Search Documents

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

By E. N. Cameron

GRAPHITE has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey.' The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs. The amount of graphite required by American industry is not large. Ordinarily only a few thousand tons of strategic grades are consumed annually, yet the elimination of this small tonnage would have serious effects in several industries. Strategic Graphite: Since World War I, 60 to 100 pct of the country's annual supply of graphite has been furnished from imports. At present, natural amorphous graphite for use in pencils and batteries is produced largely from American-owned mines in Mexico. Graphite for foundry facings is obtained from a number of sources. Neither grade is a serious problem. High purity graphite for carbon brushes and for pencil leads, however, is imported, largely from Ceylon, in the form of amorphous lump graphite. Most of the flake graphite used for crucibles and related refractory articles is likewise imported, largely from Madagascar, and much of the lubricant and packing grade graphite used by industry is obtained from the same source. The strateg'ic grades of graphite are therefore amorphous lump of the Ceylon type, crucible flake, and flake suitable for lubricants and packing. Ceylon lump and Madagascar flake have for many years been accepted as standard by domestic consumers of graphite, and various essential manufacturing processes are geared to the use of graphite from these sources. Ceylon graphite as marketed is classified into several grades based on particle size and purity. Processing methods are said to be simple, but the products marketed are carefully graded and are consistent in their characteristics, an important matter to the consumer. Nearly all the graphite produced in Ceylon is from veins. Resources are reported to be large, labor is cheap, production costs are low, and world competition is slight—factors accounting for the commercial success of the graphite mining industry in Ceylon. Madagascar is reported to have deposits of the Ceylon type, but its output consists almost entirely of flake. Madagascar graphite as received in the U. S. is further processed by importing organizations, and a large number of grades are produced to meet industry requirements, especially those for crucible flake and for lubricant and packing grade flake. Madagascar crucible flake as marketed is noted for coarseness, uniformity, toughness, clean-

Jan 1, 1957

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack. These products are of great potential value in many branches of industry as insulation materials, aggregates, fillers, abrasives, and additives. By proper selection of the perlite rock type and control of processing conditions, expanded perlite of a bulk density varying from about 2 to 20 Ib per cu ft can be • made. The physical properties of the particles comprising a product of a given bulk density also may be varied within wide limits of porosity, water absorption, and crushing strength. In general, crushing strength of expanded perlite increases in direct relation to increase in bulk density, but insulating value varies in inverse ratio to bulk density. The selection of a particular grade of expanded perlite for a given use as an aggregate is therefore always a compromise between insulating value, lightness, and friability. If porosity and water absorption are factors affecting the use of the material, factors other than bulk density are important. Some types of perlite rock tend to decrepitate excessively during expansion, resulting in a highly porous or even hygroscopic product of high friability relative to the bulk density of material produced. In general, treatment of any good perlite rock below the temperature necessary for maximum expansion, or insufficient time in the hot zone of the furnace for effective heat penetration to the core of the rock particles will result in some decrepitation and high porosity in the expanded product. On the other hand, exposure of the material to the temperature required for optimum expansion for a period of time slightly longer than that necessary for proper heat absorption will result in a slightly heavier product of extremely low porosity, i. e., a glazed surface. It is beyond the scope of this paper to describe in detail the rock types and processing methods used to produce the many types of expanded perlite in present use, or that may be produced to fill the present and future needs of industry. A few phases of the economics involved in processing and selling products made from this abundant and cheap mineral raw material, plentifully distributed in large and relatively accessible deposits in most western states and in other areas within economic shipping distance of large centers of consumption, will be treated with particular reference to the Los Angeles area. Relation of Balk Density to Use and Cost of Production Perlite differs from most other lightweight aggregates and fillers in that the raw material (perlite rock) may be quarried much as rock arid sand is mined, and then shipped into consuming areas as crude rock in open gondola cars at correspondingly low freight rates and handling costs. At processing plants in or near large consuming areas the rock is converted into relatively fragile, very bulky products which in most cases are used within a short haul of the processing plant or enter into a manufactured product made at the site of the perlite processing plant.

