Search Documents

By E. Buehler, E. Berry

HE magnetic properties of dilute palladium alloys are of fundamental interest.''' Neutron diffraction studies3 have indicated that a better understanding of the behavior of these alloys could be realized with the availability of high-purity single crystals of palladium. Crucible melts of 99.999 pct pure palladium were found inadequate for such research. In a successful effort to fill this need, floating zone refining of palladium was undertaken. In this note the results of the initial experiments are reported. Zoning was accomplished in an argon atmosphere using 450 kc rf generator for an energy source. Samples 5 to 6 mm in diam were suspended in a gastight quartz envelope which could be moved vertically through the rf coil. A nominal upward traverse rate of 1.5 mm per min was maintained during a pass. Close coupling was found to be essential for stable retention of the liquid in the zone. Single crystals averaging 3.5 cm in length were obtained. Laue photography showed them to be continuous single crystals without gross imperfections. Several criteria were used for evaluation of the purity of the zoned material: magnetic behavior, low-temperature specific heat and residual resistivity ratios. Table I shows the residual resistance ratios obtained for two samples, one subjected to a single pass, the other zoned four times. It is appilrent that palladium can be zone refined with the electrically active impurities being transported toward the tail end. A decrease in susceptibility for zone-melted specimens over any previously measured material from 1.5" to 80'~ has been obserted by H. J. Williams and R. C. Sherwood4 substantiating the residual resistance data. The specific heat measurements are currently being made3 and will be published at some later date. Discussions with J. H. Wernick and S. C. Abrahams are acknowledged. We also wish to thank G. F. Brennert for the residual resistance measure ments.

Jan 1, 1962

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By Galen Clevenger

TELLURIUM has had the rare and unpleasant distinction of having fewer uses than any of the other common elements; indeed, it has had no regular or important uses. It is not only a useless and disagreeable element, but to the metallurgist it has been a nightmare. The interference of tellurium with the recovery of gold and silver from certain ores, as well as the difficulties it occasions in the electrolytic refining of copper, lead, and silver, are too well known to require enumeration here. In fact, the potential producers of the element have been quite willing to throw the crude products from which it might be recovered into the sewer. First isolated from a gold ore in 1782, although remaining a practically unknown element to the general public, it has long been a guiding star to the Western prospector in his quest for the "golden fleece." On the burning sands of the desert, in the frigid North, and in the mountain fastnesses of the more temperate regions of this and other continents, he has endured all manner of hardships in his search for tellurides; for where he found indications of tellurium, there he expected also to find rich deposits of gold and silver. This peculiar superstition, that tellurium, associates itself in nature with the precious metals, is not with-out reason, for witness the fabulously rich gold tellu-ride deposits of Cripple Creek and Western Australia. Selenium, the sister element of tellurium, which it resembles in many of its properties, was first isolated in 1817. It is found in small amounts in certain native sulfur deposits, and in many copper and silver ores from all parts of the world. Until a few years ago, selenium, like tellurium, was practically useless. The, unusual property of having its electrical conductivity influenced by light has long been known. Selenium cells, which for many years have been a scientific curios-ity, in the future may come to be of more commercial importance, but this use could scarcely absorb any large amount of the element.

