Search Documents

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921

By R. L. Smith, J. L. Rutherford

ZONE refining, as developed by W. G. Pfann,1 has been used extensively for the purification of semiconductors. This method has made it possible to obtain the extremely high purity material necessary for the transistor industry. It has also been utilized to some extent for the purification of relatively low-melting-point metals. However, very little attention has been given to reactive, high-melting-point materials, with the exception of silicon. For this element, it has been necessary to use the floating zone technique in order to avoid contamination from the crucible containing the melt. The method is one in which a narrow molten zone is formed in a vertical rod by induction heating. The molten zone is supported between the two solid sections of the rod by surface tension. It is then moved longitudinally along the rod in order to effect a redistribution of solute. This technique has an advantage over the horizontal boat method, since crucible contamination is avoided. It has the disadvantage of being a much more difficult technique than zone refining in a crucible. Furthermore, it is necessarily a slow process, since only one zone at a time can be formed. However, the floating zone process offers a means of obtaining high-purity metals that are either not available, or can only be obtained in powder or pellet form as the result of complex chemical or electrochemical methods. It should be emphasized that the process is not effective in removing all impurity elements. Those that cannot be redistributed in an ingot during zone melting must be removed by some other means. Very little is known of the prope~ties of very high purity reactive metals such as iron, titanium, zirconium, beryllium, etc. It is quite likely that trace elements in such metals can affect their properties drastically. Therefore, one of the primary objectives of this work is to study the properties of metals which have been obtained in the purest form available and then zone refined. Trace elements can be introduced in a variety of ways, such as by inserting wafers between solid portions of the ingot to be melted, by placing the

Jan 1, 1958

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By A. P. Svenningsen

IN the early stages of design it was not considered necessary that separate crushing plants be built for the new sulphide concentrator and smelter until sometime in the future. The plan was to use the existing crushing facilities for both oxide and sulphide ore. A few additions were contemplated for the existing plants, such as increased bin capacity, and possibly two new secondary crushing units. The more the problem was studied and discussed with the plant operators, the more it became evident that it was complex. It involved the classification of different kinds of ore from the open pit mine -sulphide, oxide and mixed-and how best to separate them so that each kind of ore was given the proper processing and treatment. It also involved the problem of keeping the different ores from being contaminated in bins, hoppers and chutes. Added to these, transportation became complicated and would involve additional handling and loading of ore from crushing plants to conveyors, to bins, and finally to railroad cars which were to be hauled to the concentrator and dumped into the fine ore bin. General In the early part of 1951 it was decided that the concentrator be constructed with ten grinding units instead of seven as originally authorized. The smelter was to be increased proportionally and naturally also the overall tonnages of ore to be handled by the new sulphide plant. Due to this increase in plant capacity and the larger tonnages involved, the difficulties which would arise by using the existing crushing plants were increased to a point where it became evident that the building of new crushing plants for sulphide ore exclusively was technically, as well as economically, advantageous. Authorization was, therefore, given by the company to construct new crushing plants to handle 30,000 tons of ore per day, and capable of reducing the run-of-open-pit ore to the proper size feed for the 10x14-ft rod mills in the concentrator. The ore, mined in the open pit, sometimes comes in pieces as large as 6 to 7 ft diam. The rod mills may call for ore crushed to 3/4 in. The large .size of ore delivered from the open pit determined that a 60-in. gyratory crusher be used as primary breaker. Such a crusher will have a capacity considerably in excess of 30,000 tons per day. The crusher will be a single discharge unit driven by a 500-hp electric motor through a tear coupling and a floating shaft. This type of drive has proven successful at a number of other crusher installations which our company has operating in the United States, Mexico and South America. The tear coupling will protect both the crusher and motor against damage in case of overload. No new features are incorporated in the design of the crusher itself, except that the, discharge chute is made the full width of the crusher with parallel sides instead of the usual converging sides. This change in detail should eliminate, a feature which has been a bottleneck in some of the operating plants and has caused loss of production due to ore hanging up and blocking the chute. The secondary crushing plants will have three 7-ft standard Symons cone crushers and six 7-ft short head Symons crushers. Between the primary and secondary crushing plants a coarse ore bin will be constructed with a nominal draw-off capacity of 30,000 tons of ore. The standard Symons and the short head Symons will be in separate buildings. All the crushing plants and the coarse ore bin are interconnected with conveyor belts for transporting the ore to the crushers at the tonnage rate desired. The final product of the new crushing plants is produced by the short head crushers. It will be delivered onto a conveyor belt leading to the top of the fines ore bin in the concentrator. A separate conveyor belt running the full length of the fines ore bin and provided with a movable tripper of rugged design will discharge the sulphide ore into the bin. The concentrator bin is planned and designed so that the installation of this additional conveyor will not interfere with the operation of the two railroad tracks on which crushed ore is brought from the existing oxide plant. Thus when completed the bin can be filled simultaneously by ore from the new crushing plant and by ore from the existing leaching plant.

