Search Documents

By Herman Poole

When finely divided ferrous sulphide, FeS, is roasted at a moderate, carefully-regulated temperature, the iron and sulphur are oxidized, the first products being probably ferrous oxide and sulphurous acid. In the presence of oxygen of the air the ferrous oxide soon becomes ferric oxide, and, in the presence of oxygen and the ferric oxide, the sulphurous acid oxidizes to sulphuric acid. These facts are well known, having been established by Plattner many years ago. As a further reaction, some of the sulphuric acid parts with a portion of its oxygen to oxidize more ferrous oxide to ferric oxide, and a portion of it escapes uncombined, or else unites with the iron oxides to form sulphates. Ferrous sulphate is usually soon oxidized to ferric sulphate, and if the heat becomes sufficient, this is then decomposed into sulphuric acid and ferric oxide. As a result of these reactions a mass of more or less pure ferric oxide is formed which is generally made porous by the escaping gases and, if rabbled properly, practically all the sulphur is expelled. If ferric sulphide or ordinary pyrites, FeS2, is roasted, a portion of the sulphur sublimes and usually burns to form sulphurous or sulphuric acid, although at times and under favorable conditions, some of the sulphur is driven off uncombined, and can be collected as such. Under ordinary methods of roasting, however, only a small portion escapes combustion. By the combustion of the sulphur an increase of heat is developed and, as a consequence, the reactions mentioned take place more rapidly and actively,—more sulphuric acid is formed and the oxidation is more complete—nearly all the iron being left as ferric oxide with practically no sulphate or ferrous oxide. When the iron sulphide is in lumps the roasting proceeds generally as with fines, but with some changes due to mass. The

Jan 1, 1906

By Lawrence Addicks

Some three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed by constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and was fired with fuel oil. A run of several hours yielded excellent nodules. The ki1n showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal, of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per ton of flue dust shown on the test and as fuel oil at that time was selling around 2 1/2 c. per gallon it was decided to let it go at that. A 60 by 6 ft. kiln was decided on, as that size is standard in cement practice, although fast being replaced by much larger ones with their greater fuel economy, and as it fitted in the building space available. A 6-in. brick lining brought the net diameter down to 5 ft. The inclination

Jan 1, 1915

By Samuel S. Wyer

Discussion of the paper of SAMUEL S. WYER, presented at the New York meeting February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 263 to 279. DAVID T. DAY, Washington, D. C.-I would like to ask whether the court decisions quoted in the paper are general, or do they represent one side of the case; if so, are there any decisions that represent more than one side of the case? Are they of general application, or do they affect only one side? Also, what is the difference between a pump and a compressor from the standpoint of the natural-gas industry? I notice stress is laid on the word "pump" in. connection with some of the legal decisions, and then it is stated. that they must not pump or compress above 300 lb. The question is, is a pump a compressor and a compressor a pump, under certain conditions? SAMUEL S. WYER, Columbus, Ohio.-Answering the first question, I will say that the decisions cover both sides of the case very thoroughly, and are uniformly on the side that a company is justified in the use of gas compressors; in other words, there are no decisions holding it to be illegal to use gas compressors, with the exception noted in Indiana, Kansas, and Oklahoma where you cannot go below atmospheric pressure. In regard to the second question, I think the engineers and the gas operators themselves are responsible for the confusion. It is because the use of the term "pump" is almost universal, and so many people have obtained the idea that the primary function of a gas compressor is to pump air into the gas, in order to increase the consumers' gas bills. I appreciate that it is very hard to draw a clear line of demarcation. between a pump and a compressor. The distinction I have always made myself, and which I think is a logical one, is that you do not get the pumping action until you get below atmospheric pressure. As far as the compression end is concerned, there is only one State, namely, Indiana, that has any statutory limitation with regard to how high the pressure may be increased in order to put the gas into the transmission lines. The State law in Indiana limits the maximum pressure to 300 lb. per square inch.

