Search Documents

By James E. Lonergan, Young C. Kim

Over the past two and one-half years, various emission control strategies for a coal-fired power plant have been jointly developed by the University of Arizona and the Homer City Owners. The objective of this work was to assist the Homer City management in their efforts to comply with SO2 emission regulations while continuing to use the relatively high sulfur coal from their captive mines as the primary source of plant fuel. One of the operational strategies studied was to have the captive mines minimize the sulfur variability of the run-of-mine coal on a short term basis. A mine production scheduling program called COMPF2 was developed to perform this task. This paper describes the application of this mine planning program at an underground coal mine. A comparison of the planning results with actual production figures showed the ability of this program to schedule production so as to minimize both the sulfur content and the sulfur variability of run-of-mine coal.

Jan 1, 1983

By G. S. Ansell

RCENTLY, in investigating the high-temperature creep properties of an aluminum, SAP-type alloy, MD 2100, fabricated by Professor F. V. Lenel of Rensselaer Polytechnic Institute, Ansell and Weertman1 found unusually low creep rates. These creep rates are 4 or 5 orders of magnitude lower than is predicted by the slowest creep mechanism based upon dispersion-hardened alloy theory. They ascribed these results to a lack of both normal active dislocation sources and a continuous three-dimensional dislocation network. If one couples these results with the following factors of production and microstructure: 1) The compacted and sintered aluminum powder compact is hot-extruded, with an extrusion ratio of 25:1.2 2) The alyminum oxide particles are approximately 140A units thick, and have a spacing varying from 0.05 to 1.5 1. 3 3) The alloy has plate-shaped grains with minor axes of about 5 X 10 -3 mm and major axes several orders of magnitude greater than this.'

Jan 1, 1960

By W. L. Price

Since they were first introduced in the United States in 1964, rail mounted bucket wheel stacker-reclaimers have gained wide acceptance by the coal burning power plant group. Other installations include those in phosphate and steel mill ore storage areas. First Installation in the U.S.A. Three basic types of bucketwheels for handling stored bulk materials are now being used in the U.S. Bucketwheel stacker-reclaimers came into use in the U.S.A. in 1964 at the Chalk Point power station built by the Potomac Electric Power Co. It was decided, after serious study, to install the first slewing-boom, rail mounted bucketwheel stacker-reclaimer at this installation. It was designed with a separately counter- weighted wheel boom because the fixed counterweight of the European designed bucketwheel made it possible for the machine to overturn backwards if the wheel rested on the ground due to a possible failure of the luffing system.

Jan 1, 1970

By C. Y. Chen

Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977 (SMCRA), Section 516 (b), requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence cawing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable we of such surface lands, except in those instances where the mining technology wed requires planned subsidence in a predictable and controlled manner.. . ." Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features. This paper also summarizes some measures used to minimize the possibility of damage to structures as a result of subsidence due to underground coal mining.

Jan 1, 1984

By Hal M. Scrugham

UNITED States Steel Co.'s Tennessee Coal & Iron Div. Wenonah mines present definite materials handling problems arising from the natural features of the operation. Trackless equipment went a long way toward supplying the answers-but at the same time gave birth to several new posers. Machines-trackless or otherwise-require maintenance and Wenonah's experience may do much to add to the body of information already available on this type of equipment. Let's look at the mines themselves. Ore is of sedimentary origin, extending over an area of several square miles. A thickness from 8 to 14 ft is mined. Bed dip varies from the horizontal to 20 pct in local rolls. Practice is to mine across the dip at 14 pct or less. A parting forms a smooth footwall in some of the mines while in others the footwall must be blasted smooth. Ore weighs 215 lb per cu ft in place and is extremely abrasive.