Jan 1, 1923

By Cyril S. Taylor, Junius D. Edwards

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Kenneth Cottingham

The area described herein is situated on what is known as the Arches Fork anticline in Roane and Calhoun Counties, W. Va. When the area was first mapped, it was felt that well records would give a more intimate idea of conditions, both structural and lithologic, than could be expected from surface horizons. The surface formations are chiefly members of the Monongahela series, though northward the hilltop outcrops are those of the Dunkard. Neither series offen a key horizon sufficiently definite to be satisfactory, although the structure as determined from well records was later checked against two of the more persistent surface sandstones. In mapping the subsurface structure, the top of the Big Lime (Green-brier) was employed as the key horizon. The average depth to the top of the Big Lime varies from 1600 to 2000 ft. (487 to 609 m.), while the average thickness as indicated by well records is 113 ft. (34 m.). The oil-producing formation is the Big Injun, lying just below the Big Lime. In two instances, well records show the Lime and Injun separated by a few feet of "break." The Big Injun is recorded as having a variable thickness. Seven logs report it as missing and one gives it the maximum thickness of 105 ft. (32 m.), while the entire average for thickness is 19 ft. (6 m.). Relation of Structure to Thickness of Big Injun The seven wells reporting the Big Injun as absent were located near the anticlinal axis. Moreover, the general tendency is a thickening of the Injun on the flanks of the anticline, increasing with distance from the axis. Manifestly, this apparent anomaly has no stratigraphic basis, as the actual thickness of the Big Injun and the overlying Big Lime was determined by original deposition which no amount of subsequent folding could appreciably alter. Fig. 1 is a skeleton map of structure based on the top of the Big Lime; Fig. 2 is a cross-section showing the thickness of the Big Injun.

Jan 1, 1923

By Walter S. Weeks, Vitaly S. Grishkevich

Considerable difference of opinion seems to exist as to whether the rate of air flow when a fan is placed on a given duct should be determined by the use of static pressure or total pressure characteristics. A little study will show that both methods are correct. Assume that a fan is connected to a duct by an expansion piece as shown in Fig. 1, and that steady flow is established. Considering the atmospheric pressure as zero pressure, let the static head at the outlet of the fan be h and the velocity at this point be vl. The total head at the outlet is then h + „"• The total head at this point must be equal to the total head at the end of the duct plus the losses that have occurred between the two points. Left be the friction loss in the straight duct, s the shock loss in the dif- fuser, and v2 the velocity at the end of the duct. Then ig. 1.—Fan on duct. A curve showing the value of the left-hand side of the equation for different rates of flow is the total pressure characteristic of the fan, while a curve showing the value of the right-hand side is the total pressure characteristic of the duct. If these two curves are plotted on the same chart, the intersection indicates the rate of flow when steady flow is established. We may look at this problem in another way. The static pressure at the outlet of the fan is the static pressure of the fan and it is also the static resistance of the duct from that point to the end. The friction in the straight duct is f. If the duct were the same area as the fan outlet, would be the static resistance of the whole duct system. In the present case, however, this resistance is decreased by the change of velocity head into static head in the expansion piece. If conversion were perfect, the static pressure recovered would be

Jan 1, 1931

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Kenneth Cottingham

The area described herein is situated on what is known as the Arches Fork anticline in Roane and Calhoun Counties, W. Va. When the area was first mapped, it was felt that well records would give a more intimate idea of conditions, both structural and lithologic, than could be expected from surface horizons. The surface formations are chiefly members of the Monongahela series, though northward the hilltop outcrops are those of the Dunkard. Neither series offen a key horizon sufficiently definite to be satisfactory, although the structure as determined from well records was later checked against two of the more persistent surface sandstones. In mapping the subsurface structure, the top of the Big Lime (Green-brier) was employed as the key horizon. The average depth to the top of the Big Lime varies from 1600 to 2000 ft. (487 to 609 m.), while the average thickness as indicated by well records is 113 ft. (34 m.). The oil-producing formation is the Big Injun, lying just below the Big Lime. In two instances, well records show the Lime and Injun separated by a few feet of "break." The Big Injun is recorded as having a variable thickness. Seven logs report it as missing and one gives it the maximum thickness of 105 ft. (32 m.), while the entire average for thickness is 19 ft. (6 m.). Relation of Structure to Thickness of Big Injun The seven wells reporting the Big Injun as absent were located near the anticlinal axis. Moreover, the general tendency is a thickening of the Injun on the flanks of the anticline, increasing with distance from the axis. Manifestly, this apparent anomaly has no stratigraphic basis, as the actual thickness of the Big Injun and the overlying Big Lime was determined by original deposition which no amount of subsequent folding could appreciably alter. Fig. 1 is a skeleton map of structure based on the top of the Big Lime; Fig. 2 is a cross-section showing the thickness of the Big Injun.

