Search Documents

By John Cogan, P. M. Gomez

A typical problem in applied rock mechanics is an accurate prediction of support requirements for deep rock cuts. This paper presents experience with this problem as obtained from excavations for a powerhouse at the Pine Flat Dam near Fresno, California. The project, sponsored by the Kings River Conservation District is still under construction. Highly jointed and weathered rock was discovered during initial excavation. Wedge failures along clay filled joints and bedding planes presented potential support problems. Detailed mapping of joints and beds was undertaken to establish basic patterns of all rock discontinuities including mean orientations and an estimate of orientation variations. Rock bolting patterns were devised to meet these patterns as excavation proceeded. Shear friction angles across joints and beds were estimated from rock wedge fallouts. Friction angles as low as 27º were identified on highly weathered joints. Weathering strongly influenced stability conditions. Examples of bolting patterns to stabilize critical slopes are presented.

Jan 1, 1982

By C. W. Kempton

If New England were located in some distant and almost inaccessible region, there is no doubt that its mineral resources would have been ere this well developed and generally acknowledged, but laboring under the disadvantage of nearness, it has been neglected. Its surface, moreover, is not cut up by mountains and canons, and the remnants of many of the old ridges are extensively covered by glacial drift. Having for the past ten months been engaged in the development of a mineral district in Southeastern Maine, 1 would take this opportunity to lay before the Institute sketches of results, and try to give some idea of the formations as found. The Sullivan Mining District extends from the town of Franklin, through Hancock, Sullivan, and Gouldsborough, from northwest to southeast, about sixteen miles. A general idea of this locality may be gathered from the map accompanying. (Fig. 1). Sullivan is situated at the head of Frenchman's Bay, ten miles north from Bar Harbor, Mount Desert, twelve miles from Ellsworth,

Jan 1, 1879

NEW MEMBERS The following list comprises the names of those persons who became members during the period July 10 to Aug. 10, 1915: Members ALBERTSON, MAURICE MERTON, Mine Surveyor, Mining Corporation of Canada, Cobalt, Ont., Canada. ARMSTRONG, GEORGE CHANDLER Mgr., Indian Refining Co., Lawrenceville, Ill. BARBER, MAX HAYDEN, Min. Engr Supt., Crosby Mine, Nashwauk, Minn. BARNESON, JOHN Merchant, 310 Sansome St., San Francisco, Cal. BENSEL, JOHN A., Cons. Engr 111 Broadway, New York, N. Y . BORGESON, ANSHELM CYRUS, fin. Engr Shenango Mule, Chisholm, Minn. BROOKS, CHARLES PETER, Min. Engr 228 Dooly Bldg., Salt, Lake City, Utah. BROWN, FRANK HAROLD, U'011',. Min. Engr., Federal Co., Inc., 50 Broad St., New York, N. Y. CLARK, DOUGLAS Kellogg, Idaho.

Jan 9, 1915

By John V. Beall

They came from Paris, Washington and Rabat; two directors, two chief geologists and the president of our own local subsidiary company. Such a meeting was not unprecedented, but it seeemed to us that our president was overzealous in arranging for inspections of each exploration site. One was a problem. Jacques, our president, had concocted the idea that we should lead this learned, mature (not exactly aged) group into the desert to see newly found anomaly. It was in virgin country and had been marked by dropping a flour sack on it from the air.

Jan 1, 1971

By J. R. Slotemaker

As successfully pilot-tested at a quarry producing limestone for a large cement plant, swiftly flowing streams of rock enter the Gromax Selector. They are electronically scanned while in motion and light reflection data flashed to logic circuits. The logic circuits compute the total light deviations in each rock as it passes the scanner. Thus, a rock with striated or spotted impurities can be rejected or accepted on the basis of its proportional content. The actual case history of this equipment's development at a limestone quarry in the Southeast serves to illustrate its general area of usefulness.

Jan 1, 1964

Uranium, the object of a quarter billion-dollar search in the US during 1977, is a ubiquitous element rarely found in economic concentrations. It originates in magmas as a large tetravalent ion, the size of which restricts it from the crystal lattices of many rockforming minerals. Instead, according to United States Mineral Resources (US Geological Survey Professional Paper 820) as the magma crystallizes, a portion of the uranium is deposited as an intergranular film on rock forming minerals, enters accessory minerals, or forms its own minerals. The remaining uranium becomes concentrated in magmatic differentiates, where it forms minerals in pegmatites and veins.

