Search Documents

By T. Sterry Hunt

Jan 1, 1882

By John A. Emery

The Pea Ridge iron ore deposit near Sullivan, Missouri, is a dike-like mass of magnetite enclosed in Precambrian porphyries. The ore body tops at the Precambrian surface at a depth of 1300 feet below the present surface and extends to an unknown depth. It dips nearly vertically, intersecting the dip and strike of the enclosing porphyries at an extremely sharp angle. Faulting, both pre- and post-ore, appears to be of minor consequence, and present knowledge indicates that no preferred structural conditions existed prior to emplacement. The ore body is composed of magnetite with specular hematite, quartz, apatite, and pyrite occurring as accessory primary minerals. Specular hematite in appreciable quantities occurs on parts of the cap and the footwall of the ore body. Fresh porphyry breccia is enclosed in the magnetite along the hanging wall and in the western portion of the ore body. Hanging-wall quartz-amphibole and footwall quartz-hematite occur as replacements of certain porphyries. Further alteration has caused sericitization of parts of these zones. The ore deposit is interpreted as having been formed essentially by a single injection of a magmatic differentiate with hydrothermal end phases forming the quartz-amphibole and quartz-hematite portions of the deposit.

Jan 1, 1968

By Charles Jones

Discussion of the paper of CHARLES COLCOCK JONES, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1887 to 1898. D. A. LYON, Salt Lake City, Utah.-For some years I have been interested in the iron-ore deposits of the Pacific Coast, and I feel very much indebted to Mr. Jones for the information he has given us on this subject. I think that we are also very much indebted to him for having presented this paper, as he has given us reliable data in shape of facts and figures, which is just what we need in considering whether or not it would be commercially feasible to attempt to establish an iron and steel industry on the Pacific Coast. Personally, due to lack of market, I do not think it is a commercially feasible proposition at the present time. Mr. Jones states that pig iron can be produced on this coast as cheaply as it can be produced in Pittsburgh. Even. so, what can be done, with it after it is produced? To begin with, iron produced on the. Pacific Coast has to compete with iron produced in China. Last year I had occasion to investigate the subject of the market for iron and, steel on the Pacific slope, and found that it was possible for the producers of Chinese iron to sell it for much less than the price for which iron can be produced in the West, and also for less than eastern pig iron is now sold for, even when shipped through the Panama Canal. I was informed that the agents for Chinese iron had instructions to sell it for $1 or $2 less per ton than that asked for other irons on the market. Of course, I realize that the competition of Chinese iron may not be important, but even if it is not, and even though pig iron ,can be produced at the cost given by Mr. Jones in his paper, I do not see any immediate chance of its being so produced, due to lack of market. C. C. JONES, Los Angeles, Cal.-Mr. Lyon is right. It is a fact that Chinese pig is being sold in San Francisco on some large contracts at $18.50 a ton, while $19 is the usual price. We ought to produce iron. on this coast at $14. Personally I do not think Chinese iron is ever going to be an important factor. It is a bugbear out here now. You are not going to have much Chinese pig iron in .this country. Our little friend Japan is going to absorb everything it can. The price of Chinese pig iron at $18 is about as low as it will ever get. If we can show you that we can produce this iron here at the same price as at Pittsburgh, I. think you will have a good opportunity to compete with anything China or India can ever do. Costs there are very low now. They are going to come up by leaps and bounds in the next few years. The labor cost over there may be very low now, but I. have seen some men from there quite recently

Jan 12, 1915

.MAX ROESLER, Firmeza, Oriente, Cuba (communication to the Secretary?).-It is substantially admitted by all who have recently been in touch with these deposits that the orebodies lie in the fine-grained dark-green rocks, called diorite by most writers and diabasic by myself. The three points of disagreement concern the agency of included limestone blocks as causes of deposition, the agency of the

