Search Documents

By John C. Gifford, Charles L. Thomas

A unique and reproducible method is presented for the determination of water vapor in tough pitch wire bar copper. The procedure involves reduction of the water vapor with molten aluminum to form hydrogen, which is subsequently measured by mass spectroscopy. Average water vapor pressures within the porosities of the wire bar samples are calculated. Correlation is to exist between the specific gravities of the samples and their measured water vapor contents. The method should find application as a very sensitive means of detecting hydrogen embrittlement in copper. The nature and quantity of gases evolved and retained during the horizontal casting of tough pitch wire bar copper have long been of interest to the metallurgist. Considerable work has been done at this laboratory on the determination of these gases. The work has involved not only qualitative but also quantitative analysis, so as to provide a basis for a total accounting of the porosity which is associated with the cast product. From a knowledge of the gas-forming elements within the copper, and the practice of melting and protecting it with a reducing flame followed by contact with a charcoal cover in the casting ladle, the gases which one might expect to find in the pores of the cast product are sulfur dioxide, carbon monoxide, carbon dioxide, hydrogen, and water vapor. Hydrogen sulfide, nitrogen, and hydrocarbons would be other possibilities; however vacuum fusion-mass spectroscopy techniques employed at this laboratory have shown that no hydrogen sulfide and only traces of nitrogen and methane are present. It is highly improbable according to phillipsl that any sulfur dioxide could be evolved in wire bar copper with 10 ppm or less sulfur under normal freezing conditions. Mackay and smith2 have noted that porosity due to sulfur dioxide only becomes noticeable at concentrations above 20 ppm S. Investigation of carbon monoxide and carbon dioxide by a variation in the method of Bever and Floe showed that these two gases could only account, at 760 mm and 1064°C (Cu-Cua eutectic temperature), for a maximum of about 25 pct of the total porosity in a wire bar having a specific gravity of 8.40 g per cu cm. phillips' has noted that no normal furnace atmosphere is ever sufficiently rich in hydrogen to cause porosity in copper from hydrogen alone. In addition, using a hot vacuum extraction technique for hydrogen,4 values have never been observed in excess of 10 ppb in tough pitch wire bar. On the basis of the preceding considerations of gases in tough pitch wire bar, only water vapor is left to account for the major portion of the porosity. Direct determinations of water vapor are virtually impossible at low concentrations by any presently known technique, due to adsorption and desorption within the walls of the apparatus used.5 The present investigation deals with a method for the determination of water vapor by an indirect procedure, using molten aluminum as a reducing agent to form hydrogen according to the reaction: 2A1 + 3H2O — A12O3 + 3H2 The evolved hydrogen can then be measured quantitatively by mass spectroscopy. EXPERIMENTAL A 10-g piece of 99.9+ pct A1 was charged into a porous alumina crucible (Laboratory Equipment Co., No. 528-30). Fig. 1 shows the crucible in place at the bottom of an 8-in.-long quartz thimble. A funnel tube with two l1/8-in.-OD sidearms extending at a 90-deg angle from each other was attached to the top of the thimble. One of the sidearms was joined to the inlet system of the mass spectrometer (Consolidated Electrodynamics Corp. Model 21-620A) via a mercury diffusion pump situated between two dry-ice traps. The copper samples were placed in the other sidearm, followed by a glass-enclosed magnetic stirring bar for pushing the samples into the crucible. All ground joints were sealed with vacuum-grade wax. The entire system was evacuated and the aluminum was heated with a T-2.5 Lepel High Frequency Induction Furnace for 21/2 hr at a temperature visually estimated to be 900°C. The temperature was then lowered and the hydrogen was monitored on the mass spectrometer until it was given off at a constant rate of about 4 to 5 1 per hr. This rate corresponded to a slope of 2 to 3 divisions per min on the X3 attenuation of a 10-mv recorder at a hydrogen sensitivity of approximately 100 divisions per 1. A micromanometer (Consolidated Electrodynamics Corp. Model 23-105)

Jan 1, 1969

By J. M. Dupouy, R. A. Rawe, M. B. Bever

The aging characteristics of a titanium alloy containing 13 pct V, I1 pct Cr, and 4 pct A1 have been investigated by hardness measurements, X-ray diffraction, and metallography. The P phase decomposes into 0 + a, and 0 + a, + TiCr, above about 1050°F; below this temperature a transition phase, believed to be w, precipitates first, followed by a, and TiCr,. The observed hardening is attributed to these reactions. Cold working of solution-treated specimens accelerates hardening and raises the hardness level attained. A TTT diagram is proposed. NEW titanium-base alloys, designated as "all-beta," have recently been developed. These alloys contain large amounts of P-stabilizing elements such as molybdenum, chromium, or vanadium. When cooled from the solution temperature, they consist only of P; in particular, the martensitic a,' phase does not form.

