Search Documents

By Rush Sill

THE processes of superficial alteration depend on physical conditions, environment, geologic history and chemical and mineralogical composition. Superficial alteration is confined particularly to the zone of shallow circulation, as this is the zone of solution; its rocks are open and the circulation within it is compara-tively rapid. The enrichment of ore deposits in this zone, therefore, is of special interest. The depth of the vadose, or zone of shallow circula-tion, is variable, because its lower limit depends on the variable level of ground water. In moist, hilly countries its depth varies from a few feet to several hundred feet. In arid regions where the rainfall is low and evaporation great, this zone may extend to much greater depths. Permeability of the deposits . is essential to the downward migration of metals. In rocks, that have been fractured since the primary ore was deposited, there is generally more extensive and deeper enrichment than in ore deposits that have been but slightly fractured. A warm climate increases chemical action and abundant rain fall is favorable to enrichment. Low relief and slow erosion give long periods of weathering and thorough leaching.

Jan 9, 1922

By Bernard York

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability.

Jan 7, 1953

By Gardner F. Williams

Chemically, the diamond is composed of the element carbon in its pure crystallized state. The diamond crystallizes in the isometric system, and the most common forms are the octahedron and dodecahedron, while the (24-sided) tetrahexa-hedron is not uncommon. Cube diamonds with beveled edges representing the combination 8 0 8 and 8 0 2 are occasionally found in the Bultfontein and Premier (Wesselton) mines at Kimberley, South Africa. The diamonds from various mines have distinctive forms of crystallization, or variations of the same forms, so characteristic that those familiar with South African diamond-mines and their products can determine positively from which mine any given parcel of diamonds has been obtained. It is not always possible to determine the source of each individual diamond, for similar stones are occasionally found in digerent mines; but these are exceptions to the rule. There is a difference in the luster, shape or crystalline form of the diamonds from the various mines that gives each mine some distinctive characteristic. In one mine nearly all of the crystals are sharp-edged octahedrons, while in another, dodecahedrons with rounded faces predominate. One might give no end of peculiarities of the diamonds from the various mines; but it will suffice for the purposes of this paper to state the fact that such distinctive characteristics do occur. From this observation it may be concluded that the diamonds in the mines of the Eimberley district, which occupies a small area (see Fig. I), did not have a common origin. The diamond is the most impenetrable of all known substances, and will scratch any other stone, or the hardest steel. It is a very strong reflector of light, and refracts incident rays more than any other substance except crocoite.l

Jan 1, 1905

By N. M. Raju, B. Singh

The paper seeks to present the results of experimentation in room and pillar stopes with different ground conditions to determine the safe working span. In the experimental stopes, ground movement was monitored with gradual widening of the room span. The field measurements included closure between the stope walls and the extent of ground movement in the hangwall using borehole extensometers. hock bolting was used as an exclusive support system which enabled introduction of scrapers for improving productivity. In one nine, phosphate bed, 3 to 3.5 m thick dipping at 45O and overlaid by weak laminated shale, was worked at shallow depth of cover. h the experimental panel, five s topes were worked with spans varying from 5.5 to 7 m. In the second mine, the chalcopyrite orebody up to 6 m in thickness dipping at 25 - 30" was worked at a depth of 1100 m. The hangwall consisted of fairly competent schistose rocks and therefore 10 to 15 m wide spans could be experimented. The field measurements confirmed that in the phosphate mine with weak shale roof, 7 m span could be safely worked with subsequent caving of the bolted roof. In the copper mine, 15 m span could be worked and the stopes required subsequent backfilling for better ground control.

