Search Documents

By R. L. Huntington, D. T. MacRoberts, Charles R. Hetherington

Since the equation of continuity governing transient flow of gases through porous media cannot be integrated mathematically into a simple usable expression free from series terms, empirical and approximate equations have been advanced relating cumulative production and future production rates from gas reservoirs with time. In order to check the accuracy of these empirical equations and to obtain an insight into the initial conditions pertinent to the solution of the fundamental equation of continuity, experimental work has been conducted on a vertical 2-in. tube, 91.6 ft. high, packed with unconsolidated Wilcox sand. The results presented in graphical form show the accuracy of the approximate relations. Data from unsteady-flow runs on the 2-in. experimental tube are presented graphically, and are applied to obtain an equation for this specific case, and are offered as an aid in future investigations of this basic equation. The close agreement between equations calculated for steady-state flow and the experiments indicates that the decline of actual gas reservoirs may be treated by an application of these equations without serious error. Introduction The steady-state flow of gas through a porous material—that is, flow wherein the boundary conditions do not vary with time—is subject to analytical solution. Muskat1 has shown that the general differential equation is simply the La Place equation in P2. Direct solutions may be at once obtained. The unsteady state, on the other hand, is not analytically reducible. Since nearly all phenomena of practical interest in gas production involve flow in the unsteady rather than in the steady state, it has been necessary to derive approximate Solutions to the general equation. The validity of such approximations has not hitherto been adequately tested. In the experiments to be described a simple, closed, linear system is substituted for the real complex gas field. The general results, however, are independent of the geometry Of the system' The problem studied is the rate of production, and the accompanying variations in pressure, when one end of a linear porous system is opened to the atmosphere and permitted to produce to exhaustion. An approximate solution to the general differential equation, based upon the assumption of an "infinite series of steady states," is then applied to the results to determine the validity of this method of dealing with actual reservoirs. Theoretical Considerations The fundamental differential equation governing the flow of a gas through a Porous medium can be derived easily from the equation of continuity, Darcy's law, Boyle's law and a statement of the thermo-dynamic nature of the flow. For isothermal flow it is: d2P2/dx2 + d2p2/dy2 + d2p2/dz2 = 2fµ/K dP-dT

Jan 1, 1942

By R. N. Stevens

GRAIN boundary sliding plays a part in the high-temperature deformation of polycrystalline solids, and many investigations1-11 have been carried out to determine the deformation contributed by this mechanism. The principal method employed has been to measure one of the components of the grain boundary displacement, see Fig. 1, at a large number of boundaries, and from the mean value so obtained to calculate the elongation contributed by sliding. A formula connecting these mean values and the elongation contributed is evidently required, and many have been derived. They are usually of the form where Egh is the tensile elongation contributed by sliding, is the mean value of the component, x, N is the mean number of grain boundaries intersecting a line of unit length, and K is a dimensionless parameter known as the averaging factor. Table I summarizes the equations used by various investigators. Examination of these shows that their derivations usually involve doubtful assumptions, and are often in serious error. The purpose of this note is to point out that rigorous solutions to the problem of calculating Egb from x have been available in the literature for some years.' Since this is so little known, and also the original derivations do not make some important points clear, it is proposed to rederive the basic equations. These will be extended further, and the conditions in which the extended equations may be applied will be indicated. The mean values of the components of the sliding vector (I, d, and I:, Fig. 1) will depend on the method by which boundaries are sampled in order to make measurements.3,11 Boundaries are usually sampled by marker lines parallel to the stress axis, or lines perpendicular to the stress axis, the measurement being made at the point where the marker line intercepts the boundary. We will denote the mean values determined by these various sampling methods as follows. lT, dT and vT are mean values obtained by making measurements at pointswhere a transverse line intercepts the boundary while lL, dL, and vl, are the mean values from a longitudinal line. The number of boundaries per unit length also may depend on the direction of measurement, and so we define NT and Nl to be the number of boundaries per unit length, after creep, in the transverse and longitudinal directions, respectively.