Jan 1, 1950

By M. R. J. Wyllie, F. Morgan, P. F. Fulton

The importance of formation factor, F, not only in electric logging but as a fundamental rock parameter has recently been stressed.',: The desirability of investigating the range of variation of the resistivity index exponent, n, in the relationship I = S ;", where I is the resistivity index and Sw the water saturation as a fraction of the void volume of a porous medium, has also been urged.3 The magnitude and variation of n with saturation and rock texture is a subject not only of theoretical interest but also one of prime importance in the interpretation of electric logs. A simple technique has recently been developed which enables both F and u to he measured with high accuracy and which may also find acceptance as a convenient method for the determination of irreducible saturation attainment in the restored state method of core analysis. Experience has taught that reproducible measurements of F are possible only if the resistance measuring electrodes are so arranged with respect to a plane face on a porous medium that they are able to make electrical contact with substantially all entry pores in that plane. In practice this may be achieved by using a platinized-platinum gauze electrode backed by some absorbent material (such as felt) which has been saturated with a fluid identical with that used to saturate the porous medium. Applicatiorl of pressure to the electrode and absorbent material then forces the gauze against the plane face of the porous medium and simultaneously squeezes saline solution through the meshes of the gauze. By this means the electrode is in continuous aqueous contact with all pores and satisfactory and reproducible low resistance contact with the porous medium is achieved. Clearly this method, although satisfactory for measurements of F, cannot be applied to the making of continuous resistance measurements on a porous medium while capillary pressure desaturation is being carried out. However, accepting the principle that for satisfactory results electrical contact must be made between a measuring electrode and all pores adja- cent to that electrude, methods of bringing electrodes into intimate contact with the surfaces of porous media were investigated. Two methods were ultimately found to be satisfactory: in the one, the metal electrode is formed on the required portion of the porous medium by the use of a metal spray gun, while in the second the electrode is painted on with an ordinary camel's hair brush. The first method has the advantage of permitting the use of any metal which can be sprayed, but has the disadvantage of requiring rather elaborate and expensive equipment. The second method is presently limited to silver electrodes although in principle other metals, e.g. platinum or gold, could be used. Moreover, the method is so simple and cheap, and has been found to be so satisfactory that it will be described in some detail. The core being investigated is cut into a right circular cylinder and is extracted and dried in the usual manner. The ends are then lightly painted with silver conducting paint* of the type used in printed electrical circuits. The quantity of paint used is not critical but the recommended, minimum compatible with entirely coating the core ends is recommended, particularly on the end that contacts the barrier. The core is then dried at atmospheric temperature for one hour or for shorter periods at any suitable elevated temperature up to about 110°C. It will be found that silver coatings so prepared are not only strongly adherent but also permeable and the core may be the core may be desaturated by the ordinary capillary pressure technique through one of the coated faces. The same permeability is characteristic also of thin metal coatings formed using the spray-gun technique. An ordinary Lucite capillary pressure desaturation cell has been adapted to a form suitable for measuring the resistivity of the saturated silver faced cores both at 100 per cent saturation (i.e., F) and at intermediate saturations down to the irreducible minimum. This has been achieved as follows: A Coors porcelain barrier, having a displacement pressure of c 30 psi was grooved across a diameter. Dimensions of this groove were c 1 mm deep and 1 mm wide at the top. The groove was then painted thickly with silver conducting paint, the paint in the groove being extended lightly over the edges of the groove for a distance of c 1 mm on each side. A 30 gauge silver wire was then arranged in the groove in a form of a spring bow, each end of the silver being held at diamet~ically opposite ends of the groove by means of plastic cement. The arc of the bow at its highest point was arranged to be a millimeter or so above the face of the barrier, while one end of the bow wire was led by means of a pressure-tight connection through the wall of the capillary pressure cell. The groove in the barrier was then Surrounded by suitably cut portions of Kleenex in the conventional manner so as to ensure capillary continuity from core to barrier, and the core placed on the barrier. The weight of the core distorted the silver spring bow and good electrical contact was thereby made between the outside of the cell and the lower painted silver electrode. Electrical connection to tile top painted silver