Jan 1, 1983

By Kenneth Cottingham

The number of wells drilled in Ohio in 1943 was slightly in excess of the number drilled in 1942. Compared with the average annual completions for the five years preceding, the year 1943 was short 11 per cent, hut the average initial volume of gas wells was considerably improved. In 1942 the average initial open flow per gas well was 668 M cu. ft., whereas in 1943 the average was 913 M cu. ft. Although no large gas-producing areas were discovered during the year under review, some 30 small pools were found in 17 of the counties of eastern Ohio. These new pools averaged about 300 acres each, and most of them were not extensions but were separate pools adjacent to older production. The Clinton sand furnished most of these discoveries, although six were from the Berea, one was Newburg, and three were shallow sands. No discoveries were made outside former producing counties, and there was no new development the Trenton area of western Ohio. The number of oil wells decreased from 181 drilled in 1942, to 170 in the year 1943. The production of Pennsylvania-grade oil increased 7644 bbl. The total Corning production, however, decreased 91,325 bbl. The present price of Corning-grade oil, $1.31 per bbl., is too low, in the opinion of the operator, to justify exploration. Until something is done in correcting the price level of Corning grade, the production probably will continue to decline. The oil industry in Ohio is making a concentrated effort toward increased production and improved methods of recovering Pennsylvania-grade oil, and a.s this report is written a research and engineering program is being formulated for the benefit and information of the various producers of that grade in Ohio.

Jan 1, 1944

By Kenneth Cottingham

The number of wells drilled in Ohio in 1943 was slightly in excess of the number drilled in 1942. Compared with the average annual completions for the five years preceding, the year 1943 was short 11 per cent, hut the average initial volume of gas wells was considerably improved. In 1942 the average initial open flow per gas well was 668 M cu. ft., whereas in 1943 the average was 913 M cu. ft. Although no large gas-producing areas were discovered during the year under review, some 30 small pools were found in 17 of the counties of eastern Ohio. These new pools averaged about 300 acres each, and most of them were not extensions but were separate pools adjacent to older production. The Clinton sand furnished most of these discoveries, although six were from the Berea, one was Newburg, and three were shallow sands. No discoveries were made outside former producing counties, and there was no new development the Trenton area of western Ohio. The number of oil wells decreased from 181 drilled in 1942, to 170 in the year 1943. The production of Pennsylvania-grade oil increased 7644 bbl. The total Corning production, however, decreased 91,325 bbl. The present price of Corning-grade oil, $1.31 per bbl., is too low, in the opinion of the operator, to justify exploration. Until something is done in correcting the price level of Corning grade, the production probably will continue to decline. The oil industry in Ohio is making a concentrated effort toward increased production and improved methods of recovering Pennsylvania-grade oil, and a.s this report is written a research and engineering program is being formulated for the benefit and information of the various producers of that grade in Ohio.

Jan 1, 1944

By Frank E. Caropreso, William P. Badger

A hydrogen peroxide precipitate process has been adopted by Atlas Minerals for the recovery of uranium oxides from sodium chloride strip solutions. Adoption of the process was based on laboratory and plant tests comparing hydrogen peroxide with other precipitants. Plant operation has demonstrated that the hydrogen peroxide process consistently yields uranium concentrates of high purity and barrens of low uranium content. Increased U3O8 concentration in the product, reduced levels of impurities which incur penalties, and higher product density have produced economic advantages.

