Search Documents

By H. Siebel, N. A. D. Parlee

MIZIKAR, Grace, and parlee' studied rates of absorption of oxygen in stagnant liquid silver in a new type of open-ended gas-liquid metal diffusion cell, where the capillary diameters used were 1.5, 2, and 3 mm. They reported that the rates appeared to be controlled by the rate of diffusion of oxygen atoms in liquid silver and they used their data to arrive at the following equation as a reasonably good representation of the diffusivity (D) of oxygen in liquid silver: D = (14.7)10-4 exp (-7100 ± 3200)/RT cm2/sec Since this type of diffusion cell offers a promising method of measuring diffusivities of gas atoms in liquid metals, the senior author of this note and his students are carrying on a critical examination of the method, and are attempting to improve and extend the technique. The research reported briefly here was designed to examine more carefully the earlier conclusion1 that the absorption rate is diffusion-controlled, and to find out whether the diameter of the cell could be greatly increased and thus extend the method to systems where gas solubilities and diffusion rates are much smaller than in the case of oxygen in silver. For the purpose of these experiments, the open-ended capillary cell used by Mizikar, Grace, and Parlee was replaced by a small cylindrical crucible (1 to 1.7 cm in diam) containing pure silver (to a depth of 1.3 to 3 cm) resting in the bottom of a closed-ended vertical quartz tube, with an evacuated quartz filler tube just above the crucible to reduce dead volume. The method of measuring the rate of absorption was otherwise very similar to that of Mizikar, Grace, and Parlee and all the same precautions were taken. A much smaller and shorter tube furnace was used for heating, but simi- lar precautions about temperature gradients were observed. This technique was nothing more than the application of a Sieverts apparatus to the measurement of rates of absorption in small crucibles of stagnant liquid silver. In each run the volume of gas absorbed (V) was plotted against the square root of time (vt) and apparent diffusivities were calculated from the slope of the line, as described by Mizikar, Grace, and parlee.' Care was taken to use only the data obtained during the early part of the total absorption period while the cell functioned as one of infinite depth. The results at 1000°C are summarized in Table I and Fig. 1. The following conclusions may be drawn: 1) Diffusion cells up to 1.7 cm in diam yield, within experimental error, the same values for the diffusivity of oxygen (D) as the capillary cells of 1.5, 2, and 3 mm in diam employed by Mizikar, Grace, and Parlee. Cell diameters as large as 1.7 cm are probably not desirable for the most precise work. Intermediate sizes, perhaps 0.5 cm, will be most practical. 2) All absorptions measured were consistent with a model where the rate is controlled by the diffusion of gas atoms in the metal. The fact that runs at absorption pressures ranging from 0.1 to 1 atm (at any one temperature) give

Jan 1, 1965

By S. C. Libby

Physical degradation of calcined bauxite is related to the presence of goethite in the raw bauxite and to the development of secondary gibbsite. Goethite in the bauxite matrix will shrink and decrepitate during calcining, leaving a friable matrix and allowing disaggregation of the calcined bauxite during transport and handling. A matrix consisting of cryptocrystalline gibbsite alone or mixed with hematite will not shrink during calcination, yielding a calcine with high abrasion resistance. The development of secondary gibbsite between coarse gibbsite crystals also reduces degradation of the calcine by reducing the amount of disruption between grains resulting from differential thermal expansion.

Jan 1, 1981

Reynolds Jamaica Mines, Ltd., has received a $3+ million loan from ECA for the development of what are termed the largest bauxite deposits in the world in Jamaica, B.W.I. This amount is in addition to $11 million already provided. The new agreement calls for delivery of 750,000 tons a year beginning in early 1952. Inco has announced a new alloy containing 35 pet Ni which can be used for many purposes served by the old alloys which ran up to 70 pet Ni. The new alloy "Incoloy" is 35 pet Ni, 20 pet Cr, and the balance iron.