Jan 1, 1952

By W. C. Krumbein

GEOLOGICAL problems are approached from a geometrical (space relations) viewpoint, a kinematical (time sequence) viewpoint, or a dynamical viewpoint. The first two require sound training in conventional geology and in field methods. The third approach requires a solid foundation of chemistry, physics, and mathematics. Modern training for geologists should include close integration of basic sciences with geological principles. INTRODUCTION Our knowledge of the earth has increased tremendously during the last half century. We know more about its surface configuration, the distribution of its natural resources, the procession of living forms that inhabited it in the past, the chemical composition of its oceans, the areal distribution of its surface rocks, the movements of its atmosphere, and so on. Not only do we know more facts about the earth, but we have a better understanding of the processes that take place on and within it, such as the nature of earthquakes, the thermodynamics of the atmosphere, the chemical equilibria involved in the formation of igneous rocks, the mechanics of stream flow, the dynamics of the earth&apos;s origin, and so on. Many sciences contributed to the sum total of this knowledge, including such established disciplines as geology, geography, physics, chemistry, astronomy, biology. Out of this accumulation of new knowledge grew also a group of new sciences, such as seismology, oceanography, meteorology, volcanology, hydrology. Collectively these latter are known as the geophysical and geochemical sciences, and to a large extent they began as branches of geology. Until the turn of the century, for example, the study of earthquakes (seismology) was a part of geology, although as early as 1846 Mallet, a physicist, had suggested that the subject could be investigated by elastic-wave theory. Comparatively little progress was made along these lines until the seismograph was developed near the turn of the century; since then, additional earthquake data have accumulated rapidly, but more important, the interpretation of these data essentially has kept pace with their accumulation. In similar fashion, meteorology, was generally considered a branch of geology as recently as one or two decades ago. Considerable progress had been made in such aspects as weather forecasting, but the science dates its recent rapid rise from the year 1911, when Bjerknes first applied the principles of dynamics to the analysis of air masses. The rapid development of such disciplines as oceanography, volcanology and hydrology was due in part to the application of principles of chemical equilibrium, of dynamics, and of thermodynamics to earth problems, by men who were essentially physicists or chemists by training. The last half century, therefore, and particularly the last two decades, saw the influx of numerous chemists and physicists into the realm of the earth sciences. In the meantime the main body of geology itself showed a marked growth, and

