Search Documents

By R. B. Adamson

The fatigue behauior of irradiated copper single crystals is compared to that of unirradiated crystals. Proton or electron irradiation did not substantially change the fatigue-lzj.e, fatigue-hardening-, or slip-line characteristics, while neutron irradiation did appear to alter these parameters. Postfatigue transrrzission electron microscopy did not reveal any marked structural differazces between irradiated and unirradiated specimens. Possible dislocatio~a mechanisnzs to explain the observed behavior are discussed. A LTHOUGH considerable work has been done to ascertain the effects of radiation on the tensile properties of metals (e.g., Refs. 1 and 2), little work of a basic nature has been reported on the effect of radiation on fatigue properties. Since it is known that fatigue properties are sensitive to conditions at the surface of the metal, it was felt that charged particle irradiation, whose penetration into metals is very small, might influence the fatigue behavior. To investigate this surface effect, irradiations with 10 mev protons and 1.5 mev electrons were conducted. The range of 10 mev protons in copper is about 0.236 mm; which is very small compared with the thickness of the specimens used (1.53 mm). The range of 1.5 mev electrons is somewhat larger, on the order of 0.665 mm.4 On the other hand, irradiation with reactor neutrons produces damage throughout the entire specimen, so neutron irradiation can be used to study the effects of bulk damage. The damage introduced by proton and neutron irradiation is expected to con!ist of large interstitial dislocation loops,5 tiny (<25A) vacancy loops," and/or various vacancy-rich regions called depleted zones.&apos; In the case of electron irradiation at about -173°C the damage is expected to consist of isolated Frenkel pairs.&apos; The effect of radiation damage on the fatigue properties of some engineering materials has been reported,g,10 but the results are not clear-cut or consistent. SPECIMEN PREPARATION Zone-refined copper was used to grow single crystals by a modified Bridgeman technique in an inert helium atmosphere. Using a seeding method, single crystals were obtained as bars about 6 in. long with a cross section of 3 by $ in. Immediately upon removal from the split-mold graphite boat in which they were grown, the very soft bars were embedded in a room-temperature setting plastic. They could then be cut into specimen lengths without introducing any long-range damage. Generally, four or five specimens plus one seed were obtained from each bar. The plastic material was dissolved away in acetone and the orientation of each sample was checked by the standard Laue X-ray

Jan 1, 1968

By I. Fatt

Relative permeability and relative electrical resistivity curves are obtained for networks of tubes with a tube radius distribution by means of a network of resistors used as an analog model. These curves are similar to those obtained from real porous media. The effects of pore size distribution and network structure on relative permeability and resistivity are demonstrated. INTRODUCTION Study of the dynamic properties of networks of single size tubes in paper IT&apos; of this series has shown that the network model has flow properties similar to those observed on real porous media. The comparison of properties of single size tube networks with those of real porous media cannot be carried far because very few porous media have uniform size pores. The capillary pressure curve from most porous materials such as soil, sandstone, and sintered glass indicate that these materials have pore size distribution similar to those shown in Figs. 5-1, 9-1, and 10-I.† To properly test the network model, it is therefore necessary to compare the dynamic properties of real porous media with those of networks of tubes in which the tube radii are distributed accord- ing to the distributions in the aforementioned figures. A network in which the tube sizes are distributed cannot be treated in the same manner as a network of single size tubes. In the single size tube network, the relation between tube geometry, flow resistance, and tube volume did not have to be known if the assumption was made that whatever relation did exist was the same for all tubes in a particular network. In a network of distributed tube size, the relation between tube geometry and flow resistance must be known or assumed in order to replace the tubes by equivalent electrical resistors. Relation of Tube Geometry to Flow Resistance The interchangeability of tubes and electrical resistors in the network model is possible because of the analogy between Poiseuille&apos;s law and Ohm&apos;s law. Poiseuille&apos;s law for a cylinder is q= pr4/8µl ?P.........(1) where q is the volumetric rate of flow, µ is the viscosity, ?P is the pressure gradient, r is the tube radius, and 1 is the tube length. Ohm&apos;s law is I=1/R?E..........(2) where I is the flux and is equivalent to the volumetric rate in Poiseuille&apos;s law, R is the resistance, and ?E is the voltage gradient. Both laws give the flux as a function of the potential drop and the resistance of the medium. By analogy then, 1/R=pr4/8µl ?P...........(3)

