Search Documents

By W. N. Tanner

THE wire-rope hoisting conditions at the mines of the Anaconda Copper Mining Co. in Butte, Mont., are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte, hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 ½ in. rope. 5 main hoists using 1 ¼ in. rope. 6 shafts using 1 1/8 in. rope. 2 chippy hoists using 1 ¼ in. rope. 9 chippy hoists using 1 1/8 in. rope. 15 shafts using 1 in. rope. 7 shafts using 7/8 in. rope. 1 shaft using ¾ in. rope. In addition, there are a number of sinking engines using 5/8 in., ¾ in., 7/8 in., and 1 in. (15.9, 19, 22, and 25 mm. rope.) The flat ropes run from ½ by 7 ½ in. (12.7 by 190.5 mm.) to ½ by 4 ½ in. (9.5 by 114 mm.) and are used on the older hoisting-engines, which are set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties in operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes.

Jan 2, 1922

By Jed H. Mosgrove, Paul M. Budzak

INTRODUCTION Good mine ventilation starts at the drawing board. A coal mine will either be adequately ventilated or not, depending upon how good a job was done in the planning. Poor planning will not only result in inadequate ventilation, but may also lead to low productivity. A mine foreman cannot achieve high productivity while trying to maintain 4.2 m3/s (9000 cfm) of air at his last open crosscut. PLANNING What will provide adequate ventilation? A rule of thumb in laying out a coal mine is to provide enough entries in the main entry system to keep air velocities at 2.5 m/s (500 fpm) or less; at this rate of flow, good ventilation may be expected. The intake and return air courses of a coal mine do not improve with age. Entries will deteriorate, ribs will slough, roof will fall, and clutter will accumulate. The resistance offered to air travel will continue to increase with each passing year. Providing enough airways for the present and the future cannot be emphasized too strongly. In order to better appreciate good planning and bring it into better focus, assume a hypothetical mine has the following features: entries 1.5 m (5 ft) high and 6.1 m (20 ft) wide; one intake and one return entry; the mine development is 4.8 km (3 miles) from the intake and upcast ventilation shafts; and the ventilation requirement is 141.6 m3/s (300,000 cfm) . Air travel of 4.8 km (3 miles) into a mine and the same distance back to the fan is not unusual. However, to do so with one intake and one

Jan 1, 1981

SOUTHERN CALIFORNIA SECTION Executive Committee SEELEY W. MUDD, Chairman. C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins. Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER A. B. W. HODGES WILLIAM F. STAUNTON The third meeting of this winter season tool: place in a private dining room of the Sierra Madre Club in Los Angeles on Feb. 1, 1916, at 6:30 p.m., 22 members and guests being present. In the absence of the Chairman, S. W. Mudd, the Vice-Chairman, C. Colcock Jones, presided. After an enjoyable dinner the meeting was called to order, and the first paper by Ralph Arnold on Conservation of Oil and Gas in the Americas was read by the Secretary. W. F. Staunton then read an important paper on The Influence of California Oil on the Mining Industry of the West. In this he touched upon the uses of oil as a fuel for generating power, especially in connection with the Diesel engine. This paper was discussed it some length by J. F. Mitchell-Roberts, R. B. Moran, F. H. Asbury and L. D. Godshall. The Chair then introduced Robert B. Moran of the California State Mining Bureau, Deputy Supervisor of Gas and Oil, for the' Los Angeles . District, who addressed the meeting on the work of his department. The meeting concluded with A. B. Carpenter's reading of a paper on The California Gasoline Industry by W. R.. Hamilton, Manager of the Ventura Refining Co. F. J. H. MERRILL, Secretary. ,