Jan 1, 1967

By E. W. Krampert

The oil industry was very active in Wyoming in 1936, in contrast to the several quiet years preceding. Production for the year again increased about 7 per cent, following an 8 per cent increase in 1935. During the year, 85 oil wells were completed, compared to 55 in 1935. Three gas wells were completed in 1936, and three in 1935. At the end of the year 45 wells were drilling, as compared to 55 drilling at the end of 1935. Two new oil fields and one new gas field were discovered in Wyoming during the year. In the year 1936 Wyoming produced 14,475,431 bbl. of oil, a gain of 1,001,081 bbl. over the 1935 figure of 13,474,350. This increase, in the main, was due to the taking of light oil from the newly developed Sundance sand pool at Lance Creek, and from the new fields, Quealy and Medicine Bow, which contributed their first production this year. Most of the other old fields either were partly shut in in competition with the new fields, or showed a normal decline. This was especially noticeable in the black-oil fields, where production had been slowly but steadily increasing for a number of years. During 1936 black-oil production decreased approximately 100,000 bbl. as compared to 1935. The only black-oil field to show marked increase was Garland, which managed to take the market from less favorably located fields. The production of Wyoming in 1936 was 11,358,757 bbl. of light oil and 3,116,674 bbl. of black oil. Salt Creek, with a production of 6,015,000 bbl., is still the largest single oil-producing field, accounting for 42 per cent of the year's total production. Lance Creek, an old field, with newly developed production in the Sundance sand, reached second place this year for the first time in its history, with a production of 1,878,486 bbl. Lance Creek production will almost equal that of Salt Creek in 1937, if the present rate of production is maintained during the coming year. Oregon Basin, a large black-oil field, held second place in 1935, but owing to a greatly lessened demand for its production, dropped back to third place in 1936. This was in part due to greatly increased light oil available, and in part to the greater supply of black oil available at

Jan 1, 1937

By Henry Drinker

The Institute has lost a valued member by the death of Eckley B. Coxe, Jr. He bore the name of one who was largely instrumental in founding the Institute, and to whose support and guidance as active member, Vice-President, and President, the Institute owes. much. Eckley B. Coxe, Jr., was the nephew of the late Eckley B. Coxe. He held a large interest in the coal estates owned and developed by his family, and he was thus naturally led to take a continuing interest in mining matters, and for years and up to the time of his death was a full member of the Institute. He died at his residence, Drifton, Pa., on Sept. 20 last, aged 44. He was a member of the class of '93 of the University of Pennsylvania,. of which great institution he was a devoted alumnus. His educational and charitable activities were numerous, but his chief life-work and interest was in archeological investigation and research in Egypt, carried on through the Museum of the University of Pennsylvania of which Museum he was President. The discoveries made by the various expeditions financed and directed by him, and the notable publications issued by his direction and at his expense, chronicling the results, are among the most important researches ever made of buried Egypt. Mr. Coxe was a member of the International Historical Society and of many educational and charitable organizations. By his will, among other bequests, he left $500,000 to the Museum of the University of Pennsylvania and $100,000 to the University, the income of the latter fund to be applied to increasing the salaries of the professors of the Institution. He also left $100,000 to the Children's Hospital of Philadelphia, of which he was a manager, and in addition thereto $10,000 of which the income is to be applied in providing Christmas presents for .the child patients, and in providing an annual dinner for the patients and attendants of the hospital. He bequeathed $50,000 to Leonard Hall, an associate mission of the Episcopal Church, at South Bethlehem, Pa., $25,000 to the Epileptic Hospital and Colony Farm (Philadelphia) ; $50,000 to the Philadelphia Orthopaedic Hospital and Infirmary for Nervous Diseases; $15,000 to the United Charities of Hazleton, Pa., the income to be applied to the salaries of nurses; and $25,000 to the Mining and Mechanical Institute of the Anthracite Coal Region of Pennsylvania, founded by his uncle, Eckley B. Coxe, and of which Eckley B. Coxe, Jr., was an active trustee up to the time of his death. This Institute is known as one of the best preparatory schools for technical education in Pennsylvania, and is mainly devoted to extending an opportunity for education by day and night schools to the boys and young men of the Anthracite Region. Its principal is an alumnus of Lehigh University; it has an able local Board of Trustees, and an Advisory Board consisting of the Provost of the University of Pennsylvania, the President of Lafayette College, and the President of Lehigh University, all three of which institutions have established prize scholarships in the institute. Mr. Coxe carne of a distinguished ancestry, the record of which is fully given in the biographical notice of his uncle, Eckley B. Coxe, by Dr. R. W. Raymond, in Vol. XXV of the Transactions.`