Jan 1, 1951

By M. R. J. Wyllie, F. Morgan, P. F. Fulton

The importance of formation factor, F, not only in electric logging but as a fundamental rock parameter has recently been stressed.',: The desirability of investigating the range of variation of the resistivity index exponent, n, in the relationship I = S ;", where I is the resistivity index and Sw the water saturation as a fraction of the void volume of a porous medium, has also been urged.3 The magnitude and variation of n with saturation and rock texture is a subject not only of theoretical interest but also one of prime importance in the interpretation of electric logs. A simple technique has recently been developed which enables both F and u to he measured with high accuracy and which may also find acceptance as a convenient method for the determination of irreducible saturation attainment in the restored state method of core analysis. Experience has taught that reproducible measurements of F are possible only if the resistance measuring electrodes are so arranged with respect to a plane face on a porous medium that they are able to make electrical contact with substantially all entry pores in that plane. In practice this may be achieved by using a platinized-platinum gauze electrode backed by some absorbent material (such as felt) which has been saturated with a fluid identical with that used to saturate the porous medium. Applicatiorl of pressure to the electrode and absorbent material then forces the gauze against the plane face of the porous medium and simultaneously squeezes saline solution through the meshes of the gauze. By this means the electrode is in continuous aqueous contact with all pores and satisfactory and reproducible low resistance contact with the porous medium is achieved. Clearly this method, although satisfactory for measurements of F, cannot be applied to the making of continuous resistance measurements on a porous medium while capillary pressure desaturation is being carried out. However, accepting the principle that for satisfactory results electrical contact must be made between a measuring electrode and all pores adja- cent to that electrude, methods of bringing electrodes into intimate contact with the surfaces of porous media were investigated. Two methods were ultimately found to be satisfactory: in the one, the metal electrode is formed on the required portion of the porous medium by the use of a metal spray gun, while in the second the electrode is painted on with an ordinary camel's hair brush. The first method has the advantage of permitting the use of any metal which can be sprayed, but has the disadvantage of requiring rather elaborate and expensive equipment. The second method is presently limited to silver electrodes although in principle other metals, e.g. platinum or gold, could be used. Moreover, the method is so simple and cheap, and has been found to be so satisfactory that it will be described in some detail. The core being investigated is cut into a right circular cylinder and is extracted and dried in the usual manner. The ends are then lightly painted with silver conducting paint* of the type used in printed electrical circuits. The quantity of paint used is not critical but the recommended, minimum compatible with entirely coating the core ends is recommended, particularly on the end that contacts the barrier. The core is then dried at atmospheric temperature for one hour or for shorter periods at any suitable elevated temperature up to about 110°C. It will be found that silver coatings so prepared are not only strongly adherent but also permeable and the core may be the core may be desaturated by the ordinary capillary pressure technique through one of the coated faces. The same permeability is characteristic also of thin metal coatings formed using the spray-gun technique. An ordinary Lucite capillary pressure desaturation cell has been adapted to a form suitable for measuring the resistivity of the saturated silver faced cores both at 100 per cent saturation (i.e., F) and at intermediate saturations down to the irreducible minimum. This has been achieved as follows: A Coors porcelain barrier, having a displacement pressure of c 30 psi was grooved across a diameter. Dimensions of this groove were c 1 mm deep and 1 mm wide at the top. The groove was then painted thickly with silver conducting paint, the paint in the groove being extended lightly over the edges of the groove for a distance of c 1 mm on each side. A 30 gauge silver wire was then arranged in the groove in a form of a spring bow, each end of the silver being held at diamet~ically opposite ends of the groove by means of plastic cement. The arc of the bow at its highest point was arranged to be a millimeter or so above the face of the barrier, while one end of the bow wire was led by means of a pressure-tight connection through the wall of the capillary pressure cell. The groove in the barrier was then Surrounded by suitably cut portions of Kleenex in the conventional manner so as to ensure capillary continuity from core to barrier, and the core placed on the barrier. The weight of the core distorted the silver spring bow and good electrical contact was thereby made between the outside of the cell and the lower painted silver electrode. Electrical connection to tile top painted silver

