Search Documents

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By Raymond Mancha

When calculating the pressure-volume characteristics of projected mine-ventilating circuits by orthodox methods, certain basic assumptions are required in order to employ the various available empirical data. It is assumed, for example, that the mine air is an incompressible fluid subjected to isothermal flow, an assumption sufficiently accurate for practical purposes since pressure and temperature differentials are small throughout the average circuit. A more erroneous assumption, however, is that all air is accounted for as it travels throughout the mine. No attempt is usually made to evaluate stopping leakage as it occurs; instead, the air volume required at the last crosscuts is assumed to enter the mine, travel the various intake air courses intact, sweep the workings and travel out by the return air courses to the point or points of exit from the mine. Actually, there is a leakage of air from intake to return at every stopping, the quantity of this leakage depending upon the tightness of the stopping and the pressure difference across the stopping. Unfortunately, a lack of empirical data and knowledge of the condition of individual stoppings makes an exact analysis of underground stopping leakage impossible. Generally, leakage is most severe through the old stoppings outbye the circuit. These are also subjected to higher pressure differences than the newer inbye stoppings. Therefore the circuit air volume diminishes at a decreasing rate progressing from outbye to inbye the circuit. Consider a simple mine circuit consisting of one intake and one return air course, each of equal and uniform section area and interconnected at regular intervals with crosscuts equipped with stoppings. At any point X inbye the circuit the air volume q on the intake air course equals that on the return air course and decreases with diminishing rate from outbye to inbye the circuit between the limits of Q1 completely outbye and Q completely inbye. Such a volume change is represented by curve a, Fig. I, which is computed with the aid of the equation q = Q1- (Q1- Q)(X + L)N. This equation results from the general algebraic equation of form q = k, — kXN after solving for kl and k with the knowledge that completely outbye X = o and q = QL, also completely inbye X = L and q = Q. Curves a, b and c, Fig. I, show values of q as ordinates versus values of X as abscissas, for values of N equal to 0.50, 1.00 and 2.00, respectively. Distribution of underground stopping 1eakage directly affects the air-volume distribution along the circuit, which in turn determines the circuit pressure gradient. To deliver any required air volume inbye a circuit or portion thereof requires a higher circuit-pressure differential if stoppings leak than is necessary with tight stoppings. Every mining engineer engaged in the analysis of projected mine-ventilation circuits is therefore confronted with the problem of making proper allowance for the effects of leaking stoppings. The purpose of this paper is to present evidence in support of the author's suggestion that circuit pressure increase (per cent)

Jan 1, 1942

By R. H. Moore

The data for diffusion in dilute binary alloys with the Solvents Ag, Cu, Ni, Fe. Al. and Pb hare been correlated as a function of atomic volume. Linear equations of the form: Q = b - a log V are obtained with constants "a" and "b" ciuirac-teristic of each solvent metal. In most cases. 3-d In recent years measurements of diffusion coefficients in solid binary alloys. using small concentrations of radioactive isotopes. have resulted in accumulation of highly reproducible data. Such and 4-d transition elements correlate on separate straight lines from those which serve to correlate the non/ransition elements. The data for the uon-transilion elements diffusing in silver and copper liave been fitted by least-squares analysis. It is concluded that the size and charge effects which determine the magnitude of the activation energy for diffusion are a function of atomic volume. systems represent the simplest possible examples of chemical diffusion since solute interaction effects can be neglected and Kirkendall-like phenomena do not occur. Generally it is found that thc diffusion rate of the solute is within an order of magnitude of the diffusion rate of the solvent. The differences have been attributed to the effect of size and to electrostatic interactions between the solute and solvent atoms.

Jan 1, 1965

By Walter Weeks

THE subject of the flow of air through a mine under the influence of natural ventilation has proved an elusive one. To my knowledge only cut and try algebraic solutions have been used where multiple paths are involved. The object of this paper is to present a method for the graphi-cal determination of the flow induced by the natural ventilation pressure (N.V.P.) alone or in combination with a fan. The N.V.P., measured in pounds per square foot, induced by two columns of air between two horizontal planes at different elevations, is equal to the difference in weight of the two columns, assuming each to have a cross-sectional area of 1 sq. ft. Pressure in pounds per square foot is converted into inches of water by dividing by 5.19. Methods of calculating the N.V.P. have been discussed in the litera-ture. In this paper, for simplification of exposition, the change in pres-sure due to the weight of superimposed air will be assumed directly proportional to the length of the column. The actual methods of cal-culating the N.V.P. do not affect the solutions to be presented. It must be realized that the precision to be obtained from the small-scale, inked diagrams presented is not as great as would be obtained from large-scale, penciled curves that would he used in practice. The accuracy of the curves does not warrant reading "volumes" closer than the nearest thousand cubic feet per minute.