Jan 5, 1917

By H. D. Attra

The effects of phase behavior on reservoir economics is a function of both fluid composition and flow properties of the reservoir rock. In some operations such as gas injection into volatile crude-oil resertoirs, the stock-tank recovery derived from vaporization of the reservoir oil by the displacing gas can approach the recovery derived from the displacement mechanism. In other cases of gas-cycling reservoirs, the dry injected gas can effectively vaporize a retrograde liquid phase, allowing a substantial reduction in cycling pressure with no appreciable loss in recoverable liquids. Because of these effects, it is essential that phase behavior be considered in developing the economics of any secondary recovery program in which gas is the injected fluid. The inclusion of phase behavior in conventional calculation procedures has been retarded because of the complexity of the calculation and the large volume of laboratory data required. However, by applying high-speed computers and new laboratory techniques, the phase-behavior displacement calculation has been developed to economically include this basic fundamental of gas displacement. The calculation is performed by reducing the reservoir to a series of one-dimensional segments. Phase changes, saturation distributions and changing fluid properties are evaluated for each segment as a function of time. The relative volumes of equilibrium liquid and gas displaced from each segment are determined by a trial-and-error procedure to meet the requirements of phase equilibrium and two-phase flow. The produced fluids are flashed through conditions of surface separation approximating those in the field to obtain actual values for stock-tank liquid recovery and producing gas-oil ratios. Based on the results of successful field studies, the technique appears to have application to reservoirs producing under a nonmiscible gas-displacement mechanism and should substantially increase the reliability of this type of analysis when phase behavior is an important factor. Predicting reservoir performance under gas-injection operations involves three basic principles of reservoir engineering. First, a material balance exists between the displacing gas and the displaced reservoir fluid. Second, the oil and gas flow in relationship with the two-phase flow property of the reservoir rock; and third, phase equilibrium exists between the displacing gas and the native reservoir fluid. To illustrate these three principles, consider the one-dimensional reservoir shown in Fig. 1. The reservoir is divided into a series of segments representing a one-dimensional cross section between an injection area and a producing area. So represents the oil saturation, Cw represents the connate-water saturation and Sg represents the displacing gas saturation. The gas is moving into Segment 1 and the reservoir oil is being produced out of Segment N. Consider the case when gas has just moved into Segment 1 and the displacing gas-oil contact is at position a-a The volume of oil pushed out of Segment 1 is a function only of mobility and the two-phase flow properties of the reservoir rock, that is, Kg/Ko and µo/µg. Behind the front if the injected gas is foreign to the reservoir oil (a nonequilibrium gas), there will either be vaporization of the oil into the gas or condensation of the gas into the oil. In either case the net result is a mass transfer and a re-distribution of composition and liquid and gas saturation. If the displacement is at constant pressure and is continued, the gas moves into new segments, proceeding succesively into Segment 2, 3, etc. The total volume of oil produced from the reservoir

By Carlos G. Valenzuela

The value generally accepted for stacking-fault energy, of copper has been approximately 40 ergs per sq cm based on Fullman's2 value for the coherent twin-boundary energy and the assumption that is twice the twin boundary energy However, Thornton and coworkers8 determined that the lower limit of for copper is approximately 60 ergs per sq cm, based on measurements of dislocation-node radii. They suggested that the assumption of = 2t is invalid. It is the purpose of this note to present results which indicate that the values of obtained by measurement of twin-grain boundary intersections and the values obtained by measurement of dislocation-node radii are actually compatible. The most reliable values for of the a brasses, based on electron-microscope observation of dislocation nodes, are probably those values reported by Smallman and Green6 who applied the Siems correction (1961) to data obtained by Howie and Swann.3 These values shown in Fig. 1 give an extrapolated value of approximately 70 ergs per sq cm for pure copper. In the present work, Fullman's method for determining the stacking-fault energy of copper was extended to the a brasses. High-purity copper (99.999 pet) and high-purity zinc (99.999 pet) were mixed in proportioned amounts and melted in sealed and evacuated quartz tubes. The alloys were homogenized for a week at 750°C and chemically analyzed by means of X-ray fluorescence. These alloys, along with a specimen of pure copper, were rolled to 98 pet reduction and a thickness of 0.009 in., resealed, and annealed for 40 hr at 715°C. Values for the ratio of twin-boundary energy to the grain-boundary energy, it gb, were obtained from measurements of dihedral angles formed at the intersections of twin boundaries and grain boundaries by using Fullman's2 mechanical analogy of surface tensions acting at the intersection of an annealing twin and a grain boundary. The angles between the twin traces and the grain boundaries were measured for a large number of twin-grain boundary intersections at a magnification of X500 using a rotating mechanical stage on a Reichert metallograph. The rotary stage has a calibrated angle scale with vernier so that measurements can be made to 0.1 deg. The mean twin-grain boundary energy and standard deviation were calculated for copper and each of the brasses by the use of an IBM 7072 computer. It was found that the mean value of gb stabilized after approximately 100 twin-angle measurements. This was determined by plotting the mean against the number of angles measured. Since the measured angles deviate from true dihedral angles, a correction factor for grain orientation, discussed below, was applied. The stacking-fault energy was then calculated from these values and the values of grain-boundary energy derived by Taylor.7 The data obtained are tabulated in Table I. Values for stacking-fault energy are plotted in Fig. 1. The value of gb for the specimen of 1.03 pet Zn is close to the value obtained by Fullman2 for OFHC (99.98 pet) copper, 0.045. It is believed that the purity of the copper affects gb significantly. The 99.999 pet purity Cu used in this investigation yielded a value of yt/ygb, 0.76, which is much higher than that obtained by Fullman. Additional evidence suggesting that the purity of

