Search Documents

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By R. A. Matuszak

This paper discusses the major portion of the hoist (drag or crowd) system and it shows how static control accomplishes its major aims. In 1959, the first truly static control for Ward-Leonard equipped electric excavators was designed, developed and placed in service. The control system, originally intended only as a more modern electronic type of alternate to the proven rotating amplifier control system has since proven to be much more. When they conceived the original system, the designers had much more in mind than simply replacing the rotating amplifier with one that had no moving parts. The long range plan, which started with the initial system consisting of an SCR (silicon controlled rectifier) preamplifier and magnetic amplifier power amplifier, called for eventually, a control system low in cost and maintenance, relatively simple in design and extremely reliable. The plan also included the elimination of as many of the shortcomings of the rotating system as possible. No small accomplishment, when it is considered that the rotating control system had been, with only minor modifications, the standard of the industry for 20 years. The final step in the original design plan called for the eventual development of an amplifier that could be used as one of the basic building blocks of the future. DEVELOPMENT RESULTS Since the successful unveiling of the first static control system, continuous development has resulted in a slow, but sure progression along the path described by the original plan. The first version of the new control corrected one of the shortcomings of the rotating system by removing the necessity of operator anticipation. This was accomplished by making the system faster in response so that the operator noticed virtually no delay between his movement of the master controller and that of the machine. Thus, after the operator became familiar with the operating characteristics of the machine, he was able to become more relaxed while digging. The natural result of this accomplishment was higher production. All of the subsequent versions of this new control were even faster than the initial design. Although it was not distinguishable by the operator, the further increase in response resulted in large gains in the limiting of transient torque peaks applied to the machine while digging. Also, a more effective control of the torque and power peaks was obtained when plugging the motion being controlled to a stop. (Plugging is the use of the Ward-Leonard ability to regenerate power and absorb energy from the load to

Jan 1, 1964

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

EUROPE continued to be unsettled, financially, commercially and socially. October opened with Germany in a state of turmoil following the Government's cessation of passive resistance to the French and Belgians. In many places there were riots with much bloodshed. In Bavaria a military dictator-ship was set up in order to keep peace. In the meanwhile France continued in an uncom-promising position.. Great Britain, having been diplo-matically discredited, disappeared from any prominence in the international picture. Under the constraint of circumstances the policy of deflation in Great. Britain was temporarily abandoned. Perhaps no other course was open, for with declining trade and heavily reduced revenue, and no chance for cutting expenses propor-tionately, a check to deflation comes of its own accord. The effects of this should become manifest in the course of a few months and should appear in the form of an improved margin between the prices for commodities and the wage costs in producing them. About Oct. 20 an effort was made to set up the Rheinland as a separate republic. On Oct. 26 were published communications from Lord Curzon to Secre-tary Hughes and the latter's reply. In these Lord Curzon drew attention to the gravity of the situation in Europe and expressed the hope that France might listen to renewed suggestions for a general inquiry. Secretary Hughes promised American cooperation, in this, with the reservation that the question of inter-national debts should not enter into the situation. In the latter part of October there were military mutinies and disorders in Greece, which resulted in the reestablishment of martial law by order of Col. Plas-tiras, who is virtually the dictator of Greece. The incipient revolt was promptly crushed.

Jan 10, 1923

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

By Jules E. Jenkins

IN the past quarter century the seismograph has played an increasingly important role in evaluating vibratory effects transmitted to adjacent communities by industrial blasting operations. In this period research has advanced through two major phases—from falling pin seismometers to three-component recording seismographs. The initial phase of this research is now regarded as the era of recording, during which the seismograph merely recorded occasional events. It has emerged from this stage into the era of control and analysis and in this later period has been recognized as a full-fledged industrial tool. Although the falling pin machines of earlier years indicated probable amplitudes of industrial blasting vibrations, they gave no reliable measure of such displacements, nor did they provide essential information concerning direction or frequency of motion. The first contribution of the three-component recording seismograph was the weight-for-distance formula developed by the U. S. Bureau of Mines. This empirical formula enabled users of commercial explosives to determine beforehand the probable vibratory effects of a blast when the weight of the explosives charge and the distance from the shot point were known. This formula has withstood the test of time and is still applicable for blasts detonated by instantaneous methods. The second major contribution of the three-component recording seismograph followed the introduction in 1945 of short period or millisecond delay detonation. This might be described as a two-stage contribution, the first of which revealed a 50 pct reduction in the vibration magnitude when millisecond detonation was used rather than instantaneous discharge. This second part of this double contribution led to the discovery of the vibration dip phenomena, see Fig. 1. In Fig. 1 the horizontal coordinates indicate the displacements amplitude in inches, and the vertical coordinates, the explosive weight in pounds. The top curve is that of the U. S. Bureau of Mines for instantaneous detonation. Its curvature conforms to the two-thirds power of the explosive weight as provided in the weight-for-distance formula; hence the vibratory effects increase in proportion to an increase in the explosive charge. If the other curves shown below are temporarily disregarded, it may be considered that the entire area below this top curve represents both useful and waste energy. As mentioned previously, when millisecond delay detonation was first investigated it was found that in general the U. S. Bureau of Mines curve could be decreased by about 50 pct, or to the position of the middle curve. At the outset it was assumed that this curve would likewise increase in some proportion to the explosive charge, as did the top curve, that is, the curve would indicate a continuous upswing. As seismographic data accumulated this assumption was found to be erroneous in part. It was discovered that