Jan 1, 1941

By J. B. Cohen, B. W. Howlett, M. B. Bever

The partial molar heats of solution at infinite dilution in tin of aluminum at 300° and 350°C and of gallium, indium, and thallium at 240°, 300°, and 350°C have been measured by tin solution calori-metry. Aluminum, gallium, and thallium are endo-thermic on solution; indium is exothermic. Any temperature dependence of the heats of solution lies within the experimental scatter. Over the dilute ranges investigated, only aluminum has a measurable change in its heat of solution with composition. HEATS of solution of one element in another reflect the interaction between them. The investigation of partial molar heats of solution in dilute alloys is of particular interest as the properties of the solvent are altered to only a limited extent by the presence of the solute and also as the interaction between solute atoms is small. When the heats of solution of a related series of elements in a solvent are known, a systematic comparison may be made. In the investigation reported here, the partial molar heats of solution of the Group III elements aluminum, gallium, indium, and thallium in dilute solution in tin were measured. This work follows an investigation of the heats of solution in tin of the Group IB elements.&apos; EXPERIMENTAL PROCEDURES Materials. Samples of gallium, indium, and thallium were obtained from Johnson, Mathey and Co., Ltd. Indium and thallium were supplied as wire, 1.6 mm in diam; gallium was in the form of irregular pieces. The supplier reported the following minimum purities: gallium—99.95 pct; indium—99.99 pct; thallium—99.99 pct. The aluminum, obtained from Alcoa Research Laboratories, was reported to be 99.995 pct pure. The tin was supplied by Baker and Co., Inc.; the reported analysis indicated a tin content of at least 99.96 pct with lead as principal impurity. Calorimeter. this description will cover only the essential features of the calorimeter with special attention to modifications made since an earlier description was published.&apos; A Dewar flask containing the tin bath was held in a constant-temperature bath of a near-eutectic mixture of lithium, sodium, and potassium nitrates. This bath, which was stirred vigorously, was heated by a primary resistance winding in the container wall and by a secondary winding immersed in the salt. The voltage supplied to both windings was stabilized. The temperature of the salt bath was controlled by means of a platinum resistance thermometer in one arm of a Wheatstone bridge. The light from a mirror galvanometer in the bridge circuit fell on a photocell which controlled the current in a saturable reactor in series with the secondary winding. In this manner, the temperature of the salt bath was controlled to ±0.003°C and that of the tin bath to at least ±0.002°C. Each of these temperatures was measured by two iron-constantan thermocouples in series, coiled in a helix to minimize heat loss and immersed in the salt and tin baths in protective sheaths. The temperature of the laboratory was kept constant to ± 1°C during a run. Specimens were dropped into the tin bath from an addition arm held at O°C which was part of the cal-orimetric system. The system was evacuated to about 0.02 1 to minimize oxidation and to reduce transfer of heat. The bath was stirred by a glass stirrer introduced through a double Wilson seal. The samples were scraped clean before weighing, which was carried out as rapidly as possible. Each sample was immediately placed in the evacuated addition arm to minimize contamination. These precautions were especially necessary with aluminum. After the runs with gallium and thallium at all temperatures and with indium at 240° and 350°C (Series I) were completed and before the runs with indium at 300°C and aluminum at 300° and 350°C (Series 11) were begun the following changes were made. The shape of the Dewar flask was changed so as to result in a lower surface to volume ratio of the bath and at the same time the amount of tin was reduced from 500 to 400 g. The paddle type stirrer was replaced by a helical screw and the rate of stirring was increased to about 150 to 200 rpm.

Jan 1, 1962

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity-clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 1, 1986

By W. M. Weigel

The first successful use of the wire saw in slate quarrying in the United States was late in 1926, at the quarry of the Colonial Slate Co. near Wind Gap, Pa. This installation was sponsored and supervised by the United States Bureau of Mines in collaboration with the National Slate Association.&apos; The success of this trial resulted in other installations of wire saws, so that 27 were in operation at Pennsylvania slate quarries2 by October, 1928. Marble Quarrying with a Wire Saw Until recently, little or no attempt has been made to use the wire saw in the quarrying of other stone, but it is believed that its successful use in slate will be followed by attempts to take advantage of its possibilities in other quarrying operations. An example of such a trial is the recent installation of a wire saw at the marble quarry of the Saint Clair Marble Co. near Guion, in the Ozark region of northern Arkansas. This quarry is in a comparatively new district and the decision to open and develop it had to be made in the face of many unknown factors. For this reason, it was essential that the development costs be held at a minimum, and as a wire saw could be installed more cheaply than standard channeling equipment, it was decided to try it out. One factor Largely controlling the decision was that the location was peculiarly adapted to this method. The point of development selected was on the rather abrupt end of a ridge formed on the south by an almost perpendicular bluff along the White River and on the north by a rather steep slope with little or no overburden. By taking advantage of this topography it was possible to place the supporting standards for the sheaves at both the outer and driving end without the necessity of drilling or excavating openings to receive them, and to locate the motive power in line with these standards, which made it unnecessary to deflect the sheaves.