Jan 1, 1923

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

Have your name and address on the first page of your manuscript. Typewritten manuscript is preferred, but is not essential. If you have the manuscript typewritten, have it double spaced and written on one side of the page only; send two copies to us if convenient; only one copy of the illustrations is desired. In typewritten manuscript, formulas are better inserted by hand. Keep a copy of your manuscript in case of loss in the mail. ILLUSTRATIONS.-Photographs reproduce best when printed on glossy paper. Solio is one of the best varieties. A good print is preferable to a negative. Blueprints, drawings, or pen or pencil sketches can be used for line engravings, but care should be exercised to make them legible and clear, especially in the case of blueprints. Tracings or photographs of drawings are preferable to blueprints. Rough sketches can be used, if necessary. Photographs should be sent flat, not rolled. Do not put reference letters or other marks on photographs; if such letters or marks are necessary, fasten a piece of tracing paper to the top edge, trace a rough outline of the picture upon it and then place all letters, etc. on the tracing paper lithe exact position you wish them to appear. Restrict the number of micrographs as much as possible on account of the considerable expense involved. Standard magnifications for non-ferrous metals and alloys are recommended as follows: 10, 25, 50, 75, 100, 150, 250, 500, 750, 1000, 1500. Micrographs should be trimmed to 2 1/4 X 2 1/4 in. (six micrographs to a plate), or, if larger, up to 3 1/2 X 4 in. (two to a plate). The smaller size should be adopted if consistent with adequate representation of the subject. With each micrograph should be attached an explanatory title, together with the actual magnification, etching medium, treatment, etc., indicating what the author intends to show.

Jan 1, 1919

Discussion of the paper of Godfrey T. Vivian, presented at the Cleveland meeting, October, 1912, and published in Bulletin No. 76, October, 1912, pp. 1103 to 1109. COURTENAY DEKALB, Tucson, Ariz. (communication to the Secretary*) :--Mr. Vivian's paper is interesting as an evidence of renewed attempts to solve the problem of adapting the centrifugal machine to the uses of the metallurgist. It would not seem that the Gee machine has solved the problem, because it is manifestly of use only with quite high-grade material, since low-grade pulp could not stand the cost of treatment by a discontinuous process. The mechanism, however, would seen to accomplish grading more perfectly than the ordinary centrifugal basket. This is an entirely different thing from concentration, which is intended to yield a finished marketable product. The real problem is to design a successful continuous centrifugal machine. Ten years or snore ago a machine, which might be described as having an inverted step-basket, offered much promise, and was constructed and tested at considerable cost, but it presented insuperable difficulties. The construction of a successful continuous centrifugal would be welcomed by the whole industrial world, since its uses would be most extensive. Mr. Vivian suggests the utilization of the centrifugal machine as a substitute for slime filters in the cyanide process, but he, has apparently not tried the experiment. I tested the efficiency of centrifugal machines for this purpose in 1897-8, having to extract the cyanide solution from a highly argillaceous slime of the sticky kind which the Mexican call ?lama." Our filter-presses yielded cakes containing usually :30 per cent. of moisture, and so dense as to preclude washing. The centrifugal machine readily Brought the moisture content down to 9 per cent. and permitted fairly successful washing. Despite these advantages, the cost of power, labor, and repairs, and the loss of time in discharging the cake, exceeded the costs and