Jan 1, 1961

By Bruce A. Kennedy, Richard M. Stewart

Slope stability has now become a practical tool in the design and operation of open pits. The selection of slope angles is a critical decision that can have far-reaching effects on the accumulated cash flow and the overall profitability of a mining project. Slope failures can now be dealt with in a number of ways. Two methods - the total removal and the partial unloading of a failing zone-have been practiced for many years. However, with the refinement of monitoring techniques, open pits can now learn to live with a slide and even turn a potential loss into a gain. There are various techniques, such as presplit blasting, drainage systems, and artificial stabilization, which can be applied immediately in an existing open pit to improve the stability of the pit slopes. The technology of slope stability will play an important part in the future mining of low grade, previously marginal orebodies, which will have to be exploited if the mineral needs of the world are to be met.

Jan 1, 1971

By F. Louis Grammer

The iron industry has been so markedly the cynosure of all eyes, that a sense of weariness has overtaken many on-lookers, and a new wonder is desired. While the commercial phase of the iron industry has necessarily engrossed the public attention and probably is the more worthy of record, still the mechanical and metallurgical phases have recorded conspicuous advances and merit attention. In order to appreciate the present condition of blast-furnace practice, it is necessary before enumerating the advances made during the past decade to give a brief discussion of the tendencies in the methods of administration as well as the conditions governing supremacy, for these factors have modified the aims of the manager. It might also be well to apologize for a record of the advances made during such a short period as a decade, were it not that, for the individual, time is marked as much by the impressions recorded on the brain as by the jumps of the second hand of a watch. Furthermore, this article is written in order to carry out a project of the late Dr. Egleston, to have a record made each decade. I regret that the data collected by him, and forwarded to me, end with 1896, and therefore do not include the interesting results which followed the introduction of Mesabi ores. The perusal of the notes is melancholy reading, somewhat like the feelings we experience in going through a graveyard. It is a record made up of so many plants, which have ceased to be factors in the iron world, if they are not entirely moribund. Historically, they would be interesting, emphasizing as they do the abnormal and somewhat overestimated importance of furnace lines, taken without proper reference to volume of blast and nature of stock used. I regret, however, that the time at my disposal does not permit of this presentation.

Jan 1, 1905

By E. Brunner, E. S. Mardock

A method of measuring oil saturations in cores or sand packs by neutron scattering is described. This method permits local SatUrations to be measured in a core enclosed in a steel pressure vessel without interrupting the flow. calibration data and a saturation distribution measurement obtained with the apparatus are included by way of illustration. Introduction In laboratory flow experiments designed to study the mechanism of oil production it is frequently necessary to measure the oil saturation in a core or sand pack containing Oil, gas, and perhaps brine. It is sometimes desirable that the saturation measurement refer to a relatively small portion of the core, so as to eliminate end effects; that it be made without interrupting the flow, and that it be applicable to a core enclosed in a steel Pressure vessel capable Of withstanding the Pressures encountered in petroleum reservoirs. None of the usual methods of measuring saturation meets all Of these requirements. To measure the gas saturation by observing the apparent compressibility of the gaseous Phase1 would require the interruption of the flow and would give an average saturation for the whole core. An electrical conductivity method is available for measuring brine saturations,2,3 but it is not applicable to oil. A radioactive tracer might be used if a suitable substance could be found that would dissolve in the oil, emit gamma radiation, and not be adsorbed on the sand, the steel core holder, or in an aqueous- phase. The large gamma-ray background from the mass of radioactive oil in other parts of the apparatus might, however, be undesirable. There remain for the saturation measurement methods involving the absorption or scattering of some penetrating radiation produced outside the apparatus. It might be possible to use X-rays or gamma rays; but these radiations would be so much less strongly absorbed and scattered by the oil than by the steel walls of the core holder and by the sand that it seems doubtful that much precision could be attained. In a beam of neutrons, however, there is a radiation that is very penetrating and, moreover, its scattering by substances containing hydrogen, such as oil, is qualitatively different from that occasioned by other materials. It would seem possible, and has proved to be quite practicable, to measure oil saturations accurately under the required conditions by means of neutron scattering. The first, to our knowledge, to suggest neutron scattering as a means of measuring oil saturation were F. Brans and ,. A. Bottema,4 of the Amsterdam laboratories of the Bataafache Petroleum Maatschappij, who made a few preliminary experiments to test the method while they were engaged in exploring the possibilities of neutrons for well-logging purposes. A comprehensive account of neutrons and their behavior will be found, together

