of the investigation indirect evidence accumulated to suggest that the solubility limits were significantly lower than those previously reported. For this reason it was deemed essential to clarify this point before proceeding with a program intended to establish a quantitative relationship between hydrogen embrittlement and oxygen concentrations positively known to be within the solid solution range. Furthermore, the increasing production and the highly selective applications of the commercial "oxygen-free" coppers inevitably direct attention to the practical necessity for exact knowledge regarding the effects of mini-tie concentrations of the elements ordinarily found in the high-purity coppers now available. Of these elements oxygen occupies a unique position, not only by virtue of its specific effects on copper but more particularly in view of its important reactive tendencies toward the other impurities with which it is associated. Rhines and Mathewson considered several methods for measuring the solubility of oxygen and finally adopted the simple plan of saturating the specimens, obtained from redeposited cathode copper, by heating at the desired temperature in air. After the removal of surface oxide by mechanical and chemical means, the oxygen content was determined in the underlying metal. In general, this process of saturation, with a few modifications, was followed by the present writers. Although the procedure is direct and has obvious advantages, its effectiveness, unfortunately, is reduced by an excessive scaling of the copper, particularly at the higher temperatures. After saturation treatments above 900°C. the writers found that the specimens, necessarily rather thin in the original condition, consisted largely of scale and yielded too little metal for a satisfactory analytical sample. Furthermore, great difficulty was experienced in effecting complete removal of the scale. Needless to say, it is necessary to exercise extraordinary care in the preparation of the surface of the analytical sample in order to eliminate submicro-scopic fragments of cuprous oxide which ordinarily are lodged in the crevasses and

Jan 1, 1941

By M. Nicholas, D. M. Poole

The diameters of sessile drops have been found to increase linearly with time in five reacting binary metal systems. The spreading rates of the drops are markedly dependent on temperature and on prior alloying of the solid with the lower melting point metal, hut are independent of the drop volume, wetting atruosphere , solid-surface roughness, and prior alloying of the drop with the substrate metal. A mechanism has been suggested that relates the linear-spreading rate to lateral diffusion of the liquid-metal atoms into the solid at the drop edge. An Arrhenius- type equation has been derived that describes the temperature dependence 0) the spreading rate, and although the agreement between the actual and the predicted pre-exponen-tial terms is poor that between the activation energies is excellent and the variation in the spreading rate of copper on Ni-Cu alloys produced by different extents of alloying can be predicted with considerable accuracy. CHEMICAL interactions frequently change the wetting behavior of solid-liquid systems causing, for example, "secondary spreading1 of sessile drops beyond the size defined by the surface and interfacial tensions of the unreacted components. The kinetics of the contact-angle decreases associated with this spreading are similar for many systems, but few studies have been made with the objective of determining whether the similarities are a reflection of a common mechanism. Some workers2,3 have assumed the secondary spreading is controlled by changes in the liquid surface and liquid-solid interfacial tensions and hence by the composition of the liquid, and contact-angle changes measured by the vertical-plate technique have been used to follow the course of liquid-solid chemical reactions.4 Other processes that have been invoked to explain these time-dependent changes in specific systems include the removal of adsorbed gas from the liquid-solid interface.5 penetration of containment layers on the solid Surface,6 interdiffusion,1,7 reori-entation of the solid surface into a wettable configuration: vapor-phase transport of the liquid onto the solid in advance of the drop,9 and, from vertical-plate studies. capillary flow between oxide layers and the solid surface.10 One of the reasons for the profuseness of these suggestions may be the complexity of the contact-angle change kinetics. However, in an analysis of secondary spreading gold and copper on UC,11 it was found that the diameter of the contact area between the sessile drop and the solid surface showed a simple linear increase with time although contact-angle changes were more complex. To check whether the linearity was merely fortuitous! additional exploratory work was conducted with four reacting metal-metal systems: Au on Ni. Cu on Ni, Cu on Fe, and Ag on Au. Linear spreading was observed in every case even though the kinetics of the contact-angle changes were complex. A further detailed study of the kinetics of linear spreading of five reacting metal-metal systems has been made with the object of determining the mechanism involved. The influence of variables such as temperature, drop volume. and the initial composition of the drop on the linear-spreading rate has been measured and compared with those predicted by a number of possible mechanisms. The systems employed in this study (Cu and Au on Ni and Pt, and Ag on Au) were selected because of the availability of potentially relevant chemical and physical property data. the simplicity of their phase diagrams at the wetting temperatures, and the ease of experimentation. EXPERIMENTAL TECHNIQUES The purities of the metals used in the study were: copper, 99.9 pct; gold. 99.96 pct; nickel, 99.2 pct; platinum 99.99 pct; and silver, 99.999 pct. The wetting tests were performed in a split tantalum tube vacuum resistance furnace of a conventional design. The furnace element was held vertically and was 1 $ in. in diam and 6 in, long. Viewing ports were provided in the water-cooled chamber to enable the specimens to be observed in both the horizontal and vertical planes. The temperature in the hot zone of the furnace could be held at 1500" i 5°C for an indefinite time. The surfaces of the solid-plaque metals were ground flat on Microcut paper and both the sessile drop and substrate metals were ultrasonically cleaned in methyl alcohol prior to their insertion in the furnace. After loading, the furnace was pumped down to a pressure of 2 x 10-5 mm of mercury and degassed for 30 min at 900° to 950°C. The temperature was then increased at more than 100°C per min to that used in the wetting test. The vacuum at the wetting temperature was better than 5 x 10-5 mm of mercury. Dewetting and retraction of the drop on cooling did not occur and the contact-area diameters, therefore, were measured after solidification with a vernier traveling microscope. The diameters quoted later are arithmetic means of ten measurements. The standard error of the mean never exceeded 3 pct and was often less than 1 pct.