Jan 1, 1957

By J. A. Lund, A. M. Lawson

THE structures of quenched eutectoid and hypereu-tectoid Fe-Cu alloys have been examined by X-ray diffraction and by optical and electron microscopy. The relevant portion of the Fe-Cu phase diagram is given in Fig. 1. Several values have been reported for the solubility of copper in a Fe at the eutectoid temperature, including 1.4 wt pct by orton&apos; and 2.13 wt pct by Wreidt and Darken.2 Alloys containing 4.8 and 7.5 wt pct Cu have been prepared from two batches of Ferrovac E iron (0.005C and 0.013C) and electrolytic tough pitch copper (99.90 Cu). Specimens of dimensions 0.8 by 0.8 by 0.1 in. were cut from hot-rolled material, austenitized, and quenched into brine at 25°C. Similar specimens were also cooled in the furnace, after a short soaking treatment at 1100°C, at a rate estimated to be 10°C per min in the temperature range of 900" to 500°C. X-ray diffractometry was performed on quenched and on furnace-cooled bulk specimens using iron radiation. Only a bcc phase could be detected in all samples. Lattice parameters were calculated from measurements on four lines, made up of two resolved high-angle doublets. Comparisons were made against a silicon standard. Results are shown in Table I. Based on X-ray diffraction studies of a series of alloys of lower copper concentrations, orton&apos; estimated that the tattice constant of a Fe at 25°C increases 0.0014A per wt pct Cu in solution. Extrapolating Norton&apos;s data, it may be concluded that all copper was retained in solution in the brine-quenched 4.8 pct Cu alloy, and that approximately 5 pct Cu was also held in solution on quenching the 7.5 pct Cu alloy. Typical microstructures of brine-quenched specimens, as observed by optical microscopy, are shown in Figs. 2 and 3. Precipitation of the E phase (copper-rich) occurred along the y grain boundaries on quenching the 7.5 pct Cu alloy, rendering them readily detectable in the microstructure, Fig. 3. The original boundaries in the 4.8 pct Cu specimens were gener- ally not discernible, however. This indicates that the z phase which was seen in the higher-copper alloy was probably of proeutectoid origin. Thin foils for transmission electron microscopy were obtained from bulk specimens by spark machining to 0.006 in. thickness, followed by electrolytic polishing. Typical transmission electron micrographs

Jan 1, 1967

JOHN W. BELL, *Montreal, Quebec, Canada (communication to the Secretary?). The test results in Mr. Taggart&apos;s paper will, I am sure, be recognized as a notable contribution, and of great assistance in the study of the performance of the Hardinge mill. I regret, however, being obliged to note that Mr. Taggart still retains. such confidence in the Kick-Stadler method of computing the ?relative mechanical efficiency" of crushing machines. The Rittinger-Kick graph submitted by Mr. Gates and the tests made at McGill University disclosed precisely the same fundamental defect in the Kick-Stadler theory. Consequently, I have been obliged to recalculate in terms of Rittinger surface units the results obtained in the 28 rock-crushing tests cited by Mr. Taggart, in order to find- out what the relative efficiencies really were. In order to show the large discrepancies between the Stadler and Rittinger R. M. R&apos;s, the most, efficient result disclosed by each method is represented by the number 100, and the R.. M. E.&apos;s for the other tests have been recalculated on this basis. The results will be found in Table 1. Personally, I look forward to the time when we shall cease to talk about "relative mechanical efficiency" and merely refer to the "efficiency" of a crusher. All that is required to accomplish this is to agree on a standard method for determining the "crushing constant" of a given rock and a standard method for calculating the efficiency. The figures in the fourth column of Table 1 have been derived by assuming a constant of 2,000 for the quartzite crushed in the Yale tests. The Stadler method sometimes indicates changes in efficiency produced by, changes in operating conditions, as I pointed out in a paper describing rock-crushing tests made at McGill University. It is, however, not enough to determine that certain changes increase or decrease efficiency; surely it is equally important to determine the magnitude of these variations. By examination of Mr. Taggart&apos;s results, I have been obliged to conclude that the size of feed and amount of reduction greatly influence the Stadler R. M. E. figures, that they are positively misleading. It should be mentioned that since the majority of the tests have been made at the least efficient feed rates, and since, moreover, it is one of the evidently very important factors affecting efficiency, it is possible that different results might be obtained by a high-tonnage feed series, and that

Jan 8, 1917

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8.9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3-s in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6.9 The measure of internal friction adopted here, I/Q, is (p) X the logarithmic decrement, a measure used by some writers, and is also (I/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°°C. As shown in Fig. i, the internal friction increased by only a factor of 2 from room temperature to 300°°C., then by a factor of 100 during the next :too&apos; interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction ~ e-HI/RT [I]