Jan 1, 1951

By C. S. Finney, John Mitchell

The decline of the beehive coking industry was inevitable, but it had filled the needs and economy of its day. A beehive plant required neither large capital investment to construct nor an elaborate and expensive organization to run. The ovens were built near mines from which large quantities of easily-won coking coal of excellent quality could be taken, and handling and preparation costs were thus at a minimum. The beehive process undoubtedly produced fine metallurgical coke, and low yields were considered to be the price that had to be paid for a superior product. Few could have foreseen that the time would come when lack of satisfactory coking coal would force most of the beehive plants in the Connellsville district, for example, to stay idle; and if there were those like Belden who cried out against the enormous waste which was leading to exhaustion of the country's best coking coals, there were many more to whom conservation was almost the negation of what has since become popularly known as the spirit of free enterprise. As for the recovery of such by-products as tar, light oil, and ammonia compounds, throughout much of the beehive era there was little economic incentive to move away from a tried and trusted carbonization method simply to produce materials for which no great market existed anyway. With the twentieth century came changes that were to bring an end to the predominance of beehive coking. Large new steel-producing corporations were formed whose operations were integrated to include not only the making and marketing of iron or steel but also the mining of coal and ore from their own properties, the quarrying of their own limestone and dolomite, and the production of coke at or near their blast furnaces. As the steel industry expanded so did the geographic center of production move westward. By 1893 it had moved from east-central to western Pennsylvania, and by 1923 was located to the north and center of Ohio. This western movement led, of course, to the utilization of the poorer quality coking coals of Illinois, Indiana and Ohio. These coals could not be carbonized to produce an acceptable metallurgical coke in the beehive oven, but could be so treated in the by-product oven. By World War I the technological and economic limitations of the beehive oven as a coke producer were being widely recognized. After the war the number of beehive ovens in existence dropped steadily to a low of 10,816 in 1938, in which year the industry produced only some 800,000 tons of coke out of a total US production of 32.5 million tons. The demands of the second World War led to the rehabilitation of many ovens which had not been used for years, and in 1941, for the first time since 1929, beehive ovens produced more than 10 pet of the country's total coke output. Production fell off again after 1945, but the war in Korea made it necessary once more to utilize all available carbonizing capacity so that by 1951 there were 20,458 ovens with an annual coke capacity of 13.9 million tons in existence. Since that time the iron and steel industry has expanded and modernized its by-product coking facilities, and by the end of 1958 only 64 pet of the 8682 beehive ovens still left were capable of being operated. Because beehive ovens are cheap and easy to build and can be closed down and started up with no great damage to brickwork or refractory, it is likely that they will always have a place, albeit a minor one, in the coking industry. The future role of the beehive oven would seem to be precisely that predicted forty years ago by R. S. McBride of the US Geological Survey. Writing with considerable prescience, McBride declared: "A by-product coke-oven plant requires an elaborate organization and a large investment per unit of coke produced per day. Operators of such plants cannot afford to close them down and start them up with every minor change in market conditions. It is not altogether a question whether beehive coke or by-product coke can be produced at a lower price at any particular time. Often by-product coke will be produced and sold at less than cost simply in order to maintain an organization and give some measure of financial return upon the large investment, which would otherwise