Jan 1, 1938

By A. C. Halferdahl

DURING a study of reactions involving iron sulfides, it became desirable to know approxi-mately the heat of decomposition of pyrite. The values given for the heats of formation of pyrite and ferrous sulfide are 35,500 calories and 23,070 calories respectively. For the reaction 2FeS2= 2FeS+S:, the heat effect would be-24,860 calories. But pyrite gives sulfur and pyrrhotite upon heating and the latter is a solid solution of sulfur in ferrous sulfide. The only meas-urements of this decomposition are those of Allen and Lombard1 of the Geophysical Laboratory who have measured dissociation pressures of both covellite and pyrite and have carefully reviewed the literature. They give a table of values for covellite as determined by Preuner and Brockmoller2 and by Wasjuchnowa3 and compare these values with their own measurements. The conclusion is that the measurements of Preuner and Brockmoller are seriously in error, while Was-juchnowa's values fit in well with those of Allen and Lombard. Wasjuchnowa's measurements were made by a dynamic method, while Allen and Lombard em-plowed a static method on both covellite and pyrite. Tables I and II reproduce the measurements of Wasjuchnowa and of Lombard and Allen on covellite and pyrite.

Jan 11, 1927

By R. H. Barham, G. W. Nabor

Linear aquifers, either limited or essentially infinite, may be encountered in reservoir engineering practice. In areas where faulting fixes reservoir boundaries, the fault block reservoir may have an aquifer of limited extent whose geometry is best approximated as linear. An infinite linear aquifer can occur as a regional feature whenever water movement through the aquifer member is constrained to one direction. Such constraints can arise from major faults, facies changes or pinchout of the member. Miller* pointed out that linear aquifers have received only meager attention in the past. He analyzed the performance of finite and infinite aquifers, developed working equations and curves, and presented examples. While Miller's curves may be used fairly easily, a separate one is required for each size of aquifer. In this paper, Miller's equations have been used as a starting point. By modifying them slightly, they can be reduced to a form which yields a single working curve, applicable to any size of aquifer. Thus. interpolation between curves is eliminated and accuracy is improved. Miller's results for finite aquifers covered only the boundary condition of no flow across the outer aquifer boundary. This paper also includes the case of constant pressure at the outer aquifer boundary.

Jan 1, 1965

By H. A. Deans

A three-parameter mathematical model for one-dimensional flow in porous media is developed. The objective of the model is to predict accurately the longitudinal dispersion associated with the flow of either gases or liquids over a wide range of Reynolds number. A qualitative analysis of the model parameters is given. Published experimental pulse-response curves are compared with results predicted by the model. Several general types of problems are given for which the model can be used. INTRODUCTION The problem of multicomponent single-phase flow through porous media is encountered in the study of petroleum reservoirs, gas chromatographic and ion-exchange columns, industrial fixed-bed con-tacters and elsewhere. These particular examples span the wide range of flow conditions possible; Reynolds numbers of less than l0-4 are not unusual in oil-production problems, while values in excess of 103 are common in large fixed-bed operations. The study of flow-dependent transport phenomena is complicated both by the changes in the character of the flow over this range, and by the irregularity of the flow boundaries inherent to porous media. Dispersion is one of the important phenomena known to depend fundamentally on flow conditions as well as on fluid and medium properties. As used in this paper, the term "dispersion" refers to the observed mixing of fluid elements of different composition which occurs in flow systems. The actual mechanism may be one or more of a number listed below. Only dispersion in the direction of the mean flow (referred to as axial or longitudinal dispersion, or mixing) is considered here, although lateral dispersion arises as part of certain coupled mechanisms. MECHANISMS FOR LONGITUDINAL DISPERSION A number of distinct mechanisms are known3,5,7,8 to contribute to the phenomenon of longitudinal dispersion. The more important of these are as follows. 1. Molecular diffusion in the flow direction. 2. Turbulent (cell) mixing. 3. Lateral transport processes coupled with velocity and/or residence time distributions, including: (a) "Taylor" diffusion caused by the interaction of velocity profiles in individual voids with lateral molecular diffusion; (b) separation and remixing or interdiffusion of streams having different velocities around particles; and (c) the couplipg of gross velocity profiles, caused by viscous instability or inhomogeneous porosity, with lateral dispersion. 4. Finite mass-transfer rate between a porous matrix and the flowing phase, and finite diffusion rate inside elements of the porous matrix. It is a well documented fact that these mechanisms, whether acting individually or in combinations, produce essentially similar integral effects. The observed dispersion can be described approximately by solutions of the diffusion equation with a properly chosen dispersion coefficient. Necessary conditions for equivalence between dispersion and diffusion are discussed by Klinkenberg and Sjenitzer.7 Apparently these conditions are not satisfied exactly in many real systems. "Best fit" solutions of the diffusion equation often depart appreciably from measured breakthrough curves for the usual pulse- or step-forced experimental systems. In particular, pulse response curves usually show some degree of asymmetry and "tailing" which cannot be reproduced by the one-parameter diffusion model. The three-parameter model proposed herein attempts to produce these effects in a realistic manner. Asymmetry and tailing are predicted for certain sets of parameter values, while for other sets the new model agrees with the diffusion model. VELOCITY DEPENDENCE OF DISPERSION Molecular diffusion apparently controls at sufficiently low Reynolds number in both gas and liquid systems.*l3 At Re > 20, turbulent cell mixing is dominant for gases flowing at low pressure; the data of McHenry and Wilhelm8 show that the mixing cell is approximately 1 particle diameter long in random sphere packs. on the other hand, the data