Jan 1, 1957

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.'-'0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3'5 intercept length,6"9 or diameter.1'2'4'10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

By S. F. Urban, G. Derge

AT the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for a large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions [f] operation. The most important general conclusion reached was that the time a heat is held under a reducing slag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. PROCEDURE The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. Companion slag and metal samples were taken just prior to slag-off and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional 13 heats. Slag sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from tie furnace in a well-slagged carbometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace heats. The Big Wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness, and was finally adopted as the most satisfactory design. The Long Wedge Mold (b) was a 2 by 2 by 5 ¼ -in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 2 ¾ in. long, and ¼ in. maximum thickness. The Small Wedge Mold (c) was 2 by 2 by 4-in. split copper mold, yielding a wedge-shaped casting 1 in. wide, 1 ½ in. long, and ¼ in. maximum thickness.

Jan 1, 1947

By Gerhard Derge

THE extension of metallurgical control of steelmaking processes has always made it desirable to have some quick method for determining the oxygen content of molten steel. To meet the practical demands of the steel industry, this method must also be simple enough so that the sampling can be done by the regular furnace crew. This requirement was kept in mind continually in the work to be described. An oxygen value is required for proper control, whether it be of a rimming steel or of a fully killed steel. However, two factors have discouraged the development of such direct methods: I. The reaction C + FeO -+ Fe + CO is rapid enough to make the correct sampling of the bath a difficult problem. The most generally accepted means of circumventing this difficulty have been the aluminum-killed bomb test of McCutcheon and Rautio1 and the aluminum-killed spoon test of Herty.2 The theory of these tests is that all of the oxygen in the iron is converted to A1203, which can then be determined by chemical methods. Even when simplified so that the analysis is made by a measurement of turbidity, this method is too slow to be used in routine control. Furthermore, the results obtained have never been entirely satisfactory, and some of the reasons for this will be discussed later in this paper. 2. The ordinary chemical methods of analysis for oxygen in steel are not reliable. The only analysis that seems to possess sufficient dependability to be of value is vacuum fusion,3 and the apparatus and technique developed for this have been too complex and slow for routine work. INDIRECT METHODS Indirect methods of estimating the oxygen have been resorted to in mill practice. Generally these depend upon the chemical equilibria involved. The oxygen in the bath is related to other components in the slag or metal that can be analyzed more readily. These methods have many difficulties in common. Steelmaking processes involve a complicated set of interrelated reactions, all of which tend to approach equilibrium at varying rates. The degree to which any particular equilibrium is approached, is not , well established. Moreover, a proper use of theoretical equilibrium constants requires a more extensive knowledge of the activities of the reactants than we now have. This is well illustrated by the irregularities observed when trying to determine the oxygen in the metal by its ratio to the iron oxide in the slag. Equilibrium relations may be used more readily if they are evaluated by plant experience, but the extent of approach to equilibrium remains an undetermined variable and lack of an entirely satisfactory means of determining oxygen for the calibration is felt keenly. For example, the statistical analysis of the relation between carbon and oxygen4 5 illustrates that even in a single plant wide variations exist under normal conditions of operation. Nevertheless, this is one of the best methods now

Jan 1, 1943

By A. W. Gauger

WITHOUT QUESTION the Commonwealth of Pennsylvania contains the most remarkable coal deposits of the whole world. Within its borders ,are to be found excellent coals ranging in rank from the high volatile bituminous of the western part of 'the state through the low volatile or semi-bituminous of central Pennsylvania to that aristocrat of solid fuels, anthracite, found in the East. . . . But while other states and even the Federa1 Government have recognized the needs of the coal industry, Pennsylvania has not. Though bituminous coal represents one of the most important industries in the state, far more important in annual productive wealth than agriculture, for example, hundreds, of thousands of dollars have been spent on agricultural research whereas little or nothing has been spent on coal investigation.