Jan 1, 1967

By W. A. Schaeffer, M. Albertson

The Yates field is situated in northeastern Pecos County, Texas. Its productive area is about 15,000 acres. Production is chiefly from limestone of Permian age. Depths of wells vary from 1100 to 1800 ft. Initial productions range from a few barrels to 8000 bbl. per hour. The field outlet has always been prorated. Gas-oil ratios originally varied from less than 100 cu. ft. up to 8000 cu. ft. per barrel at allowable production rates. The average ratio was about 500 cu. ft. Fig. 1 shows the structure of the field and the location of the Tippett lease, on which the original experimental tubing work was done. Before the latter part of the year 1929, little actual effort in practice had been given to determination of the conditions under which the highest efficiencies may be realized in naturally flowing wells. For the preceding few years attention had been given to gas-oil ratios and their possible reduction by maintenance of back-pressure by choking at the well head. Some attempts had been made toward reduction of ratio by bottom-hole choking. In late 1929, the Shell Petroleum Corp. started the experimental installation of specially designed flow columns adapted to high-pressure flowing conditions in the Yates field. The objectives in view were the attainment of low gas-oil ratios at low rates of flow and the maintenance of high bottom-hole pressures. All naturally flowing wells should be provided with a suitable eductor string immediately upon completion of the well, so that the benefits of efficient flow will be derived from the beginning. This paper presents a method of tubing for efficient flow and a discussion of some complex factors which influence well behavior. Factors Influencing Gas-oil Ratios Many factors influence the production of gas from naturally flowing wells. The writers believe that in some instances gas control is effected mainly in the reservoir itself, in others in the well bore, and in still others both sets of factors may be significant. Some wells apparently have penetrated productive zones in which practically all of the gas is closely associated with, and mostly dissolved

Jan 1, 1932

By Arthur Taggart

THIS paper describes the result of a series of experiments run in the laboratory of the School of Mines, Columbia University, during the winter of 1927-28. It shows that the several operating adjustments of a pneumatic table produce effects in the action of a, given coal that may be grouped into two classes, viz.: stroke length, speed and rocker-arm angle, which affect longitudinal travel; air supply and table slope (transverse and longitudinal), which determine transverse travel. The magnitude of the effect of the different adjustments varies. Some of the adjustments affect stratification of the bed, both as respects size and specific gravity of the bed components, as well as direction of travel. Operation of a pneumatic table is fundamentally different from that of a wet table in that the former exerts, through the air supplied, a force on the particles upward away from the deck which is lacking on the wet table while, on the other hand, it lacks the positive control over cross travel that is supplied by the wash and feed water.

Jan 1, 1929

By Howard N. Eavenson

One who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regulation of some sort is needed if any stabilization is to be achieved and if the wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920—to the end of 1934—the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing of the high wage scale of that agreement, which soon proved to be an uneconomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By Howard N. Eavenson