Jan 1, 1965

By Donald B. Gillies

TO me a graduating class of engineers constitutes one ' of the finest inspirations I can imagine. You have finished your four- year scholastic career and are starting out in competition with thou- sands of other young men from other universities to make your mark. Be- cause of your training you men are such an essential part of our present- day civilization that a great weight of responsibility rests on your shoulders, especially at this time, for this is an engineering era. Today, it is the engineer who dreams the dreams and makes our civilization better. It's the engineer who carries those dreams into realization and fulfillment. No matter where we go in business and industry, we find- engineers in key positions, charged with great responsibilities.

Jan 1, 1939

By N. A. Gokcen, J. Chipman

Aluminum and oxygen dissolved in liquid iron were brought into equilibrium with pure alumina crucibles and atmospheres of known H2O and H2 contents to study the reactions: 1—Al2O3(s) = 2 Al + 3 0; 2—Al2o3(s) + 3H2(g) = 2Al+ 3H2o(g); and 3—H2(9) +O = H2O(g). Aluminum strongly reduces the activity coefficient of oxygen and similarly oxygen reduces that of aluminum. Values of the product [% All" • [% O]3 are much smaller than those found in previous experimental studies and are of the order of magnitude of the calculated values. ALUMINUM is the strongest deoxidizer commonly A used in steelmaking, but the extent to which it removes dissolved oxygen has been debatable. The relationship between aluminum and oxygen has not been determined reliably not only on account of the usual experimental difficulties at high temperatures but also because of uncertainties in the analyses of very small concentrations of oxygen and aluminum. The earliest experimental attempt of Herty and coworkers' was followed by a more systematic study of Wentrup and Hieber.' These authors added aluminum to liquid iron of high oxygen content in an induction furnace and considered that 10 min was sufficient to remove the deoxidation products from the melt. Parts of the melts thus obtained were poured into a copper mold and analyzed for total aluminum and oxygen (soluble plus insoluble forms), assuming that the insoluble parts were in solution at the temperatures from which samples were taken. It is conceivable that the furnace atmosphere in their experiments, consisting of mainly air at 20 mm Hg pressure, was a serious source of continuous oxidation and therefore that their oxygen concentrations were correspondingly high. Scattering of their data was explained to be well within the maximum inaccuracy of 10°C in the temperature measurements and errors of ±0.002 pct each in the oxygen and total aluminum analyses. Maximum and minimum deoxidation values, i.e., values of the product [% All' . [% O] differed by factors of 10 to 15; mean values of 9x10-11 and 7.5x10-9 ere reported at 1600" and 1700°C, respectively. Hilty and Craftsv determined the solubility of oxygen in liquid iron containing aluminum, using a rotating induction furnace. Pure alumina crucibles used in their experiments contained the liquid iron which in turn acted as a container for slags of varying compositions consisting mainly of Al2O3, Fe2O3, and FeO. The furnace was continuously flushed with argon, and additions of aluminum and Fe2O3 were made in the course of each experimental heat. The inner surfaces of their alumina crucibles were covered with a substance other than pure Al2O3, containing both iron oxide and alumina. Although frequent slag additions can change the composition of slag in the liquid iron cup formed by rotation, the inner surface of the crucible must depend upon the transfer of oxygen or aluminum through the liquid iron for any adjustment in composition. It