Jan 1, 1974

By F. M. Lewis, J. E. Goodman

A larger, slow-speed, under-loaded ball mill and hydraulic classifier have almost doubled grinding efficiency at the lsabella mill. TENNESSEE Copper Co. operates two ore con-A centrators, the London and Isabella mills near Copperhill, Tenn. In 1948 and 1949 the small ball mills and rake classifiers in the London concentrator were replaced by one large ball mill and one hydraulic classifier. This new ball mill was designed oversize so that it could be operated at slower than normal speed. The proper operating conditions were established and the results published.' Later it was found that this mill operated more efficiently with a small ball charge." While this London grinding practice was being developed, the Isabella grinding circuit was not changed in any way. It remained a conventional two-stage rod mill—ball mill combination, the rod mill in open circuit and the ball mill in closed circuit with a rake classifier. Study of the data indicated that grinding cost could be lowered by converting to the London practice, but not enough would have been saved to warrant the expense of converting. No plan for improving this grinding operation could be developed. In 1953 this study was reopened when plans were made to increase the Isabella mill output from 1150 to 1500 tpd. At this time the grinding circuit consisted of a 6x12 rod mill followed by a 6x12 ball mill in closed circuit with a 6-ft rake classifier. Another 6x12 ball mill and 6-ft rake classifier would have been sufficient equipment and would have been the simplest and cheapest installation. However, this would have offered no improvement in grinding efficiency or operating cost. If, on the other hand, the grinding operation could be converted to the London practice, by installation of one large 101/2x9x9 tricone mill and a 10-ft hydroscillator,2 lower operating costs would justify the additional investment. Economics: Table I presents estimates for the two schemes for enlarging the Isabella mill. In the first scheme, column 1, one 6x12 ball mill and one 6-ft rake classifier were to be added. In the second scheme, column 2, the existing small ball mill and rake classifier were to be retired and one large mill and hydroscillator were to be installed. Estimated savings from the difference in operating costs made an attractive return on the additional investment for the large mill and hydroscillator. Actual costs of carrying out this plan are tabulated in column 3b. It will be seen that these costs follow the estimates in column 3a very Closely. The return on the additional investment is calculated from the difference in the operating cost in column 1 and the actual operating cost in column 3b. This too come very close to the estimate. Power and Steel: Power requirements and steel consumption for the rod mills and ball mills, both actual and estimated, are presented in Table 11.

Jan 1, 1958

CURRENT MATTERS Page Page Colorado Meeting iii. Members in Military Service... xxxvi New York Meeting, Proceedings. iv Personal xxxix War Smoker xi Positions Vacant xli Woman's Auxiliary xxiii Engineers Available xli Meeting of Board of Directors... xxvii Forthcoming Meetings xlii Publication Notes xxviii Library xliii Local Section News: Membership xlvii Colorado xxix Biographical Notices: Montana xxx Arthur B. de Saulles lxxi Puget Sound xxxi James W. Malcolmson lxxii Tulsa xxxii Frank Firmstone lxxiii Affiliated Student Societies xxxii A. Stanley Hill lxxv Eleventh Engineers xxxiii Frederic W. Matthiessen lxxvi Enlistments in Engineer Organ- _ Institute Committees lxxviii izations xxxv Officers and Directors lxxxvi

Jan 4, 1918

By A. H. Dierker

Next to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry. Fundamental Considerations In a general way, molding sand in the average steel foundry passes through the cycle shown in Fig. 1. This diagram indicates that if all of the sand could be returned from the shakeout floor to the mixer no new sand would be required from the stock pile and molding costs would be reduced accordingly. Unfortunately, for reasons to be discussed later, it has heretofore been necessary to dilute the used sand constantly with new raw sand in order to maintain the properties that are essential to the production of satisfactory molds.

Jan 1, 1930

Oceanographers are tooling up. Back of the build-up is Navy defense work and private business. Business is dipping toes in the ocean gingerly and not sure whether the motivation is based on logic or intuition. The problem is that new business opportunities in the oceans could explode rather than evolve. The question is when. At stake for earthlings are food supplies, mineral resources, oil and gas, weather forecasting, navigational systems, shore erosion control and sewage disposal, as primary targets. "Twenty years ago, offshore oil seemed a remote possibility for economic exploitation but today it is a reality. It became a reality largely because of the development of practical ocean seismic equipment and drilling platforms. Today the oil industry is looking at submerged-type drilling rigs. Mineral exploration in the sea is more expensive than on land now primarily because familiar land tools are being modified for sub- marine work." These were the ideas expressed by C. G. Welling of Lockheed Missiles & Space Co., at one of the many meetings that have taken place so far this year on development of marine resources. Welling's views indicate the rationale of companies that have already invested in the sea. Many companies, including those in mining, have observers who caution, "go slow." The continental shelfs and even the deep ocean floor represent to the mineral industries the age-old, enigmatic confrontation-is this the time to move? To no other industry, except Defense, are the results of correct timing so vital.