One who has been trained in belief in the law of supply and demand and its effect upon prices finds it difficult to adjust himself to the minute regulations imposed by the New Deal, and also to the bewildering changes of government policy as expressed within a short period of time between the antitrust laws and the N.R.A., and later by the Bituminous Coal Conservation Act of 1935. A survey of the coal industry since the World War, both in this country and Great Britain, however, shows that regulation of some sort is needed if any stabilization is to be achieved and if the wage structure and economic welfare of the many communities dependent solely upon coal are to be maintained. Let us look at what has happened to the industry since 1920, which can be considered as the end of the period affected by the war influence. This discussion will be confined solely to bituminous coal, although many of the general conditions are equally applicable to anthracite, the position of which now is at least as bad as that of the softer variety. Since 1920—to the end of 1934—the production of coal has decreased from 568.7 million to 358.4 million tons, or 37 per cent; the number of mines from 14,766 to 6,258, or 58 per cent; the average annual production per mine has changed from 38,512 to 57,425 tons, or 50 per cent. The number of large mines has increased considerably, and the number of men employed has decreased from 639,547 to 458,011, a reduction of 28 per cent, while the average output per employee has changed from 4.0 to 4.4 tons, or an increase of 10 per cent. The average price per ton of coal at the mine has varied from $3.75 to $1.75. During that time wages decreased largely until 1933 and since that time have increased, until now the rates paid are considerably above those in other occupations, although the actual yearly earnings are low, because of part-time work. From 1920 to the signing of the Jacksonville wage agreement in 1924, about two-thirds of the men were union members and practically all of the nonunion mines were south of the Ohio River; with the fixing of the high wage scale of that agreement, which soon proved to be an uneconomic one, many of the mines found that they could not retain their business, so gradually changed to nonunion. By 1928 the proportion

Jan 1, 1936

By J. C. Bokros

At temperatures above 950°F, zirconium which has been strained a critical amount will experience critical recrystalli-zation. The large grain size thus formed can result in a reduction in the fatigue life by a factor of 2 to a factor of 9 at both high and low temperatures. The critical strains for zirconium vary from 15 pct at 900°F to about 2 pct at 1125°F, while those for zircaloy III vary from 15 pct at 1050°F to 5 pct at 1200°F. Zircaloy II ,experiences no critical recrystallization up to 1200°F. ZIRCONIUM has become increasingly important for nuclear applications and is being employed in reactors at temperatures where recrystallization can occur. Recent work' on the fatigue properties of zirconium has shown that coarse-grained structures developed in zirconium during recrystallization have much lower fatigue lives than fine-grained material. The development of these large grain sizes under such conditions is well known to be the result of critical recrystallization.2-4 Briefly, critical recrystallization occurs when a metal is strained a critical amount and annealed in the recrystallization range. The critical strain is defined as that minimum strain necessary to promote nucleation in the time unit and temperature considered. The maximum grain size occurs at the critical strain, since at this strain the fewest stable nuclei per unit volume grow into new grains. Recrystallization is not evident below this; strain since the nucleation rate is vanishingly lolw, and metal strained more than the critical amount has a higher nucleation rate per unit volume which results in a finer grained structure. This paper describes the critical recrystallization observed in reactor-grade zirconium, zircaloy 11, and zircaloy I11 as a function of annealing temperature and temperature of strain. EXPERIMENTAL The zirconium used was hafnium-free, double arc-melted sponge obtained from the Bureau of Mines. The ingots were forged and hot reduced to 0.08 to 0.10-in. sheet and subsequently cold reduced to 0.035-in. sheet with intermediate and final anneals at 1200 OF for 15 min. The zircaloy II and zircaloy III used were 0.035-in. sheets in the annealed condition. Compositions of these materials as tested are given in Table I. To determine the critical strain at a given temperature, tensile specimens having a0.065-in. taper in a 2-in. gage length were machined from the sheets parallel to the rolling direction. The specimens were polished, etched, and examined metallographically to ensure that all of them were strain-free, initially. Tukon indentations were made every half millimeter along the gage length of each specimen. These served as fiducial marks enabling the plastic strain to be measured with a microscope and micrometer stage. The specimens were pulled to failure at a rate of 0.002 in. per min in an Instron tensile-testing machine. Three temperatures were used for straining: room temperature, 500 ºF, and 900 ºF. The 500º and 900 ºF tests were run in an argon atmosphere. Since the rate of work hardening changes with temperature, a different critical strain was obtained for each temperature of strain. Specimens, prepared in the manner described, were annealed in vacuunl at various temperatures ranging from 900" to 1200 F for up to 1000 hr, after which they were examined metallographically. The critical strain and the recrystallized grain size as a function of strain were determined for each specimen. Results for the same temperature and time indicated that the critical strain measured was reproducible to within 5 pct of each other. RESULTS AND DISCUSSION Since increasing the time of anneal increases the probability of the nucleation of a new grain, the critical strain decreases with time at a decreasing