Jan 1, 1946

By E. S. Mardock, E. Brunner

A method of measuring oil saturations in cores or sand packs by neutron scattering is described. This method permits local SatUrations to be measured in a core enclosed in a steel pressure vessel without interrupting the flow. calibration data and a saturation distribution measurement obtained with the apparatus are included by way of illustration. Introduction In laboratory flow experiments designed to study the mechanism of oil production it is frequently necessary to measure the oil saturation in a core or sand pack containing Oil, gas, and perhaps brine. It is sometimes desirable that the saturation measurement refer to a relatively small portion of the core, so as to eliminate end effects; that it be made without interrupting the flow, and that it be applicable to a core enclosed in a steel Pressure vessel capable Of withstanding the Pressures encountered in petroleum reservoirs. None of the usual methods of measuring saturation meets all Of these requirements. To measure the gas saturation by observing the apparent compressibility of the gaseous Phase1 would require the interruption of the flow and would give an average saturation for the whole core. An electrical conductivity method is available for measuring brine saturations,2,3 but it is not applicable to oil. A radioactive tracer might be used if a suitable substance could be found that would dissolve in the oil, emit gamma radiation, and not be adsorbed on the sand, the steel core holder, or in an aqueous- phase. The large gamma-ray background from the mass of radioactive oil in other parts of the apparatus might, however, be undesirable. There remain for the saturation measurement methods involving the absorption or scattering of some penetrating radiation produced outside the apparatus. It might be possible to use X-rays or gamma rays; but these radiations would be so much less strongly absorbed and scattered by the oil than by the steel walls of the core holder and by the sand that it seems doubtful that much precision could be attained. In a beam of neutrons, however, there is a radiation that is very penetrating and, moreover, its scattering by substances containing hydrogen, such as oil, is qualitatively different from that occasioned by other materials. It would seem possible, and has proved to be quite practicable, to measure oil saturations accurately under the required conditions by means of neutron scattering. The first, to our knowledge, to suggest neutron scattering as a means of measuring oil saturation were F. Brans and ,. A. Bottema,4 of the Amsterdam laboratories of the Bataafache Petroleum Maatschappij, who made a few preliminary experiments to test the method while they were engaged in exploring the possibilities of neutrons for well-logging purposes. A comprehensive account of neutrons and their behavior will be found, together