Jan 1, 1942

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Clarence Zener

The internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites, localized weak regions introduced by cold-working,6&apos;7 grain boundaries and possibly twinning planes.8&apos;9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, 3.i in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff. Experimental Method The experimental method used has previously been described in institute papers.5&apos;6&apos;9 The measure of internal friction adopted here, I/Q, is X the logarithmic decre- ment, a measure used by some writers, and is also X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the fundamental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. Experimental Results The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. I, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of 100 during the next Ioo° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e-H/RT [I]

Jan 1, 1943

By Clarence Zener

THE internal friction of nonferrous metals vibrating at low stress amplitudes has so far always been successfully interpreted in terms of inhomogeneities of one sort or another. Examples are the fluctuation of stress across a specimen vibrating transversely,1,2,3 the stress inhomogeneities due to the elastic anisotropy and partial random orientation of the individual crystallites,4,5 localized weak regions introduced by cold-working,6,7 grain boundaries and possibly twinning planes.8,9 Perfect single crystals are, by definition, homogeneous. Actual single crystals usually, perhaps always, contains some imperfections. The present investigation. was undertaken to determine whether the internal friction of single crystals may likewise be attributed to inhomogeneities. This study was made possible through the gift of a large single crystal of 70-30 alpha brass by H. L. Burghoff, of the Chase Brass and Copper Co. The specimen, ½ in. in diameter and 10 in. long, was similar to samples previously described by Mr. Burghoff.10 EXPERIMENTAL METHOD The experimental method used has previously been described in Institute papers.5,6,9 The measure of internal friction adopted here, 1/Q, is (1/p) X the logarithmic decrement, a measure used by some writers, and is also (1/2p) X the specific damping capacity, a measure used by other writers. In all measurements the stress level was kept so low that the measurements were independent of stress level. In all measurements in which the temperature was varied, observations were made as the specimen slowly cooled from its highest temperature. The specimen was vibrated transversely. Observations were made at the funda¬mental frequency and at the first overtone, of about 620 and 1710 cycles per second, respectively. No attempt was made to avoid acoustical losses. EXPERIMENTAL RESULTS The specimen was annealed for several hours at 450°C. The temperature dependence of the internal friction was then determined from room temperature to 400°C. As shown in Fig. 1, the internal friction increased by only a factor of 2 from room temperature to 300°C., then by a factor of l00 during the next 100° interval. These measurements are consistent with the view that the observed internal friction is the superposition of two distinct parts. One, dominant at room temperature, is nearly independent of temperature. This part may be accounted for by acoustical losses and by transverse thermal currents. It was not further investigated. The second part, when plotted in the manner of Fig. I, lies upon a straight line. Therefore it has a heat of activation H; i.e., it varies with temperature as Internal friction e~H/RT [I]