Jan 1, 1931

By M. E. Wadsworth, I. B. Cutler, R. W. Bartlett

The oxidation kinetics of ZrC was studied between 450" and 580°C in oxygen pressures from 6.5 x 10-to 1 atm using a ther mogravimetric apparatus and sized powder samples. Two parallel rate controlling processes were observed. A surface reaction occurring at the ZrC-ZrO2 phase boundary accounted for most of the oxidation and had an activation enthalpy of 46 kcal per mole. The other process, believed to be diffusion of oxygen into the ZrC lattice partially replacing carbon, had an activation enthalpy of 53 kcal per mole. The enthalpy for chemisorption of O2 on ZrC was determined to be —13 kcal per mole. Water vapor in the presence of oxygen accelerated the surface reaction rate. THERE has been little reporting of formal rate studies or attempts to ascertain the mechanism of oxidation of carbides. MacDonald and Ransley1 studied the oxidation of titanium carbide which has the same structure as zirconium carbide, fcc. They observed an initial increase in rate with increasing temperature followed by a rapid decrease through a rate minimum and a subsequent second increase at higher temperatures. The discontinuity in the rate rise was attributed to a phase change in the oxide which changed the rate determining step from the surface reaction at the carbide-oxide interface to diffusion through the oxide layer. Samsonov and Golybera 2 studied titanium carbide and reported that during the initial period of oxidation a dense film of Tic-TiO was formed followed by the formation of less adhering layers of higher oxides. The purpose of this investigation was to study the kinetics of oxidation of zirconium carbide and to attempt to gain some knowledge of the mechanism by which oxidation occurs. EXPERIMENTAL PROCEDURE Measurement of the weight gain associated with the oxidation of ZrC was used to determine oxidation rates. The principal experimental parameters were surface area, temperature, and oxygen pressure. Although moderately sized crystals of ZrC can be grown by the Van Arkel method, the only commercially available ZrC is a powder. In using powders, the surface area must be controlled either by fabricating the powder into a sintered pellet with a measurable surface area, relatively fixed during oxidation, or by using sized unconsolidated powder and applying appropriate geometric considerations to the shape of the grains to correct for their diminishing surface areas as they oxidize. Both techniques involve some difficulties. pellets of binder-free zirconium carbide can be made by hot pressing, but it is difficult to obtain densities greater than 90 pct of

