Search Documents

By AIME AIME

AMERICAN INSTITUTE OF MINING ENGINEERS. Vii MEMBERS' PRIVATE RECEPTION ROOM. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the use of members of the Institute who desire temporary private office accommodations. In order that the benefit of this arrangement shall not be restricted to a few members only, the length of time of continued occupancy is limited, and applications will be considered in the order of their receipt. A small fee will be required for the use of this room.

Jan 9, 1907

By K. C. Strebig, C. W. Schultz, A. A. Selim

For some time researchers have attempted to in- crease drilling efficiency (and therefore reduce costs) by adding certain chemical agents to the circulating medium. The effect of some organic additives on the diamond drilling of quartzite was recently investigated in the laboratory by personnel of the U. S. Bureau of Mines. In these tests, the penetration rate and bit life were found to increase with the use of additives. In addition, an economic analysis of a hypothetical 1000-ft hole showed that additives can reduce drilling costs by 30%. Wetting Agents Improve Drilling Efficiency Much of the interest in the use of wetting agents to improve drilling efficiency is the result of an observation made by Rehbinder, Shreiner, and Zhigach.1 These investigators postulated that drilling creates a region of increased crack formation directly below the bit and that a circulating medium that wets the rock will also penetrate the micro- cracks of the predestruction zone. Increasing the molecular affiinity (wetting ability) of these circulating media for the surface of the rock helps the deformation and destruction by softening the rock in the zone of increased crack formation. In this manner, the hardness or strength of the rock is decreased as the medium wets the rock in the predestruction zone. This is known as the "Rehbinder effect." Rehbinder's work has prompted many investigators to examine the relationship between the use of additives and the mechanical destruction of rock. Engelmann, Terichow and Selim reported that the maximum penetration of the rock by a diamond point in a solution environment was at the isoelectric point of the mineral and solution interface.2 Improvement in rock breakage with the use of additives was observed by Frangiskos and Smith.3 Joris and McLaren suggest that additives having a lower surface tension than water will also be more efficient in cooling the diamonds.4 Additives help remove fine cuttings from the face of the bit and improve efficiency. The latter two authors also report an improvement in impregnated bit life and penetration rates with the use of soluble oil additives. All of these investigations were initiated in the hope of discovering what economic benefits will accrue with the use of additives.

Jan 10, 1969

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By H. C. Fiedler

A high degree of cuhe-on-edge grain orientation and good magnetic properties were obtained in Si-Fe strip processed from laboratory heats containing vanadium nitride inclusions. The higher the nitrogen content the greater was the restraint on normal grain growth and the greater was the ability to undergo secondary recrystal-lization. The degree of restraint in a heat containing magnanese sulfide inclusions was slightly greater than that in the lowest nitrogen vanadium nitride heat. The high rate of diffusion of nitrogen in the temperature range in which the texture is developed makes it necessary to retard the loss of the inclusions until the texture has been developed. MAY and Turnbulll have shown that to develop the cube-on-edge secondary recrystallization texture in Si-Fe it is necessary that inclusions, such as manganese sulfide, be present to prevent normal grain growth. They showed that the driving force for the growth of the secondary grains is inversely proportional to the diameter of the matrix grains, and that the function of the inclusions is to maintain a small matrix grain size. Fast3has developed cube-on- edge texture in Si-Fe by nitriding the hot rolled band. The silicon nitride thereby formed promotes secondary recrystallization during the anneal of the final gage strip. To obtain the best magnetic properties, the inclusions must be removed from the strip after the grain orientation has been developed. Nitride inclusions have an inherent advantage over sulfide inclusions in that the greater diffusivity of nitrogen as comared to sulfur permits the use of shorter times and or lower temperatures for the purification heat treatment. The purpose of the work to be described was to examine the usefulness of vanadium nitride inclusions in developing the cube-on-edge texture and to determine the magnetic properties of oriented strip made from heats containing these inclusions. A comparison is made with a heat having had iden-

