Search Documents

By B. H. Caudle, A. B. Dyes

In a recent publication' it was shown that wells with a free surface in a homogeneous gravity-drainage reservoir have a hyperbolic decline with index n '. This paper reports efforts to extend this theory to practical field cases. As a first step in making the extension, a large number of lease production curves from gravity-drainage fields in the stripper stage were fitted with the general hyperbolic decline equation, q/q, = 1/(1 + y) y and n in each case being determined by statistical methods. It was found that this equation is reliable for decline curve extrapolation for periods up to at least 25 years. The resrilts obtained were disturbing in the sense that values for the index, n, were often smaller than one, which fact leads to the prediction that a well would produce all infinite amount of oil in infinite time. A theoretical investigation based on the results of the previous paper provides a suitable explanation for these low values of n. It suggests that these are obtained if production occurs from two or more layers of diflerent permeabilitv and thicktress or two lnyers having different skin effects. It is predicted that as the more permeable layers are exhausted, the index of decline, n, will rise from a value smaller than 2, to n = 2. A practical method is given for fitting the general hyperbolic decline Eq. 6 to production decline data. When this method is used, the index of decline observed in gravity-drainage reservoirs in the stripper stage when wing only data over early years 01 decline usually agrees quite closely with that determined using data over 25 years or more. This indicates that the hyperbolic decline equation is reliable for predicting behavior of such reservoirs. A method is also suggested for taking into account any changes in the value of the index INTRODUCTION As a result of both experimental work with models and theoretical deductions, it was recently concluded' that wells having a free surface in a homogeneous reservoir producing by pure gravity drainage should have a hyperbolic decline with n = 2. The present report details efforts to extend this work on ideal homogeneous reservoirs to actual field cases. It should be remembered that both the previous work and the present extension are based on the assumption that the reservoir is at very low pressure, and hence, nearly all the potential available for driving fluid to the well is the gravity head. Attempts to apply conclusions of this study to reservoirs which have considerable pressures supplementing the gravity drive may lead to difficulty. WELLS WITH NO FREE SURFACE In a dipping gravity-drainage reservoir such as that shown in Fig. 1, some of the down-dip wells have no free surface. The previous study' showed that the up-dip wells, which have a free surface, should follow Eq. 1. The following approximate analysis, of a type which was justified experimentally for up-dip wells in the work just mentioned, leads to results for the down-dip wells.

By Richard Schellinger, Ronald H. Carlson, Robert D. Norris

INTRODUCTION A very important key to the success of an in-situ leach venture is proper choice of well field chemistry, in which type and concentration of oxidant plays a significant role. For proper design of well field and plant, an engineer must be able to estimate uranium production levels and their change with time. The rate controlling step in the uranium leach process is generally acknowledged to be the oxidation step (Goddard and Brosnahan, 1980; McKnight and Anthony, 1979; Mays, 1979). Uranium head grade is very dependent upon concentration of oxidant injected into the ore zone. If oxidant levels are too low, uranium production requirements will not be met; if levels ate too high, excess oxidant will be wasted in side reactions with gangue material and leach economics will suffer. To date, no reliable laboratory technique exists for generating data easily translatable to field conditions. Empirical correlations based upon lengthy field testing have been the major tools avail- able to the design engineer to date. During the past five years, FMC has developed lab- oratory techniques for studying uranium leach chemistry under conditions simulating as closely as possible the field situation. Both agitated batch and consolidated core leach procedures have been developed. Results of FMC agitated batch studies are described in detail in a companion paper (Carlson, et. al., 1980). This paper will focus on the technique developed for leaching consolidated undisturbed core under simulated down-hole conditions. Through use of a follow-up computer model (Winkley, 1980), generated data can be translated to expected field response, thus providing the design engineer with valuable information in a relatively short period of time. CHEMISTRY In addition to uranium (+4), other oxidant-consuming species present in uranium ore are iron sulfides and carbonaceous material. Iron sulfides are usually present in concentrations far exceeding those of the other two materials and, therefore, represent the major oxidant-consuming species present in uranium sandstone ore. Previous studies (Carlson, et. al., 1980) have shown that iron sulfides exist in both Texas and Wyoming ores as a mixture of pyrite and marcasite (FeSz); furthermore, uranium mineralization (existing as uraninite) was shown to exist as a fine granular material coating or imbedded in iron sulfide crystals and sand grains (i.e. quartz and feldspars). The leach chemistry of a uranium ore body can be described by the following equations using hydrogen peroxide (Hz021 as oxidant:

Jan 1, 1980

By V. C. Smith

Reliable and detailed statistical data available for Kentucky, Ohio and West Virginia are the most meager and unsatisfactory of any of the producing states. Detailed histories and statistics are available for only a few pools. The antiquity of these pools, loose nomenclature, particularly where several names are applied to the same pool or various parts of the pool or a new namsed when the pool was rediscovered, made the collection of accurat historical and statistical data almost impossible. So many of the data reported are unreliable that a breakdown by pools or even by counties, until more accurate information is available, would lead to gross errors. Rather than perpetuate inaccuracies, we have endeavored to go to original sources wherever possible, sift these and provide data that may serve as an incentive and basis for future work. The necessity for accurate information is thoroughly recognized by the operators, particularly because of the effect of recent government regulations and request? for data in connection with the preparation of the various codes a pending legislation. Producers, both major operating companies and individuals, . freely given their time and assistance in the compilation of these data. Valuable information was obtained from tax records, rate cases, statistics published by the oil and gas publications and the Bureau of Mines. So many individuals cooperated in the preparation of these data that individual credit cannot be given. Undoubtedly many errors will be found. Some of the data are open to controversy, and many have been omitted in the hope that new information of a more reliable character may become available. Other omissions are due to an inability to contact the proper individuals, many of whom are no longer connected with this industry. Pennsylvania grade crude sold in 1933 for the lowest price since 1895. Gas production could not find sufficient new markets to fill the void left by industrial stagnation. In the gas industry, where the market price is fixed by contract, uncertainty persisted because of impending legislative action affecting both taxes and utility rates. As a result of these factors and a lack of new money, drilling was restricted to a new low. The lifting of proration toward the end of the year in the Pennsylvania

Jan 1, 1934

By C. R. Johnson, R. A. Greenkorn, L. K. Shallenbarger

This paper describes a study, based on core data, of the directional permeability of a sandstone reservoir. Directional air permeabilities are explained and correlated with lithology by the tensor theory of permeability, which is extended to the more general case of heterogeneous anisotzopic porous media. In this case, the permeability tensor is made up of two components: (I) anisotropy (variation around a point) which correlates with bedding, and (21 heterogeneity (variation from point-to-point) which correlates with grain size. INTRODUCTION Previous studies of directional permeabilityl.5-8 have concerned themselves only with anisotropy at a point, rather than with both point-to-point differences and local anisotropies. In this paper, we present the existing tensor theory of permeability for anisotropic porous media and then extend it to the more general case of heterogeneous anisotropic porous media. The laboratory measurements of directional permeability are explained in view of this extended theory and the data are discussed in terms of the lithologic factors that correlate with it. The results show what the heterogeneity and anisotropy of the reservoir element are, and that the directional permeability correlates with lithology. Data used in this paper are measurements of air permeability in eight directions, spaced at 45° intervals, on 142 2-in. vertical plugs from 30 cores. The core data are meaningful in terms of directional permeability because the cores were oriented to within 45O during drilling and coring.3 Although we initially thought that only 60 per cent of the core material was reliable, subsequent study showed that almost all of it was reliably oriented. After determining the air permeabilities, the data were reduced to three independent variables for each plug: the major and minor permeability axes, and the direction of the major axis. These were obtained by converting the permeability data to the reciprocal square root of permeability and fitting the transformed data with ellipses according to the tensor theory of permeability.8 The point-to-point areal variation of the minimum permeability axis is related to grain size. The direction of the permeability axes, where the major axis exceeds the minor axis by at least 5 per cent (measured variation is about 4 per cent), correlates with the bedding. The permeability tensor used in this study must be considered as the sum of a scalar and a tensor, with the scalar being the minor axis permeability as a function of position, and the tensor the directional effect, which is additive permeability over the minor axis. In this case, the point-to-point variation or heterogeneity (minor axis) is substantially larger than the variation at a point or anisotropy. It may be important that this separation of "directional permeabilities" be recognized when considering migration of fluids due to permeability variation. Local migration may be due to anisotropy and point-to-point migration may be due to heterogeneity, but the direction and magnitude of these may not be the same. Furthermore, in truly heterogeneous systems, one would expect that anisotropy would be the smaller of the two effects. THEORY TENSOR THEORY OF PERMEABILITY FOR ANISOTROPIC POROUS MEDIA8 Darcy's law for flow in porous media in its usual form is where qis the flow rate vector, k is the permeability, is the viscosity, is the vector differential operator, and P is the Pressure. Consider flow, q, through a unit area in the direction of the unit vector n from elementary flow tubes parallel

