Search Documents

By L. D. Jaffe

IT is now well established that quenched and tempered titanium alloys have much better ductility when the quenching is from a two phase a-B structure, rather than from an all B structure. The corresponding microstructural differences, however, have not been shown in previous publications. Accordingly, specimens were cut from a % in. rod of commercial RC-130A, containing 7.9 pct Mn and 0.12 pct C, which had been previously hot rolled, heated 1 hr at 1100°F, and air cooled. (The same heat has been studied by others." 7 Samples about 1/4 in. cube were heated in helium 1/2 hr at 1450' or 1700°F, quenched in brine, tempered in helium 1 hr at various temperatures up to 1250°F, and quenched in brine. They were then sectioned and metallo-graphically examined, using an etchant of HF-HNO, in glycerine. As quenched from 1700°F, the microstructure observed was clear /3. (Probably also present was U, as the hardness was 400 Vhn, but w is not yet reliably revealed by any metallographic technique.) When the /3 quenched alloy was tempered at a high temperature, a precipitated as a grain boundary film

Jan 1, 1957

By C. A. Heiland

THE investigations described were made on a portion of Clear Creek basin near Golden, Colo. (A portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line II.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.1 Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments.

Jan 1, 1928

By Yap Chu-Phay

ALTHOUGH chronologically, the Sb-Bi system was the first one studied by the writer, the theoretical basis of the equations used in this paper is fully discussed in the writer's paper on the iron-carbon system,1 because he believed that many would be more interested in the iron-carbon alloys. He suggests, therefore, that the reader consult that paper to familiarize himself with the theoretical aspect of the thermodynamic treatment outlined herein. This paper is divided into two parts: Part I deals with the Sb-Bi system and Part II deals with the lead-rich side of the Sb-Pb system. Although the former system has not much practical interest now, it has great theoretical interest in that it, is the one system that for a long time was thought to have (and under specific conditions still has) an anomalous solidus, which no amount of physical investigation could adequately account -for. The latter system of course, is particularly interesting in the lead-rich end. It will be shown that the thermodynamic method is capable of predicting reliably the equilibrium position of the solidus, and thus acts as a check on the experimentally derived solidus.

Jan 1, 1931

By P. K. STRONG

AS an evidence of the fact that mines safety is not being neglected even in the remote district of the Philippines, a short account is appended of the organization and activities of the Mambulao-Paracale District First Aid and Mine, Rescue Association, whose headquarters are at Jose Panganiban Cam, Norte P. I. The second annual miner?s safety celebration which is sponsored by the Association was held in Paracale on Sept. 2, 1940. The event is the big occasion of the year when the thousands of employees of the mines in the district meet to compete for prizes and has become a great social function as well.=

Jan 1, 1941

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICHARD, Vice-Chairman D M LIDDELL Secretary, 7 Wall St.. New York. N. Y. C. A. BORN, Treasurer JOHN V. N. DORR LEWIS W. FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman JAMES G. CARLETON. Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. W. H. LINNEY, Chairman OSCAR LACHMUND, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. STANLY A. EASTON S. SHEDD

Jan 12, 1917

By E. H. Kelton

THE purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for, these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temper,1 having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw.

Jan 1, 1934

By D. P. Koistinen, K. E. Beu

THE application of the integrated intensity X-ray diffraction method to the measurement of retained austenite concentrations in hardened steels has been fully described.'-' In developing this particular method, the assumption was made that the samples used would have flat surfaces which were free from voids and in which austenite was homogeneously distributed. The original calculation procedure' was modified to include the constant factor G which relates the intensity of a given diffraction line to the concentration of the component giving rise to that line. In order to include A (0) in the constant factor G, it was further assumed that the geometrical conditions relating the X-ray beam, camera cylinder, and sample surface were precisely met.V has been demonstrated that these geometrical conditions can be met experimentally without difficulty in many cases;' however, for those samples which have irregular surfaces or where it is impossible to locate the sample in the proper position with respect to the X-ray beam and film cylinder, it is desirable to evaluate experimentally what effect these nonideal conditions have on the reliability of the austenite determination. This note decribes the results of such experiments. SAE 1095 bar stock was used throughout and all samples were heat-treated as follows: 1600°F for 1 hr in a neutral atmosphere, brine quench, and 300°F temper for 30 min. To control heat-treatment conditions as closely as possible, all samples were plated with 0.002 in. copper to protect the immediate surface from the heat-treating atmosphere. After heat treating, the samples were deplated electroly-tically so that only the copper was removed. The heat-treated surfaces thus obtained were nearly as bright and polished as the original surfaces before copper plating although no mechanical work was done on the samples after heat treating.