Jan 1, 1962

By Elmer R. Kaiser

COMBUSTION of coal and transfer of heat from flames and gases to boiler surfaces continue to be of great interest to engineers here and abroad. Numerous investigations have been in progress to improve furnace and boiler performance and economy. The importance of better understanding of the processes and opportunities for improvement is apparent when it is remembered that heat from at least 500 million tons of coal a year the world over is being transferred to boiler water at efficiencies ranging mostly between 50 and 90 pct. Even slight gains in efficiency, economy, and labor saving become very significant when multiplied by the enormous quantity of fuel consumed. Also the competitive position of the large coal, oil, and gas industries in satisfying the fuel consumers is greatly affected by the achievements made through technical progress with each fuel. This paper is part of a continuing activity of Bituminous Coal Research, Inc., to extend the knowledge of coal utilization for steam generation and to seek promising directions for future research and development in cooperation with others. Particularly in the latter regard, numerous interviews were held during the last three years to seek the experience and advice of boiler and combustion- equipment manufacturers, electric-utility executives, and fuel engineers. A wealth of published information was also reviewed, which together with the interviews pointed to the advisability of further work on ash and sulphur control.

Jan 3, 1954

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By AIME AIME

ONE of the few students to enter the world's first department of ceramic engineering a few years after its establishment at Ohio State University, A. F. Greaves-Walker has since established an international reputation in that field. Before accepting his present position as professor and head of the department of ceramic engineering at the State College unit of the University of North Carolina, Dr. Greaves-Walker spent twenty years in the ceramic and mining industries in Kentucky, Utah, Ohio, Alabama, Ontario, Pennsylvania, and Georgia successively, holding the positions of chief chemist, mining engineer, chief engineer, sales engineer, chief of research, production manager, and finally vice-president. This industrial experience resulted in his building up one of the outstanding departments of its kind in the country.

Jan 1, 1942

By R. R. Hartman, W. B. Agocs

In the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift.

Dec 1, 1956

The plant, animal, and mineral arts and sciences are interrelated, interdependent, equally distinctive subject-matter fields. The artificial, erroneous, and popular idea that minerals occur in great storehouses in nature's treasure room to be removed at will at fabulous profits is about as correct as the assumption that the farmer's life is one of ease in which the crops spring miraculously from the ground. However, both of these fundament-a1 industries, mining and agriculture, have much in common. The extraction of minerals from the ground and the extraction of plants from the soil for immediate use, or conversion to meat, are fundamental activities and subject to many common economic laws. In other words, in many important basic concepts there is little difference between surface and subsurface crops. The farmer owner working the surface of the earth and the owner of a fraction of the oil or coal rights in the subsurface, from which a small yearly income is derived, are interested in the best management of the land for the mutual benefit of all concerned. Therefore, it is essential that in any planning or political action intended to create a new scheme of things, it should be remembered that one plan must fit all sources of primary wealth, whether coal or wheat, petroleum or milk, iron ore or beef.1 And what basic economic difference is there in the processing of a gallon of petroleum and a bushel of corn?

Jan 1, 1950

By H. Xi-Lum

Three rapid cold bonding production methods wing sponge iron powder as a binder for low temperature pellets have been successfully developed. These methods differ from ordinary bonding by the elimination of salt and other catalyzers, equipment corrosion and environmental pollution. Experiments show that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the continuous and stable production of metallic pellets. These methods replace traditional high temperature firing of oxidized pellets for direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved, and production cost may also be decreased because the production of cold bonding pellets does not need additional space.