Jan 8, 1951

MEMBERS of the Research Committee lunched to-gether on Monday and discussed the work and plans of the Committee. Some re-assignment of duties was made and a request put in for another member specializing in lead and zinc. By request, Director Flinn of the Engineering Foundation presented the problem of the proposed investigation of iron alloys. It was decided to call together a special committee in May to determine on recommendations. A. C. Fieldner discussed coal research and Chairman Manning was authorized to ascertain by letter ballot the opinions, on certain phases of this, of all members of the Committee.

Jan 3, 1928

One of the first all-hydraulic crawler drills in service at a US open-pit mine has significantly exceeded the penetration rates of comparable pneumatic crawler rigs, according to Atlas Copco Inc. Overall production with the hydraulic unit has been double that of pneumatic crawlers in use. The installation is at the Foote Mineral Co. surface mine at Kings Mountain, N.C., where the company is engaged in mining spodumene, a combination of lithium, aluminum, and silicates. The ore is found in pegmatite dikes, a tough and abrasive host rock with compressive strength of tip to 5800 kPa (40,000 psi).

Jan 9, 1978

By Douglas A. Blankenship, Randall G. Stickney

The corejacking test is a field test designed to measure the response of salt to known boundary conditions. A 1.0-m-diameter salt core is externally pressurized using curved flatjacks placed in the annulus surrounding the core. Time-dependent deformation of the salt is measured by monitoring the diametrical closure of an inner borehole. A finite element elastic analysis of the jack loading system has been performed. The purpose of this analysis was to determine if the original assumption of axisymmetric loading is correct. Six loading cases were investigated, each representing either hypothetical or previously encountered jack configurations.

Jan 1, 1982

By D. A. Singer

A procedure whereby the completeness of search is calculated by using the area of influence of exploratory drill holes or samples is extended to allow for errors of recognition. The size, shape, and orientation of potential targets are mapped in a probabilistic sense on the array of drill holes or samples. The method can be used either to determine how well explored are the subregions within a previously drilled or sampled area, or to test proposed alternative search strategies. Examples of the use of the method demonstrate the complexity of sequential search when the areas of influence of drill holes or samples overlap.

Jan 1, 1976

Engineering Experiment Station, Ohio State University, Columbus, Ohio For publications, send requests and remittances to The University Press, Ohio State University, Columbus, Ohio. A few of the Bulletins of the Engineering Experiment Station will be of direct interest to mining engineers and geologists Bulletin 29, Coal losses in Ohio (1925), 25 cents, 33, A plan of a cooperative sliding scale of wages as applied to bituminous coal mining (1926), 10 cents, 46, The carbonization of Ohio coals (1928), $1; 63, Ohio coal investigation- pt 1, Hocking Valley coal (1931), 50 cents; 67, The Lawrence clay of Lawrence County (1932), 50 cents

Jan 1, 1933

By M. E. Kukura, L. G. Stevens

As described in a previous presentation and in various patents, the Minerals Sciences Div. of UOP, Inc., has developed a modified reduction roast ammonia leach process for nickel laterites. This process gave considerable improvement in extraction over the conventional Caron approach as practiced in Cuba, Australia, and the Philippines. This greatly improved response was obtained with a wide variety of ores. This paper describes the pilot plant flowsheet and reviews the design features unique to the UOP process. Operating results from pilot plant campaigns are compared with bench scale results. Operating problems and their solutions are also discussed.

Jan 1, 1976

Direct Versus Indirect Control of the Economy FACED with placing the nation in a state of partial mobilization, it is expedient that it be done in such a way that the national economy and productive capacity are strengthened. The immediate adoption of direct controls such as Axed prices and wages, rationing, manpower controls, and allocations conceivably could destroy the basis of our free economy. Controls breed more of the same and since the present program is a long term project, it should be undertaken within our present business framework so far as possible or until total war makes it impossible.

