Search Documents

By Samuel B. Christy

As is well known, the ore at New Almaden is cinnabar. Native quicksilver occurs also; but, as a rule, in small quantities only. Pyrite occasionally accompanies the ore. Bitumen is quite common,

Jan 1, 1885

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent 'four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

[Aalde, Kaare, ('40) New Mexico School of Mines, Socorro, N. M. Abadesco, Enrique A., ('39) Univ. of the Philippines, Manila, P. I. Abdul-Ahad, A., ('39) Montana School of Mines, Residence Hall, Butte, Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acker, Voscoe, . ('39) Agricultural & Mech. College of Texas, College Station, Tex. Acosta S., Gonzalo, ('40) Univ. of Texas, Univ. Sta., Box 1785, Austin, Tex. Adams, Albert, ('38) New Mexico School of Mines, Socorro, N. M. Adams, Charles W.,' ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams, Hugh T., Jr., ('39) Univ. of Oklahoma, Norman, Okla. Adams, Jack L., ('39) Univ. of Oklahoma, Norman Okla.]

Jan 1, 1940

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1892, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 20 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1892 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By C. B. Alcock, R. G. Hudson

Sulfur pressure measurements above FeS in equilibrium with iron have been carried out by the Knudsen orifice method. A comparison is made of the weight loss of the cell per unit time obtained in the above experiments, that calculated from Richardson and Alcock's measurements of the S2 pressure above FeS in equilibrium with iron, and the dissociation constant for diatomic sulfur from spectroscopic and thermal data. EXTENSIVE equilibrium measurements have been made to determine the sulfur potentials of a great many systems of metallurgical interest.' In order to confirm their reliability, to supply data which may be of use in further thermodynamic calculations, and to establish the reliability of the Knudsen orifice in obtaining accurate thermodynamic values at high temperatures, the present investigation on the pressure of the gaseous species above FeS in equilibrium with iron has been carried out. The Knudsen orifice method has been used for these pressure measurements. Experimental The apparatus and general technique for this investigation are the same as that reported for the determination of the vapor pressure of silver.' To reduce the residual gas pressure in the evacuated chamber, a titanium getter, maintained at run temperature, was introducbed. Several types of Knudsen cells were used—platinum, zircon, and fused silica. The orifice in the zircon cell was fashioned with a small diamond wheel. The same precautions were used in this investigation as were employed in the work on Mo2S2.3 The FeS-Fe mixture was prepared by heating a sample of pure FeS,, supplied by K. K. Kelley of the Bureau of Mines, with excess iron powder, cp grade, obtained from the Fisher Scientific Co. These two substances were heated in a closed Armco iron crucible at 960°C, held in a vacuum of less than 10" mm Hg for 24 hr. The mass was then removed from the cell and ground in an agate mortar. In this form it was charged to the various Knudsen cells. Heating the Knudsen cell for an additional two days was sufficient to obtain constant rates of weight loss of the cell. The data obtained in this investigation are recorded in Table I. To establish whether or not a sulfide of iron is volatile at these temperatures, 0.7646 g of the FeS-Fe mixture, described above and containing 69.2 pet Fe, was placed in the zircon Knudsen cell. Run Nos. 103 to 109 were performed on it. After the completion of these runs, the total amount of iron left in the cell was obtained by chemical analysis. It contained 0.537 g Fe, compared to 0.529 g in the original charge. Thus, there was an apparent gain in iron of 1.5 pet. This is attributed to unknown experimental error, and the conclusion is that no sulfide of iron is volatile. The vapor pressure of pure iron4 is about one thousandth that of the sulfur pressure' at these temperatures. The vapor pressure of iron inside the Knudsen cell will be almost exactly that of pure iron, since in the iron-rich phase the percentage of sulfur is of the order of 0.025 pet.At this low percentage of sulfur Henry's law is probably obeyed by the sulfur. Thus, the iron will obey Raoult's law. In any event, the vapor pressure of iron will be lower than that of pure iron and, since the vapor pressure of pure iron is negligible compared to the pressure of sulfur, the weight loss of the cell due to the vaporization of iron should be negligible. Since neither iron nor FeS is volatile to an appreciable extent, the total weight loss of the cell must be due to the vaporization of sulfur. Discussion and Calculations On the assumption that S, is the only gaseous species present in appreciable quantity, its pressure