Jan 1, 1946

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 12, 1978

By J. H. Swisher

The solubility of graphite in CaO-S2O2-Al,O3 slags was measured by equilibrating slag samples with graphite crucibles and CO gas. Carbon contents as high as 2 ut pct were obtained in CaO-saturated, CaO-A1,O3 slags, and 1.3 wt pct in slags of the composition CaO.Si0,. Although the observed conditions for Sic formation were in agreement with those predicted from thermodynamic data, CaC, was found to form at a lower temperature than predicted frotn thermodynamic data. From measurements of the equilibrium carbon content as a function of CO Partial pressure, it was found that carbide ions dissolve in CaO-A12O3 melts with a valence of minus two. The carbon content increased with CaO concentration in Ca0-Al,O3 melts and increased with SiO, content along the CaO'AlO3-CaOSi0 join in the ternary system. When solid CaC2 was added to CaO-A12O3 and CaO-SiO2-A12O3 slags, it was found that one of the oxides in the slag was reduced by the carbide (Al2O3 in the forrner and SiOz in the latter). In electric furnace steelmaking, a double-slag practice is frequently used to meet alloy specifications. Initially a flush slag, which is oxidizing in nature, is used to remove phosphorus and carbon from the steel bath. Later in the refining period, the flush slag is replaced by a highly reducing carbidic slag. When calcium carbide is formed in or added to a finishing slag, the slag is effective as a desulfurizing agent and also permits alloying elements such as chromium, vanadium, and tungsten to be added to the slag in the form of oxides. The oxides are readily reduced by calcium carbide, thereby minimizing the use of expensive ferroalloys. More work has been done on the thermodynamics of silicon carbide in slags than on calcium carbide. Baird and alor' and Kay and alor' determined the free energy of formation of Sic by measuring the partial pressure of CO in equilibrium with solid silica, silicon carbide, and graphite. Using a similar technique, they determined SiOz activities in CaO-SiOz and Ca0-Si0,-A1203 slags. Rein and chipman3 also determined the free energy of formation of Sic using slag-metal equilibrium measurements. A literature survey has uncovered only one experimental study of the behavior of CaC, in slag systems. Shanahan and cooke4 report the results of some preliminary experiments on the solubility and stability of CaC, in a CaO-A1,03 and a Ca0-Si0-A1,03 slag at a temperature of about 1500". The carbon solubility as CaC, in a slag containing 50 pct CaO and 50 pct A1203 was reported to be 0.6 pct. They also review earlier work on the binary CaO-CaC, system. A eutectic exists in this system, but various investigators disagree on the eutectic temperature and composition. eal has given an explanation for carbide furnace erruptions in terms of the thermodynamic properties of CaC,; his analysis is not based on experimental data, but on compiled data for the free energies of formation of CaC, and CO.' , These data for steel-making temperatures are all extrapolated from the results of low-temperature measurements. In the experiments described in this paper, slag samples were equilibrated with graphite crucibles and with mixtures of CO and argon or with CO gas at 1 atm total pressure for measurement of the carbon solubility. Most of the work was done on Ca0-A1203 binary slags, although in some experiments CaO-SiO, and Ca0-Si0,-A1,03 slags were used. EXPERIMENTAL Slag samples of the desired composition for the solubility measurements were obtained by blending pre-fused master slags. The master slags were prepared by fusing mixtures of reagent-grade CaC03 with either A1,03 or Si0, in a graphite crucible. The master slags were crushed, then decarburized in air in a muffle furnace at 1200O C. A schematic diagram of the apparatus is shown in Fig. 1. The source of carbon for the solubility meas-

Jan 1, 1969

By J. M. Lommel

DURING an investigation into the effect of heat-treatment on the creep properties of the magnesium alloy ZW1, (1 pct Zn, 0.6 pct Zr), the previously published methods of final polishing were found to be unsatisfactory. A new diamond-polishing technique has been developed to facilitate the study of fine precipitates in this and other magnesium alloys, and is described in this note. The sectioning and coarse grinding techniques are those of Fox and Hall,' and Hess and Cieorge.' Pre- liminary mechanical polishing is done with 6-µ, and 1-µ( grades of diamond compound on 'Microcloth' using a lubricant of 'Hyprez' oil. When the conventional technique is used with a 1/4- µ diamond wheel for the final polishing of magnesium alloys, scratching is likely to result from the abrasive action of the 'Microcloth' nap on the soft metal surface. This problem has been overcome by the use of a cream on the wheel in order to separate the specimen surface from the polishing cloth. To prepare this cream, a solution of 6-ml tri-ethanolamine in 75-ml water is stirred into 12.5 g stearic acid at a constant temperature of 80o to 90°C. The cream is allowed to cool, and is then 'whipped' to a smooth consistency with 100-ml 'Hyprez' oil. Before polishing, the diamond loaded 'Microcloth' is moistened with a few drops of 'Hyprez' oil, then a small amount of cream is worked into the nap. For the best results a wheel speed of 500 rpm should be used for polishing, and the specimen should be held by hand with a light pressure while being rotated in the opposite direction to the wheel. After polishing it is necessary to swab the specimen thoroughly in methylated spirits to remove residual cream and oil from the surface in order to avoid uneven etching and drying stains. Fig. 1 shows the surface finish obtained on a specimen by polishing on a 1/4- µ diamond wheel using the cream, and Figs. 2 and 3 the precipitate observed in ZW1 after polishing, and etching for two seconds in nitric acid 15 pct in ethylene glycol. This new diamond-polishing technique has made a valuable contribution to the programme of metal-lographic research on ZW1 and has become a routine laboratory practice for other low alloy content magnesium alloys.