Jan 1, 1965

By G. H. Fancher

Improving economic conditions are reflected in the statistical picture of the petroleum and natural gas industry for 1933. Prices were better, demand was greater and the volume of production increased. The increase in the production of gas has been due mainly to the utilization of outlets to the new prolific gas fields of Potter and Tioga counties; of oil, to the growing demand for Pennsylvania grade lubricants. It should be emphasized that nowhere is volume of production more subject to control due to the extensive use of secondary methods of recovery and regional peculiarities than in Pennsylvania. A summary of developments in production for Pennsylvania in 1933 of necessity is brief. The data listed in Table 1 are all too few in number and not all that is desirable from the standpoint of accuracy. No state agency for the collection of data exists, no reports are compulsory. Nevertheless, because of the hearty cooperation of many individuals and public spirited corporations, it is believed that the data are as reliable as are obtainable at the present time. Furthermore, records of the past too often are lost, were never in existence or are fragmentary, to say the least. Illustrative of the condition is the fact that no thorough study of the oil and gas-producing regions has ever been made. The publications of the Pennsylvania Topographic and Geologic Survey upon the subject are noteworthy and valuable, especially the most recent one.' The Survey has been handicapped in the work by lack of time, personnel and funds in addition to the difficulties mentioned previously. It is obvious, therefore, that Table 1 cannot be completed for Pennsylvania. The data simply are not in existence. Officially there are 328 oil and gas pools or fields known by name and 58 distinct sands or horizons, one or more of which are productive of oil and gas in the various pools, but reliable data for only three general regions could be assembled.

Jan 1, 1934

By C. W. Binckley, F. R. Burgess, E. R. Haymaker

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962

By R. S. Dean

PROCESSES for the direct production of iron and steel from ores are hardy perennials, and new processes and revivals of old ones are continually being brought to the attention of the investing public if not to the attention of metallurgists. Direct production of iron and steel is so simple that it offers a fertile field for the promoter. Unfortunately in this way direct processes have acquired a bad name, not always deserved, with conservative capitalists and metallurgists. Direct processes cannot, except in special instances, be looked upon as a substitute for any single operation in present iron and steel practice but must be considered, as one link in an entirely new chain of metallurgical process from ore to finished steel. Thus it is, in my opinion, inadvisable to consider the use of sponge-iron processes as a means of treating ore of ordinary blast-furnace grade to produce open-hearth feed. In time I think it will be found equally inadvisable to smelt iron-ore concentrates in the blast furnace.

Jan 1, 1935

By J. E. Walstrom

While intensive research continues to promote a more complete understanding of the potential and resistivity measurements that comprise the electric log, it is believed that consideration should also be given to translating these numerous and often widely separated findings into a coordinated and readable body of fundamental facts designed specifically for the petroleum engineer and geologist. Although provision is made through publication for a ready exchange of new theoretical concepts. it is also desirable to provide reviews and appraisals of the more established techniques and methods from the operating standpoint so that an economic and practical application may be realized concurrently with the theoretical progress. With these basic premises as a guide the author reviews the presnt state of electric log interpretation. The paper is directed not so much to the logging or research specialist as to the petroleum engineer and geologist to whom the electric log is only one of the many tools which he employs. Frequently, these persons do not have the time to follow in detail the many specialized contributions that appear and, as a consequence. are not in a position to place these contributions in proper relation to each other, or to the art as a whole. The paper reviews the basic steps in making quantitative determinations from the electric log of the amount of oil or gas present in subsurface formations and also discusses the degree of reliability of these determinations under various conditions. The paper also indicates the trend of future developments in electric logging systems and methods of interpretation. INTRODUCTION The electric log has been used about 20 years as a means for studying the formations penetrated by a well bore. The first half of this period is characterized by the development of suitable logging techniques and equipment. Although progress in this direction is continuing at a satisfactory rate, the last ten years are characterized more by an increasing interest in methods of electric log interpretation. During this period, a large number of fundamental papers have been published, expounding various logging techniques and particular phases of the interpretation problem. Many of these papers represent important contributions, and a few are classic. This paper is an effort to outline as concisely as possible and in simple terms the main course of progress in electric log interpretation. More specifically, it is the purpose of the paper to review the necessary elements and basic steps used in making quantitative determinations of water saturation from the electric log; and to point out the degree of reliability of these determinations under different conditions. It is strongly advised that the operating staffs of the drilling and exploration departments of oil companies cooperate wholeheartedly with both the electric logging service companies and research organizations in the testing and development of new logging systems and interpretation methods. One purpose of the paper is. however, to indicate the degree of caution which must be exercised in placing confidence in new techniques and interpretation methods that have not been thoroughly tested in the field. It is entirely possible to be cooperative in trying new methods and yet reluctant to believe in the results until the methods are firmly established. It is important to define the meaning of quantitative electric log interpretation. In the most general sense, an interpretation of the log has been made when the electrical characteristics of the formations, as portrayed on the log, have been translated into terms describing the formation geometry, rock type, or any other physical characteristics of the formations. The determination that the top of a sand is at a certain depth is an interpretation of the log. Structural determinations made by correlating electric logs from a given area are also interpretations of the logs. The term quantitative interpretation, however, will be used in this paper in the restricted sense to indicate the determination of the water saturation of a formation. This determination defines the fluid content of an oil and gas productive formation only if the porosity is known, and it assumes that the remainder of the pore space contains hydrocarbons. This assumption is believed to be true for most oil and gas productive formations. The quantitative electric log interpretation may he said to be a determination of the fluid content only to the extent which the water saturation, under the conditions given above. defines it. THE BASIC STEPS The fundamental steps in calculating water saturation from the electric log are: 1. Determination of the true resistivity of the formations from the apparent resistivities as recorded on the electric log.