Jan 1, 1942

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By D. W. Mitchell

INE operators have a choice of several classi- fications of mechanical loaders. Within each classification there are many types and makes available. Table I lists loaders on which manufacturing data as to operating characteristics are available. This paper discusses the conditions met in a mine as they affect these characteristics. It is assumed that management will provide satisfactory engineering, supervision, power, maintenance, loader service within a concentration of workings, and a balanced working cycle served by balanced production equipment. These are factors which affect the optimum operational efficiency of a loader. The conditions which determine loader choice are: Height of Vein—The main limitation to the use of a loading machine is the height to which the vein is mined; i.e. a loader cannot be higher than the place in which it is to work unless rock is taken. Since there are several low vein loaders being developed and successfully applied, this does not appear to be a requisite of an efficient mining operation. The maximum useable height of a loader should be equal to the working seam thickness less a working clearance for travel and operation. A—Working seam thickness = B—Artificial roof support thickness = C—Safe headroom below support = (generally about 6 in.) D—Height of roadway = E—Total of B + C f D =_______________________ A—E = maximum loader height F—Distance from top of roadway to bottom of roof support = G—-Height of loader&apos;s coal or ore line (see Table I) = H—Difference between F and G = Size of largest broken particle + a safety factor of 2 to 3 in. H is a loadability factor and is important because the clearance over the top of the conveyor chain to the roof or roof support must be greater than the largest broken particle or else the particle and/or the conveyor chain may be broken. From this standpoint it might be desirable to use a lower height machine even though it may have a smaller capacity, though this is warranted only when increased lump realization offsets lower man-day and machine pro- duction rates. Ivan Given has stated, "Loading should not be handicapped by securing lump only to grind it in the breaker." Width of Working Place—The width of a working place is the greatest width a place may be safely driven. The working place includes not only the face but the roads the loader must tram when mucking out more than one face. The width is limited by the system of placing props with sufficient room between them for the machine runner (about 2 ft). Maximum width of place in which the loader will operate at maximum efficiency is determined by the type of mounting. With track-mounted loaders, maximum width of place is determined by maximum angular swing of the loading head and proximity of track to the face. The use of double track leads to added expense and operational complexities. Several mines that have used double-track systems have found that a substantial saving is made by the use of machines that load out wider places. Trackless loaders may work in rooms of any maximum width. Minimum width of place in which a loader will operate is determined by width of the loader plus a safe movement area for the operator. Often a barodynamic study of the mine will show that either an increase in room width and/or a change in the system of propping may be made by using roof bolting, full or part-width room timbers, removable aluminum I-beams at the face, etc. Increasing the width of a working place will, in general, increase loader operating efficiency by providing more material per fall and by decreasing the preparation and moving time per ton. A change in the system of propping that would increase the minimum width might permit the use of a higher capacity loader with safer working conditions. Proper face tirnbering is necessary to insure safety from roof falls and because the speed of preparation and loading generally increases since the men work with greater assurance and there is less chance of kicking out posts. Maximum Room Length—With the exception of the scraper and the duckbill, the limit to room

Jan 1, 1952

Alfred E. Hunt, Pittsburgh, Pa. (communication to the Secretary): My experience has been similar to that described by Mr. Sperry, regarding a 50 per cent. alloy of nickel and aluminum. Moreover, the same phenomena occur with a 50 per cent. alloy of iron and aluminum, manganese and aluminum, chromium and aluminum, or tin and aluminum. It seems that there is a narrow limit of composition of these metals, within which, when they are alloyed, they crumble down into a powder after standing for any considerable time. The resulting powder does not seem to be a separation or disintegration into the elements composing the alloy, but simply a powdering down of the alloy itself. The physical properties and utility of any of these alloys in pondered form have not been carefully investigated as yet, and offer a field worthy of further investigation. Samuel Peters, Pittsburgh, Pa. (communication to the Secretary) : In the early seventies, during the early days of the open-hearth process in this country, the writer was engaged as

Jan 1, 1900

By R. J. Charles, G. Agar

Experiments on single particles show that the amount of material created during impact that is finer than any chosen size is proportional to the energy of the impact. As the underlying principle of comminution, it might be stated that each unit of energy input to a given comminution system tends to add to the system an identical assembly of new particles and subtract an equivalent volume of larger particles. Thus, two of the consequences of the fact that each unit of energy tends to add identical assemblies of new particles to the system are: 1) on continued application of energy the total charge in any batch comminution system tends to assume the characteristics of this assembly, and 2) the process of comminution may be described by a relationship such as E = Ak-a. Recently Schuhmannl presented a theory of comminution which puts rational perspective on the extensive controversy surrounding most of the existent theories of comminution. With hindsight the origin of controversy can be ascribed to a relatively simple circumstance. In general, a progressive shift of a size distribution curve towards finer sizes is observed as energy is added to a comminution system. It is also observed that, with continued grinding, the size distribution curves usually change and appear to approach some constant shape. Inves-tigators generally felt that an appropriate method of relating and generalizing such data would be to consider the hypothetical case where particles in the system were uniformly subjected to comminution such that each of these particles, receiving its proportion of input energy, was transformed into a number of smaller particles of uniform size. Since the changes in shape of the size distribution curves during size reduction were clearly associated with the coarse particles in the system, it was also assumed that these changes accounted for little of the input energy and one could deal solely with the equilibrium shape towards which the size distribution curves tended. Although the unrealistic nature of the foregoing points of view was realized some justification was felt for such treatments since, in most cases, the resulting mathematical formulae could, by the adjustment of at most two parameters, satisfactorily describe experimental observation. Difficulties arose, however, in that the formulae required a specific influence of the feed size on the comminution process. In actual fact, the application of a feed size term in fitting experimental data was often found to be unnecessary or contrary to the above formulae. Secondarily, much discussion arose concerning the appropriate energy number that would relate the size change of one particle to the amount of comminution energy it received. As has been previously shown3 all the above theories that treat comminution as a continuous process of size reduction may be related to a proposition of the following form: dE = -Cfn [1] where dE is the increment of energy, dx is the size change, x is the particle size, and C and n are constants. It is now clear, as pointed out by Schuhmann, that Eq. 1 is inapplicable to comminution processes, since comminution cannot be considered other than as a discontinuous mixing process in which the overall size distribution of the product results from mixing, in various proportions, finished material with unfinished, and sometimes untouched, material. A striking illustration of this mixing phenomena may be obtained by comparing the size distributions of grinds in a typical batch ball mill with size distributions calculated on the basis of mixing various proportions of feed material with a ground material which obeys a power law size distribution relationship. Figs. la and lb illustrate such a comparison and the similarity of these figures indicates that mixing plays an important role in determining the overall shape of the product size distributions. Figs. la and lb illustrate, additionally, the underlying basis of the comminution theory presented by Schuhmann.&apos; In the preliminary grinding of relatively close sized feed particles in a batch ball mill, one may visualize that, when a successful encounter of a ball with a feed particle occurs, then the particle undergoes severe size reduction and the size range in which the resultant particles reside is far removed from the size of the feed particles. After a number of feed particles are reduced by independent but similar impacts and one examines the size dis-