By H. C. Chang, N. J. Grant

Creep of very coarse grained high purity aluminum was studied at 400°, 700°, and 1100°F at initial stresses of 50 to 1200 psi. Local strain measurements were made across the grain boundaries and in different regions of various grains during creep, thereby permitting the drawing of component creep curves. The relative amounts of elongation as measured across a grain boundary and in the grains adjacent to the boundary depend on the temperature of testing. The significance of creep curve equations and activation energies is discussed. THIS paper presents some of the results of a research program devoted to the study of the mechanism of creep in high purity aluminum. Previous publications have dealt with the cyclic processes of alternating grain boundary sliding and migration, and the deformation in the grains caused by these processes;' the direction and the driving force of grain boundary sliding and migration;' the deformation in the grains and the restricting effects of the grain boundaries on this deformation." These previous papers were based mainly on either microscopic observations or X-ray data, or both. Sometimes creep curves across two closely spaced reference marks (about 0.6 to 0.7 mm apart) were also presented with a view to correlating the elongation values with the optical observations in general, and with certain deformation processes in particular. These curves shall henceforth be referred to as component creep curves. No attempts were made, however, to compare either the component creep curves which were obtained in different regions of a specimen, or those obtained from different specimens subjected to different creep test conditions. It is the purpose of this paper to present these component creep curves. Among the factors influencing the behaviors of these curves, those studied were stress, temperature, and grain arrangements in the specimens. It is proposed to show how greatly the deformation can vary from grain to grain and within an individual grain in a coarse grained specimen. The experimental technique and procedure have been presented.' It remains necessary to emphasize that the reference marks were produced by pressing a thin sewing needle into the surface of the specimen before the final annealing at 900°F for 24 hr and at 1150°F for 12 hr. The cold work around the needle indentations was therefore removed. The depth of these holes after electropolishing the annealed specimens was about 0.01 mm. This depth and area were negligible in comparison with the thickness of the specimens, 2.3 mm, and hence would not affect the creep behavior. Results Fig. 1 shows a development diagram of specimen P-8. The dots on the surface locate the needle point reference marks used to obtain the component creep curves. A curve obtained between two dots across a grain boundary measures not only the boundary deformation but also the deformation associated with boundary sliding occurring in the grains in the region between these indents. The original distance between two reference marks was about 0.6 to 0.7 mm. The maximum error of measurement was 0.01 mm, or in terms of percentage elongation, of the order of & 1.5 pct. Whereas the component creep curves shown in the figures to follow were drawn as a gross average of the points, in view of the fineness of some of the steps of grain boundary sliding and migration, as shown in the previous publications,¹,2 it appears logical to expect that some of the finer cycles of movement have not been delineated for the strain sensitivity of the measuring system. It seems justifiable to say that the curves are not as smooth as shown. 700°F Tests: Fig. 2 shows component creep curves across four of the grain boundaries in specimen P-8, tested at 700°F and 85 psi. These curves clearly show alternate cycles of increasing and decreasing