Jan 1, 1961

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936

By J. H. Nead, J. W. Halley

The new low-alloy high-strength steels are obviously here to stay. With 75 per cent higher yield strength and 50 per cent higher tensile strength than plain carbon structural steel, they permit 20 to 40 per cent weight savings and 10 per cent or more increase in pay load in the construction of railroad cars, buses, trucks, and a great variety of material-handling equipment. Their cost is low enough so that the extra cost of the new lighter construction over that with carbon steel offers an attractive self-liquidating investment; in some instances new construction with these low-alloy steels may even be as cheap as with plain carbon steel. A considerable and rapidly growing demand for the low-alloy steels has already sprung up. The many steel compositions that have appeared on the market lately18, 27, 28, 29, 30 to meet this demand would seem to indicate that no single composition is uniquely fitted for the purpose. However, no doubt some compositions are more suitable than others. The purpose of this study was, therefore, to compare the effects of the various alloying elements that might be used in the low-alloy steels in order to choose the metallurgically most logical composition, paying due regard, of course, to the economic aspects involved. Properties Desired in Low-alloy Steel A distinction between the new low-alloy steels and the common alloy steels is that the latter are generally used in the heat-treated (that is, quenched and tempered) conditions, whereas the new low-alloy steels are not only not heat-treated but are not susceptible to heat-treatment in the ordinary sense of the term. In this lies one of their chief advantages. Their properties can be obtained in the as-rolled, air-cooled, or annealed condition, just as with mild plain carbon structural steel. There is no need for heat-treating. Such steels can be readily formed hot or cold, and their properties are not appreciably changed by hot

Jan 1, 1936

By L. F. Terry, H. K. Ihrig, D. J. Sabin, Ralph E. Davis

This paper presents the results of a study of the comparative values of the several fuels commonly used by industrial plants. It shows that the energy actually recovered from any fuel and turned into useful work is dependent upon several factors: (1) the total energy available in the fuel, (2) energy losses resulting from combustion reactions and (3) energy losses dependent upon the mechanics of the firing operation. The chemistry of combustion and the losses resulting therefrom are discussed. The Advantages and disadvantages of the several mechanical methods of firing and the resulting heat losses in each are developed. Data obtained from several typical fuel operations, where careful records have been maintained, are presented to show that the practical results in the actual operation are in harmony with the theoretical results developed in the earlier part of this paper. Water power and solid, liquid or gaseous fuels are at present the only commercial sources of energy. The economic utilization of any one of them depends, in the final analysis, on the cost of energy per unit of finished product to which the energy is applied. The location of the plant utilizing the particular fuel chosen is a large factor in the original choice. The cost per unit at its original natural source, or even in its delivered form, is not always the final measure of its worth. The use of electricity as a source of energy illustrates this to the extreme. Electric current produced from water power is very cheap in certain localities. In Norway, current is sold as low as ½0# per kw-hr., while in dry cells it costs as much as $10 per kw-hr. Yet the sale of dry cells is a large business. The selling price of gas also varies widely. In some localities natural gas for the manufacture of carbon black sells for as low as $0.02 per million British thermal units, while artificial gas for domestic purposes sells for as high as $6 per million B.t.u. Obviously the cost per unit of energy is not the final determining factor in its purchase. Any discussion of the economic utilization of fuels must include costs in relation to the units of finished material manufactured. In large central power generating stations, this is the over-all cost per kilowatt-hour, and in ceramic firing the cost per unit of finished product of a certain quality is the criterion of economic utilization.