Jan 1, 1984

By H. C. Otis

During the past year or two considerable time and money have been spent in developing equipment for tubing large-volume high-pressure oil and gas wells without loss of production. That the efforts have met with success is proved by the fact that any properly cased well, regardless of its production or regardless of its rock pressure or working pressure, can now be safely tubed with no appreciable loss of production, provided experienced crews handle the new equipment. It is conceded that a far better gas-oil ratio can be secured by flowing a well through tubing of a proper diameter—the diameter of the tubing depending, of course, upon the volume of fluid and gas and the depth of the well—than by the more usual method of installing a choke at the mouth of the well. Where possible it is becoming the practice to bring wells in through tubing, though in the majority of instances this is not feasible. In many instances it has developed, after a well has been brought in through tubing, that the tubing installed is either too large or too small for the most efficient operation or that the well had not been drilled deep enough. The equipment described in this paper, in the hands of experienced men, permits the tubing of these wells after they have been brought in, with the size of tubing then determined by actual observation to be best suited for each particular well, and with no danger of the well getting out of control, of catching fire, of drilling itself deeper, or of any loss of production. The deeper the flowing production with the consequent future higher lifting costs, the more essential it is that the size of tubing used be such as to give the best possible gas-oil ratio. The ability to bring in these deep wells through the casing and then, immediately after their completion, regardless of volume or pressure, to tube them with the size of tubing that permits the most efficient use of the gas present will doubtless save many dollars. Uses for the New Equipment The equipment permits a further step in the operation of wells where the conservation of gas is of major importance. Perhaps 3-in. tubing

Jan 1, 1930

By Thomas M. Drown

The use of bromine as an oxidizing agent, particularly for sul phur, has become very general in analysis, replacing the stronger oxidizing acids. The object of this paper is to describe briefly the experience which we have gained with this reagent in the laboratory of Lafayette College in the oxidation of metallic sulphides. Most of the simple sulphides, as blende, pyrite, etc., when exposed to the combined action of an alkaline hydrate and bromine, and finally to hydrochloric acid, are completely and promptly dissolved. The procedure is as follows: The very finely pulverized mineral is first treated, in a beaker, with a solution of sodium hydrate of a spe cific gravity of 1.25, and heated ; bromine is then cautiously added to supersaturation, and finally hydrochloric acid to acid reaction. If any of the sulphide is not taken up, the same operation may be re peated. It is necessary, however, that the mineral be very finely pulverized. Instead of using the pure bromine, a saturated solu tion of bromine in potassium bromide may be used with equally good effect. The process is advantageously simplified by making a saturated solution of bromine in the concentrated alkali. This is done by pouring bromine into a solution of sodium hydrate, of the above given specific gravity, until no more is taken up, and then adding a little of the sodium hydrate solution until the liquid does not give off free bromine. The procedure with this solution is as follows: The pulverized mineral is moistened with, say, 10 cc. of the solution, and heated, then hydrochloric acid added to just acid reaction. Two more additions of the alkaline solution, in amounts of 20 cc. each, are added at intervals of about ten minutes, each addition being followed by hydrochloric acid. The total amount of the alkaline solution (containing the bromine) used is, therefore, 50 cc., and the amount of hydrochloric acid should not exceed that necessary to make the solu tion acid after each addition of the alkali. The mixture should be kept hot. After the final addition of acid, the contents of the beaker is taken to dryness and heated in an air-bath to 110° to 115°C., to render silica insoluble. The dry mass is then taken up by hydro' chloric acid and water and, after filtration, the sulphuric acid is pre

Jan 1, 1880

By Arthur H. Redfield

The West Indies are the summits of a submerged mountain chain, the continuation of which must be sought in the mountains of central Honduras. In Haiti, the chain divides, one branch passing through Jamaica and the other through Cuba, the Cayman Islands, and the Misteriosa bank. Suess divides the West Indies into three zones: The first zone is entirely of volcanic origin and includes many recent volcanic cones. It includes the arcuate string of islands, which extends from Saba and St. Kitts to the Grenadines and Grenada. The western half of Guadeloupe belongs to this group. The second zone consists of a geanticline, of which the sedimentary rocks range from the Jurassic to the Quaternary, but consist chiefly of Lower Tertiary sediments. In the west it is broad, including the whole of the Greater Antilles; but in the east it is restricted to a narrow belt, which includes the Virgin Islands (except Anegada), Anguilla, St. Bartholomew, Antigua, the eastern part of Guadeloupe and part of Barbados. The islands that compose the third zone are flat and low. Like the second, this zone is broad in the west and narrow in the east; it includes the Bahamas, Anegada, Sombrero, Barbuda, and part of Barbados. Geologically, Florida and the plain of Yucatan may be regarded as belonging to it. Trinidad and Tobago, though geographically adjacent to the Lesser Antilles, are geologically a detached part of the South American continent. The crystalline complexes of northern Trinidad and of Barbados are a continuation, en echelon, of the crystalline axis of the promontory of Paria. The folded Cretaceous and Tertiary of the central and southern parts of Trinidad represent a continuation of the folded sedinlents of the Paria district of Venezuela. Possible Oil-bearing Areas The volcanic islands of the inner arc of the Lesser Antilles may be excluded from consideration; these include Saba, St. Kitts, Nevis,