Jan 1, 1954

By J. R. Kyte, R. L. Dalton, V. O. Naumann, R. L. Ridings, R. W. Greene

This paper presents a one-dimensional numerical method for calculating dissolved-gas-drive behavior for a single well or a linear reservoir. Pressure and saturation distributions can be calculated, including the effects of capillary and gravity forces. The analysis has been programmed for solution on the IBM 7090 digital computer. A comparison of experimental and calculated behavior for two linear models demonstrates that the method is suitable for calculating dissolved-gas-drive behavior under reservoir conditions of flow. Dissolved-gas-drive tests were run, at different production rates and with oils of different viscosities, on short (6.ft) and long (173ft) flow models. For tests approximating reservoir pressure gradients and flow rates, there was excellent agreement between experimental and calculated results. A series of calculations of well behavior for thin, horizontal, homogeneous, dissolved-gas-drive reservoirs shows that ultimate recovery is independent of production rate or well spacing in such cases. These calculations also show that Muskat's method and similar material-balance analyses are not applicable under some conditions particularly for high pressure drawdowns. INTRODUCTION The problem of calculating dissolved-gas-drive reservoir performance has received a great deal of attention throughout the oil-producing indusfry for many years. Really significant advances, however, have been made only in recent years. The rapid evolution of high-speed computing equipment and techniques has opened up new approaches to the problem and led to realistic, quantitative analyses free of many of the assumptions and limitations of earlier methods. The one-dimensional numerical method described in this paper includes the effects of both gravity and capillary forces. A number of test calculations, based on different rates, spacings, and rock and fluid properties, have shown that the method is adequate for systems that can be reasonably represented by a one-dimensional model (linear or radial) and in which fluid segregation perpendicular to the direction of flow is not important. Along with the development of mathematical methods, an experimental program was conducted and the data were used to test the validity of the theoretical basis of the mathematical method. Linear models were used and all experiments were run using 1,000-psig bubble-point oils. The use of long, high-pressure models enabled us to more closely approach reservoir gradients and flow rates. MATHEMATICAL FORMULATION DIFFERENTIAL EQUATIONS The differential equations describing dissolved-gas-drive behavior in one dimension dare summarized here. They include Darcy's law for flow of oil and gas (Eqs. 1 and 2) and the equations for conservation of mass for oil and gas (Eqs. 3 and 4). The oil and gas pressures are related by capillary pressure (Eq. 51.

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By Richard T. Newcomb

Federal and utility industry research has largely ignored coal beneficiation techniques in the implementation of SOx control. This paper accepts the hypothesis that beneficiation cum scrubbing is the cheapest way for the vast majority of seams in the eastern coal provinces to comply with standards. Comparisons are based on point estimates of average beneficiation costs from a model of coal preparation (COBET) designed to simulate four levels of cleaning. The paper describes how economic theory can be applied to derive econometric supply functions from actual data on the geology of minable seams, washability and technical constraints. West Virginia is taken as an example of a producing region. Spatial supply functions are derived empirically from the engineering model simulations.

Jan 1, 1977

By A. C. Noble, D. E. Ranta

Orebodies with intricate three- dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer- assisted methods. 'The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral de- posits.

Jan 1, 1984

By William A. Johnson

THE fundamental role of diffusion in many reactions occurring in solid metals has long been recognized, and there have been careful measurements of rates of diffusion in numerous alloy systems, but our understanding of the atomic mechanism by which diffusion occurs is scarcely in an advanced state 1-3 It is doubtful that this mechanism can ever he directly ascertained, rather, all imaginable mechanisms must be examined and the one that is in best accord with such data as can be obtained from suitably chosen experiments should be selected Because of its relative simplicity, diffusion in a system containing only one kind of atomic species-commonly called self-diffusion-is of considerable theoretical interest It may be expected that diffusion theory will not be advanced appreciably until a wide variety of diffusion experiments-of which diffusion in a chemical concentration gradient and self-diffusion are two important types-are carefully performed and inter-compared Aside from the purely theoretical interest in self-diffusion measurements, such studies will be of considerable engineering importance The rate of any process in a pure metal requiring the movement of atoms, of which recrystallization and creep are two familiar examples, will be understood more readily with the aid of self-diffusion data † Self-diffusion implies the diffusion of something into its exact counterpart, the detection of such a process is patently impossible, and it is-necessary to substitute for it the diffusion of one isotope (in this case radioactive) into another isotope (in this case stable) of the same chemical element There is, however, no reason to suppose that a radioactive atom will not diffuse at the same rate as its stable isotope, for all of the isotopes of the same element have exactly the same chemical properties, neither the difference in nuclear energy nor the difference in mass would be expected to exercise an important influence in this phenomenon In this sense, self-diffusion may be thought of as the diffusion of radioactive atoms down a radioactivity concentration gradient, just as usual diffusion is the diffusion of one kind of atone down its chemical concentration gradient The first measurements of self-diffusion ii ere made by von Hevesy4-6 using the radioactive lead isotope thorium B in ordinary lead The recent development of means for producing artificial radioactive elements has made possible similar measurements on gold,7,8 copper,2,9 and zinc 10 11 Many of the data that have been obtained are rather poor, and no adequate reason has been given for their poorness, it appears, however, that the unsatisfactory results are characteristic of the particular experimental procedure employed, and not of self-diffusion measurements in themselves The experimental technique that has yielded the poorer results is the deposition of a thin layer of radioactive atoms on the surface of a specimen and the determination of the rate of inward diffusion