Jan 5, 1913

By B. L. Sackett

IN a general way, the situation in copper smelting is quite similar to that of lead smelting. In other words, the introduction and successful flotation of copper ores has tended to decrease greatly the tonnage to be handled by the smelter and therefore has resulted in curtailed smelter operation. However, copper production has increased rather than decreased. The general effect of flotation has been to decrease the number of furnaces operating, but it has also increased to a considerable extent the difficulties in handling the material, just as was outlined in the case of lead smelting. In copper smelting, the flotation concentrates must be roasted and prepared for the reverberatory furnace. HANDLING FLOTATION CONCENTRATES The handling of copper flotation concentrate, which is more or less wet and mucky, is more difficult than was the handling of the old gravity concentrate. Also, the roasting of the concentrate and the handling of the calcine produced is more difficult. That is mainly because the material is extremely fine and the tendency to higher dust losses is greatly increased. The draft in the roasting furnaces must be kept as low as, possible, and the feeding of the calcine into the reverberatory furnace must be done carefully, so that dust losses may be kept at a minimum. TRANSITION STAGES OF CONCENTRATION AND SMELTING The general process through which the copper smelter has gone as a result of flotation has been somewhat as follows: In the relatively old days, when copper ores of low grade were first treated, a large number of furnaces were required, and naturally comparatively poor recoveries were made. Also, the profits on low-grade ores were small and the handling of those ores was possible only because of the large tonnages. Then came gravity concentration, which was a great improvement but which only incompletely removed the gangue material, the insoluble and the iron, from the copper ore, and made comparatively poor copper recoveries. This still left a considerable amount of insoluble and iron, as well as the copper itself, to be treated at the smelter.

Jan 1, 1928

By H. De Cizancourt

Peche1bronn.—So far Pechelbronn is the only producing district. Figures are given in Table 2 covering the main features of the field, but these figures call for the following remarks: First, Pechelbronn should not' be considered as a single unit, it appears, but as a succession of small oil fields, each of which is affected by very variable conditions. Consequently, certain figures concerning production per acre, production per acre-foot, pressure conditions and thicknesses of oil sands would be so misleading that they have been omitted here. Second, as regards production methods, attention is drawn especially to the fact that 42 per cent of the oil is extracted by the use of shafts and galleries and the remainder by pumping wells. Exploitation, formerly confined to Oligocene sands, has been extended recently to Jurassic and Triassic oil-bearing formations. Gabian.—This small oil field, discovered in 1924, is almost exhausted. Exploitation to date is restricted to three wells. There were no drilling activities in 1933. Exploration.—During 1933, two exploration holes have been started in France. The first, in the vicinity of Lavelanet (Ariége) on the Dreuille anticline, has reached the depth of 2400 ft,.; the second, in the Autun Permian Basin, is drilling at 1300 feet. Northern Africa Morocco.—Drilling operations have been on a large scale in Morocco. In the Gharb district (Souk el Arba area), the deepest well was abandoned in 1933 at 7014 ft. Small irregular productive horizons were encountered in the Miocene at shallow depth, oil and gas showing in the Eocene, but no commercial oil field has been discovered. In the Djebel Tselfat, near Petitjean, a small production of oil was obtained from a Jurassic horizon. In the meantime deeper formations are being explored and a new structure in the vicinity is being tested. In Eastern Morocco, a well is drilling near Taza. Production in Morocco, about 2400 bbl., has not been listed on Table 2, owing to its origin—exploration wells.

Jan 1, 1934

By D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, Ill. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation was removed. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow readings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through wet washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main was fabricated from riveted sheets led us to discard the idea of using Pitot tubes for this service. The Venturi tube was then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made.

Jan 2, 1921

By F. C. Holman

It is desired in these notes to record a vein-phenomenon certainly unique in the writer's limited experience, and, as it seems to him, sufficiently rare to be worthy of mention. In the little mining camp of Forbestown, situated in the Sierra Nevada of California, it was announced one day, when the miners of the Cold Banks mine came off shift, that "washed gravel" had been struck on the 265-foot level. To those acquainted with that section and the character of the mine (a gold-bearing quartz-vein) this was a somewhat startling announcement; for, prolific as the State is, we are not in the habit of mixing up promiscuously our vein- and placer-deposits. However, the statement proved to have some foundation. The mine is located at an altitude of about 2700 feet, on the brink of one of the great canyons of erosion characteristic of the drainage of this range. A lateral ravine cuts the vein at right angles, thus making its general strike approximately parallel to the canyon at this point, and with a variable dip of from 20 to 40 degrees towards the canyon. The strong, well-defined vein, often 20 feet wide and more, presents nothing to distinguish it particularly from scores of others in the State, unless if be considered peculiar in the highly crystalline character of its quartz and the nature of the enclosing country-rock, which is metamorphic in the extreme, very hard, devoid of lamination, and in bedding so obscure that it might easily pass—at least on superficial examination—for one of the basic eruptives. Near by in the district can be found a series of slates common to the gold-belt of this range, and within the limit of the company's property is an intrusion of an acid eruptive. On an adjoining claim a granite shows itself. The mine is opened through an inclined shaft sunk on the vein. The ore carries both free gold and sulphurets, the greater part of its value