Jan 1, 1963

By J. A. Jaekel, W. C. Aitkenhead

Uranium deposits in the Spokane Indian Reservation, as well as those around Mt. Spokane, are essentially low grade, much of the ore containing less than 0.2 pct U3O8. The Mining Experiment Station of the Division of Industrial Research, State College of Washington, has been engaged in intensive research on the amenability of these low grade ores to froth flotation. The results: successful flotation of autinite, chief mineral constituent. At the outset of this work the goal was a concentrate of 1 pct U3O8 with a 90 pct recovery from ores containing less than 0.2 pct U3O8. Most of the work has been done on argillite ore from the Midnight mine on the Spokane Indian Reservation. The goal has not been attained using this ore, but samples of the granite ore from Mt. Spokane yielded successful results. For example, a concentrate containing 11.2 pcl U3O8 was produced from a Mt. Spokane high grade ore containing 1.27 pct U3O8 with a recovery of 97.8 pct. Another Mt. Spokane ore yielded a concentrate of 5.0 pct U3O8 from an ore containing 0.13 pct U3O8. with a recovery of 85 pct. This same ore gave a recovery of 93.5 pct when the grade of concentrate was reduced to 2.0 pct. It has been concluded that a successful method for floating autunite has been developed and that the mediocre results from the Midnight argillite ore are probably caused by the presence of some other uranium mineral or minerals less amenable to these reagents. The experimenters tested a third type of Washington ore, found on the Northwest Uranium Mines Inc. property on the Spokane Indian Reservation. This is a conglomerate of pebbles and small boulders of partially decomposed granite and is shot through with autunite. Its characteristics lie between those of the Midnight ore and the granite ore from the Spokane district. It responds better than the ore from Midnight but not as well as that from Mt. Spokane. As the fatty acids are the only type of collectors showing promise, investigation has been concerned with these acids and the optimum conditions for their use. The first method for treating the argillite ore from the Spokane Indian Reservation made use of Cyanamid&apos;s R-708 as a collector, a tall oil product described as a substitute for oleic acid. Although the investigators proved that R-708 is a collector for autunite when mixtures of autunite and silica sand are used, results on the ore were mediocre. Tests of other fatty acids revealed that the solid fatty acids of the saturated series are collectors for autunite and that their collecting power increases with the length of the carbon chain. The even carbon members of the whole series were tested from the 10 carbon acid (capric) to the 22 carbon acid (be-henic). The least expensive collector, stearic acid (18 carbon), proved to be a good one, so this was used in most of the tests. In first attempts with stearic acid, the collector was dissolved in various hydrocarbons and the solutions were added to the flotation cell. Cyclohexane, gasoline, fuel oil, kerosene, and other solvents were tried. Small amounts of high grade concentrates could be brought up, but recoveries were low. Finally emulsions of stearic acid were tried. It was discovered that stearic acid alone has little collecting power except when conditioning is carried out at high temperature. When hydrocarbon solvents were also present, it proved to be an excellent collector. An example of one emulsion that proved satisfactory for some ores is given as follows: 1 part stearic acid by weight, 1 part sodium oleate by weight, 1.2 parts kerosene by weight, 100 parts water. In some successful tests part of the stearic acid was replaced by oleic acid. The emulsions were made by agitating the stearic acid and sodium oleate together with hot water, then adding the kerosene and agitating while cooling. In the five tests reported in Table 1, 650 g of ore were ground with 650 cc water in a laboratory rod mill. The pulp was filtered to eliminate excess water and the ground ore transferred to a stainless steel beaker for conditioning at high pulp density. In most of the tests sodium hydroxide was added to the conditioner during agitation, then the collector emulsion, and finally the sodium silicate. The amount of alkali was adjusted to give a pH of 8.5 to 9.0 in the flotation cell. After conditioning the pulp was transferred to a laboratory flotation cell and the test completed in a normal manner. It is interesting to note that a deposit of high grade concentrate forms on the conditioning agitator and in the conditioning vessel, and at times on the agitator of the flotation cell itself. A few grams of concentrate running as high as 4 pct U3O8 were recovered from the conditioner when Midnight ore containing less than 0.2 pct U3O8 was treated. In the examples given in Table I this conditioner concentrate is calculated as part of the total concentrate. The authors have not yet fully explored the possi-

Jan 1, 1960

By R. D. Gibbs, C. C. Taylor

The gas-lift, or circulation of gas for the production of crude oil, now includes the gas operator in field production activities to a greater extent than ever before. It is the purpose of this paper to show the scope of his activities and to discuss the various means of handling and treating the large quantities of gas which are now of a somewhat different nature than formerly. The extent of the stripping action of circulating gas on oil must be discussed, as this can be governed somewhat by the method of treatment of the recirculated gas. Change in Gas-decline Curve under Circulation Before the advent of the gas-lift, the gas-production curve of a field showed a peak during the flush production with a rapid decline as the wells were put on the pump and then a long steady decline curve of a relatively small volume of rich gas for the life of the field. Under the gas-lift method of production, instead of having the sharp decline at the end of the flush production period, sufficient circulating gas to keep up the required total gas-oil ratio would be turned to the wells. The gas-production curve then assumes a long gradual decline, giving a large volume of gas for treatment for several years to come. The gas-decline curve will not follow that of the oil, as the lowering of the rock pressure by the steady production of oil and gas from the sand will make it necessary to continue using the large tubing and to circulate large volumes of gas in order to keep the back-pressure against the sands as low as possible. A Complicated Distributing System In tracing the flow of the gas from the time it leaves the well until it again enters through the casinghead, under high pressure, we get a very good idea of the complex distributing and regulating system that must be installed and the large treating and compression plants that are necessary (see Fig. I). Gas traps must be large enough to efficiently separate large quantities of gas and oil and should be elevated sufficiently to enable the oil, if

