Search Documents

By Walter White

THE measurement of the reading of a thermoelement is the measurement of an electromotive force extraordinarily small compared to those generally used in commercial work. Of the various possible methods of measuring such a quantity, the most advantageous is always a delicate galvanometer. Since a galvanometer measures current, it is necessary to adopt some scheme by which its current reading shall indicate electromotive force. There are two general methods of doing this. One is to use the delicate galvanometer as a "direct reader," that is, to let the electromotive force of the thermoelement furnish the power and produce the current measured. If the resistance is constant the reading will, after a suitable calibration, give the electromotive force of the thermoelement which, by means of a table or of a suitable scale in the galvanometer itself, will FIG. 1.-SIMPLIFIED POTENTIOMETER. POTENTIAL DROP ACROSS THE PART PIN or CIRCUIT OF BULL CELL BALANCES THAT OF THERMOELEMENT TC WHEN GALVANOMETER G READS ZERO. give the temperature. The other method, that of the potentiometer, is to balance the electromotive force of the thermoelement by means of another electromotive force, using the galvanometer to tell when the balance is made. The usual way of getting this other electromotive force is to have a battery, the "bull" cell, send a current through a series of resistances, which 'may in a special case be the resistance of a single wire. The fall of potential along this circuit will then, by Ohm's Law, be proportional to the resistance; the potential difference between any two points, proportional to the resistance between the two points. This is represented in Fig. 1, where M and N are the two points in the circuit AZ of the battery. If M or N, or both, is movable so that the resistance

Jan 9, 1919

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941

By T. W. Peterson, J. W. White, E. E. Krist

In developing a minicomputer application for an industrial grinding circuit, the control program is usually coded and the compilation is debugged on a remote access computing system. Final debugging must wait for installation of the minicomputer. This work reports on an alternative. Here both compilation and execution bugs are eliminated before the hardware is installed by testing the control program against a dynamic simulation. Attention is directed toward development of a particular real-time control program for an industrial wet grinding circuit in a copper concentrator. Specific data were supplied by the Anamax Mining Co. for a grinding division consisting of a rod mill followed by two ball mills in parallel. This information was used to set up a plausible model structure.

Jan 1, 1977

By K. R. Weller

The Ardlethan Tin Ltd. concentrator typically recovers 55% of the tin in a gravity concentrate at 51% grade from fresh ore assaying 0.5% Sn. Coarse gravity concentration is performed in a complex circuit involving Reichert cones, spirals, shaking tables and two regrind mills. The paper describes how flow and size-by-size sample data from a steady-state survey were used to construct a computer model of the plant involving 46 process streams. The data reduction involved a computer- aided mass balancing technique, recovery-size modelling of gravity concentrators and the use of a mineral dressing flowsheet simulator. The model was used to simulate possible rearrangements of the available equipment. Early simulations indicated that improved performance could be obtained by using spirals to-treat cone middlings or tailings rather than cone concentrates. A test spiral rig was used at Ardlethan to determine typical performances for all cone product streams and the results were incorporated in new simulations. A revised circuit was recommended and implemented by Ardlethan Tin as far as physical restraints within the plant would allow. Production figures show that a substantial increase in tin recovery and 10-15% increase in milling rate were achieved following the circuit changes, and these improvements were sustained over a six month period.

Jan 1, 1984

By William C. Aitkenhead, John A. Jaekel

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U808. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U308 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pct U308 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8, with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct.

Jan 1, 1959

By John B. Miles

The present period of depression in the iron industry, with the resultant close approximation of the cost of production to the selling-price of pig-iron, should make the discussion of this subject at this time not only interesting but profitable. It is possible that it may result in the collection of data, which when added to those set forth in this paper will clearly indicate the influence of the rate of driving a blast-furnace upon its fuel-economy. The question is not whether an excessive rate of driving (meaning a rate definitely in excess of the average rate in the United States) results in an increase in the fuel-consumption, but rather whether a rate considerably less than the average does not result in a marked decrease in the fuel-consumption. The commercial and metallurgical sides of this problem must be kept separate. With a large margin between the cost of production and the selling-price of pig-iron, and a plant already in operation, it is frequently profitable to sacrifice a couple of hundred pounds of fuel per ton of pig-iron in order to secure the greater gross profits resulting from a larger tonnage. When this margin decreases with a plant in operation, or when the determination of the size of a new furnace intended for a certain production confronts the management, a clear understanding of the effect of the rate of driving upon fuel-economy becomes necessary. If it be granted that slow driving leads to low fuel-consumption, it should be borne in mind in the design of a new plant for the production of a certain tonnage that the adoption of an economical rate of driving increases only the size of the furnace proper, whereas, due to the decrease in quantity of blast required on account of the decrease in fuel burned, the stoves, the blowing-engines, the boilers and the piping may be de-