Jan 1, 1932

By J. R. Linney

THE Eastern Magnetite Industry produced approximately 7,850,000 long tons of crude ore in 1945 from which was obtained approximately 3,650,000 long tons of shipping product or a ratio of 2.10 to 1. Lack of skilled or experienced miners was the greatest handicap. Veterans returning to work improved the underground labor shortage in some localities but as a whole the labor shortage was keenly felt throughout the industry. One cannot now predict what may be accomplished in 1946 but barring major steel strikes a worthwhile improvement can be expected. At the Richard mine of the Richard Ore Co., the shipping product for the year amounted to approximately 124,650 long tons of concentrate and lump ore. Crude-ore production was 160,600 long tons. The average analysis for lump ore was 63 per cent iron and for concentrates 66.05 per cent. The Warren Foundry and Pipe Corp. at their Mt. Hope mine produced 73,000 long tons of lump ore averaging 59.5 per cent and 57,000 long tons of concentrate averaging 67 per cent. The total mine hoist was approximately 209,000 long tons. Operations were commenced through the new Leonard shaft on Jan. 18; the Brown shaft through which operations had been conducted since 1912 caved beyond repair on Sept. 26. No one was injured but pumping facilities were somewhat disrupted. In order to reach designed capacity a total of 400 men will be required with 300 underground. Due to shortage of labor all operations in 1945 were concentrated on the 1700 level. As fast as men can be hired and trained development of the 2100 and 2500 levels will commence. Mt. Hope has a consider-

Jan 1, 1946

Coal Division Mineral Industry Education Division Industrial Minerals Division Minerals Beneficiation Division Mineral Economics Division Mining, Geology and Geophysics Division Council R C Stephenson, Chairman (Ind Min Div), M D Cooper (Coal), H F Yancey (Coal), S D Michaelson (MBD), Will Mitchell, Jr (MBD), J R Van Pelt, Jr (MIED), S S Cole (Ind Min Div), J D Forrester (MGGD), L E Shaffer (MIED), E L Clark (MGGD), C W Merrill (MED), E H Robie, Acting Secretary, 29 West 39 Street, New York 18, New York

Jan 1, 1955

By G. H. Kennedy, H. E. Criner

CYCLONE thickeners are "hydraulic centrifuges" designed either to produce a maximum practical separation between the water and solids of a feed slurry or to classify the slurry solids according to particle settling rate. The possibilities of utilizing the thickener to "close" plant water circuits have been investigated. Since the thickener becomes an integral part of the plant water circuit when installed, the basic means by which the solids content of all circulating water systems must be controlled is reviewed. All coal not separated from the circulating water by means of dewatering screens or settling devices must be bled from the plant at the same rate as they are being fed or created by degradation. If this were not true, the circulated volume would finally be completely filled with solids. If the rate of bleed is low, the solids concentration in the bleed and circulating water generally will be high. To keep a reasonable circulating water concentration, large amounts of fresh water must be supplied and the bleed rate must be high. These conditions are usually undesirable because of the difficulty in securing fresh water, the loss of large quantities of coal, and the pollution of nearby streams. Thickeners are the primary stage in the separation of the water contained in the bleed from the coal. Since a thickener, when operating with reasonable efficiency, usually cannot be expected to deliver an underflow containing less than 50 pct water, secondary dewatering devices such as a slurry screen or vacuum filter must be used to separate additional water from the bleed. The surface area required by the filter or screen will be nearly proportional to the total water which must be handled, and therefore the thickener becomes necessary to hold down the original cost. The water separated from the coal is then returned to the plant circuit to maintain the water balance and thus becomes the source of fresh water. It is not necessary to return clear water to the plant to maintain control of the circulating water concentration. It is only necessary that the bleed dewatering devices remove coal in all sizes at a rate equal to that at which these sizes are entering the circulating water. However, practically speaking, in order to maintain low solids concentration, it is usually necessary that the thickener have good recovery characteristics on bituminous coals in those sizes down to 400-mesh. The thickener can remove the smaller sizes from the closed-circuit system at the "solids in" rate and prevent their "build up" in the circulating water as shown in Fig. 1. With the portion of the feed water going directly to the underflow, comes the very fine solids not concentrated by the cyclone. All the larger solids are removed from the feed and delivered in a concentrated condition at the underflow. To apply thickeners with some reasonable assurance that operating requirements will be met, it is necessary to know the rate at which solids of all sizes must be removed from the circulating water and to know the thickener characteristics. The required removal rate of fine solids not recovered by other dewatering devices may be estimated from the size distribution and tonnage of the plant feed with a reasonable allowance for degradation in the circulating water system. A more reliable estimate may be secured by sampling the plant bleed water during a constant load period.