Jan 8, 1967

By Samuel M. Dunaway

INTRODUCTION ASARCO Incorporated purchased the East Tennessee Zinc Mines of the American Zinc Company and commenced operating on November 29, 1971. Presently, three mines are operating producing 6620 t/d (7300 stpd). The ore mined is sphalerite which occurs In lower Ordovician carbonates of the upper Knox Group and occurs in open space and fracture filling. Orebodies range from 3 to 46 m (10 to 150 ft) thick with dips from flat to 20º. The mining method is random room and pillar modified by shrinkage and bench stoping. Like other mining departments, the mining group at the Tennessee Mines Division is constantly looking for methods to improve productivity and safety and to reduce mining costs. This involves testing new equipment, trying new ore extraction ideas and making mining plant alterations to meet changes in operating conditions. The areas of change that will be described in this paper are longhole raising, jumbos and LHD loading, shaft sinking, conveyor transport of ore and sublevel haulage developments. LONGHOLED RAISES Raise driving has always been a hazardous occupation for miners and today it is becoming more difficult to get competent people for this kind of work. This problem has led us to seek an easier, safer way in which to excavate raises. The first longhole raises were excavated in the early 1970's using a Gardner-Denver air trac equipped with a PR-123 rock drill. The machine used 38 mm x 244 cm (1 ½ in x 8 ft) round rods with rope

Jan 1, 1977

By A. B. Young

THERE were produced in this country in 1923 probably in the neighborhood of 12,000 or 13,000 tons of refined and crude arsenic, by far the greater portion coming as a by product of smelting operations. Early this year copper smelters were producing arsenic at the rate of about 425 tons per month and lead smelters at the rate of 7;0 tons per month. During the entire eighteen years prior to 1919, there were produced in the United States only 47,000 tons of arsenic, which amounts to only 25 per cent. of the present output. The great increased demand has come about through the augmented use of arsenates as insecticides and arsenates as weed killers. In an extract from "Mineral Resources of the United States" on "Arsenic in 1922," Messrs. Heikes and Loughlin say, "The minimum possible demand for arsenic in 1923 was estimated at the end of 1922 to be about 13,000 tons, including 2000 tons for plate glass manufacturers, 3000 tons for lead arsenate, 3500 tons for calcium arsenate, 1500 tons for weed killers, 1200 tons for Paris green, 1000 tons for sheep dips and 750 tons for proprietary mixtures. More recent information, however, indicates twice as great a demand for calcium arsenate." The latter has found great use in the last three or four years as a weapon to combat the boll weevil pest of the southern cotton belt. ~t the present writing refined white arsenic is being quoted on the New York market at from 13)d c. to 1455 c. per Ib., while the average price during the eighteen-year period just mentioned was 4.8 c.

Jan 1, 1924

By Frank Firmstone

By Marvin Lee

Kansas retained, for the eighth consecutive year, the fourth position in the list of oil-producing states. The total crude-oil production during 1934, as reported by purchasers to the State Corporation Commission, was 45,538,564 bbl. on 97 per cent tank table calculations of the purchasers, or 46,946,973 bbl. as carried on 100 per cent measurement in U.S. Government reports. The corresponding figures for 1933 are 40,008,940 and 41,236,021, respectively. The increase of production over 1933 was due to the rising demand for oil from Kansas, caused principally by three factors: the continued regulation of the producing branch of the industry by Federal and State authorities, which had the effect of reducing illegal production that has been so destructively competitive with Kansas crude and refined products; the normal decline of production in other areas; and, last and best, general increased demand of the public for petroleum products. The price level remained unchanged for the first time in oil history for so long a period. Kansas 36" gravity crude remained at $1 per barrel from September, 1933, and throughout 1934. Price stability and the confidence in the regulation of production to meet the consumer demand, which is increasing, brought greatly renewed interest in Kansas fields. Drilling activity has been largely in the western part of the state where expiration of leases, on large blocks of acreage, assembled before the depression, is forcing either action or loss of the lease investment carried for a long period. The drilling of these many blocks of acreage, previously assembled on geologic information, has caused the opening of more fields than during any previous year of Kansas oil history and is proceeding faster than anticipated a year ago. Interest grows within a successful enterprise, and the momentum caused by the successes of 1934 will continue in 1935 unless unusual conditions arise and end the apparently good opportunity for financial return. Geological exploration methods used in new field discoveries are shown in the tabulation of new discoveries (Table 3).