Jan 11, 1950

THE National Safety Council will hold the following ses-sions in the Waldorf-Astoria Hotel, New York, N. Y., on Oct. 2, 3 and 4: Oct. 2. 9.30 A. M. 1. Report of past year committees, by Chairman 2. "Safety Pays," by Howard I. Young, Vice-President, American Zinc, Lead and Smelting Co., Mascot, Tenn. (Discussion) 3. Entertainment 4. "Methods and Results of Improved Foremanship Conferences," by H. A. Gilbertson, Director of Per-sonnel, Lehigh Coal and Navigation Co., Lansford, Pa. (Discussion) 5. Appointment of election and resolutions committees Oct. 3, 9.30 A. M.

Jan 9, 1928

The University of Idaho Mining Society held a meeting on Oct. 23, and elected the following officers: President, Sam Bloom; Vice-President, Lloyd McDougall; Secty Treas, Jess W. Wade. Regular meetings are held on the first and third .Tuesdays of each month, for informal lectures and reports on technical subjects. The Mining Club of the University of Wisconsin has held four recent meetings On Oct. 17, sixteen new members were inducted, and a committee was appointed to buy a Liberty Bond. The second meeting, Oct. 31, was devoted to general entertainment, at the home of Professor McCaffery.

Jan 1, 1918

By J. Blodget Britton

To the question, "Do the Pennsylvania anthracites contain phosphorus ?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Iron-masters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows

Jan 1, 1873

By C. E. Shoenfelt

The outstanding development in the Rocky Mountain region for 1937 was the discovery of oil on the Wilson Creek dome in Rio Blanco County, Colorado, in the Morrison formation of Jurassic age. This discovery opens up a vast territory to exploitation and definitely establishes the western slope of Colorado as one of the region's more important oil areas. In former years, a large number of structures on the western slope were tested dry in Upper Cretaceous rocks but are now believed to hold possibilities in older formations, and a number of such structures are in line for drilling in 1938.

Jan 1, 1938

By Stuart A. Bengson

It is extremely difficult to revegetate disturbed sites and mineral wastes in an arid environment because of sporadic and undependable rainfall. Thus, irrigation is often a must for starting seed germination and vegetation. Quite aside from the harsh climate, mining disturbances by themselves cause various adverse conditions for a revegetation program. The problems of revegetating a harsh soil, for instance, are often compounded by the steep slopes of mine wastes. Since these steep slopes intensify the droughty conditions by rapidly draining away soil moisture and accelerating runoff, supplemental irrigation may be the only solution for establishing vegetative cover on the slope.

Jan 8, 1976

By F. A. Kjellin

The problem of smelting steel by electricity attracted years ago the attention of inventors, and as early as 1879 C. W. Siemens constructed his first furnace for the smelting of metals, especially steel. His furnace was of the arc type in which the voltaic arc was formed between a carbon electrode and the metallic content of a crucible, the length of the arc being regulated by an electromagnetic device. This electric furnace, as well as others of similar construction, has the inconvenience that the source of the heat—the voltaic arc—possesses a temperature of 3,700' C., which is much

Jan 1, 1904

By P. L. De Bruyn

The behavior of collectors at the mineral-solution interfaces is usually explained in terms of an ionic adsorption process. Through the distribution of collector ions between the solid surface and the co-existing solution phase the mineral is believed to acquire a water-repellent surface coating. Quantitative adsorption studies have been made on simple flotation systems only within the last few years. Such investigations were made possible by the adoption of the radiotracer method of analysis. As a consequence of these studies a new parameter has been added to aid the understanding of the flotation process.