Jan 5, 1916

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Frank Nicholson

Copper ore was first noticed in Ste. Genevieve County in 1563. The diswvery mas made by a German farmer named Simon Grass, who had occasion to make a road from his farm down the hill into the neighboring valley, and while so engaged noticed pieces of a green-colored mineral, some of which he collected. Not knowing the character of the ore he had found, and supposing it to be valua ble for its brilliant green color only, he carried a piece with him into the town of Ste. Genevieve and showed it around the various bar rooms as a curiosity. No special attention was paid to the matter until nine years later, when Mr. 0. D. Harris sent a specimen of the ore to Dr. Theodore Fay, of St. Louis, for analysis. This analysis, which was the first ever made of Ste. Genevieve copper ore, showed the specimen to contain : Copper,. .........17.75 per cent. Zinc,..........3.21 " Iron........... 24.50 " Sulphur ..........1.09 " Organic matter, silica, carbon, and oxygen,. .. 53.45 " 100.00 " From this analysis it is evident that the sample was taken from near the surface, and was probably recognized by its green color. The almost entire absence of sulphur proves it to be an oxidized form. There is on file, at the office of the Ste. Genevieve Copper Works, a paper* giving three arsays of the ore made in 1875 by Henry B.

Jan 1, 1882

New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. WILLIAM A. POMEROY. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia FRANK A. ROSS Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 3, 1915

By Jay A. Carpenter

This paper deals with only one step in the treatment of ore at the West End mill; not because the other steps are repetitions of practice in other mills, but because in this particular step there is in use the Trent agitator: This device, although it has apparently failed in many mills, is here giving excellent service and has proved to be well adapted for making a thorough replacement of pregnant solution with a minimum amount of barren solution. The strong and weak points of this agitator, its present simple construction, and its use as a thickener for agitator or battery pulp are features of interest; but perhaps the point of greatest interest to the metallurgist in this day of continuous decantation is its use in a series of tanks for slime treatment by the replacement method. The agitating department of the West End mill consists of six redwood tanks, 24 ft. in diameter, 18 ft. high, each equipped with a Trent agitator, a centrifugal pump, and a motor. The pulp is transferred by a pump from the top of a flat-bottomed tank to a set of arms and nozzles in the bottom of the tank, at just sufficient pressure to cause the arms to revolve. The streams from the many nozzles keep the bottom of the tank clean, and these streams, coupled with the effect of the revolving mechanism and the ascending current, keep the pulp in constant motion and of constant gravity. These agitating tanks hold 90 tons of dry slime and 202 tons of solution with a 1.24 pulp, our ore having a specific gravity of 2.7. This capacity is about 10 per cent. in excess of the standard 15 by 45 ft. Pachuca tank. The tanks are connected in one series for continuous agitation, the pulp for each agitator being drawn by its pump through a branch suction from near the top of the preceding tank and delivered to the bottom of the tank by the agitator arms along with the regular pulp of that agitator. This method works automatically, since the flow through the branch suction varies directly with the difference in head of the two tanks. The chance for new pulp to pass out quickly is, therefore, much less than in many other systems of continuous agitation, since the new