Jan 1, 1952

By AIME AIME

DESTRUCTION of the plants, machines, utilities, tools, materials, and other essentials for peacetime living penalizes not only the owners of the materials destroyed, but the world as a whole. Specifically, the fundamental fallacy of any proposal for the in- discriminate destruction of the German industrial system is that it fails to differentiate between the wartime and the peacetime economy of the Reich. We are for one simple, clear objective-an effective industrial means to keep Germany from starting another war. This objective should not be con- fused, especially before the war is even won, with the appropriate punishment of Germany or with the international arrangements for the long future to be made around the peace table by the representatives of the Allied Nations after victory is achieved. This paper, therefore, does not deal with broad, complex postwar questions of diplomacy and international policy. "Unconditional surrender" implies disarmament of the German armies, the surrender of all arms, munitions, air- planes, and other ordnance material in stock piles or in process. It also should include the elimination of all German war production facilities, such as ordnance plants, munitions plants, and submarine works, and the control of raw materials required by war industries.

Jan 1, 1944

By Samuel Taylor

IF I LIVE another fourteen months and am still con-nected with the coal industry, I shall then have com-pleted a half century with it. Since May, 1874, when .I first entered the bituminous workings as a miner, I think I have held almost every position connected with a mine except possibly that of mule driver, for which I was unfitted by reason of my religious upbringing. We are all agreed, at least I have not heard it contra-dicted, that there is serious over-production in the bituminous industry. This has come about in various ways and is easily explained. During the Fuel Admin-istration, I recall making an estimate of the possible output of the bituminous mines of the country provided they were given a full force of men and a full-car supply; my estimate was a little over a billion tons a year. A few months ago, the late Francis H. Peabody, of Chicago, made a practically identical estimate. If, however, both of these conditions should happen con-currently, there would very soon be no market for the coal, and many of the mines would close down. Even today, if 10 per cent. more cars were furnished, to the bituminous mines, market prices would drop very seriously.

Jan 4, 1923

By Cleland N. Conwell

APPLICATION of seismic methods to the location of buried channels in placer mining is fairly common knowledge, yet some of the facets of seismic refraction surveys have remained obscure in their application to mining. This description by a member of the U. S. Bureau of Reclamation team investigating bedrock at the Oso Dam site, may offer a lead to wider application of the method for bedrock determinations in engineering of mine and mill plants, tailing disposal, and water supply. It may also offer assistance in planning geological exploration in areas covered by overburden. Pertinent, and perhaps more than passingly significant, is that the seismic survey of the Oso dam site started at noon and was completed the afternoon of the next day. Location Oso dam site is on the Navajo River, Archuleta, County, Colo., 30 miles southeast of Pagosa Springs, Colo., 10 miles northwest of Chama, N. M. Bedrock at the proposed dam site is Mesa Verde Formation, Cretaceous age sandstone. The nearest good sandstone exposure is about 5/8 of a mile upstream from the location of the seismic determinations. The material above bedrock is sand and gravel with sandy loam soil covering benches above the river. The site appeared favorable, after a geologic and topographic reconnaissance, but overburden thickness was unknown. Exploratory drilling was not contemplated in the near future so a short seismic investigation was selected as the most suitable method of determining depth to bedrock. Field Procedure Geophysically, a seismic depth investigation is simply the measurement of depth from ground surface to the top of a layer which transmits seismic waves at a higher velocity. In this case the high-velocity seismic layer tentatively correlates with the Mesa Verde sandstone. Field procedure required a seismic explorationline or "spread" with 12 geophones set at measured intervals. Explosive charges were buried at few feet in the ground and detonated at shotpoints near the ends of the spread, and at intermediate points. The time of travel of the seismic waves from the shotpoints through the ground to each of the geophones along the spread was measured and recorded photographically with equipment housed in a field truck. The seismograph on each spread provided a time-travel graph. From it were computed the speed of seismic waves in various layers below the surface and depth to each different seismic layer below the shotpoint. In the case of the Oso dam site it was possible, in addition, to determine the depths below certain geophones, because there were only two seismic layers involved. Interpretation In seismic exploration waves are refracted from the top of layers which often correspond to divisions between subsurface formations. When drill holes are available the geologic logs offer a means of correlating stratigraphic breaks with seismic layers, improving reliability of seismic interpretation in terms of depth to bedrock or other geologic terms. There were no drill holes available in the case of the work at the Oso dam site. Geologic conditions appeared favorable for seismic technique because of excellent contrast in seismic wave velocity between the overburden and the Mesa Verde formation. The upper layer had a velocity of approximately 2500 fps and was interpreted as overburden, the lower layer had a velocity of approximately 9000 fps and was assumed to be the sandstone. These velocities are of the order expected in these materials. The seismographs obtained at the Oso dam site were excellent. The energy from the shot came in strongly at each geophone, giving an easily read record. Time-travel graphs plotted from wave arrival times were uniform and made interpretation comparatively easy. In Spreads 1 and 2 near the river the lower velocity layer was 12 to 15 ft deep. For the spreads on higher ground, or the bench south of the river, it was from 15 to 29 ft deep.