Jan 12, 1916

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By Walter Miller

The remarkable strides which have been made in recent years in the art of petroleum refining are not fully apparent until we attempt to compare the scientific status of the industry today with the basic conditions existing a decade or so ago. The spotlight has played so strongly on the development of cracking that many of the wonderful steps brought about in other departments have crept upon us unawares. A number of causes have contributed to this highly accelerated rate of progress. Constant effort by both companies and individuals to obtain the honors and prizes rewarding new discoveries has played its usual important part in our industry as in others. Competition has applied its continuous pressure on the refiner to reduce costs and losses and increase the proportionate yields of the higher-valued fractions. Advances in the engineering professions and growth in chemistry and allied sciences have contributed much. But there are other factors which deserve particular mention. The rapid development of the internal combustion engine, with the rigorous quality requirements and large quantity consumption of both fuel and lubricants has been a tremendous influence in adding impetus to natural progress. The teaching of petroleum principles and practices in many of our best universities and technical schools, and the calling into the industry of ever greater numbers of scientifically trained men to supplement the efforts of the practically trained operators, as well as to apply at close hand the fundamentals of science as a life work, has had and is having an incalculable influence. Important Improvements Let us consider briefly some of the most important improvements: First, distillation, which constitutes the greatest single phase of refinery operations, even with cracking excluded; that phase of distillation being handled as an individual subject in this symposium. Today we are distilling crude oil and redistilling by-products at a rate very much faster than was possible with the lesser knowledge of the art which we possessed

Jan 1, 1927

By Leonard B. Griffiths

In a recent communication, Smith and Wood described some results of 800°C compression/creep tests on WC-12 wt pct Co alloys in which plastic flow in the WC particles was believed to have occurred. The deformation observed in the WC particles was found to be a function of the rate of loading. The authors suggested that their data constituted support for the Ansell6-Lenel theory of yielding in dispersion-strengthened alloys. I do not agree with this interpretation since the Ansell-Lenel theory does not apply to the type of alloy in question. In this alloy, the dispersoid is present to the extent of about 80 vol pct. Even where there is no continuous skeleton, which apparently is the case in this instance, the simple fact is that nearly all of the load is carried elastically by the stronger material (wc).7 The constraint imposed upon the matrix, by virtue of the differences in Young's modulii and Poissons ratios, severely limits the stress level to which it may be subjected (assuming that the interfaces remain intact). If one allows for the constraint and then performs the same computation as in Smith and Wood, one finds that the stress on a WC particle is about 4 x 105 psi. This is about 21/2 times lower than the predicted fracture stress for WC. I would completely agree with the final paragraph of Smith and Wood, namely, that loading rate is of considerable significance. However. a more likely interpretation of their data is, I submit, that in the absence of stress relaxation (by secondary slip or climb) those WC-Co interfaces subjected to a normal tensile stress begin to fail. Once this occurs, the stress distribution will change rapidly and "premature" fracture of the WC then becomes quite probable. Tne serrated edges shown in Fig. 1 may very well be fine, interface fissures.

Jan 1, 1970

By C. F. Seaman, R. G. Clay

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By R. G. Clay, C. F. Seaman

The mines of The Tennessee Copper Co. are in the Ducktown Basin, in southeastern Tennessee. The ore is a heavy sulphide consisting principally of chalcopyrite, pyrite and pyrrhotite and in places running as high as 95 per cent sulphur and iron. Operating mines are the Burra Burra and Eureka. Development ' of the Boyd ore body was started in 1940. Late in 1939 the decision was made to change from fuse and cap to all electric blasting and at the same time electric cap lamps were installed to replace carbide. These changes were made to improve the safety and working conditions in the mines. Both the Bureau of Mines and explosives manufacturers recommended electric blasting as a safety measure. Until that rime, electric blasting had been used only for shaft sinking and in places where it was absolutely essential for safety. Very few men had had experience in this type of blasting, as the places where it was required were those that also required direct supervision. It was necessary for the mining staff to work out methods, procedure, and equipment to be used. In this they were ably assisted by representatives of the explosives manufacturers. Many mistakes were made and it is the purpose of this paper to describe the original plan and installation, show the major difficulties encountered. the remedies applied, and present the practices now being followed. Comparison of costs of the two methods will also be discussed. About six months were required to make the change and eliminate fuse and cap blasting entirely. The first electric blasting stations were installed in November 1939 and the last fuse was taken underground in May 1940. A very unusual condition forced the use of fuse for a short time in one heading after May, but that will be discussed later. Original Equipment and Installation A power line is generally recommended as a source of current where permanent blasting stations are used. The plan worked out for electric blasting was to tap 220-volt alternating-current lines when they were available and use 250-volt direct current from the trolley wire at all other places. A blasting machine would be available at each shaft for places where there were no regular blasting stations and could be used if a regular station should fail. The equipment decided on was No. 16 duplex reinforced lamp cord for lines to within about 50 ft. of the working place and No. 20 lead wire from that point to the shots. An open double-pole, double-throw switch with slate base was put in the circuit, so connected that the down position would close the line to the shots 2nd the up position would connect it to the Iine from the power contactor. This switch was located in the circuit as close to the blast as was safe (should the shots explode when it was placed in the shooting