Jan 1, 1941

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

By Roy W. Wright

Introduction The title of my paper is satisfyingly broad and allows me to touch lightly or dwell at length on virtually any aspect of mining, while endeavouring not to trespass on the subjects of other papers to be presented. However, at this stage in our world history when for the first time we are beginning to take conservation and the welfare of future generations more seriously, I want to concentrate mainly on the question of whether or not there will be the resources of minerals available to sustain mankind's progress in the generations ahead. Metals and the Population Problem The supply of raw materials is of course only one of the fundamental problems that will face future generations: if we assumed that the world population would continue to increase at the present explosive rate, then I believe we can say with certainty that other fundamental problems of much greater significance would arise long before a shortage of raw materials - or other substitutes -had any impact on the progress of mankind. Thus, I must start this paper with the assumption that some equilibrium in population will be arrived at before these other problems overwhelm the world. Will the Metals Run Out? At the 75th Anniversary Meeting of this Institute in March, 1947, Clinton H. Crane, President of St. Joseph Lead Co., prophesied that for the next 100 years there would be enough copper, lead and zinc for every essential need. He defined a need as essential where the qualities of the metal in that use were irreplaceable. Today, except for one or two cases such as lead in lead-acid batteries, few metals have qualities that cannot be provided either by another metal or by another material. It is more a question of what the engineer or manufacturer is prepared to pay for special qualities as compared with using cheaper materials and perhaps a less satisfactory design.