Jan 1, 1928

By R. B. Tippin, J. S. Browning

The feasibility of multistage heavy liquid cyclone beneficiation of spodumene was successfully demonstrated in this investigation. The indicated recovery for the multistage circuits was mathematically estimated as continuous test runs would be necessary to determine the true influence of a middlings recycle. In the three-stage circuit, both the concentrate analysis and spodumene recovery exceeded 90%. The two-stage circuits were unable to simultaneously yield an acceptable produce with a satisfactory recovery. With the Nation&apos;s growing industrial mineral requirements, the U.S. Bureau of Mines has undertaken the task of investigating new mineral dressing techniques and improving the existing concentrating methods of ore beneficiation. One such project is the gravity concentration of minerals using heavy liquid separation (HLS).1-3 Heavy liquid separation is based on the simple principle that a material, whose specific gravity is less than the density of a solution, will float on top of the liquid and a material with a greater specific gravity will sink. Heavy liquid separation techniques were developed in the laboratory over half a century ago but the process has yet to be commercially adopted. In the past, commercial operations have failed because of numerous problems.4 Industrial interest has recently been reactivated because of engineering advances. The number and quality of the heavy liquids suitable for mineral processing has increased while the cost has sharply dropped. New and improved liquid recovery systems5,6 are under consideration with present emphasis on 1) solvent extraction, 2) thermo-evaporation, and 3) water washing. The toxicity of the heavy liquids7 presents a problem, but throughout the chemical and mining industries, many similar hazardous materials are safely handled. A distinct advantage of using heavy liquids is its ability to provide a near perfect separation of fine-sized mineral particles even when the specific gravities are close. Effective separations have been made on minerals down to 200 mesh and with a density

Jan 1, 1968

As described in the section on the Palabora twin crushers, the Palabora ore consists of two types: a carbonatite containing a low titanium magnetite, and a foskorite containing high titanium magnetite. As the Palabora pit was widened and deepened, more and more of the foskorite had to be mined. The 25,000 mt expansion of the Palabora plant which went into operation in early 1977 therefore takes its feed from the foskorite section of the orebody. For the expansion, a third 54 in. by 74 in. gyratory crusher was installed to crush feed for two 32 ft by 15 ft (9.75 by 4.6 m), 9000 hp (6710 kw) autogenous single -stage grinding mills. These units are located near the two existing primary crushers, and the ground ore is pumped 5277 ft (1640 m) to the expanded flotation plant by five stages of centrifugal pumps. The new gyratory is installed in a unique Figure-8 shaped enclosure with the crusher in the smaller 27 ft 11 in. (8. 5 m) diameter cylinder and the maintenance area in the 36 ft 1 in. (11 m) diameter cylinder. Cylinder walls are only 23.6 in. (600 mm) thick because their circular design permits all the concrete to be in compression. A rectangular dump pocket which sits on the smaller cylinder contains two manganese steel faced splitters to protect the crusher spider and countersunk water spray headers under the dumping positions for dust suppression. The dump pocket holds 330 st or 300 mt and is also lined with manganese steel. The crusher is mounted on a reinforced concrete diaphragm over the 363 st (400 mt) crushed ore pocket. In the back of the pocket is plastic pipe. Radioactive level control sources are lowered into this pipe from the crusher support floor. The pipe is protected by concrete covered with steel castings. Level control detectors are mounted on the front wall of the pocket. Liner plates on the crushed ore pocket walls are removed and in- stalled by the use of a circular monorail and trolley mounted on the pocket ceiling. The door in the front of the crushed ore pocket is hinged at the top rather than at the sides and is raised by an electric winch. For removal of the eccentric, rails are installed in the pocket and a unique hydraulically operated cart is moved under the eccentric. A platform is raised to receive the eccentric and lowered so that it may be removed. Crushed ore is removed from the pocket by a hydraulically powered, 8 ft