Jan 1, 1909

By Frank A. Crossley

The work described has one serious shortcoming: grain size was not monitored during heat up to the temperature (1675°F) of isothermal anneal. The chief obstacles to p grain growth in titanium a-ß structures are the a grains. Heating a structure such as that shown in Fig. 1 to a temperature close to ß transus causes dissolution of a grains in order to adjust the a/ß ratio, compare Figs. 1 and 2. During this process there is a concomitant growth of the ß grains—otherwise ß grains would have to be nucleated in order to adjust the a/ß ratio. When the annealing temperature is reached the a/ß ratio stabilizes and this initial phase of ß grain growth ceases. After an incubation period growth resumes as described. Some 0 grain boundaries can be clearly seen in Fig. 1. (Skilled metallography commonly produces photomicrographs which show more structural detail than direct observation.) These boundaries suggest that the average ß grain size is approximately 0.002

Jan 1, 1970

By Augustus Locke, Edward H. Perry

In the exploration of a copper deposit by drilling, obvious advantages are to be gained from a distinction between primary and secondary ore.' Perhaps the chief of these is the aid which such a distinction renders in determining where a given hole should stop. The copper assay, often a sufficient guide, cannot always be exclusively relied upon. Primary ores may extend downward indefinitely and may fluctuate in value independently of depth: if primary ores are consistently lean for a considerable vertical distance, there is little reason to expect that, still deeper, they will increase to the commercial grade; on the other hand, rich primary ores may persist uninterruptedly downward or may come in again below a lean interval. Secondary ores, however, have a comparatively limited vertical extent; in a large way enrichment decreases with depth and finally gives out. It follows then, that when a hole descends from profitable ore into ore of less than the commercial minimum, the practical significance of the situation depends upon whether this decrease results from a decrease in secondary enrichment or is a variation in primary content: if the copper of the ore passed through has been chiefly secondary, little is gained in the average case by extending the hole much below the point at which the commercial limit is reached; but, when copper is chiefly primary, due weight must be given to the possibility that, still deeper, the ore may again improve. The distinction between primary and secondary ore may of course be effected through an examination of the drillings. It has been found, however, to be facilitated by curves made by plotting assays against

Jan 1, 1916

By N. Brown

IT has been observed that a hexagonal-close-packed crystal will undergo the same macroscopic displacements as an isotropic material if the basal plane is perpendicular to the axis of twist.&apos; Other orientations may produce both bending and twisting, but this analysis will be confined to pure torsion of a right circular cylinder. The z axis, the axis of twist, and the specimen axis are coincident. The displacements are given by Uq = rz, Ur = Uz = 0 [1] where 4 is the angle of twist per unit length. This requires rotational slip, as discussed by Frank&apos; and Wilman, which may be observed readily. The relative rotation of adjoining slip planes is simply produced by a movement of a planar grid of screw dislocations."." The screw dislocations are of the same sign and they move radially inward. For hexagonal-close-packed metals, the grid is hexagonal and the screw dislocations lie in the < 2110 > directions. The displacement of a point is the resultant of two displacements produced by intersecting screws sweeping over the point. The dislocations must pass over the point (r, o) in such a manner that its resultant displacement corresponds to the observed macroscopic displacement. If 6&apos; is measured from the [1010] direction, then for 0 < ? < ~/3, only the [1210] and 121101 type screw dislocations are needed to produce the required displacement. If n1 screws of type [1210] and n2 of type [2110] pass over a point, then, in order that Ur = 0 n, sin ? - n2 sin (/3 — 6&apos;) = 0. [2] If the tangential displacement is to be independent of 0, then n1 cos ? + n2cos (/3 —?) = N [3] where N is independent of ? and thus depends only on r. Nb is the tangential displacement where b is the Burgers vector. Since U? is a linear function of r, then N must be a linear function of r. If a2 is the outer radius and a, is the inner radius to which the plastic deformation has extended, then N = Nm2 r-a1 [4] This function meets the conditions that at