Jan 1, 1961

By Zay Jeffries

Page Introduction............................. 474 Nature of Experiments ........................ 476 Materials Used in Experiments..................... 476 Description of Samples........................ 476 Details of Tests and Apparatus .................... 486 Determination of Elongation...................... 488 Determination of Reduction of Area .................. 488 Results of Tests........................... 489 Quantity and Arrangement of Amorphous Phase............. 497 Properties of Amorphous and Crystalline Phases............. 501 Intercrystalline Fracture........................ 530 Trans-crystalline Fracture....................... 531 Rupture ............................... 535 Explanation of Beilby's Results..................... 536 Mechanical Properties of Copper Wires................. 537 Mechanical Properties of Tungsten Wires................ 542 Mechanical Properties of Iron Wire................... 546 Effect of Diameter of Wire on Mechanical Properties........... 554 General Considerations on Properties of Metals at Very Low Temperatures .. 556 General Considerations on Physical Properties of Complex Alloys...... 557 Summary.............................. 559 Discussion.............................. 562 Introduction DuRing the period 1914 to 1916. the writer observed many times that tungsten wire could be drawn hot until it became brittle but on cooling to room temperature it became ductile again. In searching the literature for parallel cases. it was found that Beilbyl had produced hard-drawn wires of gold. silver. and copper that showed less than 1 per cent.

Jan 1, 1919

By A. S. Odeh

ABSTRACT A simplified model was employed to develop mathematically equations that describe the unsteady-state behavior of naturally fractured reservoirs. The analysis resulted in an equation of flow of radial symmetry whose solution, for the infinite case, is identical in form and function to that describing the unsteady-state behavior of homogeneous reservoirs. Accepting the assumed model, for all practical purposes one cannot distinguish between fractured and homogeneous reservoirs fram pressure build-up and/or drawdown plots. INTRODUCTION The bulk of reservoir engineering research and techniques has been directed toward homogeneous reservoirs, whose physical characteristics, such as porosity and permeability, are considered, on the average, to be constant. However, many prolific reservoirs, especially in the Middle East, are naturally fractured. These reservoirs consist of two distinct elements, namely fractures and matrix, each of which contains its characteristic porosity and permeability. Because of this, the extension of conventional methods of reservoir engineering analysis to fractured reservoirs without mathematical justification could lead to results of uncertain value. The early reported work on artificially and naturally fractured reservoirs consists mainly of papers by Pollard,l Freeman and Natanson,2 and Samara.3 The most familiar method is that of Pollard. A more recent paper by Warren and Root showed how the Pollard method could lead to erroneous results,4 Warren and Root analyzed a plausible two-dimensional model of fractured reservoirs. They concluded that a Horner-type pressure build-up plot of a well producing from a fractured reservoir may be characterized by two parallel linear segments. These segments form the early and the late portions of the build-up plot and are connected by a transitional curve. In our analysis of pressure build-up and drawdown data obtained on several wells from various fractured reservoirs, two parallel straight lines were not observed. In fact, the build-up and drawdown plots were similar in shape to those obtained on homogeneous reservoirs. Fractured reservoirs, due to their complexity, could be represented by various mathematical models, none of which may be completely descriptive and satisfactory for all systems. This is so because the fractures and matrix blocks can be diverse in pattern, size, and geometry not only between one reservoir and another but also within a single reservoir. Therefore, one mathematical model may lead to a satisfactory solution in one case and fail in another. TO understand the behavior of the pressure buildup and drawdown data that were studied, and to explain the shape of the resulting plots, a fractured reservoir model was employed and analyzed mathematically. The model is based on the following assumptions: 1. The matrix blocks act like sources which feed the fractures with fluid; 2. The net fluid movement toward the wellbore obtains only in the fractures; and 3. The fractures' flow capacity and the degree of fracturing of the reservoir are uniform. By the degree of fracturing is meant the fractures' bulk volume per unit reservoir bulk volume. Assumption 3 does not stipulate that either the fractures or the matrix blocks should possess certain size, uniformity, geometric pattern, spacing, or direction. Moreover, this assumption of uniform flow capacity and degree of fracturing should be taken in the same general sense as one accepts uniform permeability and porosity assumptions in a homogeneous reservoir when deriving the unsteady -state fluid flow equation. Thus, the assumption may not be unreasonable, especially if one considers the evidence obtained from examining samples of fractured outcrops and reservoirs. Such samples show that the matrix usually consists of numerous blocks, all of which are small compared to the reservoir dimensions and well spacings. Therefore, the model could be described to represent a "homogeneously" fractured reservoir. la this paper, the fundamental equation of flow