Jan 1, 1978

By M. J. Shulman

With the spiraling cost of exploration, all stages of exploration must be optimized. Search theory calculates the optimal distribution of effort by maximizing the probability of discovery under the constraint that the total exploration budget is not exceeded. It may help formulate strategies during the reconnaissance phase of exploration. An incremental optimization analogous to the exact solution of the search problem is introduced. In conjunction with the optimization, various stopping criteria can be defined. The stopping criteria terminate exploration in an area during a particular stage. It does not refer to abandoning exploration. The following stopping criteria were considered: the exploration effort in an area should not exceed a maximum value; the posterior target location probabilities should not be less than a percentage of the initial probabilities; the change in the posterior target location probabilities should not be less than a given value; and the change in the marginal rate of return should not be less than a given value. The incremental optimization and the stopping criteria are used to allocate reconnaissance mapping and sampling effort for phosphorite in the Sinai Peninsula, Egypt.

Jan 1, 1986

By J. Allen Veatch

THERE exists in., the territory embraced between the summit of the Sierra Nevada and the coast a great dike and vein system that appears never to have been recognized in its entirety, nad many facts concerning it have never been published. This is important, not only in affording numerous clues bearing on the origin, nature, and age of the mercury deposits, and eliminating many controverted questions, but it. incidentally affords numerous facts bearing on the genesis of gold, copper, chromite, magnesite, dolomite, a type of calcite deposit, and numerous associated minerals. The mineral springs of the State almost without exception emanate from these dikes. A great range of the hydrocarbons also exists throughout the entire system of these dikes. Seepages from their, walls have frequently been mistaken as emanating from the inclosing sandstone and shale, resulting in heavy expenditures in the futile development of these Cretaceous beds, which contain no petroleum within the territory. The theory of mountain making by lateral or tangential pressure is inconsistent with some of the following recorded facts. The limitations of this paper do not admit of a description of each of the hundred or more mercury deposits embraced in the area, and therefore only typical examples will be described. The accompanying map, Fig. 1, is not submitted as complete, or as entirely accurate, but it is as nearly so as the notes at hand will admit. The field is too extensive to be completely covered by a single individual. The heavy continuous lines represent sections actually surveyed! The sections and extensions- in. dotted line are assumed, and are either unsurveyed, or -buried under younger beds. There are numerous branches connecting the great parallels that the small-scale map does not admit of plotting, even if the survey had been complete. Likewise, the conclusions in some instances may be faulty, but it is to be hoped that as a whole they may serve as a foundation on which a more complete structure may be built in the future.

Jan 2, 1914

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By C. G. McLachlan

THIS paper outlines a series of tests carried out during the first six months of 1927, in the laboratory and mill of the Moctezuma Copper Co. The object of the tests was to determine whether the soluble salts present in the mill circuit water were having a detrimental effect on the recovery made by flotation. To accomplish this object a series of water analyses were made, followed by flotation experiments in which definite quantities of the salts found were added as addition agents. Before proceeding to describe the results obtained in the course of the investigation, reference will be made to five articles that have appeared during the last two years in which the action of such salts is discussed. Two of these are by A. T. Tye1,2 and describe flotation practice at Cananea and the way in which water high in ferrous and ferric salts is conditioned for differential flotation. Two, one by A. C. Munro and H. A. Pearse3 and the other by H. A. Pearse,4 outline Britannia milling methods, and the advantages that have been derived from ore washing; while in the fifth, A. W. Hahn5 summarizes the results of laboratory experiments in which ferrous, ferric and aluminum sulfates have been added in varying amounts. The mill of the Moctezuma Copper Co. has a daily capacity of 3000 tons, and is situated about 75 miles south of Douglas, Arizona, on the Rio de Nacozari, in the Mexican state of Sonora. The ore treated is mined from the company&apos;s mine at Pilares, about 5 miles southeast of the Concentrator. This ore contains about 2.5 per. cent. copper -- present almost entirely as chalcopyrite-and 10 per cent. iron, of which