Jan 1, 1961

By Irving Fatt, Robert J. S. Brown

INTRODUCTION The wettability of reservoir rocks is recognized as one of the major factors that determines their multiphase flow properties. Multiphase flow properties in turn govern reservoir performance. For this reason, the reservoir engineer is vitally interested in the wettability of reservoir rock. The production research scientist is interested in wettability because the solution of the problem of improving waterflood recovery by use of surface-active additives may hinge on a detailed understanding of the wettability of reservoir rock. Early workers believed that all reservoir rocks were preferentially water wet. Continued study soon uncovered certain rocks which had flow properties that indicated that they were preferentially oil wet. Recent studies show that there is a spectrum of wettability. Some reservoir rocks have multiphase flow properties which indicate that they have an intermediate wettability. The differences in recovery observed among different reservoirs may, in part be the result of small differences in wettability. Differences in wettability amcng reservoir rocks may be the result of differences in the fraction of the total surface area that is preferentially oil wet and preferentially water wet. Nuclear magnetic relaxation measurements may provide a method for determining the fraction of preferentially oil wet and preferentially water wet area in porous media. Measurements to be reported here were made on water-saturated unconsolidated sand packs which were mixtures of preferentially oil wet and preferentially water wet sands. The resulting data show definitely that the fraction of each wettability in these sand packs can be determined by this nondestructive method of measurement. THEORY OF NUCLEAR MAGNETIC RELAXATION The details of the theory of nuclear magnetic relaxation have been presented previously1. In this paper, only a very brief review of the theory will be given to show its application to the measurement of fractional wettability. Nuclear magnetic relaxation is a process of adjustment undergone by certain atomic nuclei when their magnetic environment is changed. They adjust, or relax, to be in equilibrium with a new magnetic field. The reason that some atomic nuclei are affected by a magnetic field is that they themselves behave in some respects like tiny magnets. In particular the proton, the nucleus of the hydrogen atom, behaves as a magnet. The proton spins, somewhat as the earth spins on its axis. The spinning charge produces a magnetic field just as current traveling in a loop of wire produces a magnetic field. No net charge is required, however; for instance, the neutron has spin and magnetic moment. When the spinning proton is subjected to an externally applied magnetic field, its axis tends to line up with the magnetic field, somewhat as a compass needle tends to line up, but the spinning proton cannot do this as easily as the needle can. The proton also has mass, and its spinning mass makes the proton behave somewhat like a gyroscope. As is well known, a force which tends to change the axial direction of a gyroscope merely causes the gyroscope to precess: lhat is, the axis begins to trace out a conical surface. The gyroscope cannot actually assume the position suggested

Jan 1, 1957

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By Hillary W. St. Clair

An equation is derived for the rote of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing. The equation takes into consideration the reaction rate coefficient, transport through the gas and through the porous shell of reduced oxide, the rate of gas flow, THIS paper describes a mathematical study of the chemical and physical processes that determine the rate of reduction of solid metal oxide with a reducing gas. The study was a part of a theoretical study leading to the development of a mathematical model for the simulation of the thermochemical behavior of the iron blast furnace. An essential feature of such and the volume of- space surrounding the sphere available for gas flow. The equation is applied to experimental data on vote of reduction of iron oxide in hydrogen. The equation serves as a model for predicting the course of reduction of a particle of. metal oxide in a shaft furnace. a model is an adequate mathematical relationship defining the rate of reaction in terms of all the important chemical and physical phenomena that affect the rate of reaction. This includes not only the reaction rate coefficients, equilibrium ratios, gas composition, and temperature, but also the relevant physical properties of the oxide, rate of gas flow, and relative volumes occupied by gas and solid. In many previous experimental studies of the rate of reduction of oxides by hydrogen or carbon monoxide, the rate of reduction was assumed to be controlled primarily by the chemical reaction at the

Jan 1, 1965

By George W. Healy, Ko Yamaguchi

In typical calorimetry the energy given off by a material under study is transferred to a water bath, whose temperature is sensed by a thermometer; for correct measurement the water bath must attain a uniform temperature to which the thermometer must respond. This introduces two sources of error, non-uniformity of the heat sink and a time lag until its temperature is registered. These errors may become important where a rapid process such as solidification of metals and alloys is being studied by means of Oelsen'sl quantitative thermal analysis. To overcome this difficulty, a calorimeter sink was conceived in which the water bath is replaced by a copper coil, which serves simultaneously as heat