Jan 1, 1952

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council A W Thornton (ISD), Chairman, R W Shearman, Secretary, C S Barrett (IMD), J C Kinnear, Jr (EMD), John Chipman (ISD), J S Smart, Jr (IMD), A W Schlechten (EMD), M E Volin (MED), D S Eppelsheimer (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J J Golden,T D Jones, Evan Just, J C Kinnear, Jr, M Tenenbaum Pacific Northwest Regional Conference E R Marble, General Chairman, Marshall Huntting, Assistant General Chairman, W C Douglass, Mining Chairman, H C Hughes, Mining Chairman for British Columbia, W C Douglass, Mining Chair¬man for United States, Paul Billingsley, Geology Chairman, W D Nesbeitt, Miner¬als Beneficiation Chairman, H D Kelley, Industrial Minerals Chairman, J G Johnston, Metals Chairman, Lloyd Banning, Iron and Steel Chairman, W G Rouillard, Extractive Metallurgy Chairman, E C Roberts, Physical Metallurgy Chairman, D A Pifer, Mineral Industry Education Chairman, Frederick Brien, General Arrangements Chairman Metals Branch Membership Committee C M Squarcy, Chairman, R C Cole, Harold Mar¬golin, M E Nickel, S K Scovil Bylaws Committee A W Thornton, Chairman, W R Hibbard, Jr, J S Smart, Jr (IMD), John Chipman, T S Washburn (ISD), T D Jones, J D Sullivan (EMD)

Jan 1, 1956

By Joseph Bernhardt

THE Cornwall Ore Mines, Division of the Bethlehem Steel Co., at Cornwall, Lebanon County, consists of two separate magnetite ore bodies, approximately one mile apart. The one ore body was an outcrop in which open-pit mining operations were begun in 1742 and continued without interruption. This mine is also served by a shaft for mining that portion of the ore body not recoverable by open-pit methods. The other property had no outcropping and is entirely an underground operation. This mine, cap-tioned No. 4 mine, is serviced by two shafts 220 ft apart. The No. 4 shaft is for hoisting rock and ore, and the No. 5 shaft is for handling men and ma- terials. The shafts are on a catenary curve, closely following the dip of the ore body. Slope of the shafts at the collar is 36", flattening to 26" at the bottom. The footwall at Cornwall is a traprock which varies structurally from solid to highly fractured. Grizzly stations at the top of each chute raise were reinforced by setting timber sills on concrete. Occasionally it was necessary to concrete the entire chute raise. Concreting was done by using 35-yd electric mixers set up in the breaking subs. Sand, stone, and cement were hoisted up through the chute raises to the breaking subs. Late in 1937 it was decided to eliminate chute raises and breaking subs in future development. Haulage levels are 50 ft apart vertically. When ore is below a 40 " dip, slushing drifts are driven normal to the haulages and on 40-ft centers. In a few areas, ore dips greater than 40" and slushing drifts are then placed parallel to the haulage drifts. Finger raises are opposite each other and on 20-ft centers making 20x20-ft draw areas (fig. 1). For loading

Jan 1, 1951