Jan 1, 1956

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry&apos;s use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel &apos;economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By Sylvain J. Pirson

The question of the interpretation of apparent resistivity curves is still a much disputed subject although the discussion has been going on for several years, mainly since Gish and Rooneyl made their first measurements on the Tidal Basin at Washington, D. C. As a first approximation, they interpreted the depth to a horizontal discontinuity in terms of the electrode spacing at which a maximum or a minimum occurs in the resistivity curve. Later on, Lancaster-Jones2 proposed a closer approximation of depth determination by evaluating the depth to a horizontal discontinuity as the two-thirds of the electrode spacing at which a point of inflection occurs in the resistivity curve. An accurate determination of the depth was recently proposed by Tagg3 for a two-layer problem. It is a graphic solution of the problem by means of charts calculated from the formula of the apparent resistivity based on the theory of electrical images. Tagg&apos;s method is theoretically sound but the fact that the layers have been assumed to be homogeneous and isotropic must not be overlooked. Abusive use of the method has been made by geologists who have failed to recognize the fact that nature offers only few cases where the conductivity of the rocks may be assumed to be the same parallel and perpendicular to the bedding plane. Actually the ratio of the two resistivities in those directions may take values ranging from one (isotropic medium) to three for shales. In such conditions Tagg&apos;s method leads to disappointments. A method recently advocated by Manhart4 and Tattam6 forces Tagg&apos;s method to give a solution where manifestly the case under

Jan 1, 1934

By R. A. Kinzie

THE major operating costs in a cement plant are labor, power, and fuel. The opportunities and methods of savings in labor and power parallel other industries. Because our industry&apos;s use of fuel is large and its method of use is unique, the devices adapted for saving fuel are of interest. In normal practice the raw material in the form of a dry powder or a mud is fed to a rotating inclined cylinder where it is dried, calcined, and clinkered. In a Lepol kiln the raw material is rolled up into little balls with water in the nodulizer, fed to a traveling grate on which it is dried and partially calcined and tben to a short kiln where the process is finished. The more usual methods of saving heat have been the use of long kilns with chains in wet process plants and the use of waste heat boilers in dry plants (fig. 1). At the Santa Cruz plant we have used a Lepol system kiln and achieved a fuel &apos;economy of 4.7 gal per bbl of clinker or about 704,-000 Btu per bbl. This can be compared with our old kilns using the same fuel and raw material which consume 7.8 gal per bbl or 1,130,000 Btu per bbl. These are gross Btu and not the net figures usually used in reports of foreign companies. Our average consumption for 1948 was 708,000 Btu per bbl of Lepol clinker, based on cement sold, and oil purchased. The overall fuel consumption for 1948 was 6.61 gal per bbl. The Lepol system consists of a nodulizer, a grate, and a kiln. There is the usual accessory equipment which is similar to that used in other cement plants. The following description covers the equipment in operation at our plant. The nodulizer is a cylinder 8 ft 10 in. in diam by 18 ft long set on a slope of 1/2 in. per ft, and rotated at about 10 rpm. It is driven by a 50 hp wound rotor motor drawing about 9 kw. The inside of the shell is cleaned by a continuously operating scraper which draws 0.1 kw. The dry raw material is fed to the nodulizer where, being sprayed with water, it rolls into small spheres about 90 pct being between 1/2 and 1 in. in diam and containing about 15 pct water. The nodules fall on the traveling grate where the hot gas from the kiln is pulled down through the

Jan 1, 1951

By Nobuhiro Takahashi

PROLOGUE The Yaguki mine, which is located near the southern end of the Tohoku region, Japan, near the coast of the Pacific Ocean, had had a long history as a copper mine, but had not been operated since 1925. About 30 years later it was reopened by Nittetsu Mining Company, and in 1958 a small flotation and magnetic separation plant, a so-called test plant, started production. The ball mill the author first met, a 8x4x4x7 ft tricone mill, called No.1 mill, had started running at that time. With his experience in initial, running of this mill he realized that the ball mill was not simply a preparatory process to flotation, but a determinant factor for flotation performance, an energy-consuming and costly process, and that its operation control was an important task in the plant (1). The working part of an operating ball mill is the ball load inside, whose properties govern the grinding performance. Its size distribution affects the efficiency greatly and the capacity is nearly proportional to its weight. When a ball mill operates for a long period of time with a constant and consistent addition of renewal balls, wear and renewal of balls are balanced, and an equilibrium ball load is formed. A stable equilibrium load is the primary requirement for a stable ball mill operation. However, renewal ball size would be the most influential factor affecting efficiency and capacity of operating ball mills. To improve efficiency, to increase capacity, or to get finer product, attempts to find out the optimum size assortment of renewal balls should be made. When re-