Jan 1, 1966

By C. R. Taylor, John Chipman

THE study of chemical reactions of liquid steel and basic open-hearth slag involves a complex slag system of at least eight important components, and often a number of others. In initiating an experimental program on the equilibrium relationship of slag and metal, it became evident that but little progress could be expected in the interpretation of the complex slags until an understanding had been gained of the simpler liquid systems composed of a limited number of slag constituents. The simplest system that in any way resembles open-hearth slag must contain lime, silica and iron oxide. Attempts to produce in an induction furnace slags containing only these constituents have met with serious limitations because of the solubility of refractories in the slag. Thus in acid-lined furnaces the slag is always saturated with silica and consequently contains between 48 and 63 per cent of this component. In basic-lined furnaces an undesired additional component, magnesia, is introduced to the extent of some 3 to 15 per cent, depending upon the acidity, sometimes with disastrous results to the furnace. Thus in a magnesia-lined furnace, Fetters and Chipman1 found it impossible to prepare slags in which the ratio (CaO + MgO)/SiO2 was less than that corresponding to the metasilicate (approximately 0.8: I). Between this composition and that of the true acid slags lies a field of composition about which very little is known and which cannot be explored by any ordinary means. This circumstance, as well as the desire to study the more basic slags in the absence of magnesia, calls for the development of a method by which slags may be brought into equilibrium with molten metal without coming in contact with refractory. Such a technic has been provided by the rotating induction furnace developed by Barrett, Holbrook and Wood.2 Three modifications of the rotating furnace were described by these authors. The first was essentially a rotating refractory cylinder containing the magnesia crucible, which was itself heated by a graphite crucible. In the second, only the magnesia crucible rotated, the cylindrical graphite heater being stationary. In the third, the coil and crucible revolved, and the metal was heated directly by induction. EXPERIMENTAL METHOD Furnace The furnace used in this investigation differed from previous designs and may be considered a fourth modification of the original rotating furnace. Its essential features are shown in Fig. I. The outer case A is a fire-clay flue liner for control of the atmosphere. The top B and base C are alberene stone. The coil supports D are of "Formica," a material formed from phe-

Jan 1, 1942

By C. E. Morris, S. R. Pollack

Current -vo1tage -temperature characteristics were studied for Al-A12O3-Al, Au structures. The oxide film was grown by gaseous oxidation in an 0, glow discharge. The electron-transfer mechanism was identified as tunneling and the barrier heights and thickness were determined. It was found that the barrier height at the parent aluminum-oxide interface is 1.5 ev and the built-in vloltage with an aluminum counter electrode is 0.35 v. The growth mechanism of the oxide is also discussed and it is suggested that Mott&apos;s theory is not applicable in describing the growth. Discrepancies were observed in the detailed comparison of tunneling theory, based on a trapezoidal model, with the data, and several possible explanations are discussed. THEORETICAL analyses of electron tunneling from one nonsuperconducting metal to another through an extremely thin insulating film have been presented.1-6 These calculations relate the current density, J, to the voltage, V, between the two metals, and to the temperature, T. The results of these calculations indicate that the magnitude of J and the detailed shape of the J-V characteristic will in general depend most strongly upon such properties of the insulating film as the thickness, the dielectric constant, and the structure of the electron energy barrier profile. The experimental results of many7-11 workers have corroborated the main features of these calcu- lations and have in fact been used to determine properties of the thin insulating film. It has been demonstrated, for example, that the tunneling current formulation of simmons4 is adequate to describe the observed J-V characteristic over approximately 10 orders of magnitude of current. Furthermore, from these observations and analyses, insight into the nature of the A1-A12O3 (thermally grown) interface region has been obtained.&apos;&apos; The temperature dependence of the tunnel current has also been studied and, although a self-consistent set of tunneling parameters can be chosen to describe these data at low voltages (i.e., <0.5 v), the tunneling parameters are different from those obtained from higher voltage (i.e., of the order of 1 to 5 v) measurements." We have measured the effect of temperature and voltage upon the tunnel current at higher applied voltages and find that the theory is inadequate to describe all of the effects reported here. A discussion of the origin of this inadequacy is presented following a description of the samples used for these experiments, and the experimental results. SAMPLE PREPARATION Metal-insulator-metal structures were fabricated in the following way. A 99.999 pct A1 charge was used to deposit, in vacuo, thirty films, 2000Å thick, onto a 1 by 2 in. glass substrate (7059 Corning glass). Prior to deposition the substrate was glow-discharged for final cleanup and then baked at 200°C for 2 hr at a pressure of 5 x 10-7 torr. The pressure during deposition of the metal films was 2 X 10-6 torr and the deposition rate was 50 to 100Å per

Jan 1, 1965