Jan 1, 1916

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By Charles M. Ryder

IN presenting this paper to the Institute I beg to mention, first, the results which I have obtained and the apparatus which I have employed, and to follow this with a brief description of the steps by which I have perfected this process. My present mode of testing is as follows : I obtain, either from the furnace or from the finished product in any stage in which it may chance to be, a small test-piece, usually about 4 of an inch square by 3 1/2 inches in length. I place this test-piece upon the poles of an ordinary electro-magnet, for about one minute, and thus magnetize it to its extreme limit. I then place it upon an indicator (which I will shortly describe), on which indicator there is already placed a piece of steel of similar form which has been magnetized in the same manner, the percentage of carbon of this second piece being definitely known. I then, by means of a scale, which forms part of the indicator, marked in degrees of carbonization, read the exact percentage of carbon contained in the piece under examination. My apparatus consists of an ordinary electro-magnet, connected with a suitable battery of moderate power, by which I magnetize the pieces as before described, and of an indicator which consists of a magnetic needle suitably mounted or suspended, so that it is free to deviate a few degrees only from the zero point, and having a rest, which is used to check the vibrations when in use, and to support its weight when not in use. At a right angle to the natural position of the needle I have a scale about 3 feet long, the zero point of which coincides with the natural position of the needle. This scale is marked in each direction from the zero point in degrees of carbonization. The marking of the scale is in accordance with the following rule: Taking the carbonization of the steel as a basis, I maintain the same proportion between the squares of the distances on the scale as exists between the percentages of carbon in the steel, for instance, if .08 of

Jan 1, 1877

By J. D. Meakin, H. G. F. Wilsdorf

An etching technique.has been used to investigate the dislocation structure of deformed @-brass single crystals. Isolated single ended pileups have been observed, and it is shown that, in certain cases, the configurations of such pileups agree with theoretical predictions. Many discrete pileups within heavily deformed regions have also been detected and the influence of surrounding dislocations on these groups are reported and discussed. Divergences between the experimental and theoretical spacings in the isolated pileups and the origin of the stress maintaining the pileups are discussed. THE spatial configuration of a linear array of identical dislocations has been evaluated theoretically by Eshelby, Frank, and Nabarro.' Of particular interest is the equilibrium spacing of a series of dislocations under a uniform shear sti-ess when the leading dislocation is held fixed in the lattice; such an array is termed a single ended pileup. Eshelby, Frank, and Nabarro' found that an explicit analytical solution to the problem of n dislocations in a pileup is not possible, but they were able to derive approximate formulae applicable under various limiting conditions. An alternative method of determining the equilibrium configuration was proposed by Leibfried and Leibfried and Haasen in which the discrete dislocations are replaced by a continuous dislocation density. This technique was used by Head and Louat to solve in first approximation, a number of problems of particular interest, eg., single and double ended pileups. Head has also solved numerically a number of specific configurations involving up to six dislocations. Recently Kuhlmann-Wilsdorf has obtained numerical solutions for single-ended pileups containing between three and seventy dislocations, thus making possible a comparison between appropriate experimental results and accurate theoretical values. The considerable use of the pileup concept in theories of plastic flow has stimulated a number of attempts to observe such arrays experimentally. There is of course considerable intrinsic value in revealing an isolated pileup because a direct check on the elastic theory of dislocations then becomes possible. The only technique generally applicable for studying pileups in bulk metal specimens is selective etching of the point of emergence of individual dislocations. Confining our attention to etching studies which have revealed pileups, the earliest reported work

Jan 1, 1961

By Allen J. Johnson

Anthracite coals have been divided into three groups: (I) meta-anthracite, a high-carbon coal that is usually very slow to kindle and difficult to burn, at least on conventional equipment; (2) anthracite, a high-carbon low-volatile coal of widely accepted value as both a domestic and industrial fuel; and (3) semianthracite, a coal lying between anthracite and bituminous coal in carbon and volatile content, and also, generally speaking, in burning characteristics. Anthracite Groupings The technical differentiation between these groups, as defined by the A.S.A.-A.S.T.M. Sectional Committee on the Classification of Coals, is as shown in Table I. Tables 2 and 3 show typical analyses of anthracites and semianthracites and Figs. I to 3 show graphically the range of analytical samples. Table 4 shows the commercial sizes of coals. Meta-anthracite and Graphitic Anthracite Typical analyses from virtually every field in the United States indicate that there are few if any extensive deposits of meta-anthracite. Some of the anthracites of Rhode Island contain almost negligible quantities of volatile and would thus fall into the meta-anthracite grouping on a basis of analyses alone. However, their other characteristics indicate that it is doubtful whether they should be considered as fuels at all, but rather as graphite. In fact, this material is being mined for use as foundry facings and furnace linings.4 A typical analysis of Fenners Lodge graphite,4 from Rhode Island, is: graphitic carbon, 55.9 per cent; silica (ash), 40.6; sulphur, 1.6; moisture, 1.9; volatile, o. Other Rhode Island coals possess percentages of volatile that would throw them into the normal anthracite rather than the meta-anthracite class. However, this "volatile" is nearly all noncombustible,3,4 being composed almost entirely of carbon dioxide and inert gases, therefore its definition as volatile is open to discussion, leaving the exact classification of the fuel a moot question. One factor is certain, Rhode Island coal is so different from nor-mal anthracite in both analysis and burning characteristics that it should have a