Jan 3, 1955

By A. A. Collins

When we speak of high copper on a lead blast furnace we think in terms of 4 to 5 pct, or. any lead charge carrying over 1 pct. Any copper on charge will produce its corresponding troubles such as lead well, extra slag losses, drossing problems, and the working up of the dross. This is indeed a very interesting subject and one that used to give the old-time lead metallurgists such as Eiler, Hahn and lles many worries, not so much in the actual operation of the hlast furnace but in the working up of the copper. When the American nletallurgists commenced with the American rectangular-shaped lead blast furnace in the 1870's and got away from the reverberatories such as were in use in Germany and other parts of the world, they went to greater tonnages, as 80 to 100 tons per day in comparison to the 20 to 30 tons per day in the other processes. With the greater tonnages along with insuficient settling capacity, the silver losses in some cases were increased. Hence the lead-fall was low, for there were no leady concentrates in those days to assist the metallurgist to gain lead or an absorber for the precious metals; and in some cases copper sulphides were added intentionally to the charge to produce a copper matte to lessen the silver losses through the dump slag. The operators in those days thought that where some copper was always present in the lead ores the copper should not enter into the reduced lead and alloy with it. This, by the way, is just the reverse of our present-day practice, when we try to put all of the copper into the blast furnace lead and to remove the same through the drossing kettles. Therefore the furnace was operated to produce a certain amount of matte or artificial sulphides, since, due to the great affinity of copper for sulphur, any copper present would enter the matte almost completely. Thus, the lead bullion produced was practically free from copper. The products of the furnace were metallic lead or lead bullion, containing 05 to 95 pct of the lead and about 96 pct of the silver which were in the ore—a lead-copper-iron matte which contained nearly all the copper in the ore and the slag, the waste product. In the United States, up through the year 1092, we find the small furnace 100 X 32 1/2 in. with 12 tuyeres, some 6 on each side, plagued with a small amount of poorly roasted sulphides— either from heap or hand roasters that produced matte. This matte was roasted and if poor in copper was returned for the ore smelting. Otherwise it was smelted either alone or with additions of rich slags or argentiferous copper ores, the products being lead and a highly cupriferous matte, the latter being subsequently worked up for its copper. The lead metallurgists kept trying and improving on furnace and roasting equipment designs until we find blalvin W. Iles constructing at the old Globe Plant at Denver what came to be the modern furnace. That is, in 1900 he built a furnace of 42 in. width by 140 in. at the tuyeres with a 10 in. bosh and a 16-ft ore column. This type has been more or less standard to the present time, though modified in width and length to meet the demand for large tonnages and improvements in structural details. In 1905 at Cananea, Mexico, Dwight and Lloyd developed the present down-draft sinter machine that has meant so much in producing a well-processed material for the lead blast furnace. In 1912 Guy C. Riddell came forth with double roasting at the East Helena Plant of the American Smelting and Refining Co., which removed the "zinc mush plague." Incidentally, with the introduction of double roasting, which most lead plants were forced into after 1924, when lead flotation came into its own, less matte or no matte was produced. When this stage arrived, the copper was forced into the dross and the casting of lead at the blast furnace lead-wells was stopped. In plants with a fair copper carry 1 pct or better on the blast furnace charge, the lead wells became inoperative once the production of matte stopped. The copper drosses clogged the lead wells and even with bombing, either water or dynamite, the operators could not keep them open. Thus, the lead wells were abandoned in some plants, such as at the El Paso and Chihuahua smelters of the American Smelting and Refinillg Co., and all lead taken out through the first settlers. The elimination of sulphur, espccially sulphide sulphur, from the blast furnace charge and the nonproductiori of matte resulted in a great saving of tinie, energy and equipment in the recirculation of the copper, With the copper content in the dross and dross-fall ranging in quantities from a few percent up to 60 pct, such as at El Paso, a drossing problem was created. As the old-time operators hated dross and buried the same in the shipping bullion, the modern metallurgists from 1925 on decided that with increasing dross-falls they would have to adopt the lead refiner's ideas of drossing kettles with subsequent treatment of the lead with a sulphur addition to have the shipping lead of 0.01

Jan 1, 1950

A. Scott Reid, London, Eng. (communication to the Secretary*) :—As a constructor of several glass mine-models, .I have read with much interest the description of the model of the Montana-Toriopah mine-workings by Edmund D. North.

Jan 1, 1910

By John F. Lundeberg

CLAUSS1 observed that if isothermal creep data could be approximated as straight lines on a log stress-log time plot, a relationship existed that could be expressed as log t = m log s + b [ l] where t = time,

Jan 1, 1965