Jan 1, 1961

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7&apos;e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,&apos; and Owen has started some detailed studies with a carbonyl system.&apos; A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4&apos;5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at&apos;ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936

By H. K. Shearer

There were no important developments in the oil and gas industry in South Arkansas during 1935. Oil production, totaling 11,138,340 bbl., continued the decline that has been normal since 1925, but the decline from 1934 was only 278,600 bbl., or 2.5 per cent. The principal decline was in the Smackover field, while only the Champagnolle and Garland City fields showed notable increases. More wells were drilled than in any recent year, with a total of 123 completions. There were 44 oil wells, with a total reported initial daily production of 10,013 bbl., or an average of 227 bbl. per well. Two small gas wells were completed in Union County, where the gas is used locally for pumping and field operations. There were 77 dry holes, of which 28 were in or near oil fields and 49 were wildcats. Active drilling oper-at&apos;ions declined from 65 at the beginning of 1935 to 41 at the end. Most of the drilling was done during the first part of the year, espr-chially (luring the flurry caused by the discovery late in 1934 of the "Taylor" sand production in the Champagnolle field, but the producing area was soon outlined. In November, 1935, the J. E. Crosbie, Inc., NO. 1 Sullivant in sec. 12, 17s. 14W., producing 560 bbl. per day at 3175 ft., opened a new sand lens in the eastern part of the field. The Camden "oil field," discovered in the last week of 1934, remained a one-well field, although four offset tests were drilled, besides a number of others in the immediate vicinity. Several interesting deep tests were drilled during the year, which added a great deal to the general knowledge of the subsurface formations and the structure of south Arkansas, but were not particularly encouraging as to prospects for the very deep production. First, the H. L. Hunt, No. 15 E. F. Gregory well in sec. 10, 17S., 14\W., in the Champagnolle field, was drilled to a depth of 6911 ft. It pene-trated red beds for 2982 ft., from 2943 to 5925 ft., mostly if riot entirely of Lower Cretaceous age. There was some anhydrite in the last 135 ft. of red beds. This was followed by 890 ft. of limestone, probahly Permian, and the rock salt was struck at 6815 ft. The salt is now generally conceded to be of Permian age. Finding salt in this well strongly indicates

Jan 1, 1936

At the University Club, New York, Jan. 23, Chairman George E. Hale and other officers of the National Research Council, gave a dinner to officers of the national engineering and other societies. About thirty persons were present, including officers of the National Research Council, the four Founder Societies, American Society for Testing Materials, Society of Automotive Engineers, Inc., Illuminating Engineering Society, United Engineering Society, and Engineering Foundation. Letters were received from the Western Society of Engineers, which also had been invited. Gano Dunn, vice-chairman of National Research Council, was toastmaster. The proposed permanent organization of the National Research Council and possible methods of connection with the national engineering societies, either directly or through Engineering Foundation, were outlined. It was suggested that not only the four Founder Societies be represented in the Engineering Division of National Research Council, but also that the other national engineering societies be admitted to membership. It was proposed that the Engineering Division should have a chairman who should be an engineer of wide reputation and of the highest professional attainments who should devote his whole time to the establishment and development of the Division. Methods of organizing industrial research were discussed. At a subsequent meeting of the National Research Council, an invitation was issued to each of the national societies to form a research committee encouraging that committee to become active in the promotion of research within its respective field. Due recognition is to be given each committee in the general organization of the National Research Council. Dr. H. M. Howe, in a very interesting and comprehensive address, told of much important work that had been clone by the various sections of the Research Council, as that of mechanical engineering in developing the often rather nebulous devices for helping win the war and putting them in such form that they could be of direct use to the military service. The section on metallurgy, till lately under Bradley Stoughton and now under G. H. Clevenger, did much valuable work in the improvement of helmets and body armor and made very extensive ballistic tests with refractory steels for this purpose. Important work was done in investigating the fatigue of metals and results of great moment were achieved. The committee on ferro-alloys, under J. E. Johnson, Jr., did important work in effecting economy of manganese in steel manufacture with a view to reducing the necessity for importation of manganese ore, thus releasing ships for other purposes. , The section on electric welding has accomplished valuable results in the development of electric welding for ships, a new branch of industry of very great promise.