Jan 1, 1967

By G. S. Upadhyaya, A. D. McQuillan

HERE would appear to be a simple relationship between the group number in the periodic table of the early transition metals and the maximum amount of hydrogen which they can absorb.' Thus group IIIA metals (Sc, Y, and La) yield a trihydride in which the metal atoms are on a fcc lattice and the hydrogen atoms occupy both tetrahedral and octahedral interstices. Group IVA metals (Ti, Zr, Hf) form dihy-drides in which the metal atoms are on either a fct or cubic lattice, but in which only the tetrahedral interstices are occupied by hydrogen atoms. In group VA (V, Nb, Ta) the hydrogen-saturated metal attains a composition slightly below that of a monohydride under normal conditions. Finally the metals of group VIA (Cr, Mo, W) do not dissolve appreciable quantities of hydrogen. The manner in which hydrogen solubility disappears on alloying a group VA metal with one from group VIA has previously been investigated.2 It is necessary, in order to obtain a general picture of the reactions of alloys of the early transition metals with hydrogen, to examine a system containing metals from groups IVA and VA in which there must be a change from a fcc to a bee hydride phase. The system chosen for investigation was the pseudobinary system between titanium hydride and niobium hydride. Metallic alloys were prepared by melting iodide-prepared titanium with zone-refined niobium in an argon-atmosphere are-furnace. To ensure homogeneity each alloy was cold-swaged and then heated at 1250°C in a high-vacuum furnace until metallo-graphic examination confirmed its complete homogeneity. Small weighed specimens of the alloys were charged with hydrogen using gaseous hydrogen generated by heating titanium hydride. The apparatus has been described elsewhere.3 Throughout the charging process the hydrogen pressure was kept at about 1 atm while the specimen, initially at 800 °C, was slowly cooled to 150°C over a period of days. The total amount of hydrogen absorbed by each specimen and the room-temperature crystal structure of the hydride powders were determined. The X-ray investigation indicates that the fee hydride phase arises from alloys extending in composition from titanium to 67 at. pct Nb. After a two-phase field lying between 67 and 74 at. pct Nb in which the fee and bee hydrides coexist, all alloys richer in niobium yield a distorted bee hydride. Data derived from parameter measurements are presented in Fig. 1. The atomic volume per metal atom has been plotted against the composition of the initial metallic alloy in order to facilitate comparison of the effects of hydrogen addition in the two phases of different crystal structure. The amount of hydrogen absorbed by each alloy at saturation in terms of the hydrogen to metal ratio and alloy composition is given in Fig. 2. Over the whole range of the fee hydride phase the hydrogen content remains constant, while in the distorted body-centred hydride phase, the hydrogen content increases with increasing titanium content reaching a hydrogen/metal ratio of 1.4 at the boundary of the two-phase region. It seems likely, therefore, that the maximum hydrogen content of the fee hydrides is limited to a hydrogen/metal ratio of 2 because hydrogen atoms

Jan 1, 1962

By A. P. Woods, J. A. Elias, A. J. Heckler

A method is described by whichX-ray pole figures and axis density figures may be plotted automatically. The X-ray data are obtained using a Siemens texture gonionleter and the Schulz reflection method. Composite sampling methods are used to obtain a full quadrant of the pole figure. The contour lines of the pole figure and axis density figures are drawn using a computer-controlled x-y plotter. The computer program used to draw the contours was obtained from ZBM. POLE figures used to describe crystallographic orientations of poly crystalline sheet materials are usually plotted manually from X-ray diffraction output in the form of a strip chart recording of the intensity distribution of a given crystallographic pole in physical space. Today's computers and associated plotting equipment now make it possible to plot pole figures and axis density figures automatically. Inverse pole figures have been determined by mathematically "inverting" X-ray pole figure data.'-' In general, these methods require complicated, time-consuming numerical calculations. A more economical but less accurate method is to determine the axis densities of low-index crystallographic poles using an X-ray diffractometer. When these axis densities are plotted in a unit stereographic triangle contour lines can be drawn to represent the axis density distribution. This can now be done automatically. Computers were used to plot pole figures by a method developed by Holland, Engler, and powers.' In their method intensity ratios based on a random standard sample were obtained from a strip chart recording, and the stereographic (x, y) coordinates of these ratios were determined by a computer. Symbols characteristic of different intensity ratio levels were then plotted using an automatic x, y plotter and intensity contours were drawn manually. The present paper describes a method by which pole figures and axis density figures have been automatically plotted from digital data obtained from a Siemens X-ray unit. Plotting was accomplished using an IBM 1620 computer and a Calcomp 563 digital plotter. COMPUTER PROGRAM The computer program was obtained from IBM Systems Reference Library, No. 1620-CS-05X, and was designed to plot contour maps from randomly distributed data. It consists of a set of twelve separate subprograms, four of which were used in this work. The program takes a given distribution of data points and by a numerical method determines the values at mesh points of a square grid system superimposed over the input data. The output data from this program is in a form suitable for input to the contour plotting program. A smoothing program is also available which calculates new mesh point values from a continuous function fitted to neighboring mesh points. The degree of smoothing depends on the number of points around a given grid point which are used to adjust or smooth the grid value. The contour plotting program is designed to allow the user to specify the interval, scale, and annotation of the contours to be plotted. EXPERIMENTAL PROCEDURE Pole Figure Data Points. Diffracted X-ray intensities were determined using a Siemens texture goniometer and the schulzs reflection method. Due to geometric