Jan 1, 1952

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,',' Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By G. B. Thomas

Several methods of analyzing pressure build-up data in wells have been presented by various authors. This paper reviews the theory and method of D. R. Horner and presents example calculations performed on data obtained by testing several different types of wells. These calculations include, (1) graphical estimation of final static pressure, (2) determination of the productive capacity of the pay away from the well bore and. (3) the degree to which the formation adjacent to the well bore has been damaged by completion or other causes. The methods of testing and precautions which should be taken to assure the best data possible are discussed. Limitations and reliability of calculated results are also treated. INTRODUCTION Pressure testing of wells is generally limited to the determination of producing and static mean formation pressures. The so-called "static" pressure determination.. along with PVT, electric log and production data, enable the reservoir engineer to determine, within reasonable limits, the drive mechanism of the reservoir and in some cases. the amount of edge water encroachment. Producing pressure tests enable calculation of productivity indices and allow the engineer to plan the systematic production of a pool for optimum conservation of suhsurface energy. The radial flow formula advanced by Muskat' has been based on the assumption of incompressible radial fluid flow. It has been known that reservoir fluids do not behave in an ideally incompressible manner. For example, incompressible flow theory indicates a simple logarithmic relationship between the difference of the instantaneous and static well pressures when plotted against time. 'The latter stages of this type of plot of pressure build-up data generally show a marked devia-, tion from the earlier straight line trend. which deviation may be shown to be due to the compressible flow of fluids toward the well bore. Shut-in times of 24, 48. 72. or at most 96 hours are currently in wide use for determining so-called "static" reservoir pressure. Due to the continuation of compressible flow of fluids into the well bore long after this arbitrarily taken shut-in time, the determination of static pressures has almost invariably resulted in lower than equilibrium values. Materials balance calculations made early in the life of a reservoir often result in a calculated reserve which later observations prove to be too low. Failure to obtain reliable "static" reservoir pressures within the prescribed 24 or 48-hour build-up period has undoubtedly been a major factor in obtaining these low estimates. Comparison of theoretical and actual productivity performance has indicated that formation damage and not being able to attain true static pressures have been partially responsible for the observed discrepancies. Research into the theory of compressible flow behavior has resulted in methods of applying these theories to the testing of wells. Application of the developed theories to pressure build-up performance indicates that in many cases the following can be estimated. 1. The static reservoir pressure. 2. The in-place effective formation permeability away from the well bore. 3. The degree or extent by which the formation has been damaged adjacent to the well bore, either through completion methods or subsequent damage due to fluid entry. REVIEW OF THEORY Horner2 has shown that the pressure build-up within a "point source" well is approximated by the following formula: Equation (1) is the approximate "point source" solution to the radial compressible flow equation advanced by Muskat. The solution assumes the following: 1. A point source well is producing at constant rate from the center of an infinite reservoir with a constant pressure at its external boundary. 2. The fluid flowing is present in one phase only. 3. The compressibility and absolute viscosity of the fluid remain essentially constant over the range of temperature and pressure variation encountered. 4. The well i.; shut-in at the sand face arid there is 110 after production into the well bore. 5. The formation permeability is homogeneous in the direction of flow. From Equation (1) it can be seen that if an ideal well were shut-in while producing from a reservoir under the conditions assumed, the pressure build-up would be a logarithmic func-

