Search Documents

By H. J. C. MAC DONALD

THE mining engineer must have a chest of books snug enough for a camelback or to be stowed away in a canoe; at the lowest possible cost, as he needs it the most in those early years when he earns the least; but at the same time one having an unusually wide range, for he may have to cut down a forest, put up a sawmill, build mine towns, construct dams, power houses, power lines, and railroads. In fact he may be called upon for many unexpected accomplishments and all in extension of the characteristically broad demands of his profession. Suppose that an average mining engineer with a thorough theoretical training and a specialized mining education has accumulated, during a cosmopolitan experience, a complete and up-to-date library, but, unfortunately, in accepting a long term assignment to a far country he is forced to discard the greater part of

Jan 1, 1925

By AIME AIME

AT the meeting of the Iron and Steel Division at Cleveland, Sept. 10-12, the morning of Thursday, Sept. 12, has been set aside for an excursion to visit the ore docks, blast furnaces, and steel plants. A special train, made available through the courtesy of Appleton Cleveland, general superintendent of the Pennsylvania Railroad, will leave the siding near the Auditorium at 8.35 a. m. The trip will be free, but tickets must be' obtained in advance at the booths for registration for excursions at the Auditorium. An hour will be spent at the docks, an hour at the Central blast furnaces, and two hours at the Cuyahoga works of the American Steel and Wire Co. A buffet luncheon will be served, with the compliments of the Pennsylvania Railroad Co., on board the train en route. At the Tuesday morning session, Sept. 10, a motion picture showing the operations in making wrought iron by the Aston process will be shown for the first time.

Jan 1, 1929

Map

Jan 1, 1939

By R. Kossowsky

Structural changes in Be-Cu, Be-Ni. Be - Ag, and Be-Fc alloys pressurized in a solid medium were invesligated by resistivity measurements , X-ray diffrac lion in situ and metallogvaphic examination. Some limited tests in liquid medium were also conducted. Good correlation was oblained between diauges of slope of relative resistance us pressure and changes in diffraction pattern. Metallographic examination rez:ealed that the copper, silver, and nickel alloys lwiu heauily due to the applicalion of pressure at room temperature. Using polarized light technique {1012}, {1011}, and possible {1010} twinning planes were identified. At eleuated temperature twinning was moslly confined to the {1012} planes. Although twin-ning could be promoted by application of hydroslutic pvessure (liquid medium), it was strongly enhanced by the pvesence of a nonhydvostatic shear component due to pressurizalion in a solid medium. It was further obserced that a decrease in grain size inlnibiled twinnitzg activily. A great deal of effort has been expended in recent years to render beryllium useful for structural applications. Efforts were concentrated towards a possible phase change and to promoting other than basal deformation modes. Quenching experiments to obtain the high-temperature bcc phase have failed,' nor were alloying additions successful in improving ductility of the brittle hcp phase.2 Herman et a1.3 have reported a new {1011} twinning mode in a Be-4.4 wt pct Cu alloy oriented for a C axis compression sustaining loads to 440,000 psi. A new approach using high-pressure techniques was undertaken at Curtiss-Wright, Wright Aeronautical Division Laboratories. Marder4 reported a 25 pct decrease in relative resistance of commercially pure beryllium at 92 kbar. He proposed that this discontinuity corresponded to the bcc phase found at high temperature; however, X-ray diffraction in silu did not confirm a phase transition.5 contre6 has recently shown that the bcc transition in pure beryllium is lowered to 800°C at 80 kbar accompanied by a 50 pct increase in relative resistance. The purpose of this paper is to report on one phase of an investigation of the effects of high pressures and temperatures in beryllium alloys, namely, twinning behavior in Be-Ni, Be-Cu, Be-Fe, and Be-Ag alloys pressurized to nearly 100 kbar and temperatures up to 200°C. EXPERIMENTAL METHODS Material was obtained from Nuclear Metals, Inc., in the form of a 1.5-mm-diam wire extruded in stainless-steel cladding at 1600° F. Nominal composition of the alloys is listed in Table I, and the major impurities are are given in Table 11. Pressures to 100 kbar* were ob- tained using a National Bureau of Standards type 100/400 ton tetrahedral unit supplied by Barogenics, Inc. This type of apparatus contains a retaining sleeve with a conically tapered internal surface and four pressure-intensifying anvil assemblies with tungsten carbide tips. The 10-mm-long specimen fits into a pyro-