is not clear that their metal was in equilibrium with the crucible wall, but it is clear that it was not in equilibrium with Al2O3. Their deoxidation product, [% A].]" • [% O]3, varied by a factor of more than 50; the average values of 2.8x10- and 1.0x10-7 were selected for temperatures of 1600" and 1700°C, respectively. Aside from the experimental determinations, attempts have been made to calculate the deoxidation constant for aluminum indirectly from thermody-namic data. Schenck4 combined the thermodynamic data for Al2O3 and dissolved oxygen in liquid iron by assuming an ideal solution. His calculated values are 2.0x10-15 and 3.2x10-13 at 1600" and 1700°C, respectively. Later, Chipman5 attempted to correct for the deviation from ideality and derived an expression which led to deoxidation values of 2.0x10-14 and 1.1x10-12 at 1600" and 1700°C, respectively. The errors in these treatments originate mainly from inaccuracies of thermal data and uncertainties regarding the activity coefficients of dissolved oxygen and aluminum. The purpose of this investigation was to study the equilibria represented in the following reactions in the presence of pure alumina: Al2O3(s) = 2Al + 3O K = aAl2.ao3 [1] Al2O3(s) + 3H2(g) = 2Al + 3H2O(g) H2O K2 = aAl2(H2O/H2 ) [2] H2(g) +O = H2O(g) K3 = 1/ao (H2) [3] The experimental method consisted of melting pure electrolytic iron, usually with an initial charge of aluminum, in pure dense alumina crucibles under a controlled atmosphere of H,O and H2 and holding

Jan 1, 1954

By G. A. Vissac

MOISTURE in coal must be considered as an impurity, just the same as ash, from the standpoint of utilization of the coal. Being incombustible, it reduces directly the heating value of the coal, and in addition absorbs heat for its evaporation. Its presence means useless expenditures in handling and transportation. In coke plants, extra moisture reduces capacity and may cause damage to brick work and equipment. Accordingly, the removal of extra moisture can be considered just as important as the removal of other impurities, such as ashes, in the modern coal preparation plant. Moisture, which can be removed by heating the coal up to a temperature of 100°C, may be retained in various forms: 1. As a film, on the surface of each coal particle, and in the interstices between particles, retained by capillary forces. 2. Or "occluded" inside the coal particles. This occluded moisture may be either free moisture (as in a sponge), or hygroscopic moisture which varies with atmospheric conditions, (also called "regain").

Jan 1, 1949

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951

By Robert Glass Cleland

WALTER DOUGLAS succeeded his father, Dr. James Douglas, as president of Phelps Dodge in 1916. Before assuming office, the new president had been assayer at Bisbee, superintendent of the Copper Queen, general manager of all the Phelps Dodge mining interests, and altogether had spent a full quarter of a century in various phases of the company's business. Energetic and imaginative, experienced and courageous, he had need of all these qualities before he surrendered the direction of affairs into younger hands, fourteen years later. For the period of his administration was one of sudden ebb apd flow, flush production, drastic curtailment, quick recovery, and near-disaster. In 1917, soon after Walter Douglas became president, Phelps, Dodge & Co., Inc., which had been formed in 1908 as a holding company, went through an internal reorganization for the purpose of simplifying the structure and changing it from a holding company to an operating company. The Copper Queen Consolidated Mining Company, which had the necessary charter power and authority to carry on the business of any and all the subsidiary com-