Jan 1, 1944

By Craig R. Barrett

The influence of the stress dependence of the dislocation density on the overall stress dependence of The steady-state creep rate is discussed. Experimental measurements of dislocation densities and creep rates jor an Fe-3.1 pct Si alloy tested over a wide range of stress are presented which indicate a close correlation between the two quantities. EXPRESSING the stress dependence of high-temperature steady-state creep rates has been the subject of numerous investigations over the past decade. From these investigations have emerged a few general equations which fit most of the available data reasonably well. Garofalo 1 has proposed that for a wide range of stress and temperature the creep rate, i, can be expressed by a relationship of the form: where A, ß, and n are temperature-dependent and is the applied stress. Eq. [I] gives a stress dependence of a at low stresses and exp(nßo) at high stresses, both consistent with experimental observation where n = 5. A number of other investigatorshave proposed a similar expression where: where m and w are in general functions of temperature. Theoretical justification for Eqs. 111 and [2J comes from two different approaches, theories based on dislocation glide3-5 and theories based on the balance between work-hardening and recovery.' Dislocation glide theories predict where p is the mobile dislocation density and V is the activation volume. In order for Eq. [3] to predict a on stress dependence at low stresses with n = 5, it is necessary for p to be a strong function of stress, about proportional to u3 or u4.436 Recovery models of creep start with the general expression:' where r is the recovery rate and h is the work-hardening rate, and then employ a detailed model to determine the stress dependencies of r and h. As example, weertman2 has described a model based on pile-up hardening which results in an expression similar to Eq. [2] with m = 2 and p = 2.5. A recent, seemingly more general approach suggested by McLean is to use Friedels dislocation network growth expression to calculate the stress dependence of r. This model predicts r = p 3,2 and, as h is taken to be a relatively weak function of stress, the stress dependence of i should be about proportional to p3, 2. Once again, it is required that p be a strong function of stress to yield i This recovery model is by no means complete as the stress dependence of network growth is calculated in the absence of an applied stress meaning that r should probably be a stronger function of stress than given by p3, 2 and also some recent work by Mitra and McLean8 suggests that the stress dependence of h may be as large as Because of the importance of the stress dependence of p in determining the overall stress dependence of the strain rate it seems reasonable to examine this relationship in some detail. Measurements made on dislocation densities present during high-temperature steady-state creep generally obey the following relationship a =o0 + aGVWp [5] where uo is usually called a friction stress, a is a numerical constant about equal to unity, G is the shear modulus, and b is the Burgers vector. Depending on the magnitude of uo, data obeying Eq. [5] can give rise to a range of stress dependencies of p. For example, if we assume that the expression where 6 is some constant, adequately represents the stress dependence of p over a range of o, then from Although Eq. [6] obviously breaks down when u 5uo for uo 6 can vary over a wide range of values. In particular, if u > a, > 0 then 6 will be greater than 2. As an example the data of Ishida and McLean are plotted in Fig. 1 showing excellent agreement with dynes per sq cm) and also showing good agreement with a p cc u3 dependence when plotted on a log-log basis. As oo increases 6 tends to increase and correspondingly the stress dependence of the predicted creep rate should also increase,* as-

