Search Documents

By H. Habenicht, J. J. Scott

An experimental method is described to compare strain data for rock and rock bolts when exposed to shock waves released by blastings. Static and dynamic strains were measured. Bolt gage response indicated a static decay of the bolt anchorage coupled with a reaction due to blasting vibrations. A distinct loss of bolt tension was indicated during vibrations and this was accompanied by a smaller but steady loss of tension due to static loading. The strain losses were found to relate to the shock source distance and the vibrational amplitude in the rock and bolts. Millions of roof bolts are used each year to stabilize mine openings and prevent their failure. Frequently, bolts become loose and lose their effectiveness as reinforcement to the mine structure. Many attempts have been made to determine the cause of loosening, including observation of the bolt tension or bolt torque through the use of torque wrenches, compression pads, and load cells. Pull tests have been used extensively to determine anchorage characteristics.102 These investigations have shown that even when bolts are loaded below the nominal anchorage capacity of the rock under 'static' conditions they exhibit a decay of load through adjustments and slippage at the bolt anchor. Since bolts are quite often found with the plate hanging loose from the rock surface, this condition suggests that some additional mechanism may have played a part in loosening the anchorage. Vibration from blasting or shock loading have been suggested as one cause in this type of anchorage deterioration. This paper gives the results of an investigation carried on at the University of Missouri at Rolla to determine the influence of shock waves on rock-bolt anchorage stability. ROCK BOLT ANCHORAGE UNDER DYNAMIC LOADING CONDITIONS In this report dynamic loading conditions are defined as conditions under which rock and bolts are exposed to vibrations occurring as a consequence of blasting, machine vibrations, earthquakes, rock bursts, etc. Whatever the location of the shock source, the waves created suffer extensive alterations along their travel paths, depending upon the vibrational properties and geometric parameters of the transmitting media. Together with reflection, refraction and diffraction at material boundaries, waves suffer changes in their nature to form tensile, compressive and shear waves. They become polarized, retracted, accelerated, dispersed, so that the waves incident at a point in the material can be the result of either one or a combination of this wide range of processes. A certain fraction of the wave energy will be lost due to friction, deformation, and material failure at the anchor-rock contact. Thus, the physical nature of wave propagation is such that it inhibits an exact analytical solution. For this reason this investigation should be considered qualitative rather than quantitative even though numerical data have been used as a base. CONCEPT OF THE INVESTIGATION Experiments were designed to find, from a series of rock bolts installed in natural mine rock, whether or not, and to what extent, bolt tensions would be influenced when bolts were exposed repeatedly to shock waves such as those produced by blasting. Electronic instrumentation available in the rock mechanics laboratory of the University of Missouri at Rolla was used to observe wave development in the rock and vibrational reactions in the bolts. EXPERIMENTAL PROCEDURE Fig. 1 illustrates schematically the experimental equipment. Electric resistance wire strain gages were used as sensors for the strain response of the rock and the bolts. Bolts were 5 ft long and 5/8 in. in diam, equipped with two-leaf type expansion shells for 1 3/8 in. boreholes. The bolt gages were mounted by use of Du Pont Household Cement, covered with an epoxy insulation and then enclosed in a copper foil for electronic shielding. For details of placement and the wiring diagram see Fig. 2 and 3. The output of both the rock gages and the bolt gages was fed into cathode ray oscilloscopes from which the vibrational traces could be photographed. A static strain indicator was also used to read the output of all gages.

Jan 1, 1968

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,''2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By Paul Giesecke