Jan 1, 1931

Discussion of the paper of W. C. PHALEN, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2249 to 2265. DAVID T. DAY, Washington, D. C.-Consider the United States broadly and the distribution of the salt industry. Think of the old solar-evaporation process up in New York State, then of the more recent processes in Michigan and Kansas and Louisiana, where the rock salt furnishes a large industry, then of the solar-evaporation process at Salt Lake, then turn to the crucial place in the United States, where there is an embarrassment of salt, and that is California. I am not forgetting' the immense body of salt east of that in the Virgin River country of Utah; but in California the situation is interesting. There are very large quantities of salt in the Searles Marsh region; again, in Southern California, at the southern end of Death Valley, there are two or three mountains of salt which have been explored recently, where the salt is sufficiently pure to be used at once. There is also a large deposit of gypsum, and it would be possible there, by extremely cheap means, to produce an amount of salt sufficient to furnish the United States' greatest needs. The principal reason that capital has been deterred from developing such a large mass is not the fact that solar evaporation produces a great deal of salt around San Francisco, but the fact that if potash salt is to be produced in connection with the salt in the borax region a, great deal of ordinary salt must be disposed of. It cannot be dumped, for it would get back into the brine again; the first rains would bring that salt back into solution again. It must be sold, given away, or hauled to a distance, which would mean a considerable freight charge. The salt will be going begging. E. G. SPILSBURY, New York, N. Y.-The remark of Dr. Day's regarding the likelihood of the production of a large amount of waste salt brings to my mind the condition that obtains in Germany in all of the potash fields. In Germany salt is a government monopoly. In the development of the potash deposits, it becomes a grave question as to how much salt they may be allowed to extract and bring to the surface.

Jan 4, 1915

By Rudolf Bernhard

STATIC soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the appli-cation of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the practical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes.

Jan 1, 1938

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By R. S. Handy

Does hand-sorting of mill feed pay? The fact that the practice is so general would seem to indicate that there must be good reasons for following it; yet, to my mind, the advantage in many cases is doubtful enough to invite a thorough discussion of the subject, in an effort to determine under what conditions hand-sorting does pay. A typical sorting plant in the Cœur d'Alene district handles about 800 tons of mine-run ore per day. The material is run over a grizzly with about 4-in. opening; the oversize is crushed to about 4-in. size and joins the undersize, and the whole product is washed and screened on trommels with about 11/2-in. openings. The oversize from these trommels is spread on a belt and the waste and first-class ore are sorted out by hand, the residue being further crushed, and passes, together with the trommel undersize, into the mill feed bins. About 50 tons of shipping ore and 150 tons of waste are sorted out per day, leaving about 600 tons of mill feed. To sort out this material requires 20 ore sorters and five bosses and repairmen. The normal cost of hand-sorting is about 16 c. per ton of run-of-mine ore, or 65 c. per ton of material sorted out. I believe that straight crushing and milling of the run-of-mine ore, in this case, is not only cheaper, but is metallurgi-cally more economical and efficient than hand-sorting followed by milling of the residue. At one of the Bunker Hill rock-houses, 1250 tons of run-of-mine ore are reduced to pass 30-mm., or about 11/4-in., opening in six hours, requiring five men. The equipment and the power consumed are not greatly different from that required in a sorting plant of the same capacity, and the normal cost of thus preparing the feed for milling is under 3 c. per ton of mine product. The relative cheapness of this method as against hand-sorting is thus clearly established, the saving being about 13 c. per ton. If there is any virtue in, hand-sorting, then, it must lie in the metallurgical results achieved. Possibly the favor that hand-sorting has found is due to a misconception as to what happens to the clean shipping ore if it is sent to the mill. If a mill makes, say, an 80 per cent. recovery on its feed, the hand-sorting advocate may assume that if the hand-sorted product be sent to the mill, 20 per cent. of the metals contained in it will be lost. This, I believe,

