Search Documents

By W. L. Korbee, P. Hazebroek, M. Prats, E. E. Allen, C. A. 225-000-000-017 Verbraak, H. C. van Elst

In a recent paper,' one of us has presented some experimental evidence on the relationship between twinning and brittle fracture in steel. From metallographic examinations of brittle fracture it could be derived that mechanical twins and microcracks are formed already in front of a running brittle fracture. A tentative explanation based on the evaluation of the statistical distribution of mechanical twins vs various angles to the fracture was given in the above mentioned paper. It was suggested that these twins are caused by stress waves emitted by a running brittle fracture. With the aid of high-speed photography and the use of photo-stress sheet we are now able to study in more detail the propagation of a brittle fracture and the emittance of stress waves connected with fracture. A typical example is given in Fig. 1. In this figure a running brittle fracture in an ordinary Thomas steel is shown. The experiment was performed on a Robertson apparatus and the stress waves caused by the fracture were made visible with photo-stress

Jan 1, 1962

By A. N. Holden

A DISLOCATION mechanism has been described by Cottrell' by which metals can yield locally, I. form Liiders bands, giving rise to a characteristic stress-strain curve with a sharp yield point and appreciable strain at constant or decreasing stress. It is undoubtedly the best mechanism that has been suggested to date." In its present development, however, the dislocation mechanism provides a more satisfying explanation for the sharp yield point than for the extensive localized flow occurring at the lower yield stress. The primary objective in this paper is to extend the dislocation mechanism to account for localized cataclysmic flow by a dislocation collision process and to give experimental evidence to support such a process. Only the yielding of iron containing carbon -will be discussed, although other metal-solute systems are known to behave similarly. Cottrell Mechanism In brief, Cottrell explains the yield point in the following way: The dislocations in iron which must propagate to produce slip usually lie at the center of local concentrations of carbon atoms, since segregation about these dislocatlons relieves some of the local stress resulting from them. A dislocation surrounded by a "cloud" of carbon atoms is thus anchored, and a higher stress is required to set it in motion than to move a free dislocation. Considering all available dislocatlons to be anchored in this fashion, the iron exhibits a yield point when the first dialocations break free and move through the lattice causing slip. This first breaking away of a dislocation enables other dislocations to break loose by "interaction" and the process becomes a cataclysm producing local deformation or Luders bands. The yield point in the stress-strain diagram for iron is absent in freshly deformed material, but returns gradually with time; the phenomenon is one aspect of what is called strain aging. The rate at which the yield point returns following straining depends on the temperature of aging. According to Cottrell the rate of return of the yield point in strained iron is limited by the rate of diffusion of carbon at the aging temperature, the mechanism is onr: of reforming the solute atmospheres around carbon-free dislocations that had stopped moving coincident with the removal of stress. If the specimen is retested immediately after straining and unloading, carbon will not have had time to diffuse to, and re-anchor, dislocations and the yield point will not occur. The carbon diffusion limitation for the rate of strain aging apparently applies if the criterion for strain aging is either the change in hardness" or the change in electrical resistance" of the strained speci- men with aging time. The possibility exists, however, that the yield point actually returns to strained iron at some rate other than that deduced from hardness or electrical resistance data. Therefore, as a preliminary experiment, the rate of yield point return in a rimmed sheet steel strained 6 pct in tension was measured at 27°, 77°, and 100°C. A plot of yield-point elongation for each of these temperatures against aging time appears in Fig. 1. The aging process is described by curves which rise to a plateau value of elongation that seems independent of temperature, but at a rate that depends on temperature. Very long times lead to a further rise in the yield-point elongation above the plateau value. However, if the later increase in yield-point elongation is ignored and the log of the time to reach half the plateau value of elongation is plotted against 1/T, a straight line results for which an activation energy of about 25 kcal pel- mol may be assigned. Within the accuracy of this sort of experiment this is approximately the activation energy for the diffusion of carbon in iron (20 kcal per mol), and the carbon diffusion limitation suggested for the yield-point return on strain aging is valid. The Cottrell mechanism thus explains in a qualitative manner the occurrence of a yield point in iron and its return with strain aging. It fails, however, to explain some of the other experimental observations that have been made of the yielding behavior of iron. For example, it is known that the yield point in iron becomes less pronounced with increasing grain size. Annealed single crystals of iron have very small yield-point elongations .if indeed they have any,' compared to a polycrystalline steel. If the only requirement for a yield point is that the dislocations in the lattice of the annealed. material be anchored by carbon atoms, the difference in the behavior of single crystals and polycrystals is not explained. That a dislocation mechanism may be entirely consistent with little or no yield point in an annealed single crystal will become apparent later when dislocation interaction is discussed. Strain aging produces a definite yield point even in single crystals. This accentuation of the yield-point phenomenon in single crystals after strain