Since most modern metallurgical plants are operated continuously and on a large scale, successful operation at maximum efficiency demands that an accurate knowledge of the performance at each stage of the process be available at all times. Quantitative analyses provide the most practical process guides, and it is essential to have analytical procedures that combine accuracy and speed. In continuous plant operations, large losses may occur if the time interval between the development of trouble at any stage and its recognition and correction is great. Many metallurgical plants are using rapid colorimetric and spectrochemical methods of analyses for control purposes. So-called "color coppers" may be cited as an example of the colorimetric methods, in contrast with- the routine use of the ultraviolet spectrograph for the analysis of steels.42 By means of this more refined spectrochemical procedure, a complete quantitative analysis of the molten metal is obtained every few minutes. During the past two years the Physics Division and the Ore Dressing Laboratory of the American Cyanamid Company's Stamford Research Laboratories have collaborated in a study of the use of spectrochemical methods for the analysis of various metallurgical products. New methods have been developed, which have proved of practical value in plant operation. The following pages give a general review of the principles of spectrochemical methods and also the details of several specific analyses. Principles of Spectrochemical Analysis In general, it can be said that a visible light spectrochemical analysis can be performed for any ion or molecule that is naturally colored, or that can be made to react with another to produce a colored salt or complex. Whereas transmission measurements in the ultraviolet and infrared portions of the spectrum are most useful for the analysis of organic molecules, * visible light measurements are of particular value for metal salts. Such elements as copper, manganese, cobalt, nickel, iron, molybdenum, vanadium, chromium, phosphorus, mercury, zinc, lead, and a great many others, can now be determined with a high degree of sensitivity, accuracy and dispatch. From the simplest of qualitative determinations, color analyses have been improved to such an extent that, at the present time, through the use of recording spectrophotometers, hundreds of accurate quantitative analyses can be performed by a single analyst during an 8-hr. day after the standardization curves have been established for the ions to be determined.

Jan 1, 1947

By John W. Bell

The aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½-ft. Huntington mill was used.

Jan 1, 1918

By Alan U. Seybolt

IN examination of some cold-rolled copper and cupronickel that contained a little columbium, it was discovered that these alloys were unusually resistant to annealing. This effect was sufficiently pronounced to warrant some investigation [ ] of the annealing characteristics of such compositions. EXPERIMENTAL PROCEDURE The alloys were made from cathode copper, electrolytic nickel, and a special copper-columbium hardener alloy furnished by the Electro Metallurgical Corporation. This hardener alloy contained 10 per cent columbium, with tantalum, aluminum and iron as major impurities. The melting was carried out in a clay-graphite crucible in a high-frequency induction furnace, under a charcoal or [ ] electrode carbon cover. No deoxidizing additions were made. The 7-lb. copper heats were poured into a steel mold, hot-rolled to ¼ -in. thickness, and annealed for ½ hr. at 760°C.; the cupronickels were annealed I hr. at 815°C. The material was then cold-rolled to a go per cent reduction in thickness and annealing tests were carried out on this 1/8-in. hard-rolled strip. A little silver was added to copper-columbium alloys 402 and 403 to find out

Jan 1, 1941

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 110 W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H20). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells[t] and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale[$] for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table I. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and I600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By K. M. Rolls, R. M. Rose, H. B. Shukovsky

Studies of the phase structure, critical current density, and resistive critical magnetic field of a 45 pct Nb-55 pct Zr superconducting alloy after final-size heat treatments are reported in this paper. A combination of optical metallography, X-ray diffraction, and electrical-resistivity measurements were used to determine the phase structure. Superconductivity measurements, made with heat-treated wires, are correlated with microstructure. Although no quantitative relationship between microstructure and critical current density is found, it is shown that SINCE Kunzler1 as well as Berlincourt, Hake, and Leslie2 first described the high-field, high-current-density superconductivity of Nb-Zr alloys, it has be- the critical current density is highest when the microstructure is finely divided by fibering, coring, precipitation, or fine-scale phase dispersions. The resistive critical field is very sensitive to the compositions of the phases present. Since the alloy investigated here is near the maximum resistive critical field for the Nb-Zr system, any phase decomposition results in a lower H,. Elimination of the effects of cold work lowers H, also. A possible interpretation of the latter in terms of internal surface superconductivity is suggested. come apparent that the resistive critical field and the current-carrying capacity of such alloys are, in large measure, dependent on composition and processing. The resistive critical magnetic field (Hr) for low current densities has been found to increase progressively with zirconium content until a flat maximum is reached between 50 and 65 pet Zr.3 For any single composition, a characteristic maximum value of H, is attained by heavily cold-drawn wire.4 critical current density (J,) depends not only upon cold work but also, apparently, upon microstructure. Heat treatments of cold-worked wires generally