Jan 1, 1954

By Ernest A. Hersam

The small amalgamation-test of the laboratory is not always reliable as a basis for important decisions as to the character and commercial treatment of ores. The conditions of continuous practice on a large scale are not always reproduced in the brief laboratory-test. Sometimes such a reproduction would be very difficult, or impracticable; sometimes it is not even attempted, and the test is performed in a rough way, without regard to the effects of small variations in the methods pursued. The aim of a laboratory amalgamation-test is to learn how much of the gold or silver in an ore can be economically recovered by amalgamation on a commercial scale. The yield can be increased, perhaps, by additional chemical treatment or by extreme comminution of the ore; but this might cost more than the value of such increase. Moreover, in practice, other operations often follow amalgamation; and these operations may remedy a defective extraction by amalgamation, more economically than could be done by directly increasing that extraction. The test should be performed, therefore, upon a uniformly-sized material, and under conditions that are precisely known and capable of being exactly duplicated, or purposely modified. The crucial feature of the test is the effectiveness of the contact made between the gold or silver of the ore and the amal-gamating-surfme. This may depend upon the temperature; the duration of contact; its force, due to gravity or impact; the hardness, plasticity or liquidity of the amalgam; the roughness or other quality of the amalgam-surface; the scouring action of the ore upon the amalgam, or the suspension and

Jan 1, 1905

By Hugo L. Johnson, Robert Wallace

THE Midvale plant of the United States Smelting Refining and Mining Company consists of a flotation mill for concentrating sulphide ores of lead and zinc by differential flotation to produce three separate concentrates, one of lead, one of zinc, and one of iron pyrite; and a lead smelter for smelting ores and concentrates to produce base lead bullion, The plant, including its shops, laboratories, office, railroad yards which serve both mill and smelter, and areas reserved for tailing ponds and slag dumps, covers 646 acres on the right bank of the Jordan River at Midvale, Utah. It is twelve miles south of Salt Lake City and sixteen miles east of the West Mountain mining district at Bingham Canyon from which is drawn a large part of its ore supply. Custom ores are treated as well as the product of Company mines.

Jan 1, 1948

By Rodolfo V. de la Cruz

The accurate assessment of the in situ deformability of rock masses is very important in the de and construction of underground openings for mining and geotechnical engineering applications. This paper presents a method and device for determining the in situ deformability of rock masses by relating the borehole jack load to the diametral displacements at a number of orientations around the borehole wall. The method called mu1tiple measurement method include the steps in which: a) diametral displacement sensors are installed at different orientations around the borehole to measure the changes in length of various diameters of the borehole; b) a uniaxial load is applied on two opposed octants of the borehole wall, and; c) using elastic theory and assuming a reasonable value for the Poisson's Ratio of the rock mass, the in situ deformability of the surrounding rock materials is determined from the measured diametral displacements and applied unidirectional load. The multiple measurement method has a significant advantage over existing methods since it provides several independent data in a single test from which to calculate the in situ deformability of the rock mass. The multiple data provide a check and counter check on the reliability and accuracy of the various measurements. The multiple data would also provide a means of quantifying the degree of fissuring on the borehole wall. Information on the degree of fissuring is very important in numerical modeling of rock masses.

Jan 1, 1984

By C. H. Mathewson, A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrellce of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below. Conditions of Equilibrium between a Metal and Dissolved Oxide at Different Temperatures and Pressures The general conditions of equilibrium in any system are conveniently summarized in a projection of the triple curves of the P, T, X space

Jan 1, 1935

By Eldon C. Pattee

Variations of a very reliable geochemical field test for beryllium developed by Patten and Ward, have been adapted by the U.S. Bureau of Mines to facilitate rapid testing of reconnaissance samples and to aid in rapid examination of known occurrences. Although several qualitative tests for detecting beryllium have been described in the literature,1,2,3, the Patten-Ward4 morin geochemical field method has the advantages of being rapid and being quantitative for minute amounts of beryllium. In addition to the morin field method, Patten, in cooperation with Griffitts, have developed a contact- print method for determining beryllium in hand specimens.5 The semiquantitative method can be used for rapid screening of samples in exploration or reconnaissance work. The use of beads for fusing samples provides a more rapid test, but gives less accurate results than the method developed by Patten and Ward. The semiquantitative method, however, requires less equipment and combines three stock solutions into one reagent for easy application. Estimates of samples in the range from 3 to 1000 ppm varied from about 0.25 to 5 times the actual beryllium content.