Jan 1, 1952

By H. R. Thresh, A. F. Crawley

THIS paper reports the results of viscosity measurements on cadmium and indium undertaken as part of a continuing program of liquid metals research at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. For several years this work has continued with support from the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. In the literature, existing viscosity data for cadmium are conflicting and for indium are scarce. To achieve reliable viscosity values, further work was deemed desirable. Viscosities were measured using an absolute technique applied to an oscillating closed right cylinder of liquid metal. The apparatus, constructed in this laboratory, and the techniques involved in its use have been described in an earlier paper.' In calculating viscosity coefficients from the experimental data. Roscoe's2 mathematical analysis was used. Because accurate viscosity determinations are dependent on accurate density data, and since the available data in the literature are conflicting, the densities of liquid cadmium and indium were also determined in this laboratory by a pycnometric technique. This increased the control exercised over all the variables contributing to the accuracy of viscosity measurements. For both density and viscosity determinations, cadmium and indium of 99.999 pct purity were used. These materials were obtained from Cominco Ltd. In order to suppress excessive evaporation losses and help prevent oxidation, a technique developed in measuring the viscosity of zinc' was used for cadmium. This involved maintaining an atmosphere of purified hydrogen in the viscosimeter during the rela- tively long periods while the experimental temperature was changed and stabilized between individual determinations of the logarithmic decrement. Then, immediately prior to a decrement measurement. the viscosimeter was rapidly evacuated to a pressure of about 2 X 10-6 torr. On the other hand. with indium. no difficulties arise from vaporization or oxidation. In this case. therefore. the apparatus was held under a constant vacuum of about 2 x 10-6 torr. When all sources of random and systematic error have been evaluated, the technique is considered to yield data accurate within 10.5 pct. The viscosity of cadmium was measured to a maximum temperature of 451.8°C and that of indium to 346.5°C. These temperatures are. respectively. 130° and 190°C above the melting points. Two separate runs were made on indium. The results are given in Table I and, when plotted. yield the smooth curves evident in Figs. 1 and 2. Values of A and C to fit the well-known Andrade1 equation were determined by a regression analysis. The equation is: where n = coefficient of viscosity. i = specific volume. T = temperature in °K Despite its empirical nature. Andrade's equation has been shown by many workers to describe accurately the temperature dependence of viscosity. During the current research program, this equation has been found to fit the data precisely for all the metals and alloys that have been studied.5,6 The A and C' values for cadmium and indium are given in Table 11. Comparing the magnitude of the present data with those of previous workers,7-10 as has been done in Fig. 1, it is evident that the results of Fisher and Phillips10 deviate markedly from the rest. With the exception of one point from Gering and Sauerwald,7 all other data agree within ±2.5 pct. However, the agreement between the present results and the work of Menz and sauerwald9 is especially good over the entire experimental temperature range. Such agreement may be expected since Menz and Sauerwald's

Jan 1, 1970

World Petroleum Consumption. By V. R. GARFIAS AND R. V. WHETSEL. (Trans, vol 107). A tabulation showing world consumption of gasoline, kerosene, gas and fuel oil, lubricants, and miscellaneous petroleum products by counties in the years 1931, 1932 and 1933 , Totals are given; for instance, Cuba consumed 3,998,000 bbl of all petroleum products in 1933, in 1933; the world consumed 1,366,291,000 bbl. of all petroleum products, etc. Domestic Production. Annual Symposium of Petroleum Division, February Meeting, 1934 (Trans, vol. 107. 181 pages.) The symposium consists of reports on petroleum and gas developments and production in the producing states of the United States. This year the statistical information is presented in a new and far more comprehensive form. The reports on domestic production are as follows: Arkansas, by B C Craft; California, by V H. Wilhelm and H. W. Miller, Colorado, by C. E. Shoenfelt, Illinois, by A H Bell, Indiana, by W. N Logan and P. Simpson; Kansas, by Marvin Lee; Kentucky, Ohio and West Virginia, by V. C Smith; Louisi¬ana, by B C Craft, Michigan, by Theron Wasson; Mississippi, by B C Craft; Missouri, by F C Greene, Montana, by H. N Hickey, New Mexico, by C. E Shoen¬felt and D E Winchester, New York, by D. H. Newland, Oklahoma, by L. G. E. Bignell, J 0 Lewis and E. A Hanson, Pennsylvania, by G H Fancher, Tennessee, by L. C Glenn, Central Texas, by R B. Kelly and P R Martin, East Texas, by A R. Denison, Gulf Coast, by L P Teas, North Texas, by H B Fuqua and B. E Thomp¬son; North Central Texas, by J M. Armstrong, Panhandle, by R H Lynn and T. C. Craig, Southwest Texas, by 0. G. Bell; West Texas, by C W. Reith, Utah, by E S Shaw, Wyoming, by J G Bartram.