Jan 10, 1978

By Ralph Hultgren

A CONSIDERABLE interest in the subject of superlattices has been mani-fested by many papers and reviews that have recently appeared, both in physical and metallurgical publications. This interest is due largely to the apparent simplicity of the ordering process, which permits the explana-tion of many phenomena on the basis of elementary theory. Moreover, ordering may cause important changes in the physical properties of alloys. In this paper, we shall discuss the causes of superlattices in terms of simple properties of the elements that give rise to them, together with a series of experiments performed to test our conclusions. Evidence is presented that in some cases the process of ordering is more complex than might be supposed. While the different species of atoms are usually found in random posi-tions in alloy lattices, in some cases unlike atoms tend to be nearest neighbors. Bethe'st "order of neighbors" is a statistical measure of this tendency. At suitable compositions it is possible for atoms in large regions to be regularly arranged, which causes superlattice lines to appear in X-ray diffraction patterns. Bragg and Williams2 have dealt with this "long-distance order" in their fundamental work on superlattices. Excellent discussions of superlattices are to be found in current reviews.3,4

Jan 1, 1939

By Jorge Munoz Reyes

There are three main oil areas in Bolivia (Fig. 1) although so far only one has yielded petroleum in commercial quantities. The Sub-Andean zone is along the easternmost ranges of the Andes, bordering the large eastern and northeastern lowlands. It extends from the Peruvian frontier, north of Lake Titicaca in a southeasterly direction towards the city of Santa Cruz and from there southward to the Argentine border. This zone forms a belt about 1200 km. long by 100 km. wide, and comprises a series of parallel, very rugged, low ranges. Oil has been known and utilized by the natives in these regions since colonial times, from the large number of seepages, which in modern times have led to the discovery of many fields. The second oil zone of Bolivia lies along the eastern and southern borders of Lake Titicaca, on the Andean high plateau, at an average altitude of 13,000 ft. above sea level. It comprises an area of approximately one million hectares (2,470,000 acres). Several seepages are known here, but little development has taken place, because of the difficulties encountered, as the greater part of the territory is covered by volcanic tuffs and ashes, which conceal the structure underneath. The third area is called the "Central zone," and is in the heart of the country, in the Department of Cochabamba, covering approximately five million hectares (12,350,000 acres). This area consists mainly of broad valleys flanked by low rolling ranges. Natural seepages are not known to exist, but there are secondary evidences of the presence of oil. The outcropping rocks are mainly Paleozoic (Silurian and Devonian sandstones and shales). Albertite and other forms of polymerized petroleum have been found in this region. Of these three main oil areas, only the first one is at present productive on a small commercial scale. This zone, developed almost exclusively by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey, is divided from south to north into the following local fields: 1. Bermejo (On the Argentine border) 3. Sanandita 5. Camatindi 2. San Telmo 4. Caigua 6. Machareti

Jan 1, 1935

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By J. H. Frye, C. P. Sun

A Frimary substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced, solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver alloys.1-5 It has been shown that at least four factors are involved: (1) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2,4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work-hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. Calculation of Rates as Work- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

St. Joe Minerals Corp. opened a new $30 million mine and mill at its Balmat-Edwards division in September. It will be the largest single zinc mining operation in the United States. St. Joe expects to produce more than 200,000 tons of zinc concentrates from its combined Balmat-Edwards mines and mills in 1972, equivalent to more than 100,000 tons of zinc metal-20% of U.S. mine production. The company has operated in Northern New York since 1926, having commenced zinc mining with its Edwards mine and mill, 12 miles from Balmat. They will continue to operate at a rate of 31,000 tons of concentrate per year. St. Joe started the Balmat facility in 1930 with two mine shafts and a mill, with a capacity of 2300 tpd.