Jan 1, 1896

By Alfred H. Brooks

PetRoleUm seepages are known in Alaska at four localities, all on Pacific seaboard. These, named from east to west, are Yakataga, Katalla on Controller Bay, Iniskin Bay on Cook Inlet, and Cold Bay on the Alaska Peninsula. Besides these, a petroleum residue has been found near Smith Bay on the north Arctic coast of the Territory. At Katalla, Cold Bay, and Iniskin Bay there has been some drilling for oil, and in the first field several productive wells have been opened up. Alaskan petroleum, so far as its composition is known, is a refining oil, with paraffin base and low sulphur content. Most of what is known of the geology of Alaska oil fields is based on the investigations of Dr. George C. Martin, of the United States Geological Survey. A, G. Maddren, of the same service, has recently made a reconnaissance of the Yakataga oil field. The data to be here presented are chiefly taken from the following publications: G. C. Martin: The Petroleum Fields of the Pacific Coast of Alaska, with an account of the Bering River coal deposits, Bulletin No. 250, U. S. Geological Survey, pp. 9 to 27 (1905). G. C. Martin: Geology and Mineral Resources of the Controller Bay Region, Alaska, Bulletin No. 335, U. S. Geological Survey, pp. 112 to 130 (1908). G. C. Martin and F. J. Katz: A Geologic Reconnaissance of the Iliamna Region, Alaska, Bulletin No. 485, U. S. Geological Survey, pp. 126 to 130 (1912). A. G. Maddren: Mineral Deposits of the Yakataga District, Bulletin No. 592, U. S. Geological Survey, pp. 143 to 147 (1914). Katalla Field The Katalla field is marked by a series of seepages and gas springs occupying an east and west belt, about 25 miles in length and from 4 to 8 miles wide. (See Fig. 1.) This zone skirts the north shore of Con-

Jan 1, 1915

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By C. A. Hartinagel

During 1941, the total production of crude oil in New York state was 5,185,000 bbl. This represents a small increase over the average for the past five years. From 1921, when the annual production of the state amounted to only 988,000 bbl., there was a regular annual increase in production (excepting one or two years) until the 5,000,000-bbl. mark was reached in 1937, After more than 20 years of oil recovery by flooding methods, it was generally believed, until a few months ago, that the rate of production was nearly at its peak and within a few years the fields would experience a gradual decline as the thicker sands became exhausted and the thinner ones could be worked only at increasing costs. As a result of the present emergency, however, unusual efforts are being made, in spite of higher costs of operation, to increase the output of Pennsylvania grade oil, to which the New York product belongs. Since most of any increased production would be obtained by flooding, and since floods travel slowly, no large increase in production can be expected for some months to come. During the first year, 10 or 15 per cent increase could be obtained, but maximum production, an increase of perhaps 40 per cent, could not be expected until some time during the second or third year. In the Allegany fields, which account for two thirds of the state's oil production, 1246 wells, including water-intake wells, were drilled during the year; 390 more than in the preceding year and 590 more than in 1939. It is evident that much of the best oil territory has already been developed. As producers move toward edge properties and thinner sands, returns will be smaller, whereas costs remain the same or, under war conditions, become higher. It is estimated that at least 60 million barrels of oil is in sight and will be produced from the thicker sands by present recovery methods. In the thinner sands and edge properties, some 35 million additional barrels can be produced at a profit only if prices become higher. In view of the fact that there is little hope of finding new oil pools in New York, one of the future problems of the oil producer will be to obtain adequate returns for increased production costs. The year started with a posted price of $2.15 per barrel of crude. There were five successive price increases until the high of the year was reached at $2.98 on Aug. 14. Eight days later the Office of Price Administration directed that the price be reduced to the June level of $2.75 a barrel, which remained in effect to the end of the year. With rising costs of operation, it is feared that many of the smaller properties cannot continue production unless the Federal price cut is revoked. During the year, Allegany Refiners Inc., a local enterprise founded in 1933, with plant at Bolivar, western Allegany County, increased its refining capacity from 1000 to 1500 bbl. daily. At the same time equipment was added to make the plant a complete lubricating-oil refinery, including facilities for the refining of wax into the finished product. Previous to the enlargement, it was necessary to sell the wax