Jan 1, 1976

By F. E. Steigert, A. H. Geisler

THE permanent magnet alloy comol, which contains 17 pct Mo, 12 pct Co, balance Fe, exhibits a precipitation reaction analogous to that at the iron end of the binary Fe-Mo system. The equilibrium precipitate, (P,), has a structure isomorphous with Fe,Mo, which is rhombohedra1 with parameters a = 8.97A and a = 3038.6&apos; according to the work of Arnfelt and Westgren.&apos; In the ternary alloy the parameters are a = 8.87A and a = 31°0.5&apos;. Oscillating crystal patterns of a single matrix crystal, M, in which P, was precipitated by slow cooling from 1300°C, showed that the orientation relationship of the two lattices is as follows: (110)P3 // (110)* (111)p3 // (110)m There are crystallites of P, in 12 different orientations in a single crystal of the parent solid solution. Microscopic examination shows that the crystallites are generally plate-like with their lateral dimensions parallel to (110) matrix planes. When precipitation in a supersaturated alloy quenched from 1300°C progressed isothermally at temperatures between 600" to 800°C, the evolution of the P, structure could be traced. Diffuse diffraction effects in Laue patterns provided early evidence of the precipitation process. Analyses of these by a previously described technique2 showed that they corresponded to rod-like elements parallel to <110> matrix directions in reciprocal space. With further aging to promote growth of the precipitate, the rod-like elements contracted to points in reciprocal space for normal Bragg reflection from the precipitate as shown by the left diagram in Fig. 1. Thus the diffuse scattering was attributed to the small thickness of the plate-like particles which was inadequate for sharp diffraction. When the precipitate particles were first thick enough to give normal diffraction their structure was different from that of the equilibrium precipitate, P,. The first structure, P1, presumably is a coherent transition struc-

Jan 1, 1952

By F. G. Coggin

" If you could only get that motion into a machine," said a gentleman, as he watched the process of making a " van " on a shovel, and saw the copper roll up to the highest point, "it would beat the world for slime-dressing." This idea has led to many an effort to get into a machine that peculiar motion, called the " vanning motion;" and so cams, eccentrics, eccentric gears, levers, bell-cranks, togglejoints, links, springs, etc., have been brought into requisition, while a contribution has been laid upon all the conceivable motions, rolling, tumbling, swinging, jerking, tossing, dropping, tripping, intermittent, regular and irregular, or a combination of some of them, to which have been added percussion, concussion, and more discussion —all in a vain attempt to combine in a single machine the consecutive motions of the shovel, in washing, flowing, and tossing the van. The Patent Office Reports, and the various mills of the country, show, as a result of this, a lot of gimeracks, most of which never went beyond a first trial, finding their way to the scrap-heap. Others still running might as well be there; while some have considerable merit for dressing other and richer sands than copper. It does look tempting to see that clean edge of copper climbing up the shovel-blade; but those who have seen in it such visions of large fortunes have not considered the time it takes to make a van, compared with the small quantity treated upon the shovel; and this points to the reason for the failure of all that class of machines called " vanning machines," when used for dressing copper slimes, namely, a lack of capacity. The writer has come to this conclusion through an experience with the Rittinger side percussion-table of the most improved make, sent from Germany to the Calumet and Hecla Mining Company, and with the Ellenbecker tables, used by the same company, both of which are good types of that class of machines. In both of these machines, the tables are suspendetl by rods which allow them to swing, and they can also be adjusted for the purpose of varying the inclination of the table. In the Rittinger machine, the motion of the table is at a right angle to the flow of the slime, being produced by a wiper-cam which throws the table against a spring, which throws it quickly back against a stop, the percussion throwing up the mineral. In the Ellenbecker table, the motion is

Jan 1, 1884

U.S. Steel Uncovers Massive Iron Ore Deposits in Nevada United States Steel Corporation has confirmed that mineral investigation in Lyon County, Nevada. has been under way since 1960. Confirmation followed press reports of a statement attributed to a Nevada State inspector of mines to the effect that the Corporation has found a major iron ore deposit that may also contain copper ill West Central Nevada. Drillings over the years in a number of locations have indicated extensive iron ore bodie containing a possible quarter of a billion tons of ore of a basically magnetite composition. analyzing less than 40% iron, which would require beneficiation for commercial use. Some of these deposits are deep- lying while others would permit open pit mining. These bodies contain copper in quantities of approxiimately 0.3%. More recent drilling in another area has disclosed evidence of additional deeply-lying deposits of a lower fe content but with more promising indications of copper. A realistic estimate of fe and cu ore reserves cannot be made until more drilling is completed.