Jan 1, 1953

By Henry Louis

The object of the present paper is to call attention briefly to a novel method of analyzing the action of the ordinary gravity stamp, which has not only thrown much light upon the exact motion of the stamp-head, but promises also to be of value in determining the efficiency of a new mill before setting it to its work of crushing, and in this respect should be of service to constructors of mining machinery as well as to mining engineers. The method was devised by Mr. D. B. Morison, and developed in connection with his experiments on the comparative crushing-effects of his patent high-speed stamp and the ordinary cam-stamp, which were carried out at the works of Messrs. L. Richardson & Sons, Engineers, Hartlepool, and on which he read a paper at Newcastle in 1897.* Mr. Morison's experiments were of a very exhaustive nature; and having been consulted by him during his investigations, I had frequent opportunities of examining the methods employed and the results obtained. Experiments were first made with an apparatus resembling the indicntor of a steam-engine, inasniuch as the drum revolved alternately backwards and forwards, thus producing a closed diagram. This form was not found satisfactory, and it was therefore altered so as to cause the drum to revolve continuously in one direction, thus giving a continuous or open diagram. The arrangement is shown in plan in Fig. 1; a collar, A, surrounds the stamp-stem loosely and works between the guides B, B, which constrain it to move in a vertical line only. Immediately above it and below it, a couple of collars are clamped to the stamp-stem, so that the latter, while free to revolve,

Jan 1, 1899

By C. H. P. Lupis, R. Hocine, G. Bernard

The necessary and sufficient conditions for the stability of a multicomponent phase with respect to infinitesinzal fluctuations are derived and transformed to be written in terms of activity coeffcients and mole fractions rather than in terms of the customary second deritlatives of the free energy. NECESSARY conditions for the stability of a multi-component system were derived by Gibbs as early as 1876.' However, as the usefulness of these conditions is greatly enhanced by the simplicity of their translation in terms of functions of common usage, the present contribution establishes these conditions in terms of activities or activity coefficients-and mole fractions. It was shown in another article2 that not only may these conditions be used for the prediction of the appearance of new phases, but they may also provide a check on the orders of magnitude of the interaction coefficients involved. "Spinodal" decomposition is said to occur when, at constant temperature and pressure, the system is unstable with respect to infinitesimal fluctuations in composition. As a result, the "phases" which appear may be attained through continuous changes in the system rather than discontinuous ones, and, consequently, the free energy of these phases may be described by a unique continuous free-energy function. For a binary system, the familiar curve of Fig. 1 illustrates the case we wish to extend to a multicom-ponent system. The conditions to be written pertain to the decomposition of a system of n moles into moles of phase moles of phase v, ...hen moles of phase 9, where the phases a, ...v, ...9 are—at least initially-arbitrarily close in composition to that of the original phase. Each A, is positive and since the total number of moles n in the system remains constant: Each phase v contains hv(nl +dnY) moles of component (I), ...xV(ni +dny) of component + dnk) moles of component (m). The total number of moles ni in the system remaining also constant, it is clear that:

Jan 1, 1968

By C. Baldwin Sawyer

J. S. Vanick,* Washington, D. C. (written discussion).—To those who have been confronted with the study of the gas-metal reactions, this paper is a most welcome contribution. My personal interest in work bearing upon this general problem, stimulated by an appreciation of the difficulties inherent to problems of this type, prompts a few words of discussion. Table 2 of the paper shows a gradual increase in the nitrogen content with an increase in pressure, and an interpretation follows in which nitrogcn is used as the compressed medium when the conditions admit that cyanogen gas could be active as a contaminating ingredient. Fusions of electrolytic iron made in the induction furnace in an atmosphere of deoxidized nitrogen and out of contact with contaminating materials have shown no microscopic evidence of -a nitrogen increase; using a refractory-lined graphite crucible in the furnace under the same conditions or admitting air often resulted in the occurrence of nitride needles in the solidified melt. These results suggested that a nitrogenous compound served as a vehicle for the introduction of nitrogen and that such compound was not available when the pure gas and carbon-free refractory were used. The fusion of pure iron in pure nitrogen is perhaps a matter of theoretical interest. The author's work serves a more practical purpose when applied to steels rather than iron. Table 2 reports the absence of nitride needles in melts made under pressure of one atmosphere, although the quantity of nitrogen present would seem to exceed microscopically detectable percentages. In some recent work29 on carburized iron, nitride needles have been observed in areas analyzing as low as 0.015 per cent. nitrogen. This low percentage of nitrogen would indicate that the solubility limit is less than 0.030 per cent. for hypoeutectoid steels. There is the possibility that the areas of pearlite which exist in a hypoeutectoid steel restrict the distribution of nitrogen and limit its presence to the ferritie fields. In view of this work and the references quoted by the author, I am led to expect that the value for the solubility of nitrogen in solidified iron may approach

Jan 1, 1924

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Ernest Darby

WHEN bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag may be incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal. When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not mixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag: From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below.