Jan 1, 1968

By P. Duwez, L. Zwell

In recent years, the problem of pressing metal powder in a die has received much attention. The question has been the object of a Symposium held in New York in March 1947 under the sponsorship of the AIME; an excellent review of the subject may be found in Ref. 1. Various experimental techniques have been used to study the behavior of the powder in a die cavity. Two methods have been particularly successful; one consists of measuring the density distribution²,³ and the other makes use of a lead grid in the powder during pressing.4 In the present study, the pressure at various points on the bottom and the sides of a die 1.50 in. in diam was measured by means of small piston dynamometers and resistance sensitive strain gauges. In order to correlate the results with previous investigations, the pressure distribution inside the compact has also been determined by an indirect method based on density measurements. Strain Gauge Measurements of Pressure on Side and Bottom of Die A schematic drawing of the die used for measuring side pressures is shown in Fig 1. The pressure gauge consists of a 0.25-in. diam piston A which transmits the pressure to a dynamometer B, on which two Baldwin Southwark type 4-14 strain gauges are fastened 180" apart. Because the installation of several dynamometer assemblies along the side of the die would have been difficult, the pressure distribution was obtained in successive tests in which the distance from the gauge to the bottom of the compact was adjusted to different values by changing the length of the bottom piston. The dynamometer, disassembled from the die, was calibrated under compressive loads and showed a 1.00 ohm change of resistance for every 15,300 psi change of pressure (750 lb load change). All the strain gauge measurements were made with a null type Leeds and Northrup Wheatstone bridge. The sensitivity of the method was better than 1 pct and the accuracy was within 2 pct. These values were considered satisfactory in view of the rather large scatter in the measurements introduced by the random variation in packing the powder in the die. The stable ambient conditions and short time involved in the taking of observations made temperature compensation unnecessary-. The pressure distribution on the bot-

Jan 1, 1950

By W. G. Matteson

BENJAMIN L. MILLER, So. Bethlehem, Pa.-In discussing the question personally with Mr. Matteson I have found that he simply proposed this as a suggestion and he recognizes, as well as a great many other oil geologists and oil operators, that to put into practice such a suggestion would mean the overcoming of many difficulties. Yet perhaps it may be possible to overcome the various objections that may be offered. Undoubtedly one of the most serious objections is that of incomplete and inaccurate well records. Faulty records are worse than no records at all. Perhaps, however, definite instructions and insistence on their observation may remedy this defect after a time. THE CHAIRMAN (M. L. REQUA, San Francisco, Cal.).-This subject is a. very important one, but just how far the National Government can go in .taking action is a question: It involves, of course, the question of State rights. California, I .think, has done very well up to date and probably will do better in the future. The law that was passed at the session of the Legislature 2 years ago is working as satisfactorily as anything of that kind can work with so little experience to guide the framers of the statute. We recognize in California the vital necessity of conserving the oil of the State. We have come to the conclusion that there is not as much oil ,in California as we thought there was. In the month of December the State drew on its oil stocks to- the extent of 1,800,000 bbl. and I think that the January statistics will show probably as much more. There is more or less of a.: panic at the present time among the large marketing concerns regarding the question as to where they are going to get their oil for future requirements

Jan 4, 1917

By V. Annamalai, J. B. Hiskey

The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol- 1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol- 1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 1, 1979