Jan 1, 1943

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

By Dan Crackel, G. G. Ramos, Mark Heisel

INTRODUCTION Feasibility studies indicated that a cratering type stoping method was best suited to the character of the first ore block at Carr Fork. This method known as vertical crater retreat (VCR) has since been modified to a combination cratering and deck blasting using VCR drop raises for initial undercut development . The modified form retains many of the advantages of VCR while allowing high tonnage production blasts which have offset many of the disadvantages. FIRST CONCEPTS AND PREMISES Geologic Considerations The Steep Highland Boy (SHB) skarn orebody, the first of several blocks being developed, is a steeply dipping 70° to 90° limb of a syncline, with a width averaging 25 m (82 ft). The bed has a consistent east-west strike length of over 400 m (1300 ft) and extends from the surface to depths of over 1000 m (3300 ft). The footwall is highly fractured quartzite and the hanging wall grades from garneti te to limes tone and hornfe 1s. Because of the limestone in the hanging wall, the hanging wall appears more competent than the footwall. The ore is garnetite with lenses of massive sulphide and magnetite. The quartzite footwall is highly fractured not only because of the bedding but also due to the folding and intrusion of the quartz monzonite. This irregular footwall outline of some stopes in- creases the likelihood of excessive dilution. The principal ore mineral is chalcopyrite with some bornite. The garnetite ore is quite variable in terms of compressive strength and drillability. In addition to the sulphide and magnetite lenses, it is transected by clay- altered dikes and major and minor north-east faults. TABLE (1) gives the range and mean strengths of the rocks. Investigating Mining Methods Initial consideration of a suitable mining method centered around maximum safety and efficiency with minimum potential dilution. The following major methods were considered and investigated. Cut and fill mining was eliminated because of low productivity, the cost and problems associated with providing fill, and the relatively unsafe nature of the method. Sublevel caving was rejected due to the unpredictable cavability of the waste and the geometry of the ore body. Conventional sublevel or blasthole methods require excessive development, as fan and ring drills are limited to efficient drilling in the 18 to 25 m range (60 to 80 ft). Mining downdip with equipment drilling small diameter holes would have required eight separate extraction/drill horizons with crosscuts and associated excavation in the main ore block. The use of down the hole (DTH) machines cap- able of drilling 165 m (6g in) diameter holes

Jan 1, 1981

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By P. B. Butler

IN common with others, the zinc industry found itself after the war largely over-capitalized, a condi-tion which still exists notwithstanding that Tri-State production has doubled since prewar days. This is partly due to the abnormal war demands and partly because of the war impetus given to research, a stim-ulus that because of its success has persisted (and probably will persist) constantly since then. Improved practice and metallurgy resulting from research are today responsible for an increased pro-duction in the Tri-State district of 15 per cent over the practice of five years ago, and the giant strides in this respect in the western states together with the more moderate advance in the Tri-State district has thrown out of equilibrium the more or less balanced production of before the war and production has con-sequently gained on consumption, a condition resulting in rapidly narrowing profits in the Tri-State field, where the present average cost is actually greater than the price received for our product. Despite this condition, no thinking person will de-plore the cause or means used to achieve a greater production and, as this progress is merely the economic application of intelligent thought, it follows that equal effort and thought may be expected to produce the remedy. It has been suggested that the practical application of research has resulted in less need for man-power and consequently in the lessening of employment to common labor and to engineers. I cannot think that such is the case although personally I have received more ap-plications for employment during the last two years than ever before. But when one considers the strides production of all commodities has taken, it is difficult to reconcile this immense development with the possible increase in pop-ulation especially in view of our stringent immigration laws. Whether or not improved industrial methods are responsible for the lessening of employment the ques-tion as to the wisdom of such improvement is hardly debatable. While the Tri-State district of Oklahoma, Kansas and Missouri continues to be the leading factor in the zinc¬mining industry, gradually lowering prices during 1925 and 1926 and a. decided drop during 1927, have de-creased its production almost 20 per cent, this tonnage having largely been replaced by western concentrates.