Jan 1, 1971

By P. W. Gilles, B. D. Pollock

THE pioneering work of Steinitz1 and Steinitz, Binder, and Moskowitz2 has shown conclusively the existence at high temperature of two additional phases in the molybdenum-boron system and thus brings to a total of six the number of structures appearing in this system. To the structures Mo2B, MOB, and Mo2B5 they have added MO3B2, a new -MOB form, and have shown that MOB,, which has the same range of composition as Mo2B5, is only a high temperature structure of the latter. This solid solution, interestingly enough, includes neither of the compositions corresponding to the stoichiomet-ric compounds, MOB, or Mo2B5, but rather at all temperatures has intermediate values of composition. These workers have also, in the course of their work, measured melting points, transition temperatures, eutectic and peritectic points in the system and have shown that Mo3B2, because of its dispro-portionation at low temperature to Mo2B and MOB, is stable only in a limited high temperature range. During the course of the present work on the vaporization properties of the molybdenum-boron compounds, a few transition temperatures were observed. When the report of the other workers appeared, it was decided to repeat, in part, their study of the system. As a result, considerable evidence has been obtained that substantiates the specific kinds of melting processes they report as well as the general features of their diagram. However, a marked difference was found between the temperatures they report and the ones observed in this study, with the latter being higher. The purposes of this paper are to present the evidence obtained in this laboratory that verifies their diagram of the system, to give some important temperatures in the system, to compare them with those previously published, and to seek an explanation of the difference. Samples The metal starting material was 400 mesh molybdenum powder with a purity stated by the manufacturer to be 99.9 pct. The initial treatment, designed to remove volatile contamination, consisted of heating in a vacuum for 10 min to a temperature of from 800" to 1000°C during which a loss of 0.3 to 0.4 pct occurred. An assay following this treatment showed it to be 99.4 pct pure, with the principal impurity probably being oxygen. The boron starting material was obtained from the Cooper Metallurgical Laboratories and the Fair-mount Chemical Co. as 325 mesh powder with manufacturers' analyses of 99 pct or better. Initial treatment consisted of heating in molybdenum in a vacuum at about 1700°C for 10 min. During this time a loss of 3.5 pct occurred. An assay following this treatment showed the different samples to have purities ranging from 95.5 to 99.0 pct with iron and carbon as the principal impurities. Following the initial treatment, the elements were combined to form stocks of Mo2B and MOB by heating pressed mixtures in a vacuum to 1100" to 1200°C to accomplish reaction and to 1500" to 1900°C for a few minutes to evaporate the more volatile impurities. Analysis of the two compounds for boron by a modification of the method of Blumenthal3 and for molybdenum by the lead-molybdate method indicated them to have purities greater than 99 pct. The individual samples to be studied had compositions in the Mo2B-MOB range and consisted of mixtures of the stock compounds. Procedure As is usually the case in high temperature work the selection of containers for the samples posed some problems. For vapor pressure studies tantalum crucibles, allowing little contact with the pressed samples, were used and some of the observations made during these experiments are pertinent to the study of the phase diagram. Most of the experiments, however, were performed in graphite containers, as were those of the previous authors. Two kinds of spectroscopic grade graphite crucibles were used. One was a % in. cylinder, 3/4 in. high, containing seven 3/16 in. holes drilled 1/2 in. deep into which were packed samples of the different mixtures weighing 250 to 500 milligrams. The other, consisting of separate crucibles, was prepared by drilling 3/16 in. holes, 1/2 in. deep into 1/4 in. graphite rods % in. long. The 7/8 in. cylinder was heated directly by induction while the small crucibles were packed in a tantalum heating element for induction heating. All heating was done in a high vacuum system in which the pressure was generally less than 1x10-5mm and never rose above 2x10-5mm when the samples were hot. The general pattern of the heating in graphite was to heat rapidly to a temperature somewhat below the desired one, then to raise the temperature slowly. The samples were held for 2 to 5 min at the maximum temperature, which in all cases was far higher than that needed to produce reaction. The short time was employed to reduce possible contamination by the crucible material and to reduce composition changes that would occur because of vaporization. After examination following the heating, the samples were reheated to a higher temperature. Temperatures were measured with a Leeds and Northrup disappearing filament optical pyrometer, certified by the National Bureau of Standards, by sighting through a window at the top of the vacuum

Jan 1, 1954

* A demonstration pipeline for transporting coal will be constructed by Pittsburgh Consolidation Coal Co, at the Georgetown strip-mining operation near Cadiz, Ohio, The 12-in., 17,000-ft line, special crushing and preparation equipment, and pumps especially designed for the operation will cost about $550,000. A slurry of fine coal and water will be fed into the line and moved through it under pressure. * Sulphur resources in the U.S. are being rapidly exhausted with no new major deposits being found, This common mineral may become one of the most strategic items during the next five years. Recovery of sulphur from pyrites is being considered in case of an emergency. Already the British have adopted stringent measures to conserve sulphur supplies.

Jan 3, 1951

By Cornelius Kelley

VOLUMES have been written about the organizing genius of American industrialists. American methods of production are being studied by the manufacturers of other nations to ascertain the prac-ticability to foreign adaptation. Mass production and the mechanization of industry have become terms of popular understanding and significance. Our people think, act and talk in terms of economic nomenclature. Under these circumstances is it not a matter of supreme importance that Americans themselves should make an analysis of their own situation? National supremacy has been but a transitory event. Wealth has had no fixed abode, and commerce has followed no permanently established route. One hundred and fifty years, viewed from the abstract idea of time, is but a moment in the fact of continuous or successive existence, yet it measures. the cycle that has witnessed the growth of America from a struggling embryonic union of thirteen colonies estab-lished along the Atlantic seaboard to the nation of un-rivalled proportions, vast wealth, huge enterprises and productive energy that now exists beneath the protec-tion of and renders allegiance to the flag that but then had been created. To appreciate fully the significance of what has occurred, it is necessary that there should bee an understanding of the basic factors that have con-tributed so largely to the realization of our present situation. Among the most important were: First, the establishment of a government that was founded upon the principle of affording the widest pos-sible opportunity for individual effort and accom-plishment. Second, there existed a virgin territory of vast extent, endowed by nature with elements of potential wealth far exceeding that possessed by any other like area upon the globe.

Jan 8, 1928

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970