Jan 1, 1971

By Frederick Laist

The ores received at the Washoe Smelter come almost entirely from the mines in Butte and contain the following minerals : Chalcocite, Cu2S; covellite, CuS; chalcopyrite, CuFeS2, (trace); bornite, Cu3FeS3; enargite, Cu3AsS4; malachite, Cu2CO4 + H2O (trace); pyrite, FeS2; sphalerite, ZnS; rhodo-chrosite, MnCO3, (less than 1 per cent.); rhodonite, MnSiO3, (less than I per cent.). The country-rock of Butte is of the granite family and is a quartz-monzonite containing a little less silica than typical granite. It is made up of the following rock-minerals in approximately the proportions indicated: Minerals. Composition. Per Cent. Quartz SiO2 20 Andesine 1/2 NaAlSi3O8; 4 CaAI2Si2O8 42 Orthoclase KA1Si308 23 Hornblende 1/2 Ca(MgFe)3Si4O12; & (MgFe)2(AlFe)4Si2O12 6 Biotite (HK)2(MgFe)2A12Si3O12 9 Titanite CaTiSiO5 0.1 Apatite (CaF)Ca4(PO4)3 0.05 Magnetite (FeO)(Fe2O3 0.15 Pyrite FeS2 0.02 99.32 The main country-rock (quartz-monzonite) is cut by dikes of aplite, a granite having the following composition: Quartz, 30; andesine, 20; orthoclase, 45; ferro-rnagnesian minerals, 3; pyrite, 0.1; total, 98.1 per cent. Closely associated with the copper-deposits are dikes and bodies of " Modoe" porphyry, technically known as quartz-

Jan 1, 1913

By John W. Pack

AT present the manufacture of metallic zinc, or spelter, in Missouri, is carried on only at the establishments located at Carondelet, or South St. Louis. Although the development of the industry has not yet reached that fulness which it has attained elsewhere in the United States, still the commanding advantages of position of these establishments are so evident that the prospective importance and magnitude of spelter manufacture in this State, and especially at this locality, can hardly be doubted. A study of the chemical and technical aspects of the business of these points cannot be without interest to the metallurgist as well as to the capitalist. I have endeavored to investigate, as far as was practicable, within the limits of a paper of this character, some of the problems connected with this industry, at the same time making a few comparisons of the results attained at some of the Carondelet works with those of other establishments with regard to which information could be obtained. In the prosecution of these studies I have been kindly aided by the managers of Carondelet establishments, and by Prof. Charles P. Williams, Director of Rolla School of Mines. To the latter I am especially indebted for assistance in regard to methods of analysis. To all these gentlemen I return my thanks for their valuable aid. Other sources of information will be duly credited in their proper places.

Jan 1, 1875

By Arthur V. Abbott

During the past four years I have had occasion to make quite extensive use of steel castings in the manufacture of testing-machines and large scales for Messrs. Fairbanks & Co. The failure of some of these' castings at stresses much below those which were claimed for them by the makers, induced me to institute a series of experiments to determine the actual constructive value of the steel castings now to be obtained in this country. The art of steel-casting is rapidly improving, almost every issue of the scientific press bringing accounts of some new development; consequently, the results of the following experiments are only exponents of the value of steel castings as at present made. In order to make the examination as thorough as possible, ten sets of patterns were made and forwarded to as many different firms in the country who advertised to make steel castings. The first part of the accompanying table gives a list of these manufactures, together with the price per pound. The order accompanying the patterns simply requested the manufacturer to supply two castings from each pattern of his ordinary product of steel. These castings were sent to me and paid for in the usual manner, so that it is probable that the samples fairly represent the quality of the average of steel castings, and are free from the suspicion of being "special runs." Two patterns were sent to each maker, one being a straight

Jan 1, 1886

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By S. R. B. Cooke, Iwao Iwasaki, Hyung Sup Choi