Jan 1, 1965

By G. L. Coleman, D. S. Hutton, W. C. Leslie

The occurrence of twins in a iron, generated during cooling through the ?-a transformation, is well established,1-8 but this phenomenon has been nearly ignored during the past 20 years. It is the purpose of this note to call attention to the prevalence of such twins and to illustrate their appearance. The work of paxton7 and Kelly8 has demonstrated beyond reasonable doubt that for Neumann bands (mechanical twins) in a iron the twinning plane is (112) and the twinning direction <III>. The agreement with McKeehan&apos;s earlier work4 on transformation twins indicates that both types of twins in ferrite follow the same twinning law. There is little doubt of this conclusion, but it could be strengthened by a microbeam X-ray determination of the orientation relationship between a single ferrite grain and a transformation twin within that grain, as in the technique used by Kelly8 on Neumann bands. RESULTS AND DISCUSSION Transformation twins, identified by their appearance on a polished and etched section, were found in

Jan 1, 1960

By E. H. Cho

INTRODUCTION Activated charcoal has been used for several centuries in many capacities including the recovery, isolation and purification of various materials (1). The first use of charcoal in a gold metallurgical system was in the extraction of gold after chlorination (2, 3,4). The gold was dissolved in a chlorine system and subsequently filtered through charcoal. The application of charcoal with cyanide extraction was patented by Johnston (5) in 1894 and adopted commercially in Australia in 1897. The process consisted of dissolving the gold and silver in a potassium cyanide solution and passing it through a series of charcoal filters. The charcoal was subsequently smelted to recover the gold and silver. The interest in the use of charcoal diminished in the first part of the twentieth century as the practice of the use of zinc as a precipitating agent increased. However, in 1916, the Yuanmi Mine in Australia replaced their zinc precipitation plant with a charcoal adsorption plant. In 1926, Scott and Gross (7) of the U. S. Bureau of Mines con- ducted extensive research on the adsorption of gold and silver from cyanide leach solutions. Among their findings was the result that the most important factor in improving the adsorptive power of charcoal was heat treatment with oxidation by air or steam. The work of Zadra (8) in 1952 stimulated renewed interest in the use of activated charcoal in gold and silver recovery with the development of a method of recovery of the gold and silver from the charcoal other than its destruction by burning. The process involved simultaneous desorption

Jan 1, 1983

By Sidney L. Wise, Walter Strache

While the installation of mine bulkheads to retain water under high pressure is by no means a rarity, the following points which arose in the designing and placing of two of these bulkheads may be of interest: The Hibernia magnetite mine, located about 40 miles west of New York, in the State of New Jersey, is partly fillcd with water. This mine is located on an ore lens, the outcrop of which is over a mile long. The ore has been mined from this lens from the surface to a depth of more than 1,500 ft. It was held desirable to separate the old workings from the new, and to allow the former to fill to the 850-ft. level. Two weak places existed between the new and old workings below this Ievel: namely, a temporary bulkhead on the 10th level and a rock bulkhead of indeterminate thickness on the 16th level. When the matter of allowing the old workings to fill was investigated, the fact was developed that if these old workings were filled, the bulkhead on the 10th level would be subjected to a water pressure of about 50 lb. per square inch, and that 200 lb. per square inch would act on the 16th-level bulkhead. As the above-mentioned barriers were not deemed of sufficient strength to permit of these pressures, it became necessary to design and install new bulkheads. Design As the 16th-level bulkhead was required to withstand a pressure of 200 lb. per square inch, it presented some difficulties. A careful consideration of the various types of mine dams now in use led to the adoption of a design of the form of a truncated wedge. In this, the pressure side of the dam is of greater area than the hack, so that the resultant action is similar to driving the wedge. By cutting generous skewbacks in the walls, roof, and floor, this type in reality becomes an invisible arch. The wedge feature tends to compress the materials in the bulkhead, thereby adding to its imperviousness.