Jan 1, 1968

By D. N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in western Pennsylvania. The coal bed mined is in the Lower Freeport seam, which averaged 1.07 m (42 in.) in height locally. Drainage from the mine is about 13.25 ML/day (3.5 million gal per day) of water. This water deteriorates the mine's predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplilshed by pulling the 5.44 t (6 st) shields out under their own hydraulic power and transporting them by track 8.05 km (5 miles) to the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1985

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925

By G. D. Marshall, D. K. Sarin, V. E. Hampton

Ground support at the Thompson Mine emphasizes scaling, rock bolting and wire mesh screening on the backs and walls of all underground stoping and development areas and also full column grouted cable bolting in the bulk mining areas. This paper describes the equipment for the point anchored rock bolts as well as the full column cable bolts. Modifications in design and testing of all components and procedures has ensured a safe and efficient method of ground support for the mining conditions existing at the Thompson Mine.

Jan 1, 1983

By Clemens Jones

An interesting paper by J. E. Merion and Edward Hart, in Volume I., No. 2, of the Journal of Analytical Chemistry, on the Decomposition of Blast-Furnace Cinder by Acid, describes a plan of sampling the cinder by means of a previously-heated iron bar thrust into the cinder car or into the cinder at the notch, and then allowed to cool, thus chilling the cinder which adheres to the bar, and rendering it decomposable by hydrochloric acid, of 1.12 sp. gr. A short series of results is given, from which the deduction follows that blast-furnace cinder " is decomposed perfectly when chilled." Where many silica determinations are to be made, this method, if reliable, would effect notable economy of time and reagents. The conversion of insoluble silicates by fusion with an alkaline carbonate, together with the subsequent solution, evaporation, drying, etc., is destined to remain the standard method. But all fusionmethods are time-consuming and expensive. Chilling appears to render the supplementary method available for all practical purposes, in the determination of silica in cinder. But, with a view of securing more evidence on the subject, and in view of the fact that uniform results were not obtained by employing this method, it was decided to test the method in the laboratory of the Thomas Iron Company where a large number of silica determinations are made. The experience met with may not be devoid of value, both theoretical and practical. Mr. Iles's paper, in the Chemical News, Volume L., 1881, doubtless suggested to several chemists, connected with iron metallurgical

Jan 1, 1888

Safety and health are no longer secondary responsibilities but must be of paramount concern to every mining operation, according to Anthony J. Thompson, an attorney with Hamel, Park, McCabe & Saunders of Washington D.C. The Mine Safety and Health Administration (MSHA) forecasts an estimated 19,000 inspections during 1979, and the economic and psychological impact of these inspections may he significant. To illustrate his point Thompson reviewed the experiences of a relatively large operation during a recent MSHA visit. The inspector was on the premises for two months, issuing between 250 to 300 "significant and substantial" (s&s) citations. During the most intensive period, about one month in duration, the operation experienced a production loss estimated between 2500 to 3000 tons; an accident rate up 30% over the previous month and 20% over the same month in the preceding year; 100% of the safety director's and safety engi¬neer's time was devoted to the inspection; 50% of top level management's time; and 90% of the mid-level or front line supervisory's time.

Jan 11, 1979

INDEX TO TRANSACTIONS After a delay of many months, which is very much regretted, but which, it is hoped, will be one means of insuring a volume of accuracy where accuracy is very important, the Institute now has for distribution copies of the index of Volumes XXXVI to LV, inclusive. This is more than a mere index off names of authors and titles of papers. Every important topic under consideration by author or discusser is introduced under such key-word as will enable an engineer to locate the desired information with the minimum expenditure of time. This index sells for $5* in half morocco binding and $4*. in paper covers. With the index of Volumes II to XXXV (which sells for $5 in half morocco and $4 in paper covers), it forms a complete index of the first fifty-five volumes of the Institute's Transactions. These collective indexes are very valuable to members of the Institute, enabling them to look up matters in their own library; if they have the volumes to which the indexes refer, they can get the information at once, and, if not, they can readily determine whether or not a visit to a nearby public library is desirable.