Jan 1, 1970

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

By M. P. Dalton

THE problem at the Morning mill is to separate the galena, which contains a great percentage of the silver, from the sphalerite, making each into a commercial product. The ore as received from the nine is dumped into hopper-bottomed bins of 1200 tons capacity. These are divided into five sections, the first section being the regularly used section and the re-mainder used as a reserve bin. The ore is first passed through a 9 by 15-in. Blake jaw-crusher with an opening of 4 in. This allows a ham-mer head to pass through without damage. The crusher discharges to a conveyor that delivers the ore into a two-section punched-plate trommel screen with 1 ½ and 2-in. openings. The undersize is carried by means of conveyors to the mill bins. The oversize passes over a shaking feeder and through a spray or high-pressure water to a picking-belt, where waste and crude ore is hand-sorted. About 4 per cent of the ore by weight is picked out as waste, assaying about 0.6 per cent lead, and this is discarded over the dump. About 4 per cent of the ore by weight is removed as crude ore, assaying 10 oz. silver, 30 per cent lead, and S per cent zinc, and is shipped direct to the smelter. The remainder of the oversize from the picking-belt is con-veyed to a 4-ft. Symons cone crusher with 1-in. opening, which is interesting as a new introduction in this dis-trict. The machine consumes approximately 40 hp. and the pinion shaft travels 555 r.p.m. The horsepower is rather high, but the machine has an extraordinarily large capacity, and, due to the unique construction, there is no danger of tramp steel causing any damage, as in that case the discharge "opening" is automatically

Jan 7, 1927

By Joseph Pogue

IT IS well known that one of the cornerstones of economic theory is the so-called law of supply and demand, which, really, is a group of economic laws, one of which may be succinctly stated : A rise in price tends, sooner or later, to increase supply. It is the fear that, in the case of petroleum, a limited natural resource, a point will soon be reached when supply will not respond adequately to price advances, which in recent years has prompted a movement for oil conservation. This movement has lately taken concrete shape in the appointment of a Federal Oil Conservation Board by the President. An important aspect of the law of supply and demand is that the supply of any commodity is not an entity per se, but is a factor of price. Supply, without the specification of price, has no exact meaning; and in practice supply cannot be divorced from considerations of price. Mathematically, supply may be expressed by the formula SP, which means that supply varies with price, just as the value of 10 raised to the x power varies with x. In its technical usage, supply is the quantity of a commodity that is bought currently on the market at a given price. In the case of a natural resource, however, this quantity will eventually depend not alone on price but on the physical volume of the reserve that exists and. that, in consequence, can respond to the stimulus of price. If this reserve is fixed in size, we must sooner or later reach a point where supply can no longer respond to price in the usual degree and a permanent shortage. will develop which no advance in price can correct, except in so far as higher prices may curtail demand or improve the efficiency of utilization.

Jan 3, 1925

By L. P. (Les) Haldane

Building a small underground coal mine is a risky endeavor, especially in the recent economic environment. ARCO&apos;s Mt. Gunnison No. 1 Mine, located in western Colorado, was designed and built as a small expandable speculation mine with initial production to be sold on the spot market, so it was very important to minimize capital exposure. This mine, operated by West Elk Coal Company, a subsidiary of Anaconda Minerals, was successfully built under budget at $35 million, and has been operating successfully since completion of construction in late 1982. The initial planning phase of a project is extremely important for testing the economic and technical feasibility of a proposal. The construction phase, by contrast, carries with it significant cost and quality risks which can relate to long-term economic and operating problems and therefore directly affect the viability of the project. This paper discusses several different aspects of the cost overrun risk involved in building an underground coal mine, and how attempts were made to minimize these risks during construction of the Mt. Gunnison Mine. Good people, construction planning, and execution are essential factors in assuring a quality, cost-effective project, with corresponding risk minimization during the construction phase and long term favorable implications for the operating phase.

Jan 1, 1985