Jan 4, 1928

C. H. WILSON,* New York, N. Y. (written discussion?).-On page 2680, under the heading Junction Box and Zone Box, the authors say, with reference to the zone-box principle of connections between primary couple, compensator couple, and copper leads, which method in its appli-cation to a single couple is shown in Fig. 34, that if this principle is adopted for a multiple installation, so as to save compensating leads; a selective switch may be (and the inference is that it must be) inserted between the zone box and the different couples, putting the switch at an inconvenient point, or putting up with some complicated interlacing of connections.. Wilson-Maeulen Co. has employed the zone-box method extensively for several years and in none of the many multiple installa-tions has either of those alternatives been resorted to. Instead there has been used a method of wiring with the switch at the indicator and involv-ing no more complications than the junction-box method shown III

Jan 11, 1919

By A. H. Lindley, Fraizer M. Stewart

For many years large mining companies were able to finance nearly all of their capital requirements from internally generated funds. However, during the last decade, funds needed for capital expenditures, dividends, and scheduled debt retirement have grown faster than cash flow. As a result the minerals industry has had to rely increasingly on other sources of funds. Getting the capital for new mining projects is a challenge, particularly for smaller companies. New methods of financing and new variations to old methods have been developed and more are needed. Commercial banks are short-term lenders. By policy their loans are limited to low risk loans-those made solely on the borrower's general credit, and secured loans where cash flow is sufficient to provide repayment within a comparatively short term. To maintain liquidity, banks prefer to make loans of less than seven years' term. If a longer loan is needed an insurance company or pension trust may take the long-term part.

Jan 1, 1971

By P. J. Burkhardt, L. V. Gregor

The oxidation kinetics of single-crystal silicon has been investigated using extremely dry oxygen as the oxidant. Two techniques were used. The first involved a flow system with which incremental thickness measurements were made. This sytem provided an oxygen ambient at atmospheric pressure which had a moisture content of less than 0.1 ppm of water. The second technique involved measuring the change in volume of oxygen with time in a closed system. A temperature range of 900O to 1200 "C and a pressure range of 20 to 760 Tory were covered. Both techniques showed that a simple parabolic rate law holds only at the higher temperatures. At lower temperatures, the data up to 5000Å can be fitted well to a linear-parabolic equation. The two constants in this rate equation are examined in terms of a physical model. The parabolic portion of the low-temperature oxidatLon fits along the high-temperature curve of an Arrhenius plot. The parabolic rate constant for the flow-system technique can be expressed by k = 2 x 10-9 exp (L 31 kcalRT) sq cm per sec. The manostatic technique gave k = 1 x 10-exp (- 23 kcalRT) sq cm per sec. By extending the thickness range to over 104. a rate law of X = At seems to fit all of the data better than the linear-Pavabolic law. Here the exponent n increases from 0.518 at 1150 V to 0.637 at 900°C. PASSIVATION of silicon planar devices through thermal oxidation is of such great importance that considerable effort has been devoted to the study of the process.17 Much of this work involves hydrothermal oxidation, in which H2O is the oxidant: whereby H2 is produced. It has been proposed that the reaction proceeds by the formation of Si-OH groups and hydroxyl diffusion through the film to react with the silicon surface. Thus, the silicon oxide layer probably contains residual hydrogen in some form after oxidation in H2O and it has already been established that hydrogen has a marked effect on the electronic properties of oxide-passivated silicon surfaces. Silicon is oxidized by oxygen at elevated temperatures; but the rate of oxide formation is considerably lower than that for 0." By using dry O2 as the sole oxidant, the presence of residual hydrogen is presumably avoided. At present, the mechanism of thermal oxidation by dry O2 is a matter for conjecture, and the presence of small amounts of H2O was reported to have a marked effect on the rate of oxide formation10 (perhaps on the electronic properties of the surface, as well). Hence, this study of the kinetics of silicon oxide growth in 0, was undertaken: 1) to determine the oxidation rate at atmospheric pressure in a system designed to exclude rigorously all traces of H2O in the ambient 0,; 2) to obtain oxidation-rate data in situ in dry O2 by means of a continuous monitoring of the amount of 0, consumed during oxide growth. These objectives are complementary—the first assesses what effects (if any) are obtained by excluding H2O from the reaction, and the second expands this information while at the same time avoiding the uncertainty inherent in relying upon incremental measurements of oxide growth to furnish kinetic data. EXPERIMENTAL PROCEDURE The conventional silica open tube in a resistance-heated oxidation furnace is subject to sources of trace H2O, even after the input O2 is thoroughly dried and the outlet gas stream is passed through a trap to prevent

Jan 1, 1967

By W. W. Anderson

A formula for quantitative efficiency is proposed, in which the efficiency value is a function of the improperly distributed material at the gravity of separation effected by the cleaning equipment. The misplaced material is expressed as a percentage of the total material discharged from the equipment. Numerous examples are given, demonstrating application of the formula to various types of separation, including multiple-product separations.

Jan 2, 1950

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455' C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.' There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By J. C. DeHaven, Harry Seltz

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455' C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.' There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935