Jan 1, 1953

By B. C. Allen, R. I. Jaffee, D. J. Maykuth

Wrought unalloyed iodide chromium, containing 39 to 95 ppm total interstitials, has a tensile transition temperature of —15°C. Re crystallizing at 1100°C causes the transition to rise to 90° to 390°C, depending on the purity, grain size, and cooling rate after annealing. At about the 100 ppm level, individual additions of carbon or nitrogen raise the transition of both wrought and recrystallized chromium by as much as 210°C, while oxygen has a lesser effect, and sulfur essentially no effect. High transitzon temperatures are exhibited by recrystallized and quenched chromium, and appear to be associated with the amount and distribution of inter-stitials. The latter cm be either in solid solution or in the form of precipitates within the grains or at the grain boundaries. Quench hardening in chromium is primarily caused by nitrogen. The hardness, re crystallization, and grain growth behavior of chromium with and without impurity additions were also investigated. BECAUSE of low density and good oxidation resistance, chromium-base alloys are potentially useful for elevated-temperature applications. The main deterrent to the use of chromium in structural applications is its lack of low-temperature ductility, especially in the recrystallized condition. Accumulated evidence has shown that the ductility of chromium is sensitive to purity. The objective of the current study was to determine the effect of common nonmetallic impurities on the tensile properties of high purity chromium. The separate effects of carbon, oxygen, nitrogen, and sulfur additions on the ductile-to-brittle transition were evaluated for wrought and recrystallized material after various cooling rates. EXPERIMENTAL WORK Unalloyed iodide chromium and seven impurity alloys containing individual carbon, oxygen, nitrogen, or sulfur additions were prepared in rod form. Nominal additions were 100 ppm C, N, and S, and 100 to 500 ppm O. The additions were about a factor of ten greater than the residual amounts in the unalloyed material. The seven alloys and two unalloyed compositions were consolidated into four-pound ingots by conventional consumable arc melting of pressed and welded electrodes under 0.5 atm of helium. Impurity additions were made to the electrode in the form of crushed master alloys. The impurity alloys were double melted to improve homogeneity. The ingots were broken down by extrusion at 1200°C in evacuated steel cans at a reduction ratio of 18 :1, using a molten borosilicate glass lubricant and a ram speed of 80 in. per min. The cans were removed by acid pickling, and the chromium core ground free of surface undulations. Cut lengths were sheathed in mild steel and swaged at 900°C until the core was about 1/4 in. in diam. Two additional 15-lb ingots of unalloyed chromium (ICr-3, ICr-4) were prepared by arc melting and broken down by 26:1 extrusion at 1250°C without a steel can. The billet was lubricated and protected from contamination by a coating of molten glass. The resulting extrusion was then sheath swaged as described previously. Representative chemical analyses of each of the materials, after removal of a 10-mil surface layer

Jan 1, 1963

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,' through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By E. N. Harshman

Uranium mining and milling are rather new industries in Wyoming and South Dakota, but, in the past 15 years, ore valued at more than $400,000,000 has been mined and milled in the region. The major uranium deposits are in structural and/ or erosional basins or on the flanks of uplifts. The principal host rocks are medium- to coarse-grained sandstones that were deposited in continental or brackish-water environments and were derived in large part from the granitic cores of the uplifts and the sedimentary rocks that flank the cores. The ages of the host rocks range from Cretaceous to Miocene, but more than 95 per cent of the known reserves in the region are in rocks of early Eocene age. The bulk of the ore in the region is unoxidized and lies below the water table; some oxidized ore has been mined in the Powder River Basin and Black Hills districts. The unoxidized ore comprises pyrite, uraninite and/ or coffinite, marcasite, hematite, jordisite(?), and selenium. Minerals in the oxidized ore include hydrous uranium carbonates, phosphates, and sulfates and hydrous uranium and/ or vanadium silicates. The deposits are in the form of ore rolls that contain from a few hundred to a few hundred thousand tons of ore, ranging in grade from 0.1 per cent to 1.0 per cent U3O8. The rolls are at the margins of large tabular bodies of sandstone that has been altered by the orebearing solutions. The deposits are believed to have resulted from the interaction of an alkaline; oxidizing, ore-bearing ground water and a reducing environment. Exploration guides include the spatial relations of ore to altered sandstone, favorable lithology in the host rock, the content of certain elements and/ or compounds in ground water, and the relation of deposits to major paleodrainages.