By M. R. Goldick

The Roan Antelope concentrator was originally designed with a nominal milling capacity of 6000 tons of copper ore per day but this was subsequently considerably exceeded. In broad outline the plant consisted of two No. 30 McCully gyratory crushers for coarse crushing, five 5½-ft Standard Symons crushers in open circuit for secondary crushing, ten No. 98 Marcy ball mills arranged in five sections, each two-mill section with primary and secondary Dorr classifiers for two-stage grinding. One stage of flotation roughing was followed by two stages of cleaning, all in airlift type pneumatic flotation machines, with the final concentrates filtered on Oliver drum filters. Tailing was thickened in a 250-ft Dorr traction type thickener before pumping to the tailing dam. Concentrating operations commenced in June 1931, on the completion of the first two ball-milling sections and output was increased during the next few months as the remaining sections were finished. From the start, very few technical difficulties were experienced but a number of evolutionary changes have been made as a result of operating experience and the availability of improved equipment. These have resulted in plant and ore-flow alterations although the general scheme of ore treatment remains substantially as before. The main changes to date were the installation of a new crushing plant at Storke shaft, some 7000 ft west of the original Beatty shaft; the completion of a two-stage secondary crushing plant; an increase of 20 pct in ball-milling capacity; a change-over from pneumatic to a mcchanical type of flotation machine for flotation roughing; the reduction of flotation cleaning from two stages to one stage. Ore Treated Typically the ore treated consists of metamorphosed shales and sandstones with shales as the principal mineral-bearing rock carrying chalcocite, bornite and chalcopy-rite as the main copper minerals. Chalcocite predominated in the original eastern end of the ore body but there is a pronounced trend to an increased proportion of the copper-iron sulphides as mining proceeds westward. Although the ore can be described as soft, this advantage is offset by the extremely fine dissemination of the copper minerals which calls for a high degree of comminution of the ore (go pct minus-zoo mesh Tyler standard) to give a reasonably satisfactory separation of mineral from gangue. Latterly, there has been a tendency for the ore to become harder as shown by a reduction in the ball-milling rate from a previous figure of over goo tons per ball-mill day to the present output of some 800 tons. Chalcopyrite is not so finely disseminated and has also proved more amenable to flotation than chalcocite. Nonsulphide minerals are mainly the so-called oxides such as malachite, cuprite and melaconite with some chrysocolla and

Jan 1, 1949

By W. F. White, W. R. Beloff, B. C. Dorwart, G. W. Jaworski

INTRODUCTION The rigid inclusion stressmeter is a relatively low-cost instrument developed by Hawkes and Bailey (1973) and was originally intended to monitor stress changes in mine pillars subjected to uniaxial stress changes. In this regard, this instrument has found considerable use by the mining industry. More recently, there have been attempts to use the stressmeter for determination of more general changes of the in situ rock stress. This paper reports on a study to characterize the performance of the rigid inclusion stressmeter for this application and presents results on the effect of anisotropic stress changes. These stress changes must be accounted for to properly analyze general changes of the in situ rock stress. BACKGROUND INFORMATION The rigid inclusion stressmeter is an instrument designed to measure variations of the in situ stress around a borehole. The stressmeter studied in this work, is manufactured by Irad Gage, Div. Creare Products, Inc. Lebanon, New Hampshire. It consists of a stiff hollow steel gage body that is preloaded across a borehole diameter. The preloading is activated by sliding a wedge between an upper platen and the gage body. Changes in the in situ stress result in slight deformations of the gage body. These deformations affect the stress in a highly tensioned wire that

Jan 1, 1982

By N. M. Saum, W. T. Caneer

Uranium may be in short supply due to the predicted energy needs in the coming years. As a result of this, a new surge of uranium exploration is underway accompanied by the refinement of numerous exploration techniques. One such technique is the monitoring of radon gas in surface soils and rocks as a guide to subsurface uranium deposits. The Colorado School of Mines Research Institute became involved in radon studies in 1967 on a project for the Atomic Energy Commission. Since that time the Institute has conducted numerous radon surveys for a large number of companies which have been active in uranium exploration. The objective of this paper is to relate the techniques utilized by the Research Institute and the results of some of the studies performed. Most of the studies performed by the Research Institute were related to roll front, sandstone-type uranium deposits. However, we have performed radon studies in various other types of rock. For those who may not be familiar with the application of radon "sniffing" in soils and rocks, a brief descriptive background should be given. The following question may be asked-why use radon as a guide to uranium mineralization? Some of the answers to this question are:

Jan 5, 1974

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.&apos; This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,&apos; a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969