Jan 7, 1918

By P. K. Lucke

ONE of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebOdies occurred. This table land lies at altitudes ranging from 4000 to. 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. FIG. 1. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulphides above, and I will endeavor to explain the causes of the phenomena in certain specific instances.

Jan 6, 1918

By T. Kunitake, H. W. Paxton

The self-diffusion coefficient of chromium in various alloys in the iron-chromium system has been measured. A variation in Dofrom 10-4 for pure chromium to a maximum of 102 near 60 pct Cr appears with a range of activation energy from about 50 to 80 kcal per mol. The general pattern of behavior observed is not consistent with present theories of diffusion by a vacancy mechanism. Suggestions are made for further clarifying experiments. RECENT work on the self-diffusion of chromium,' ?-uranium2-4 and ß-zirconium,23, 26 has indicated that these elements have very low Do (10-3 to 10-4) compared to that conventionally expected for vacancy diffusion. Pound et al.5 have suggested that this may be due to ring diffusion being operative, and have proposed a model which gives Do of the correct order of magnitude. The essential difference between this model and Zener's earlier model6 is that whereas Zener assumes tight coupling between atoms in a ring to establish a vibrational frequency, Pound's model allows the atoms to vibrate essen- tially each in their own normal modes. The probability of each atom moving in the correct direction to cause a ring of n atoms to rotate by 2p/n must then be calculated as a "synchronal entropy" which may be -20 e.u. for a 4 atom ring. In iron, the latest determinations of self-diffusion yield Do in the range 18 to 522.7-9 The most accurate is probably that of Borg and Birchenall8 which is 118 ± 3. This value is not inconsistent with that expected for a vacancy mechanism. Since iron and chromium are very closely similar in size, are both transition metals, and their solution is thermodynamically ideal at temperatures of interest in diffusion, it appeared that a determination of self-diffusion coefficients, Do and Q as a function of composition would be of substantial interest to diffusion theory. The following measurements were made with this purpose in mind.

Jan 1, 1961

By Sir Albert E. Kitson

The manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In certain respects they have a strong resemblance to those of India and Brazil, as contrasted with those of Tertiary age in Georgia, but in this paper no careful comparison with them can be made. Viewed from the present condition of the manganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments. Youngest are the products of decay and degradation with the concentration of manganese oxide in the rocks of both groups. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate degree of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flows, largely of basic types. This has been named the Birrim System. Its age is unknown, for no definite fossils have been discovered in it. Since these non-fossiliferous strata at many plaees are of a character which in many parts of the world are suitable for the preservation of fossils, and which contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim System have normally a northeast-southwest strike, and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed diagonally across their strike for upwards of 600 miles, to the extreme northwestern corner of the Northern Territories. Thence they probably extend much farther into French territory.

Jan 1, 1927

At the meeting of the Board of Directors held on October 25, the reports of the Treasurer and the Nominating and Finance Committees were received. Thirty-five members, seven associates, and six junior associates were elected; one change of status front junior associate to member was granted; six members were reinstated; and one resignation was accepted. An extension of' time was granted to fourteen members. The dues of forty-seven members were suspended on account of their being in active service. The application for formation of a Houghton Section was granted and the president was authorized to appoint a committee on organization. The courtesies of the Institute were extended to visiting engineers of France, Great Britain and Italy who are at present in the country on war missions. Votes of thanks were extended to the Committees of the .Milwaukee meeting. The proposed Survey of Engineering Organizations by Engineering. Foundation was approved. The Secretary was authorized to publish in the Bulletin an appeal from the American Ouvroir Funds. A petition signed by 110 members of the-Institute to change the name of the Institute was presented. Treasurer George C. Stone resigned on account of contemplated absence from the city, and George D. Barron was elected Treasurer in his place. Mr. Alexandre Gouvy, a distinguished French engineer, then addressed the Board.