Jan 1, 1957

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

CONTENTS PAGE Need for Research in Foundry Pig Iron. By Richard Moldenke. (With Discussion) 1 Carbon Characteristics of Copper-bearing Pig Iron. By W. B. Coleman. (With Discussion) 12 A Pig Iron, Low in Total Carbon, is in Demand for Use in Various Industries. By Enrique Touceda. (With Discussion) 24 Carbon in Pig Iron. By Ralph H. Sweetser. (With Discussion) 28 Second Session (Discussion) 37 Need for Research in Foundry Pig Iron BY RICHARD MOLDENKE,* WATCHUNG, N. J. So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and, for the

Jan 1, 1927

By James M. Barker

Sulfur is a nonmetallic element of great physical and economic importance to the world. It is widely but sparingly distributed throughout the hydrosphere, lithosphere, and biosphere. Sulfur is the tenth most abundant element in the universe and eighth most abundant in the sun. In the earth's crust, which is mainly igneous, it ranks 14th, but is eighth or ninth in sediments (Kaplan, 1972; Stanton, 1972). It apparently is very abundant in the core of the earth, because it is a strong chalcophile, and it is fifth in abundance in stony and iron meteorites (Field, 1972) where it occurs as trolite (FeS). In ancient times sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Shelton (1979) summarized most of the common definitions of terms, grades, and specifications for the sulfur industry as follows (with minor additions): Sources of Sulfur: Combined sulfur-Sulfur that occurs in nature combined with other elements. Cupriferous pyrites-Pyrite containing relatively minor amounts of copper sulfide minerals. Hydrogen sulfide-A toxic gas (H2S) occurring in natural gas and petroleum. Involuntary sulfur-Sulfur produced primarily as a result of legislative or process mandates. Native sulfur-Sulfur that occurs in nature in the elemental (uncombined) form. Nonferrous metal sulfides-Copper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfurs-Complex organic sulfur compounds occurring in petroleum, coal, oil shale, and tar sands. Pyrites-Iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfurs-Sulfur in anhydrite and gypsum. Voluntary sulfur-Sulfur produced in response to market forces. Basic Sulfur Products Produced and Marketed: Acid sludge-Contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-Synonymous with crude sulfur. Bright sulfur-Crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-Solid crude sulfur crushed to -8 in. Byproduct sulfuric acid--Sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-Commercial nomenclature for elemental sulfur. Dark sulfur-Crude sulfur discolored by minor quantities of hydrocarbons ranging up to 0.3 % carbon content. Elemental sulfur-Processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-Elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-Elemental sulfur produced from native sulfur sources by the Frasch mining process. Hydrogen sulfide-Associated with natural gas or petroleum and produced at refineries and coke oven plants; used to make sulfuric acid or recovered sulfur. Liquid sulfur-Synonymous with molten sulfur. Liquid sulfur dioxide-Purified sulfur dioxide compressed to the liquid phase. Molten sulfur-Crude sulfur in the molten phase.

Jan 1, 1983

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By Jack A. Simon, M. E. Hopkins

GENERAL GEOLOGY Coal is defined as a combustible rock that had its origin in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the somewhat unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks being returned to earth will, we hope, provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust of the earth is not completely stable, and throughout the geologic past portions of the crust have moved laterally and vertically. Even today, many coastal areas are slowly rising or sinking. More sudden earth movements are recognized by the earthquakes they cause. Throughout geologic history, rises in sea level or the sinking of the land areas have many times permitted the oceans to cover much of what are now the areas of the continents. Only relatively small parts of the present continents appear to have been above sea level throughout geologic time. Great

Jan 1, 1973

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By A. G. Gilbert

Paradoxical is the word. The coal industry, despite reach- ing a 22-year high in production (590 million tons), has been tagged as having its back to the wall vis-a-vis its valiant attempts to quench the nation's still unabated craving for coal. What must be even more reassuring to the industry, infected once with rumors of a uranium takeover, is a nation's almost insatiable appetite for electricity. Between 1967 and the summer of 1970, utility stockpiles were being gobbled up, diminishing to 79% of the January 1968 level.

Jan 1, 1971

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937