Jan 1, 1968

By P. C. J. Gallagher

A number of recmt determinations for the ratio of extrinsic to intrinsic stacking fault energy in fcc solid solutions are examined. Some of these arise from incomplete analyses which can yield only approxi?nate values for the ratio. Reliable results, on the other hand, obtained using extrinsic-intrinsic fault pairs, show that the extrinsic and intrinsic fault energies are essentially equal in several materials. There is some reason to believe that this finding is of general applicability to fcc elements and alloys. A wide range of values has been obtained for the relative magnitudes of the extrinsic and intrinsic stacking fault energies (yext and yint, respectively) in recently published studies in a variety of materials. In contrast, Hirth and Lothe' using a central force model have shown that out to tenth nearest-neighbor interactions the perturbation in energy caused by both types of fault is the same. Although the model used is not completely valid in metals, there is nevertheless some indication that marked variations of yext/nnt should not be observed from one material to another. In early work in Cu-A1, Cu-Ge, Ni-Co, and stainless steel all the deformation faults observed in the electron microscope were found to be intrinsic in nature, which led to an attitude that the extrinsic fault energy must be considerably greater than the intrinsic. Extrinsic faulting arising from deformation has, however, more recently been directly observed in Au-4.8 at. pct n;~ Ag-6 at. pct Sn and Ag-8 at. pct sn; Ag-7.5 at. pct In and Ag-11.8 at. pct 1n;"' pure silwer and Ag-0.5 at. pct ~n;' and Cu-22 at. pct Zn, Cu-30 at. pct Zn, and Cu-7.5 at. pct ~1.l' Multilayer loops containing extrinsic faulting have also been observed in quenched aluminum." While peak asymmetries in X-ray faulting probability studies were generally attributed to the presence of twins,Lelel2 has recently reinterpreted earlier X-ray data in Ag-Sb alloysU in terms of the presence of extrinsic faulting. The determinations of yeXt/yint made from the above studies are shown in Table I, with a brief description of the techniques employed. A number of the methods utilized are deficient in one or more respects, and the reliability of the values listed will be discussed. ~ele'~ recognizes that his approximate determinations of yext/yint assumes equal numbers of extrin-sically and intrinsically faulted dislocations. It is well-known, however, that such an assumption is not at all justified since extrinsic faulting has but rarely been observed in samples studied in the electron microscope. The only conclusion that should be drawn from the X-ray results at present is that the total intrinsic scattering cross section (i.e., the product of the width of the intrinsically faulted dislocations with their density) is approximately ten times greater than for extrinsic faulting in these particular samples. An important point is that the relative magnitudes of the energies cannot be inferred from results of this type, unless the intrinsic and extrinsic faults form with equal ease. One must recognize that, although a formation barrier may restrict the amount of extrinsic faulting which occurs, this in no way implies that the extrinsic and intrinsic energies should be different. It is unlikely that a worthwhile estimate of the relative densities of extrinsically and intrinsically faulted dislocations can be made at the high deformations present in X-ray samples. ~oretto,'~ from a statistical argument applied to the nonobservation of extrinsically faulted tetrahedra out of a large sample, concluded that yeXt/yint could not be less than -4.5. However, the present author feels that a high-energy formation barrier as just supposed also explains this finding satisfactorily and that no conclusion can possibly be drawn concerning the actual extrinsic stacking fault energy. The same argument also serves to explain the fact that extrinsic faulting has been relatively little observed in the electron microscope. Extrinsic-intrinsic node pairs and isolated extrinsic nodes were first reported by Loretto~ and subsequently by Ives and Ruff,' Gallaher,' and Gallagher and Wash-burn.' Ives and Ruff' found a wide spread in the ratio of extrinsically to intrinsically faulted area in the node pairs they observed, and drew the very tentative conclusion that yeXt/yint 2 2. They recognized that a straightforward comparison of the size of the faulted areas could provide no more than a qualitative result without a theoretical analysis of the dislocation geometry associated with extrinsic faulting. A theoretical

Jan 1, 1969