Jan 1, 1928

By C. Z. Serpan, L. J. Wittenberg

The density of liquid plutonium was determined, by a pycnometm&apos;c technique, from 664 to 788°C and exhibited a temperature dependence, which could be expressed as:. P= C17.63 - 1.52 x 10-"t] +0.04 g per cc where t = OC. These density values compare favorably with the values previously obtained by a technique utilizing Archimedes&apos; principle. The apparatus and method were evaluated when the densities 0.f molten tin and bismuth were measured and found to be in agreement with accepted literature values. PLUTONIUM or an alloy of plutonium in the liquid state has been proposed as a fuel for a fast-breeder type nuclear power plant.&apos; Since knowledge of the liquid density of plutonium is required for the proper design of such a system, this study was undertaken. In addition, the density and volume expansion coefficient of liquid plutonium are of interest for comparison with these same properties of the six allotropic modifications of the solid metal. Comstock and GibneyZ were first to report a value for the density of liquid plutonium. The value for only one temperature, 665"C, was calculated from data obtained by the radiography of the meniscus, Fig. 3. Recently, the density at a series of temperatures has been reported by Knight,3 who obtained his values by using a differential volumeter, and by 01-sen, Sandenaw, and Herrik, who obtained their values from measurements of the loss in weight of a tungsten bob immersed in the liquid. The density of liquid plutonium reported here was determined by a vacuum pycnometer method. In an evacuated system, the tips of calibrated tantalum pycnometers were lowered beneath the liquid sur-

Jan 1, 1962

By D. R. George, J. R. Ross, J. D. Prater

In the United States nearly 200,000 tons of copper per year are being produced, by leaching waste rock and oxidized copper ore with dilute sulfuric acid-ferric sulfate solutions and precipitating the copper on scrap iron. The flow of solutions is in excess of 80 million gpd. A survey conducted by the U.S. Bureau of Mines in late 1965 at 14 mines in Arizona, Utah and Nevada, showed that with a few exceptions, the solutions contain from two to a maximum of 15 ppm U3O8, and there is strong evidence that these represent equilibrium concentration and not merely an accumulated in-process inventory resulting from recycling the solutions for many years. Consequently, it is believed that uranium could be recovered at a constant rate as long as mining and leaching operations continue. Preliminary surveys and estimates by the USBM indicate a production potential of possibly 1000 tons of U3O8 per year at a cost of less than $8 per lb if the major process streams from most of the large copper mines in the western United States were to be treated. Laboratory research by the USBM showed that the uranium could be efficiently recovered as a specification-grade uranium concentrate by a combination of ion exchange resin and solvent extraction of liquid ion exchange techniques. A joint pilot plant investigation by Kennecott Copper Corp. and the USBM was conducted on solutions from the Bingham Canyon mine to evaluate a new system of countercurrent ion exchange developed during the laboratory studies. In subsequent small-scale continuous tests, recovery of uranium from the pregnant eluate by solvent extraction and chemical precipitation techniques was investigated.

Jan 1, 1968

By W. Luyken

A NUMBER of articles have been published, notably those by R. S. Handy, R. T. Hancock and A. P. Watt in Engineering and Mining Journal, dealing with the calculations involved in ore dressing.. These publications demonstrate both, the importance of the subject and the lack of success in developing a generally recognized method for comparing enrichment effects. Considering that we may wish -to compare enrichment results on similar or dissimilar ores, that we may desire to make the comparison on the basis of either the absolute or the economical efficiency, and that the number of factors upon which the result depends is large, the question arises whether it is possible to set up a positive method for such calculations. In the following pages it is our aim to show that a sure, complete and successful way to overcome existing difficulties has been found. GRAPHICAL ANALYSIS OF ORE-DRESSING PROCESSES The following is from Truscott&apos;s Text Book of Ore Dressing (London, 1923) x = assay of ore treated (feed). y = assay value of the concentrate. z = assay value of the tailing. a = weight of feed. b = weight of concentrate. c = weight of tailing. C = fractional concentration = b/a= x-z/y-z (1) K = ratio of concentration = 1/C = a/b =y-z/x-z (2) R = fractional recovery = yb/xa = Cy/x. (3) 100R = percentage recovery. Copt = theoretically best concentration. 100 - Copt = waste in the feed.

Jan 1, 1929