Jan 1, 1915

GEORGE OTIS SMITH, the Institute&apos;s new presi-dent, continues the long tradition of close asso-ciation between the organization and economic geology. Several preceding presidents have been eco-nomic geologists, and a gen-erous share of space in the TRANSACTIONS has always been devoted to that subject, one of critical importance to the miner as well as the seeker for ore. Mr. Smith has long served the Institute, hav-ing been a director since 1921 and first vice-president since 1927. He was born in Hodg-don, Me., on Feb. 22, 1871, and graduated at Colby College, where he took his A.B. and A.M. He did graduate work at Johns Hopkins, where he re-ceived a Ph.D. in 1896. Meanwhile he had engaged in field geological work in Michi-gan, Utah and Washington with the Geological Survey. In 1896 he joined the regular staff of that organization, be-coming director in 1907. He has been with the Survey con-tinuously since he first joined, with the exception of one year when he was furloughed to serve as a member of the U. S. Coal Commission. His special interest for many years has been in the eco-nomic aspects, in the larger sense, of the mineral in-dustry, matters that are necessarily the subject of strong differences of opinion, but which he has dis-cussed with good temper though with full adherence to his strong con-victions.

Jan 3, 1928

By W. A. Binsacca

The concentrator treats sulfide ore containing lead, copper, zinc, gold and silver, at the rate of 850 tons per 24 hr., and produces lead, copper, zinc and iron concentrates by selective flotation methods. The ore occurs below the oxidized zone along a main fracture, the wall rock of which is either greywacke or calcareous shale. The predominating sulfide minerals are galena, sphalerite, pyrite and chalcopyrite; the others are quartz and calcite. In minor amounts, arsenopyrite, pyrrhotite and hematite occur, and such secondary minerals as smithsonite, chalcocite, covellite, bornite, cerussite and anglesite are detected in the ore, the last two named occurring principally as surface alterations of the galena. The ore is hauled from the mine bins in 10-ton cars which pass over the track scales before entering the car dumper ahead of the crusher plant.&apos; A conveyor belt delivers the crushed ore to the sulfide bin, which has a capacity of 2800 tons. The primary grinding unit consists of two 6 by 12-ft. Marcy rod mills operating in parallel and in open circuit, each taking 425 tons per day. One rod mill discharges into an 8 by 25-ft. Dorr classifier with a 12-ft. bowl and the other into a 6 by 25-ft. Dorr duplex classifier. These classifiers are arranged so that each unit rakes the sands into a 6 by 14-ft. Traylor ball mill, which discharges to the bowl classifier only. The duplex classifier therefore operates in open circuit and the bowl classifier in closed circuit, the overflow of both classifiers furnishing the feed for the flotation section. Other groupings have been tried, but this has been found the most satisfactory. The Marcy mills are driven by 150-hp. slip-ring induction motors with speed reducers to give 17 r.p.m. The Traylor mill operates at a speed of 24 r.p.m. and is driven by a 200-hp. slip-ring induction motor, direct connected to pinion and gear. The bowl classifier operates at a speed of 22 r.p.m., with the bowl rake making 4.5 r.p.m. and the duplex classifier at 31 r.p.m. High-carbon steel rods of Mexican manufacture, 12 ft. long by 3-in. diameter, are used in the Marcy mills, with a resulting consumption of 1.52 Ib. per ton ore. The Traylor mill is fed 3-in. cast-iron balls cast in

Jan 1, 1935

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By Ashbel Welch

Ashbel Welch, Lambertville, N. J.: Dr. Dudley has given the wear of steel rails under four different conditions. He arrives at the conclusion that the softer rails, or those that from their composition ought to be softer, wear better than the harder. But there is another condition which has an important bearing on the subject, and should not be overlooked,—the weight on a wheel. With the lighter weights of the past, the softer rails may have worn best; with the heavier weights of the future, the harder may wear best. Weights will probably be increased up to the capacity of steel to bear; then doubtless the harder steel will wear best. A leaden rail with ten pounds on a wheel might carry millions of tons, but with one hundred pounds on a wheel, it would be destfoyed by a few thousand tons. So in the days of iron rails, my experience was that the softer rails under light machinery stood better than some of the harder; but under heavy machinery the softer were much the most rapidly destroyed. It is doubtless the same with steel. The pounding motion of the wheels loosens or spreads the particles of a thin film of steel; the pull lengthwise on the rail de-

Jan 1, 1881

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Leo B. Bicher, Donald L. Katz

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.&apos; Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By W. M. Robertson