Jan 1, 1923

By Ray Arms

This paper includes a brief classification of dry-cleaning devices, with a theoretical discussion of the principles involved. It outlines the methods of handling dust and screening difficulties at the McComas plant, as well as other plants that are being constructed and other dry-cleaning devices being developed. It describes the American Pneumatic Separator and discusses the sizing required, the effect of moisture in the raw coal, disposition of the middlings, and other aspects of the process. It gives s results of tests on various coals, and results of operation at Raton and McComas. DRY CLEANING, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group' also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc.

Jan 3, 1924

By T. C. Mendenhall

All persons, actively engaged in your profession, must have a natural interest in the subject of weights and measures. All members of the engineering profession have to do with operations of weighing and measuring—some with measuring more than weighing, and some with weighing more than measuring—but all with both of these processes to a greater or less degree. Methods of weighing and measuring have improved constantly from the earliest times and have kept pace with the advance of other technical processes. It is, therefore, believed that you will be interested in a few remarks concerning some of the more recent advances in relation to the establishment of decimal standards of length and mass in this country. Before speaking of this, I will refer very briefly to some facts which may not be very generally known regarding our customary system of weights and measures. Although the yard is universally accepted as the unit of length, and the pound as the unit of mass, it is not generally understood, I believe, just in what respect the yard is the unit of length, or the pound the unit of mass. That is to say, it is not generally known in what degree these units have been legalized by Acts of congress. Doubtless, many of you are familiar with the facts which I will briefly recapitulate. The Constitution of the United States authorizes Congress to establish a system of weights, measures and coinage. The establishment of a system of coinage, as you know, was one of the first acts of the government, and the system then adopted is certainly one of the most perfect, if not the most perfect, that the world has yet seen. But, although Congress had the power to establish a system of weights and measures, it has never yet seen fit to exercise this power; that is to say, Congress has never yet

Jan 1, 1890

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of 'style'- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie's remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By Foster Bain

THOUGHTFUL people have raised questions as to how long nature's bank could continue to accept our drafts. These questions came to the fore so persistently, and there were so many evidences -such as the failure of natural gas in Indiana, the increasing scarcity of lumber in the Lake Superior region, the progressive sterility of Southern farm lands, the choking of the Sacramento River by tailing-point-ing to possible danger from overdraft or to misuse of resources and opportunity, that President Roosevelt called a conference which assembled at the White House on May 13, 1908, to consider these and related questions. This, the first great Conservation Congress, had a wide and beneficial influence on the thought of the world. It profoundly influenced the course of succeed-ing events and, while even yet there are sharp dis-agreements as, to the wisdom of much that has been done in the name of conservation, I believe that thoughtful men, and engineers especially, agree that the time had come when sharp attention was properly called to the waste that accompanied development of our resources. RESOURCES LARGE BUT NOT INEXHAUSTIBLE In 1908 there was a surprisingly large number of men, who should have known better, prepared to argue that our resources are "inexhaustible." No competent mining engineer, of course, believes that, as regards minerals at least. They may be, and, in most cases, fortunately are, large; as to many of them our knowledge is too general to permit measuring the reserves; but we know now, and I think the public appreciates, that there is a limit to our supply of gas, oil, coal, iron, and metals. Indeed, with the inten-sive study made necessary to meet the demands of the war, and the more careful accounting required by the newer systems of taxation, depletion has become a common word, and that mines are wasting assets has become a platitude.