Jan 1, 1920

By Carl S. Westerberg

1,. C. McCABE*-—An increased derliand for coal in the west is to be expected because of the growth in population and industry during the past ten years. The author calls attention to the increased mechanical cleaning of Utah coal between 1938, when no cleaning was being done, and 194.7, when more than 24 pct of the production was cleaned. This is essentially the Period of most rapid growth of the Pacific Coast. area altliough the growth and, no doubt, the general trends in coal production and cleaning continued at a less accelerated rate during 1948. The Pacific southwest increased 37 pct in population between 1940 and 191.7 while the United States showed only a 7 pct increase in the same period. it has been estimated that there will be an additional 15 pct increase in population between 1947 and 1950. The conclusion that more coal and more mechanicak cleaning capacity will be required appears to be well founded. Mr. Westerberg discusses the cco- nomic advantages of coal cleaning reflected in freight savings, in lower cost per million Btu, and lowered ash and sulphur content. In view of the limited occurrence of coking coals in the west it would be interesting to know whether significant beneficiation in coking strength can be expected from mechanical cleaning of Utah coals. This has been demonstrated for some eastern and midwestern coals. One can readily agree to the desirability of recovering the fine coal that has heretofore been lost in washery slurry. The very cheapness of coal has Iridered

Jan 1, 1950

By J. A. Thompson, M. A. Mayers

IN recent years, the problem of damage to coke-oven walls by expanding coal charges undergoing carbonization has engaged great attention on the part of research workers in this field, and has led to the development of many devices for estimating these pressures.1-14 Only in Russell's method11 and in the Koppers ovens7 are conditions quite similar to those in commercial ovens. Tests even in these ovens are empirical because no information has been published to permit an evaluation of "scale effects." Owing to the relatively large wall area in these test ovens, the average wall pressure determined may be lower than that existing in localized areas. This factor may be compensated for in part by the testing of coal charged into the test oven at a bulk density that is as high as the highest that is believed to exist in commercial ovens. Both of these lacks might be filled by the development of an adequate gauge for the direct measurement of wall pressure exerted by the charge in commercial coke ovens in normal operation. Previous attempts to elaborate such instruments7,15 have resulted in units which, because they had to be water-cooled, probably produced changes in the conditions of carbonization, and which had to be removed from the oven before carbonization was complete, to avoid their destruction. Late in 1941 the Coal Research Laboratory undertook to develop such a gauge, in which gas pressure was balanced against the charge pressure and which thus would not require water cooling, on a suggestion made in 1937 by one of the present authors and William B. Warren, a former member of the Laboratory staff. The gauge heads themselves were to be simple and cheap enough so that they might be discarded after each run if seriously damaged. This would permit them to be left in place throughout the carbonizing period, when they could be pushed out with the coke. The basis of the design, of which the latest exemplification is shown in Fig. I, was that as the internal gas pressure within a flexible metal envelope was increased, the flexible wall would move away from a stop when the gas pressure just overbalanced the charge pressure. If the stop were an insulated electrical contact, the point of balance could be indicated by the breaking of an electric circuit. It was anticipated that, while the instrument must operate at high temperature, the presence of a strongly reducing atmosphere throughout the carbonizing period would so reduce-the danger of scaling that mild steel could be used for the gauge. This expectation has been justified. Danger of attack on silica oven walls by the steel gauge body can be eliminated by cementing asbestos paper or an alundum or silica plate to the back of the gauge body. The gauge head itself has a relatively heavy mild-steel body, A, into which standard ¼ in. pipe B is screwed to conduct gas and electrical leads. The body is closed by a single bellows C. consisting of two annuli of 0.011-in. (0.28-mm.) cold-rolled shim-steel spot-welded together at their outside edges. The lower one is