Jan 1, 1935

By I. R. Kramer

In his technical note entitled "Specimen Temperature During Electropolishing of Aluminum Crystals" Dr. Nakada 1 reported that the temperature of his aluminum specimen increased 65°C when it was polished electrolytically; he therefore concluded that the temperature of the specimens used in our work (Nakada's Refs. 4 and 5) similarly increased by this amount. From this he further concluded that the change in plastic-flow characteristics associated with the removal of the surface by electropolishing during deformation were due solely to a temperature effect. We believe that these conclusions are not justified. It is, of course, realized that the amount of the temperature increase is associated with the total heat transfer of the entire system, including the efficiency of the stirring action, heat flow through the grip on the specimen, and so forth. Of great importance is the type of electrolyte used for polishing. For example, in Dr. Nakada's experiment a methanol-perchloric acid solution was used. This solution has a relatively low conductivity and for the current densities of 0.3 amp per sq cm the electrical input appears to be 30 to 40 w. In our research a methanol-nitric acid solution was employed and for the size of specimen employed by Dr. Nakada the power never exceeded 7 w. There are major differences in his test apparatus which also appear to affect the temperature rise. In our case a steel specimen holder was used in order to provide a good heat sink and conduction path. The cathode was a coiled aluminum tube through which a coolant was passed to provide additional cooling capacity near the specimen. The stirrer was placed in a position to obtain maximum cooling efficiency. On the other hand Dr. Nakada used a teflon grip to support the specimen at one end only and a flat copper cathode, thus providing a much less efficient heat sink as compared with the metal grips used in our studies. The relationship between current density and the temperature increase for two sizes of aluminum crystals tested in our tensile apparatus is shown in Fig. 1. The temperature measurements were determined from a thermocouple spot-welded to the surface of the specimen. The thermocouple was protected from the acid by means of a thin film of stop-off lacquer which covered just the outer surface of the thermocouple junction. Whereas Dr. Nakada reported a time delay of 8 min to obtain thermal equilibrium, our temperature change occurred in less than 15 sec. This emphasizes the importance of the heat transfer in the entire system. However, readings were taken over a period in excess of 5 min to assure thermal equilibrium. The data given in Fig. 1 were also confirmed by determining the thermal expansion of the specimen in a sensitive creep apparatus. As may be seen, for the smaller specimen the increase in temperature is 8°C for a current density of 1.5 amp per sq in. The majority of our data on the effects of surface removal on the plastic behavior of aluminum were obtained at current-density values at or below this value. Above 1.5 amp per sq in. the temperature rise is uncertain; for under certain conditions, especially in the vicinity of 2 amp per sq in., the anode can become polarized and the current flow is erratic. This condition is easily recognized because wide fluctuations in the creep and stress-strain data make it virtually impossible to obtain reliable results, a condition which was always avoided in our work. The temperature increase for the larger specimen is less than that of the smaller specimens below a current density of 1.5 amp per sq in. At a current density of 2 amp per sq in. the temperature increased 13°C. The above temperature data are in accord with observations made during creep experiments. Using a transducer capable of detecting strain in the order of 10 -6, temperature changes in excess of 8°C were not detected when the current density was increased to as high a value as 1.5 amp per sq in. Finally we wish to point out that our experimental data cannot be explained solely in terms of a heat effect. For example in Fig. 1 of Ref. 2, the change in slope of Stage II as a function of the rate of re-