Jan 8, 1922

By W. A. Boyer

MINE hoisting ropes can be loaded to capacity only when the strength of each component is exactly known. Characteristic curves provide this information. When load and rate of acceleration are specified for an individual rope, the characteristic curve assumes a predetermined shape. The factor of safety, is the value drived by dividing the breaking strength of the rope by the total stress on the rope where it goes over the sheave wheel. Total stress is made up of the weight of skip and cage, weight of ore, weight of rope between sheave and rope clevise or attachment, friction load, and acceleration force. Bending stresses are neglected in this discussion, as sheaves and drum di- ameters are assumed to be large enough to reduce these stresses to a negligible value. Fig. 1 gives a family of characteristic curves for 13/8-in. improved plow steel hoisting ropes of 6 x 19 or 6x21 construction with hemp core. The curves will hold for all rope sizes of this specified quality when they are subjected to an acceleration rate of 1.608 ft per sec2. As acceleration rates of most deep shaft hoists are close to this value, this family of curves is presented as a standard. Deviation is slight for other rope sizes. Note that for 0, which is the most important, the deviation is within the width of the line on the graph. In a comparison of values for ropes of 5/8-in. and 21/4-in. diam the deviation ranges from a maximum 1.2 pct at 0 ft to 0.6 of 1 pct at 5000 ft. The value of 5.55 is the same for all ropes at 2500 ft. The tabulated columns to the left of the curves are values of total connected load for each size of rope from 5/8-in. to 21/4-in. diam inclusive. With each of these connected loads the safety factor characteristic curve for the rope will be as indicated.

Jan 1, 1957

By Arthur H. Redfield

The West Indies are the summits of a submerged mountain chain, the continuation of which must be sought in the mountains of central Honduras. In Haiti, the chain divides, one branch passing through Jamaica and the other through Cuba, the Cayman Islands, and the Misteriosa bank. Suess divides the West Indies into three zones: The first zone is entirely of volcanic origin and includes many recent volcanic cones. It includes the arcuate string of islands, which extends from Saba and St. Kitts to the Grenadines and Grenada. The western half of Guadeloupe belongs to this group. The second zone consists of a geanticline, of which the sedimentary rocks range from the Jurassic to the Quaternary, but consist chiefly of Lower Tertiary sediments. In the west it is broad, including the whole of the Greater Antilles; but in the east it is restricted to a narrow belt, which includes the Virgin Islands (except Anegada), Anguilla, St. Bartholomew, Antigua, the eastern part of Guadeloupe and part of Barbados. The islands that compose the third zone are flat and low. Like the second, this zone is broad in the west and narrow in the east; it includes the Bahamas, Anegada, Sombrero, Barbuda, and part of Barbados. Geologically, Florida and the plain of Yucatan may be regarded as belonging to it. Trinidad and Tobago, though geographically adjacent to the Lesser Antilles, are geologically a detached part of the South American continent. The crystalline complexes of northern Trinidad and of Barbados are a continuation, en echelon, of the crystalline axis of the promontory of Paria. The folded Cretaceous and Tertiary of the central and southern parts of Trinidad represent a continuation of the folded sedinlents of the Paria district of Venezuela. Possible Oil-bearing Areas The volcanic islands of the inner arc of the Lesser Antilles may be excluded from consideration; these include Saba, St. Kitts, Nevis,

Jan 1, 1923

By W. C. Kerr

A brief sketch only is here intended, with a few illustrations, in order to give a general notion of the character and structure of these veins. I have stated elsewhere, several years ago, that these veins were wrought on a large scale and for many ages by some ancient peoples, most probably the so-called Mound Builders; although they built no mounds here, and have left no signs of any permanent habitation. They opened and worked a great marly veins down to or near water-level; that is, as far as the action of atmospheric chemistry had softened the rock so that it was workable without metal tools, of the use of which no signs are apparent. Many of the ladgest and most profitable of the mines of the present day are simply the ancient Mound Builders' mines reopened and pushed into the hard undecomposed granite by powder and steel. Blocks of mica have often been found half imbedded in the face of the vein, with the tool-marks about it, showing the exact limit of the efficiency of those prehistoric mechanical appliances. As to the geological relations of these veins, they are found in the gneisses

Jan 1, 1880