Jan 6, 1953

By William E. Ford, Edward Salisbury Dana

1. Simple Hydrocarbons. Chiefly members of the Paraffin Series C,H2,+2. SCHEERERITE. In whitish monoclinic crystals. Perhaps a polymer of marsh-gas (CHI). Found in brown coal at Uznach, Switzerland. HATCHEITITE. Mountain Tallow. In thin plates, or massive. Like soft wax. Color yellowish. Indices, 1.47-1.50. Ratio of C to H = nearly 1 : 1. From the Coal-measures near Merthyr-Tydvil in Glamorganshire, England; from Galicia. PARAFE-IN. A native crystallized paraffin has been described as occurring in cavities in basaltic lava near Paterno, Sicily. Indices, 1.49-1.52. OZOCERITE. Mineral wax in part. Like wax or spermaceti in appearance and consistency. Colorless to white when pure; often leelr-green, yellowish, brownish yellow, brown. Indices, 1.51-1'54. Essentially a paraffin, and consisting chiefly of one of the higher members of the series. Occurs in beds of coal, or associated bituminous deposits, as at Slanik, Moldavia; Roumania; Boryslaw in the Carpathians. Also occurs in southern Utah on a large scale.

Jan 1, 1922

By W. E. C. A. B. Eustis

(Read at the Philadelphia Meeting, February, 1878.) IN September last I had my attention called by Mr. R. G. Leckie to a deposit of nickel in the township of Orford, province of Quebec. In many ways it has proved to be a subject of great interest. As this ore is, as far as I can learn, entirely new in mineralogy and metallurgy, it has seemed to me that it would be a matter of interest to the Institute to have laid before it, in a short paper, the peculiarities I have met with in studying it. This deposit of nickel was first described by Dr. T. Sterry Hunt, our President, in the Geology of Canada, 1863, p. 738, in the following terms : "The general diffusion of nickel throughout the magnesian rocks of the Quebec group has been already noticed. It has, however, never been met with in any considerable quantities in these rocks, although workable deposits of its ores may reasonably be looked for

Jan 1, 1878

By Telfer Norman

THE use of cadmium as a base for bearing metals is one of the most interesting recent developments in this field. It has caused a strong demand for cadmium and a marked rise in its price. It appeared to the authors, therefore, that the situation might be relieved for users if accept-able substitutes could be developed. A preliminary investigation has revealed that to some extent mercury may be substituted for cadmium. Whether its use is justified cannot be stated at this time. Most of the authors' work has indicated that the addition of mercury to alloys of cadmium and nickel detracts from their desirable physical properties; but this work has not been extended to cover service tests, which might reveal that the addition of low percent-ages of mercury to the cadmium-base alloys would improve their per-formance. The results of tests made by the authors are therefore briefly summarized for this paper. Table 1 gives the proportions of the metals

Jan 1, 1937

By C. T. Sheeran, J. C. Franklin

A commercially available microprocessor-based system capable of monitoring 512 channels has been interfaced with monitors for radon, working level, air velocity, and fan power. The basic system utilizes both 280 and 8080 microprocessors in a desktop central processing unit (CPU). CPU hardware includes keyboard, video display (CRT), and disk drive; a printer is used to keep permanent data records. Signals from all channels are transmitted to the computer in digital form where they are processed for alarm status. Software developed for the system allows for audiovisual alarms in the event of low and high readings, rate change, change of state, or communica- tion failure. Up to six channels can be continuously displayed on the CRT for current readings. Shift reports and trend logs may be generated to help the ventilation engineer determine average working levels and ventilation effectiveness. Additional software permits the operator to program command sequences which may be used to automatically restart fans after a power outage.

Jan 1, 1982

By H. Herbert Hughes

In the years following World War II, L. de Roll S.A., Zurich, Switzerland, perfected its vertical kiln. De Roll first became interested in cement-manufacturing equipment in 1947, not only kilns but also the crushing, grinding, and handling equipment required for a complete cement plant. The parent company, Louis de Roll Iron Works, S.A., Gerlafingen, Switzerland, was founded in 1804. In its six plants, and with its associated companies, de Roll manufactures and installs equipment for a wide variety of industries-chemical and metallurgical operations, fats and oils plants, and municipal refuse incinerators and sewage disposal installations. Vertical shaft kilns, of course, are as old as Portland cement itself. Their fuel economy has long been recognized, particularly in Europe where fuel costs are high. But the disadvantages of old-type shaft kilns have been the lack of consistent quality of the clinker, the small capacity, and the relatively high labor costs.