Jan 1, 1935

By M. Allingham

This paper examines the contribution which econometric methods may be expected to make to the specification of commodity agreements, and how in turn computer methods may help in this. Starting from the specification of a model, the paper examines four activities: estimation of the unknown parameters; analysis of the properties of the model; simulation experiments with the model; and control of the model. In each of these activities the basic methodology is outlined, and the contribution of computer methods assessed.

Jan 1, 1977

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By Allen Rogers

IT IS universal practice for corporations, at the end of the fiscal period, to call in a firm of chartered accountants to audit the books. The effect of this is to put an independent organization's seal of approval on the accounting of the business done by the management. Their report lets the stockholders know that the accounts rendered truly present the results of the year's business. This is as it should be; the average stockholder has no personal contact or even acquaintance with the managers of his enterprise and the approval of their stewardship by an indepen-dent agent is very desirable for maintaining confidence in their honesty and ability. But such an examination deals only with what may be called the arithmetic of the business; even the most elaborate audit, as the practice is at present, goes no further than to verify the items of the inventory. In other words, while checking up the entries showing the transaction's of the year and certifying to the correct-ness of the items of the balance sheet, such a report gives the stockholder no idea of the ability with which his affairs have been managed. If the profit and loss balance is satisfactory, as certified by the public accountants, he assumes that the management has been able; where it is not, he turns to the president's report and usually finds an explanation. Such an explanation never takes the form of admission of mis-takes in business judgment or of bad technical manage-ment. It could hardly be expected that it would. The stockholder is generally furnished, therefore, with a certificate of the honesty of his management, but never one of its ability. He does not worry about the latter as long as dividends come in; when they cease, his action generally finds expression in replacing the management. In other words, so long as profits are realized, he assumes the management to be good, even though its success is a matter beyond its control and better management would make larger profits. When there is no profit, the stockholders have no means of knowing whether it is due to conditions beyond the control of the management, as the annual report is sure to allege, or whether, by better management, profit is possible. Here is where the technical audit comes in.

Jan 6, 1922

By Alexander L. Holley

A CHARACTERISTIC, and, to Americans, an amusing discussion of the three-high rail-mill, arose out of the reading of Mr. Lauth's paper on three-high plate-mills, at the Glasgow meeting of the Iron and Steel Institute. From the report of the meeting in the English papers, it appears that Mr. Menelaus, the celebrated rail-maker of Dowlais, could not wait for the discussion of Lauth's plate-mill, but launched at once into the British objections to the three-high rail-mill, which is quite another matter. The American mill, which is very different in principle and ar288

Your outgoing President, following the worthy example of distinguished predecessors, submits a reckoning of his stewardship. He renders this fully realizing that without the hearty cooperation of Directors and Secretary, which he here recognizes most cordially, no President, who at best is but a passing force, can achieve markworthy results. The details as to your membership, finances, intellectual output, and,-other activities, have been submitted in the report of the Secretary.* It is enough to emphasize that during the year just expired, your organization has held two of its most successful meetings-one the largest in its history-has produced the largest number of papers, eliciting most interested discussions, has enjoyed its greatest income; and has received more than one thousand new members-passing the best previous record by more than one hundred, and exceeding the average increment of the, past five years by one third. It closes the year with 6528 members, the largest enrollment in its history. All of this might be true and yet the intellectual and social spirit, the loyalty of membership, the real life of the organization, might remain stagnant. As to these, it is for others than your speaker to testify. No comparison is feared.

Jan 3, 1918