Jan 1, 1942

By P. Ramachandraraa, T. R. Anantharaman

THE technique developed by Duwez, Willens and Kle-ment' for rapid solidification of molten alloys in small quantities by ejecting them on to a highly conducting substrate with the aid of a shock wave has come to be known as "liquid quenching" or "splat cooling" in literature and has already been applied to alloys of many binary systems.' The very high cooling rates of the order of l060 to 1080 per sec obtained in this technique and the consequent drastic undercooling of the melt have led to such striking results as formation of new amorphous and crystalline metastable phases and extension of solid-solubility limits in many alloy systems. The cooling rates in these experiments can, however, be neither accurately measured nor effectively controlled and hence the occurrence of either more than one metastable phase or appreciable differences in constitution in splat-cooled alloys of the same composition cannot be ruled out.3 In fact, workers in two laboratories have reported formation of two different cubic metastable phases in liquid-quenched Au-Si alloys containing 17 to 20 at. pct si.4,5 The present note deals with some new and interesting results obtained in a Ag-21 at. pct Ge alloy and a Au-27 at. pct Ge alloy subjected to the liquid-quenching treatment at different cooling rates. Two alloys of nearly the same composition had earlier been rapidly solidified by the standard "gun technique" in the same laboratory and shown to solidify in nonequilibrium structures, viz., an hcp phase (a = 2.987Å;c =4.718Å) in the Ag-Ge system6,7 and both hcp (a = 2.885Å; c = 4.754Å) and tetragonal (a = 11.627A; c = 22.491Å) phases in the Au-Ge system.3 Apart from different substrates (copper and stainless steel), different melt temperatures (50º to 500°C above the liquidus), and different capillary sizes (0.4 to 1.5 mm diam) in the "gun technique", slower cooling rates of the order of l050C per sec were also obtained in the present work by replacing the substrate by water at room temperature in a modification of the technique due to Olsen and Hultgren.8 No attempt was made to measure the cooling rate in any experiment. The products varied from fine powder (>40 pct by wt—200 mesh) obtained by quenching in water to thin flakes and foils (11.0 sq mm to 4.0 sq cm) produced by splat cooling. They were subjected to the Debye-Scherrer method of X-ray examination in each case. In case of the Ag-Ge alloy, in addition to the expected metastable hcp phase,6 a coexistent tetragonal phase (a = 5.093,Å; c = 7.009Å) was detected in some experiments. Eight weak X-ray reflections from this phase could be identified, two of them being the same as reported earlier.7 With increase in the cooling rate, the dominant hcp phase seems to be first accompanied by traces of silver or germanium and then either homogeneous or mixed with traces of this new tetragonal phase. The splat-cooled Au-Ge alloy showed generally the expected hcp and tetragonal phases,3 but sometimes traces of germanium were also present. Further, two new tetragonal phases with the following lattice param ters could be clearly identified in samples quenched

Jan 1, 1970

The sudden and untimely death of Dr. Charles R. Van Hise, late' president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people's university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise's contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise's death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920