Dec 1, 1956

The Library Board of the United Engineering Society is desirous of bringing closer to you the facilities and usefulness of your splendid Library. To that end, they have inaugurated a Service Bureau whose duty it shall be to maintain such a staff of expert searchers and translators as to insure prompt and thoroughly efficient service to those of our members whose absence from New York makes it inconvenient for them to pesronally consult the books and periodicals on our shelves. The Service Bureau is also arranging to keep such members as may desire it, posted on the current publications of any engineering subject in which they may be specially interested. The Charter of the United Engineering Society does not permit the Library to carry on any work of a commercial character and, therefore, the prices charged members for this service have to be kept down to a merely self-supporting basis. All the work done by the Library Service Bureau is strictly confidential.

Jan 9, 1915

The mines of the country are called upon to bear a very large part of the enormous taxes to be raised for 1917 and later years. The Internal Revenue Bureau, which is charged with the assessment and collection of these taxes, desires that the taxation laws shall be administered in a fair and business-like way. The application to mines, however, which have wasting assets, involves questions of particular complication and difficulty. To meet this situation, there has been established in. the Income Tax Branch, a Section of Mine Valuation in which these specific problems of the industry will be handled by competent engineers. But it is realized that something more than this is required for the satisfactory application of the tax laws to the mines, namely, as complete understanding as possible between the Government and the taxpayer, a spirit of cooperation as between the two and every possible assistance and advice from mine owners and mining engineers.

Jan 9, 1919

The State School of Mines, University of Utah, is this year giving-a four weeks' course for prospectors-Jan. 8 to Feb. 3, 1917-covering the fundamentals of geology, mineralogy, mining and the metallurgical treatment of ores. There will be 36 lectures of 1 hr. each and about 20 laboratory periods, each 3 hr. in length. It is the purpose of the School of Mines to make the course entirely a practical one, and purely theoretical considerations will be omitted. The laboratory work is designed to supplement the lectures and-to give those taking the course a working knowledge of the principles involved. In order to bring the course within the reach of all, no laboratory fees will be charged, and the only fee will be a nominal one for registration in the University, of $1.00, but it is expected that those who attend will be genuinely interested in the work.

Jan 2, 1917

By Van C. Nyman

A time-sharing computer was tied in to Hecla in August of 1967. This has proven to be helpful in performing metallurgical and engineering calculations that were formerly tedious tasks. Metallurgy programs were written for applying two and three product formulas. Programs were expanded to make the monthly metallurgical balance calculations for each of the Hecla mills. The Hecla engineering department uses the computer for solving hoist duty cycles and for traverse analysis. Both Asarco and Bunker Hill Company in the Coeur d’Alene Mining District are tied to a time-sharing computer. Their uses for the time-sharing computer will be discussed. Asarco had the advantage in learning computer techniques during an extended strike. A comparison of Asarco computer use with that of Hecla's will show the advantage in having a person or persons spend full time on the use of computers. Bunker Hill has the versatility of five teletype units in their mine-smelter complex plus ability to tie in to their own computer.

Jan 1, 1969

JAMES ASHWORTH, Livingstone, Alberta, Can. (written discussion*).-About the year 1878, the writer commenced to experiment on safety lamps, the results of which will be found in the Transactions of the North of England Institute of Mining and Mechanical Engineers 1879-1880, the Transactions of the Manchester Geological and Mining Society, and in the technical press. He has also made a careful investigation of the flame caps produced by chemically prepared methane when mixed with air in accurately measured percentages. Before the conclusion of these experiments he personally fitted the hydrogen gas test to a special pat-tern of the Ashworth-Gray patent safety lamp. Later, as pure hydrogen gas was not always available, the writer constructed a safety lamp that would separately burn oil and alcohol; and still later, a somewhat similar lamp to burn alcohol only for specially testing low percentages of methane. This lamp was known As the Ash-worth alcohol safety lamp.