Jan 1, 1928

By C. E. McCarthy, A. George Stern, Stanley J. Green

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By A. George Stern, Stanley J. Green, C. E. McCarthy

The national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of 1914-18 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. Wyomingite Deposit For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the south- western part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, 12; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the Wyomingite has a potash Content averaging slightly higher than eleven per cent K2O. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1948

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By A. F. Bertuzzi, M. R. Tek, F. H. Poettmann

A method is presented for predicting pressure drop for two-phase fluid flow in horizontal pipes. A set of 267 experimental measurements randomly sampled from approximately 1,000 measurements from various literature sources was used. Pressure gradients calculated by the procedure developed and compared with the experimental values showed a bias of +0.82 per cent and a standard deviation of 20.8 per cent. The advantatges of this method over other available methods of predicting two-phase flow pressure drop are (a) its comparative simplicity of application, (b) its relative independence of flow patterns, (c) its accuracy, which on the basis of a statistical evaluation predicts pressure drop closer than other available methods, and, (d) its ability to satisfactorily correlate laboratory data from various sources while the correlations from these sources do not appear to agree with one another. The method has been reduced to a simplified graphical procedure, suitable for field use. A two-phase f factor is defined and correlated with parameters involving the flowing gas-liquid mass ratio, a Reynolds number for the gas phase, and a Reynolds number for the liquid phase. The choice of parameters allows the correlation to reduce to the usual f factor plot for the limiting conditions of (111 gas or all liquid. INTRODUCTION The mechanics and characteristics of two-phase flow systems have been of interest throughout the industry for some time. In numerous engineering installations such as pipe lines, chemical reactors, and heat exchangers, two-phase flow conditions are of every day occurrence. In oil production operations it has been desirable, in some cases, to consider transporting gas and oil together in a common pipe from oil field to process plant. The trend toward centrally located stock tank batteries in oil fields has resulted in longer gathering pipelines in which more than one fluid phase is flowing. The increase in the producing capacity of oil wells due to new production tech- niques has created the need for review and re-design of many surface gathering lines for properly handling the increased production. Optimum pipe size for the situations described above has become an important factor. The problem which is of interest here involves the ability to predict the relationship between pressure drop, fluid properties, fluid rates, pipe diameter, and pipe length. Although the literature1,5,10,13,18,19 contains various articles dealing with specific cases of the problem, Lock-hart and Martinelli17 proposed the most general solution. Their method has been later modified by Baker:1 Alves2 demonstrated that different flow patterns are possible for a flow mechanism defined by Martinelli such as gas turbulent, liquid turbulent. Baker explained deviations experienced with Martinelli's correlations on the basis that different flow patterns could exist for the same flow mechanism. Using Martinelli's method of correlatioil, Baker correlated data for each flow pattern for the turbulent-turbulent flow mechanism. Bergelin and Gazley6,7 presented a correlation for predicting gas phase

Jan 1, 1957

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By William Daly

THE application of artificial refrigeration, or air-conditioning, to the ventilation of deep, hot mines has long been a subject of interest to the operators of such properties. Artificial cooling of the air in theaters, railroad coaches, and various industrial plants has been so successful within recent years that it has been natural to assume that the adoption of similar methods would afford a ready solution to the difficult problem of mine ventilation. It should however, be obvious, that although there may be nothing technically impossible in the application of this process to mine ventilation there is a great economic distinction between the maintenance of a high standard of comfort for a large number of people in a relatively small space such as a theater and the cooling of air to improve working conditions for miners scattered throughout the extensive workings of a large mine. Many methods of air-conditioning have been considered by the management of the Anaconda Copper Mining Co. at various times, but until the development of the process to be described in this paper none has seemed economically practicable.

Jan 1, 1934

By Herbert H. Uhlig

A STUDY of passivity in chromium-iron alloys holds considerable interest, both because of the present-day practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surface.† Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.1 He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1947

By Ligon Johnson

. Only the acute phase of the smelter fume problem is new. The problem itself is older than the Christian era. While both lead and copper were mined and crudely smelted some 3000 years ago, it was not until the Roman occupation of the Iberian . Peninsula and the British Isles, which occurred but shortly before the beginning of the Christian era, that there was any evidence of smelting operations on a scale sufficiently large to permit a fume problem. Around Huelva, Spain, are found more than 30 million tons of slag from lead smelting conducted there by the Romans. Pliny tells US that more than 20,000 slaves were employed in the Iberian mines. Extensive mining and smelting by the Romans in England and Wales were coincident with the Iberian proceedings. These metallurgical operations were upon a sufficiently large scale to produce marked results both upon the surrounding country and the smelter workers, but, as they were those of a conqueror upon conquered soil, conducted by slaves, imperial Rome failed to recognize that such a thing as a smoke problem did or could arise, and whatever fume question there may have been at that time remained a question only to those who had no chance to answer any phase of it. The smelting operations of the Romans extended over about 400 years, and little is recorded of lead and copper smelting from that time until the 16th century. From the revival beginning at this period up to the present century, the growth of smelting has been comparatively gradual. In Great Britain, smelting was conducted almost wholly in localities where metallurgical operations were of paramount importance, and the communities .that grew up in smelter localities were due to and dependent upon the mines and smelters. This fact had much to do with the comparative freedom of British smelting from burdensome fume litigation and legislation. To a lesser degree these conditions applied to the German operations which, when coupled with the further fact that most of the early German operations were to a greater or less degree fiscal workings of Prussia, Saxony and Brunswick-Hanover, accounts for

Jan 1, 1918

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967