Jan 3, 1919

By Jack C. Bokros, Philip C. Rosenthal

DEVELOPMENT of the autoradiographic method in metallurgical research has been directed mainly toward gaining higher resolution, i.e., toward being able to locate segregation of a radioactive isotope on a finer scale. In the investigation reported, the liquid emulsion autoradiographic technique&apos; used in the biological science was adapted to the autoradiography of metals. The distribution of carbon-14 in pure iron after various treatments was studied using this technique. Amorphous carbon uniformly labelled with carbon-14 at a specific activity of 6.95 microcuries per millimole was obtained from Tracerlab Inc. Carbon-14 emits P particles having a maximum energy of 157 kev and an average energy of about 50 kev. These ßs have a maximum range of about 30 mg per cm&apos; and a half-thickness of about 3 mg per cm2. The iron used was spectroscopically pure electrolytic iron prepared by the Oak Ridge National Laboratory. Unhardened nuclear track emulsion, type NTB, was kindly supplied by the Eastman Kodak Co. This emulsion contains approximately 80 pct Ag halide,

Jan 1, 1957

By R. S. Newlin

IN reality, the Butte district is the birthplace of the Anaconda Copper Mining Co., for it was here that strength was gathered and means provided for later expansions of the Company. The Butte district was organized at a miners&apos; meeting on Aug. 20, 1866, primarily for gold placer-mining operations. Substantial amounts of placer gold were recovered from gulch gravels during the period 1862 to 1868. The earliest lode claim locations in the district were recorded in July and August 1864. Copper ore was first shipped, to Swansea, Wales, in 1866. In November 1866, according to the Montana Post, construction of a smelter was started to treat the silver

Jan 1, 1948

The University of Chicago Press, 5750 Ellis Ave , Chicago, Ill This Press publishes books on a wide variety of subjects of scientific interest, as well as several journals Only a few books on geology have been published, however, and the Journal of Geology. The Journal of Geology: A semiquarterly standard American publication in the geological field. $6 per year, single copies, $1, back numbers, within the past five years, $6 per volume Books on geology: The origin of the earth, by T. C Chamberlin, $2 50, Two solar families, by T. C Chamberlin, $2 50, Quantitative classification of igneous rocks, by W. Cross, J. Iddings, L V Pirsson and H. S Washington, $1.75; Studies in minor folds, by C. E. Decker, $1 50; An introduction to the study of ore deposits, by F. H Hatch, $3, A descriptive petrography of the igneous rocks, by A. Johannsen, $4 50, Essentials for the microscopical determination of rock¬forming minerals and rocks, by A. Johannsen (revised ed ) $3, Outlines of geologic history, with special reference to North America, edited by R D. Salisbury, 8150

Jan 1, 1933

By W. R. Ingalls

SOME months ago, I had occasion to make an investigation that introduced the subject of blue powder that is produced as a byproduct in zinc dis-tillation. Although every zinc smelter is aware that more or less blue powder production is inevitable and there is a common practice as regards the treatment of it, the specific and quantitative data respecting the subject were more imperfect than would have been expected. I had reports from eight important works. Some of the data were especially determined for my investigation. Speaking generally, there is a good deal of uniformity in the figures, all of which show that the blue powder product, bears a large proportion to the ore originally charged into the retorts; that a large proportion of the retort capacity is devoted to the redistillation of blue powder; and that of the spelter product of a furnace about 30 per cent. is derived from blue powder, i.e., it is zinc that has been distilled twice. The figures from the works are given in the following table:

Jan 4, 1922