Jan 12, 1919

By Murray F. Hawkins, W. J. Ainsworth

In all types of subsurface pressure gauges the extension which occurs in the pressure-sensitive element is a function of the difference between the external (well or calibration) pressure and the internal pressure within the gauge, rather than a function of the external pressure only. The internal pressure is near atmospheric and depends upon (a) the quantity of air sealed within the gauge at the time of calibration or measurement, (b) the quantity of moisture (liquid water), if any, sealed within the gauge, and (c) the temperature at which the calibration or well measurement is made. Part of this correction for the change of internal pressure with temperature is taken care of by the customary temperature coefficient of the gauge. However, part of it is not, and while this portion may be only a few psi, it is nevertheless predictable or preventable, and should be considered in precision measurements. ERROR NO. 1 If air is sealed in the gauge at the same temperature and pressure for both the calibration and the well measurements, the usual temperature correction will take care of any difference between calibration and well measurement temperatures. However, if air is sealed within the gauge at temperature T1 and pressure P1 at calibration but at temperature T2 and pressure P2 for a well measurement, because different amounts of air are sealed within the gauge in each case, the internal pressure at. or corrected to, calibration temperature Tr will he different by where all temperatures and pressures are absolute. The calibration temperature is used, and not the well measurement temperature, because the usual temperature correction reduces the well measurements to calibration temperature. The correction term as calculated by the above equation is separate from. and in addition to, the usual temperature correction. Example: T, = 540°R, sealing temperature at calibration P, = 14.7 psia, sealing pressure at calibration T2 = 460°R, sealing temperature at well P2 = 14.7 psia, sealing pressure at well Tr = 660°R, calibration temperature AP = 660 [14.7/460 — 14.7/540] = 3.1 psi While this error is small even under these somewhat maximal conditions, it nevertheless represents a practical situation which did occur, and which as a matter of fact gave rise to this note. Where AP is positive, as above, the correction is added to the measured pressure; where negative, subtracted from the measured pressure. This correction should also be considered in successive calibration runs where the gauge, for example, may be warm from a previous calibration at an elevated temperature. ERROR NO. 2 Where a small quantity of moisture (liquid water) is sealed within the gauge at atmospheric conditions, the increased vapor pressure of the water at higher well or calibration temperatures will cause an increase in internal pressure. This moisture will come presumably from condensation within the gauge following temperature changes, from moisture on the operator's hands, and from atmospheric moisture (rain, mist, fog, etc.). Calculation shows that approximately 0.2 cc of water (three to four drops) is sufficient to saturate the air within an Amerada RPG-3 Gauge at 160°F, at which temperature the vapor pressure of water is about 5 psia. As the vaporization occurs in a sealed volume, the increase in internal pressure will be in excess of this 5 psi. At higher temperatures the pressures will be higher; however more water will be required to saturate the air within the gauge. Some experimental work was carried out with an Amerada RPG-3 Gauge at 200°F fitted with a 1,000 psi element, both with a dry recording chamber and with a small amount of water added. The results directly proved the existence of the error due to the presence of moisture, and, it is felt, indirectly, due to the differences in sealing temperatures and pressures, as both effects may be ascribed simply to an increase in the moles of gas within the recording chamber. SUMMARY In precision measurements the error introduced by sealing the gauge during a well test at a different temperature and pressure from that of calibration may be corrected for by using the equation presented, or it may be prevented by taking care always to seal the gauge at near calibration conditions. The error introduced by sealing moisture in the gauge may be prevented by taking care to keep moisture out of the gauge, or by removing the moisture by either warming or evacuating the gauge. Both of these errors are independent of the range of pressure measurement and the type of gauge, and are in addition to the usual temperature correction. ACKNOWLEDGMENT Appreciation is expressed to W. B. Kendall, Geophysical Research Corp., Tulsa, Okla., who pointed out the error from differences in sealing temperatures during some winter work in Canada. ***