Jan 1, 1944

By H. E. Mills

THE local auditorium of a little Alabama mining town was crowded with expectant men, women and children, as the bulletin board had announced the addition of visiting entertainers to supplement the local talent and motion pictures which usually made up the program of the regular monthly safety meeting. In the audience, near the stage, sat a group of bright-faced boys in boy scout uniforms, discussing the picture just completed. As the lights flashed on a crash and scream was heard from the outside, a shrill whistle and word of command from the scoutmaster, and five of the scouts ran out of the hall, while the mine super-intendent stepped on the stage and requested everyone to keep their seats. The scouts returned, three of them carrying a limp figure in their arms, while the other two cleared the doorway and aisle of excited spectators. They marched to the stage and, placing the apparently badly-injured boy on the floor, proceeded to give an expert demonstration of first aid to the injured. The scoutmaster then explained to the audience that the whole affair had been arranged for their benefit, and invited the local first-aid men to come up on the stage to examine and criticize the boys' work. This gave an opening for several talks on the value of first-aid training and accident prevention, which is the main object of the monthly meetings. This demonstration was given by the first-aid team of Troop One, and the entertainment was provided by members of Troop One and Twenty-eight of the Bir-mingham Scout Council, organized by the writer for the purpose of promoting interest in the welfare and safety meetings in the mining villages of the State. During the past year they have visited a number of such meet-ings and presented programs similar to the one men-tioned above. However, in order to assure a good attendance, entertainment features must also be pro-vided, and the serious part of the evening program was interspersed with excellent vocal and instrumental mu-sic, dancing and novelty acrobatic acts furnished by the visiting scouts. In addition to the numerous first-aid teams of the Birmingham Council, there are hundreds of scouts scat-tered throughout the mining district whose knowledge of first aid, safety first, life-saving, personal health and public health are a constant source of protection to their community. All of these subjects are covered by merit badge pamphlets and are required of an eagle scout.

Jan 2, 1927

By A. J. Bowie

The discovery of the auriferous cement gravel deposits in and near Deadwood Gulch, Lawrence County, Dakota Territory, in 1876, created a mining excitement, and rush to the Black Hills. Numerous ten and twenty-stamp mills were built on Deadwood Gulch; Central City and the town of Deadwood sprang into existence, and became the centres of the mining industry of the Hills. Gold quartz deposits were subsequently discovered and located on a so-called mineral belt, extending from Whitewood Creek on the south, to Deadwood Gulch on the north. A northerly group of these quartz locations was purchased in December, 1877, by parties in San Francisco, who formed a company, incorporated under the name of the Father de Smet Consolidated Gold Mining Company. This company immediately commenced the work of exploration The deposits were proved to be extensive, and easily mined, but it was found that the ore, on an average, would not yield more than $10.00 per ton* of 2000 pounds. • At this trine the cost of supplies and materials in the Hills was high. Miners' wages were $3.50 per diem, and custom mills charged $6.00 per ton. The successful working of mines on "the belt" necessitated cheap milling. The ores being of so low grade,f this could be accomplished only with large and economically running mills. To insure the greatest possible economy, the Father de Smet mill

Jan 1, 1882

By John Gross

The building of reverberatory furnaces (Fortschaufelungsofen) where ordinary brick, fire-brick and iron are comparatively cheap, is quite a different matter from the building of such furnaces in isolated camps, where proper material is only to be obtained at high cost and with long delays. Time is always a large factor in metallurgical operations, and the metallurgist may find himself in a position where it becomes necessary to erect apparatus and have it running in less time than it would take to obtain material from outside. It is here that he must make use of makeshifts. In Mexico, one of the most important of these is the alluseful adobe. Employed from prehistoric times, it still has its sphere of application in a surprisingly large number of instances requiring an article that can be quickly and cheaply produced. It is quite possible to erect serviceable reverberatory furnaces with no other materials than adobes, stone and wood. The old Mexican smelting shaft-furnace was an example of what can be done with adobes, and the large number of ruins of this class of furnace scattered through the mining districts of Mexico are silent testimony to the genius of a people who demonstrated their capability of adapting material at hand to their needs. The present paper will describe briefly the construction of an adobe reverberatory furnace which is giving good results, can be quickly erected at a low cost, and, if properly built and handled, will last a long time. The material being simply sun-dried, it naturally follows that the construction must be quite heavy. The adobes should be evenly made, with just sufficient straw to hold them together, and not too large in size (9 in. wide, 18 in. long and 4 in. thick

Jan 1, 1902

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector's hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930's in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth's crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth's surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960