Jan 1, 1968

VITRIOL is likewise a mineral substance from whose exhalation, according to the opinion of some, are generated and produced the elemental materials or substances which produce metals, particularly gold. It is not a fumosity from metal nor is it a thing from which metal is extracted in any manner, although it shows in certain ways that it is not entirely without metal since it produces a certain trace of it. It is a thing that has a great resemblance to alum; it has a biting substance, is sharp to the taste and pungent to the tongue, and has an astringent nature. It dissolves in water and every damp place in a short time. They say that the reason for this lies, as with every other mineral, in its poorly joined watery substances. Nor does this mean that it does not contain much earthiness; on the contrary it seems to me that there are in it five. [2.9v] different participating qualities, that is, the property of sulphur, the action of alum, the corrosion of niter or of salt, and from the metals, the properties of copper and of iron. Its ore is mined in the valleys of mountains in wild but not too rugged places. It is more a gray earth or soft dead rock than a hard stone. It always has in it some yellow and green spots or near it is some sulphur mineral, either large or small.. When it is beneath the earth it exhales a sharp and very strong foul odor of scorching similar to that of sulphur. And the waters that rise where it is are all foul, earthy, and thick, some boiling with great fumes and others without great fumes, so that they surely appear to be infernal products in many places where there is a large quantity of it. After you have excavated and sorted well the quantity you wish, the ore must be put in a heap in open airy places before the vitriol can be extracted from this soil or ore, however you wish to call it. And it is left thus exposed to the weathering of the rains, the cold, and the sun for five or six months. It must be turned several times in order to bring to the surface that which was underneath; and always when this is done it is broken small with the eye of a mattock so that it is better heated and baked throughout. When it has been brought to this point it is covered over by a shed built above it or it is carried under a hut that has already been made. Here it is left to stand for another six or eight months before it is worked.

Jan 1, 1942

By J. C. Uy, A. A. Burr

A quantitative relationship between the allotropic phase boundaries of zirconium-base binary systenzs and the solute metallic valence is shown through an intermediate thermodynamic parameter. A simplified equation relating this parameter to the phase boundaries is briefly reviewed, and data from the literature are used to show the relationship of this parameter to the solute metallic valence. It has been reported that the solute metallic valence can be used as an index of phase stabilization in zirconium-base binary alloys.' It was shown that the algebraic sign of the slopes of the hcp/bcc phase boundaries of zirconium alloys correspond to the algebraic sign of the metallic valence of zirconium minus the metallic valence of the solute, or, in other words, a solute whose metallic valence is higher than that of the solvent tends to stabilize the high-temperature phase while one whose metallic valence is lower than that of the solvent tends to stabilize the low-temperature phase. Further analysis of the zirconium binary systems has revealed a quantitative relationship between the solute metallic valence and the relative slopes of the two-phase allotropic boundaries. This relationship involves a thermodynamic quantity whose significance can be seen in the following section. PHASE-STABILIZATION PARAMETER Let Qb be the difference between the partial molar heats of mixing of a given solute in the two allotropic phases of the solvent which are in equilibrium with each other at a given temperature, thus A relationship between this term Qb and allotropic phase boundaries has been employed by several au-thors'-= in the evaluation of phase diagrams, and can be briefly derived as follows. Referring to Fig. 1, consider the general case of two allotropic phases, each having a small mole fraction (Xa,Xb) of the solute, in equilibrium at temperature T and atmospheric pressure as represented by the reaction. solute in ß phase =solute in a phase If now a reaction occurs such that an infinitesimal amount of the solute is removed from the ß phase and added to the a phase, there would be a partial molar