Jan 1, 1956

By R. M. Brown, W. J. Murphy, B. M. Kapadia

An investigatiott was conducted to study the influence of nitrogen, titanium, and zirconium on the boron llardenabilzty effect in a low-carbon constructiona2 alloy steel. The experimental steels investigated exhibited a significant variation in hardenability, the variation being dependent on the interactions of boron, titanium, and zirconium with the nitrogen. Only the boron not combined with nitrogen was effective in increasing hardenability. Titanium, and with lesser effectiveness zirconium, combined with available nitrogen, thereby protecting the boron. The hardenabil-ity effect mas related to an empirical expression for the "effective" boron content, P, deduced from experimental evidence of these interactions. The hardenabzlity effect reached a maximum at about 0.001 wt pct 0, and decreased somewhat as P increased further. The physical understanding of this relationship is discussed. FOR many years boron has been added to steels to obtain high hardenability. Although a great deal of research has been conducted on boron-treated steels, certain aspects of the boron hardenability effect have not been fully understood. For instance, the magnitude of the hardenability effect has been observed to vary markedly, depending on the steelmaking technique, even when the amount of boron in the steel was essentially constant. Furthermore, the optimum amount of this element to be added has not been definitely established. A better understanding of the boron hardenability effect is essential because too small an addition of boron is likely to be ineffective, while an excessive amount can cause brittleness'' and hot shortness. The findings of earlier investigations have shown that the hardenability effect cannot be consistently related to the amount of boron added or retained in the steel. Grossmann observed that in a 0.60 pct C steel the hardenability increased to a maximum with mold additions up to about 0.0025 pct B and then decreased with larger additions. Other investigators5 likewise reported a maximum in the hardenability at about 0.003 pct B. Crafts and Lamont, however, found that in commercial open-hearth heats of medium-carbon steel the hardenability increased linearly with boron up to 0.001 pct and remained essentially unchanged with larger percentages up to 0.006 pct. Other investigators7,' also observed a rather constant hardenability effect in the range about 0.0005 to 0.0035 pct B. These observations and other evidence suggest that the effectiveness of boron in increasing hardenability probably depends, in addition to the amount, on the form of boron retained in the steel, this form being influenced by the presence of other elements. Both oxygen and nitrogen apparently exert the strongest influence on the hardenability behavior, since, at the temperature of liquid steel, boron readily combines with these elements, thereby losing its effectiveness as most experimental evidence seems to indicate. For consistent recovery of the boron effective in increasing hardenability, it is necessary that the oxygen and nitrogen in the steel be either reduced to extremely small amounts by the steelmaking practice or neutralized by combination with other elements before the addition of boron. The importance of achieving adequate deoxidation prior to the addition of boron in order to realize the full hardenability effect of boron has been sufficiently emphasized by earlier investigators. Digges and Reinhart' and others have investigated the role of nitrogen and have shown that nitrogen also interacts with boron and reduces or nullifies altogether its effect on hardenability. Moreover, their work also demonstrated that the addition of strong nitride formers such as titanium and zirconium reduce the deleterious effect of nitrogen on boron hardenability by combining with nitrogen to form stable nitrides. Another element which has a pronounced influence on the boron hardenability effect is carbon. It has been shown7'10 that the hardenability effect of boron diminishes with increasing carbon content, and becomes almost negligible at the eutectoid composition. This observation is useful in comparing the potential increase in hardenability from boron of steels with different carbon contents, but is not relevant to a study of the effects of normal steelmaking variables. The amounts of oxygen and nitrogen in steel vary with the steel composition and steelmaking practice employed. Most commercia1 low-alloy steels are fully deoxidized by the addition of silicon and aluminum, or other strong deoxidizers, which adequately protect the boron from oxidation. In addition, one or more of the elements such as titanium or zirconium are usually added, either separately or in combination with boron, in the form of complex ferroalloys, to protect boron from combination with nitrogen in the steel. However, the actual amount and type of addition employed for a given processing requirement are usually selected by trial and error, and have a rather limited range of applicability. As a result, substantial variations in the hardenability of boron-treated steels are often observed in practice, particularly when the nitrogen content of the steel is a significant processing variable. These variations might therefore be reasonably attributed to the interactions between boron, nitrogen, and titanium or zirconium present in the

Jan 1, 1969

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice Chairman for Production of the Petroleurn Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive, locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert 2; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are deter-minable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations may be involved, our figures should represent as nearly as possible the total quantity of gas removed from the reservoir.

Jan 1, 1936

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron' and molybdenum.' The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,' containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln' wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,' mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953