The formation of grain boundary grooves on surfaces of poly crystalline samples of cobalt and iron immersed in liquid lead has been studied. The grooves form by volume diffusion of the solutes cobalt and iron in the liquid. The diffusion coefficients of the solutes in liquid lead are derived from the measured rate of grooving. The diffusion coefficients are described by the relation D = Do exp (-Q/RT), with, for cobalt, Do = 4.6 x 10-4 sq cm per sec and Q = 5300 ± 800 cal per mole, and for iron, DO = 4.9 x 10-3 sq cm per sec and Q = 10,500 ± 1500 cal per mole. LIQUID metal-solid metal interactions occur at solid-liquid interfaces. Interfacial energy provides a driving force to change the morphology of the interface. Mullins1,2 has derived expressions for the kinetics of interface morphology changes driven by capillarity. These expressions can be applied to an isothermal system of a solid in equilibrium with a liquid saturated with the solid. Surface profile changes can occur by volume diffusion of the solute in the liquid, by volume self-diffusion in the solid, and by interfacial diffusion at the liquid-solid interface. A groove will form at the intersection of a grain boundary with a solid-liquid interface, reducing the total interfacial free energy of the system. The solid-liquid interfacial energy ? must be greater than half the grain boundary energy of the solid ?6 for Mullins&apos; calculations to apply. If ? is less than ?b/2, then the liquid penetrates the boundaries, separating the grains rather than forming grooves. Boundary penetration did not occur in the work described here. where CO is the equilibrium volume concentration of the solid in the liquid, Dv the volume diffusion coefficient of the solid in the liquid, ? the interfacial free energy of the solid-liquid interface, O the atomic volume of the solid crystal, k Boltzmann&apos;s constant and T the absolute temperature. Eqs. [1] and [2 ] also apply to grooving by volume self-diffusion in the solid,1 with CoODv = D Self, where DSelf is the volume self-diffusion coefficient of the solid. For a grooving mechanism of interfacial diffusion at the solid-liquid interface, the groove width is given by2 where CS is the interfacial concentration of the diffusing species, and DS is the interfacial diffusion coefficient. Eqs. [1] and [3] can be used to determine the mechanism of groove growth. A t1/3 dependence of the growth indicates volume diffusion and t1/4 indicates interfacial diffusion. In some cases, volume diffusion and interfacial diffusion both can contribute substantially to the grooving process, causing the time dependence to be intermediate between t 1/3 and t1/4.3 For these cases, the relative contributions of the two processes can be separated.4 However, in many cases, one process will be dominant, and the data can be analyzed on the basis of Eq. [1] or Eq. [3] alone. The time dependences for volume diffusion in a liquid and volume self-diffusion in a solid are the same. However, the self-diffusion contribution of the solid is usually negligible compared to volume diffusion in the liquid. After the grooving mechanism has been determined, Eq. [1] or Eq. [3 ] yields the kinetic parameter A or B. The kinetic parameter can be used to calculate values for the unknown quantities in the product CD?. Usually C is known or can be estimated. If ? is known, then D can be calculated. In a measurement of grain boundary grooving of copper in liquid lead,&apos; the time dependence indicated volume diffusion in the liquid. The quantities Co, Dv, and ? were obtained from the literature, giving excellent agreement between the observed values of A and the values calculated from Eq. [2 ].5 In a study of the grooving of several refractory metals in liquid tin and liquid silver, A1len6 educed that grooves formed by volume diffusion in the liquid. In a study of nickel in a nickel sulfide melt, Steidel, Li, and spencer7 found volume diffusion grooving kinetics. Both Dv and ? were unknown, so they could not obtain either one separately, though they did obtain a reasonable value for the temperature dependence of the product Dv ?. Several methods have been used to obtain surface profiles. It can be done by sectioning through the interface7 or by chemically removing the liquid from the solid surface after solidification of the liquid.6 However, if the liquid dewets the solid on removing the solid from the melt, then the interface can be observed directly. This method was used previously&apos; and was utilized also in the present study. EXPERIMENTAL PROCEDURE Lead of 99.999 pct purity was obtained from American Smelting and Refining Co. Cobalt sheet was obtained from Sherritt-Gordon Mines, Ltd., with a nominal purity of 99.9 pct, the principal impurities being nickel, iron, copper, carbon, and sulfur. The sheet was

Jan 1, 1969

By Fred C. Bond, Walter Maxson

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943