Jan 1, 1967

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.' Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By R. F. Stewart, A. W. Hall

A method has been developed for continuously measuring the moisture content of coal. The method is based on the thermalization of fast neutrons by hydrogen in the coal. Neutrons from a small radio-isotope source penetrate the coal, are scattered by hydrogen, and measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. In a pilot-scale system, moisture was measured continuously within 0.2% in coal moving at rates up to 20 tph. The method is adaptable in industry for continuously measuring the moisture content of coal at high tonnage flow rates. Such an application would permit continuous recording of moisture in coal without sampling and facilitate quality control. An automatic and continuous method of measuring the moisture content of coal is needed by the coal industry. Automatic control of the coal quality would reduce the cost of coal preparation, improve the product, and thus indirectly increase the use of coal. Moisture in coal can be determined by several methods, but the time required to obtain samples and analyze them by existing methods makes it difficult, if not impossible, to control the quality of the product. Both producers and consumers need a method for continuous and instantaneous measurement of moisture content without sampling in order to regulate process equipment and keep the moisture content of coal within specifications. At the Morgantown, W. Va., Coal Research Center we are developing a nuclear method for continuous measurement of moisture in coal. This method is based on the thermalization of fast neutrons by hydrogen in the water and organic matter of coal. Neutrons from a small radioisotope source penetrate the coal, are scattered by hydrogen, and are measured by a thermal neutron detector. The number of thermal neutrons counted can be directly correlated with the moisture content of coal. Design of a moisture meter based on neutron thermalization depends on many variables, any or all of which can affect the sensitivity of the meter. These factors include those related to the nuclear aspect; type and size of neutron flux and source, type of detecting device, and background count; and those related to the coal being tested: rank, particle size, and ash content. A survey was initiated to eliminate the relatively insignificant factors and to ascertain the magnitude of the major effects. Such information was necessary to fully evaluate the technique and to establish design criteria. Coal contains a relatively large amount of hydrogen in the organic coal substance and the water of hy-dration of the shaly material as well as in the moisture. To apply this concept of moisture measurement to coal requires that the organic substance in coal from any one seam of a particular mine be uniform in hydrogen content. The difference in total hydrogen content of wet and dry coal is relatively small, so that a moisture measurement based on this concept requires a measurement between two large numbers to a high degree of precision. Thus, it was necessary to develop a highly precise instrumentation system for continuous measurement and to obtain a physical arrangement permitting measurement of moving coal with a minimum effect from density variation. EXPERIMENT WITH TRAYS OF COAL Tests were conducted with metal trays containing SO to 100 lbs of coal to develop an instrument system of high precision. A scaling system with a maximum instrument error of 0.2% was used to test different types of thermal neutron detectors. The most suitable type of detector was a boron-10-lined proportional counter tube. While this type of detector showed satisfactory stability, extensive testing disclosed a long-term count reduction probably due to some type of deterioration in the detector. However, development of an electronic system using dual detectors eliminated this deterioration as a serious problem. (The second detector would be used to measure a reference drum of dry coal — the difference in count rate between the wet coal and dry reference coal being a direct measure of moisture content.) Table I, column 1, shows typical results with a 1-curie plutonium-beryllium neutron source and a thermal neutron detector beneath a tray of coal and illustrates the precision of measurement. Consecutive measurements (indicated in Table 1, columns 2-5) of thermal neutrons at various times and positions be-

Jan 1, 1968

By Geoffrey Purcell

Although the extractive metallurgist has not yet tackled the problem of getting blood out of a stone, he must, when faced with the mini- metal values of today's ores, believe that this ultimate miracle will soon be expected of him. Even assuming that some plausible professor at one of the few remaining minerals industry schools could persuade the National Science Foundation to sponsor such a sanguine research project, the funds might have to go begging for want of a graduate metallurgist. Falling enrollment in fields devoted to nonrenewable mineral resources, long a matter of grave concern to educators, is now recognized as a problem of great national consequence urgently needing a solution. While the law of supply and demand might eventually be expected to right the imbalance of engineers, time is not on our side and action to correct the shortage is required now.

Jan 1, 1970