Jan 5, 1965

By E. H. Kelton

The purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temperll having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw. When zinc-base alloys, with their wider ranges of effective rolling treatments, came into increased use, their dynamic ductility and drawing quality appeared to have no connection whatever. Furthermore, comparisons of known drawing quality with other physical properties of the metal, including tensile strength, elongation and dynamic cold bends, were fruitless in yielding any clear relationship. Almost any test value produced in one piece of metal could be duplicated by another rolling or annealing treatment with attendant different drawing characteristics.

Jan 1, 1934

By Willard L. Cumings, Benjamin L. Miller

(Glen Summit Meeting, June, 1911.) I. THE CAMAGUEY DEPOSITS. 1. Location. THE Camaguey brown iron-ore deposit covers the top of San Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name "San Felipe district " is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,1 who says: "The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camaguey City, in the province of Camaguey Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp 2 has the following to say of ores in Carnaguey Province * Geologist, Bethlehem Steel Co. + Professor of Geology, Lehigh University. 1 Bulletin No. 540, U. S. Geological Survey, p. 324 (1908). 2 The Iron Ore Resources of the World, printed by the Eleventh International Geological Congress, vol. ii., p. 795 (1910).

Mar 1, 1911

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By D. R. Hanson

The acoustic vibrational spectra of impacted rock slabs were examined at the Denver Research Center, US Bureau of Mines, in an attempt to characterize the behavior of partially detached mine roof rocks. The ultimate goal of this study was to develop a technique or instrument that could provide a quick, accurate, quantifiable measure of mine roof stability. The power spectra of unstable rock slabs were found to contain more energy in the range of 200 to 1000 Hz than solid rock. Comparison of the power contained between 500 and 1000 Hz with that between 3000 and 3500 Hz provided a quantitative measure of rock stability. A lightweight prototype field instrument was designed, constructed, and field tested. This battery-powered instrument computes the power contained in the two frequency bands, compares their magnitude, and displays a number related to the stability of the block tested. Field tests showed the instrument provided reliable measurements of block stability even under conditions of noise that would have seriously degraded the accuracy of the standard methods of roof sounding.

Jan 1, 1986

By F. C. NINNIS

AT THE Belmont mill, the pregnant solution is de¬livered to a 30 by 10-ft. tank, from which it is pumped to three Merrill clarifying presses of the sluice-bar type, whence it flows through the meter to the precipitation supply tank. ?The solution for precipitation is pumped by a 10 by 10-in. Aldrich triplex pump and delivered through a 6-in. line to the forty-eight triangular frame Merrill presses at the head of the mill. Zinc dust is fed in at the pump suction and the solution precipitated to 0.01 to 0.02 oz. silver. The solution flowing from the presses is tested at 1-hr. intervals with sodium sulfide. All solution is precipitated to the same value; 4J tons of solution are precipitated for each ton of ore treated and the presses are cleaned every 15 days. The product from the presses' is dumped into steel cars having steam-jacketed bottoms, in which they are dried until the moisture content is between 15 and 17 per cent. when 8. per cent. of soda and .3 per cent. of borax are added and the contents thoroughly mixed. In the case of special clean-ups, the precipitate is tested and the flux is added to meet the requirements.

Jan 1, 1921

By F. B. Plummer

GEOLOGICAL engineering as applied to oil fields, or production geology as some prefer to designate the profession, is designed to fill in the border line between pure geology and pure petroleum engineering. Therefore the production geologist may, and frequently does, reach out to grasp much in both professions. Where once the oil geologist was content to pick samples out of a mud ditch and try to identify oil formations from the color or appearance of flakes of rock bailed out of a well, now he has to deal with graphic electrical logs obtained by intricate and highly technical electrical apparatus and to make exact determinations to the fraction of an inch of the depth and thickness of an oil sand 2 miles below the surface.

Jan 1, 1944

By Donald W. Murphy, John Chipman

Recent developments in iron alloys containing nitrogen have indicated that this element may exert a considerable influence on the properties of the metal. This influence is not always in an undesirable direction and the indications are that nitrogen should be regarded as an alloying element, the amount of which should be subject to control, rather than as an inherently deleterious impurity. In controlling this element in liquid iron to the best advantage, it is necessary to have a reliable background of fundamental data pertaining to solubilities, rates of solution and chemical reactions of nitrogen in liquid iron. Obviously, the first step in such an investigation is the determination of the solubility of nitrogen in pure iron, and this has been the object of the experiments described in this paper. The solubility of nitrogen in solid iron has been measured by Jurich,' Sieverts,2 Martin,3 and Iwasé4 and the agreement among the first three inspires confidence in their results. No accurate determinations of its solubility in liquid iron have been recorded though several investigators have obtained approximate results. Strauss6 was able to introduce 0.03 to 0.04 per cent nitrogen into steel by the action of either ammonia or nitrogen on the liquid metal. This was accomplished by Eilender and

Jan 1, 1935