Jan 12, 1918

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956

The American Society of Mechanical Engineers extends an invitation to members of the Institute to participate in an exceedingly interesting excursion on Saturday, November 11. Permission has been secured for a visit to the plant of the Electric Boat Co. at New London, Conn. There will be run a special-test on a high-power 8-cylinder, 4-cycle Diesel engine. A large number of submarine and other engines in various stages of construction will be seen, also the boring of torpedo tubes, cylinders and other equipment for submarines. The drafting rooms and foundry mill also be open for inspection. The party will have an opportunity to see at close range the submerging of several submarines, and an attack on a vessel on the surface, an exhibit which is being arranged by courtesy of Rear Admiral A. W. Grant, who is in command of the submarine forces of the United States. The Boston members will leave South Station on train No. 7 at 8.30 A. M. Those from Providence will board this train at 9.36 A. M. The Worcester members will leave on train No. 745 at 8.36 A. M. The New York contingent will leave the Grand Central Terminal at 8.31 A. M. on train No. 8. This train will leave New Haven at 10.30 A. M. Upon arrival at New London, each group will go directly to the Mohican Hotel, where a "get-acquainted" luncheon will be served

Jan 10, 1916

By W. Spencer Hutchinson

THE relative importance of mineral production in British South Africa is about as follows: Gold, $200,000,000; diamonds, $40,000,000; coal, $18,-000,000; asbestos; $3,000,000; chrome ore, $2,000,000. In 1926 the gold mines paid $42,000,000 in dividends, the diamond mines $13,000,000, coal nearly $3,000,000, others less than $500,000. The recorded history of South Africa starts with the visits of the Dutch and the English in the sixteenth century, followed by the settlement of Cape Colony by the Dutch East India Company in 1651: The English acquired Capetown in 1806 and conflicts between English and Boers were a part of the history, from that, time on. Transvaal was settled in 1835, following the Great Boer Trek. The mining of diamonds became im-portant in 1870; the production of gold from the Rand in 1890;' the export of chrome ore in 1910; and the dis-covery of platinum in 1925. South Africa has a race problem, resulting not alone from the disparity of numbers between whites and natives, more than seven blacks to each white, twenty to one in Southern Rhodesia, and three. hundred to one in Northern Rhodesia; but because of the division of the white race between English and Cape Dutch or Afrikaans. The natives are also of many tribes.

Jan 6, 1927

By Randall L. Neal

This paper discusses the impact of taxes at the state and federal level on typical on-shore oil and gas exploration economics in the USA. Taxes considered are the windfall profits excise tax, state production (or severance) taxes, state income tax, and federal income tax. Also considered will be market prices for oil and gas in the USA. The effect of government take as a percent of revenue, on rate of return, discounted Payout, and discounted cumulative cash flow is shown on the attached tables. The conclusion drawn is that tax laws, while rarely the most important factor to be considered when drilling a well, can have significant impact on the profitability of oil and gas ventures, and should be considered when determining where to drill. Hypothetical exploration wells were analyzed for the impact of tax laws on project profitability. The results of this study show that when factors other than taxes are postulated to be the same (such as producing rate, capital, operating costs, and prices), cash flow can vary by as much as 68% due to the differences in the tax laws. Other significant findings for the cases studied include: (a) that discounted payout varied by as much as 1.8 years, (b) that rate of return differed by up to 67% and (c) the total tax rate as a percentage of revenue had a maximum variance of 33%.

Jan 1, 1982

By George W. Maynard

In the course of an examination of some of the California hydraulic mines in November last, I visited the property of the Gold Run Ditch and Mining Company, near Dutch Flat, Placer County. This is one of the most important and extensively worked mines in the district. The gold occurs in the characteristic blue gravel, which averages 175 feet in thickness, the lower 40-60 feet being made rip of cement gravel, which resists the action of water, and can only he loosened by blasting. The specimen which I have the pleasure of laying before the members was presented to me by Mr. I. L. Gould, the intelligent superintendent of the mines, who informs me that he found it in the old river channel, about twelve feet above the bedrock. The flattened water-worn nugget of gold, about the size of a kidney-bean, is imbedded in blue cement gravel, around which quartz has crystallized. When found the projecting portion of the nugget was enveloped in quartz, the core of gravel and gold having only been discovered after breaking the lump of quartz. On the quartz there is a shell of cement. The specimen is a remarkable confirmation of the theory of the deposition of quartz from solution. DISCUSSION. Dr. T. STERRY HUNT, in commenting upon this occurrence, remarked that it is in accordance with what we already know of the recency of some of the quartz of this region, and cited the microscopic

Jan 1, 1880