John Dasher (Materials and Processes Engineer, Crucible Steel Co. of America, Pittsburgh, Pa.) The authors are to be congratulated for their excellent work, dramatic results, and persuasive explanation on the neglected subject of the temperature variable in soap flotation. The explanation includes why heat is helpful in conditioning and why heat is helpful in flotation. This is a fine start, but I hope the work will be continued to show which is the major effect. In the work of Noman and Dash er(1) it was found that substantially all the benefit of heat came from the conditioning step, and that results were much better if a thick pulp was conditioned hot and then diluted with unheated (or less heated) water for flotation (or agglomerate tabling) than if the same quantity of heat was used to condition and float at some intermediate temperature. In other words, heat for conditioning gives a Rood return, but additional heat for dilution water is near or beyond the point of diminishing return. Strathmore R. B. Cooke, lwao lawsaki, and Hyung Su0p Choi (Authors' Reply) Mr. Dasher'skind comments on our paper are appreciated. In view of the relative simplicity of empirical investigationsof the temperature variable upon conditioning and flotation, it ispuzzling why the subject is so neglected. Our work, being sub sidiary to the main investigation of the effect of structure of fatty acid collectorsupon iron ore flotation, was quite restricted, but we intend to return to the subject as soon as possible. Mr. Dasher's point, that given a certain number of calories it is better to invest them for conditioning in a thick pulp rather than to spread them out for both conditioning and flotation operations, is well taken and cannot be argued. On the other hand there is no question that high temperature during the flotation of iron ores induces superior frothing characteristics, and, in particular, greatly augments the rate of flotation and markedly decreases the time required for "difficult" particles to float.

Jan 1, 1961

By Oscar Kuchs

IN January and February of the current year, at the Tooele plant of the International Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast- furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of reverberatory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it was planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary: to install a bag house, a fan, and the necessary flues to complete the equipment.

Jan 7, 1914

By C. A. Pierce

Studies of roof and floor movement are of interest to those actively engaged in mining. This is especially true in the case of an entirely new area where there is no precedent for guidance. The potash deposit being mined is in the southeast corner of New Mexico, about 20 miles east of Carlsbad. The deposit was formed by the land-locked, shallow, Permian Sea that extended through parts of western Texas, Oklahoma, Kansas, southeastern Colorado, and eastern New Mexico. The saline deposits vary from 500 to 4000 ft. thick. Neither of the companies operating in this area has delimited its commercial ore bodies. As all production so far has been from Federal and State leases, the Department of the Interior and the State of New Mexico have a direct interest in the development and extraction of these ore horizons. The ore is composed of an intimate mechanical mixture of sylvite (potassium chloride) and halite (sodium chloride). It lies generally in a horizontal bed varying from 5 to 12 ft, in thickness, and has a cover of approximately 1000 ft., consisting of about 500 ft. of salt beds and 500 ft. of sediments. The immediate mine roof for several feet is principally salt with some potash and clayey material. The next 500 ft. above, from the standpoint of structure, may be considered rock salt with a few inter-bedded potash members. The upper 500 ft. is of sedimentary (Permian and Triassic) origin and contains several water-bearing formations with flows varying from 10 to 500 gal. per minute. This water intensifies the interest in convergence problems as the ore and surrounding formations are water soluble. Potash salt (sylvite) and rock salt (halite) are plastic minerals. Plasticity is defined as a "property of solids by virtue of which they hold their shape permanently under the action of small shearing stresses but are readily deformed, worked, or molded under larger stresse."1

Jan 1, 1942

By M. Friedman

Applications of rock mechanics to the design of engineering structures in rock involve the assumption that the stresses are due entirely to the present applied loads. For instance, it is assumed that the vertical normal stress in undisturbed rock free of topographic effects is equal to the weight per unit area of the overburden. In fact, vertical dilatational strains associated with stresses of more than 100 times the present overburden pressure have been measured by strain-relief methods on outcrops. 1,2 The notion of residual strain (stress) or latent stress3 seems unassailable; and indeed this has long been recognized by metallurgists. It is difficult, however, to assess the residual component of the in-situ state of elastic strain with conventional strain relief methods employed in mines or down boreholes. That is, in principle, the in-situ state results from the superposition of present applied loads (natural or man- induced) and potentially recoverable elastic strains (stresses) that exist in a given volume of material even though there are no external forces across the boundaries of the body (Voight,4 and Fig, 1). Accordingly, only in unloaded blocks can the true residual strains be measured by strain relief methods. Using X-rays, the elastic strains locked within the quartz grains or crystals of a rock can be measured. These strains are known to persist even when the rock is reduced to small chips but to vanish when the rock is disaggregated and the grains are powdered. Although we have just begun to investigate the mechanisms by which the strains are stored (see Preliminary Results), we believe that "pressure solution'' at grain boundaries, secondary cementation under load, permanent ("plastic") deformation, and temperature changes are possible processes. In any event, in our study of naturally deformed rocks, it is significant that we are work-

Jan 1, 1972