Jan 1, 1965

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By John Tabor, R. B. Spivey

INTRODUCTION Shafts have been sunk in a number of ways. By and large, however, most have been sunk by drill, blast, muck, and slip form methods. Most methods have provided satisfactory means of completion. The major drawbacks to the conventional methods have been: (1) un- reliable cost estimates for completion; (2) unreliable rates of progress; and (3) unreliable integrity of the shaft lining. Recently , engineering design studies have been done that strongly indicate, that, by the use of existing proven technology, shafts can be completed faster, more cheaply, safer, and with a better lining that has been possible using conventional methods. THE METHOD The alternate method utilizes the techniques of big hole drilling, shield excavator tunnelling, and pre-cast concrete lining. Big Hole Drilling - Drilled shafts have been completed for several years and I don't intend to address the technology, only to point out the use of drilled shafts is an alternate method of shaft sinking. Ideally, in a multi-shaft mine, the first shaft would be blind bored and cased to a size, whereby it can handle the muck from the excavation of subsequent shafts. It should be an 8' to 10' completed diameter. The cost of such a shaft in sedimentary formations compares favorably with a conventional shaft. However, it is much faster. For additional shafts, the role of the drill is to complete small holes (3' to 4') to the desired horizon. This is merely a hole to allow slashing to a larger size with easier muck removal from an underground drift connected to the previously drilled shaft. The smaller holes, just as the larger one, should be cased and grouted into place so as to assure a smooth open hole. SHIELD EXCAVATOR Theory and History - Tunnelling Shields have been in common use for several decades, and steam powered shields were used in England over 100 years ago. The purpose of the shield is to provide temporary ground support, protect personnel during operation, and to house the excavating equipment. The excavating equipment approach has varied from attempts at a continuous or semi-continuous boring machine, the tunnel mole, to a mechanical or hydraulic digging arm. The shield may or may not be an active digging element. If not active, the boring tool or cutter is advanced ahead of the shield to full diameter and then the shield is moved up to the cutter, or the shield advances along with the cutter. If active, the cutter opens a conical free face, and the shield is either jacked forward so that the leading edge spalls rock to the free face or poling plates are thrust forward to spall to the free face. In either approach, various methods of muck removal are incorporated into the shield. These may be gathering arms, conveyors, or with moles, hydraulic transport, where the cuttings are sufficiently fine. The efficiency of the muck removal system is critical as excavation is rapid and the system could easily become muck-bound. Application to Shaft Sinking- Technically, the use of a shield to sink vertical shafts is no different than a tunnelling operation. It is, in fact, less complex in most respects. Muck and water removal are difficult in a blind-driven shaft. However, where an underground opening is available for handling muck and water, rapid shield sinking is possible, using a pilot hole for muck and water to fall through and be removed from below. The Tabor Mining Shield is basically a caisson approach, whereby, the ground is only seen at the face or bottom. It does have hydraulic jacks to force it downward and has segmented cutting edges which allows forepoling ahead of the shield. The hydraulic excavator allows mining in the center of the face around the previously drilled hole with the forepoling segments slabbing to this free face. First, the drilled hole is cased and grouted. The machine is a tube with an excavator. The work cycle is as follows: (1) The casing and grout are cut at predetermined intervals by shaped charges. (2) The casing is crushed by the excavator, removed from the hole and hoisted to the surface. (3) The excavator then rips out a face around the hole by digging the formation in tension and breaking the pieces

Jan 1, 1982

By Allen D. Gorrison

EFFORT to develop fundamental quantitative information and improved technique in the production of petroleum has long been faced with difficulties of a particularly evasive nature, owing to a combination of circumstances. In the first place, petroleum comes from far below the ground, out of sight, so that information derived from indirect observations must be extrapolated to reservoir conditions. If one does not force the analogy too far, the petroleum engineer may be said to be somewhat in the position of the astronomer. The actual phenomena which he wishes to observe in detail appear at a place so deep in the earth?s crust that personal observations and direct experiments are impossible.

Jan 1, 1942

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958