Jan 4, 1916

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By C. E. Berner

Since 1933, the Coal Mine Rating Schedule in Pennsylvania has provided credits in the Workmen's Compensation insurance premium rates for the use of safety hats, goggles and shoes. In that year, the worth of such protective clothing had just been well established and satisfactory articles were being made by a number of manufacturers. Standards for these three items of safety clothing' were written in the Rating Schedule and have been little changed through the years. The credit in the premium rate for a bituminous mine is $0.14 for hats, $o.08 for goggles, $o.08 for shoes. In order to earn such credit, it is necessary that all the employees in the particular mine be equipped with safety hats, goggles or shoes, as the case may be. In fact, it is not unusual for mines to qualify in all three categories, thus earning a rate reduction of $o.30 per $100 of payroll. These credits have been a decided stimulus to the use of safety clothing, and at present insured bituminous mines are credited as follows: Hats........ 63 per cent, or 22,600 employees Goggles..... 28 per cent, or 10,000 employees Shoes....... 44 per cent, or 15,800 employees Of course, many other employees wear these protective articles but they are in mines that are not fully equipped and so are not given the rate credit. The growth in use of this equipment has not been spectacular but it has been steady, as shown in Table I. An interesting thing about this is that it covers virtually all of the small and medium-sized bitumi- nous mine operations in Pennsylvania. A number of large operations are included, but many large mines are self-insured. It is difficult to keep alive interest in safety work in the smaller mines: first, because employment of safety engineers is out of the question and the one or several mine officials employed are often concerned only with production; second, because the life of many small mines is brief, so that safe conditions although established do not last long. Conditions as to safety in mines of this class rest chiefly with inspectors of state mine departments and of casualty insurance companies. Many millions of tons of production come from these mines, so that

Jan 1, 1944

By Joseph Hartshorne

The nature if this process and the general course of its development have already been described by me in two papers read before the Institute.* Since the latter paper mas read, in February, 1898, the development at Kladno has been almost altogether in the direction of using metal direct from the blast-furnace. This has now been the regular practice for about a year. The molten metal is brought from the furnace in ladles, without the intervention of any mixing- or accumulating-reservoir. The plant remains practically the same as originally described by me,† except that the primary furnace has been enlarged as much as was permitted by the existing conditions. This was done primarily in order to increase the capacity of the

Jan 1, 1901

By James P. Dr. Kimball

SULPHUR is always present in mineral coal of every variety. In the oxidized state it may exist as sulphuric acid in combination with a base. In the unoxidized state it exists in combination with iron as bisulphide of iron. It is also supposed by some chemists to exist in unknown combinations with the organic elements of the coal. This supposition requires the demonstration as a fact that certain coals yield more sulphur than what may exist in a free state, or what belongs to recognized combinations, not only with the accompanying iron but with other inorganic bases abundantly occurring in coals, but which unfortunately are very rarely estimated. This practically as well as theoretically important question it is at present impossible to decide, simply for want of available thorough ultimate coal analyses including the ash. Such analyses, at the best imperfect, are laborious and intricate, and therefore seldom made, the much simpler proximate analyses, so-called, being resorted to by most chemists for technical purposes, and commonly substituted for more scientific work even in the laboratories of government surveys. And it is unfortunate enough that few ultimate analyses are extended to the composition of the ash, much less to its relation to the original constitution of the coal. Sulphur chiefly occurs in most coals in the form of yellow pyrites (pyrite) and white pyrites (marcasite), both minerals, characterized by differences in crystalline form and in physical properties as well as in color, but having the same chemical composition (FeS2). No coal is entirely free from one or both of these dimorphous forms of bisulphide of iron. It may be disseminated through the mass so as to be invisible, in plates or scales between the laminæ of the coal, or in conspicuous segregations or nodules, sometimes of considerable dimensions. Coals greatly differ as to the proportion of sulphur which they contain. They also differ as to the relative proportion in which its several forms of combination occur. Such qualitative and quantitative disparities are scarcely, if at all, more marked in separate coal seams of a uniform type than in different parts of one and the same coal seam, whether it be considered locally as constituted of several

Jan 1, 1880

By Arthur B. Cummins

Mineral fillers are employed in United States industries to the extent of more than seven million tons annually, valued in excess of a hundred million dollars. This substantial usage involves a wide variety of mineral materials. To this may be added products manufactured from minerals, such as carbon black, portland cement, lime or chemically precipitated calcium carbonates, which would add substantially to the total. The purposes for which fillers are used differ considerably. Minerals used as fillers are mostly silicates, silicas, and carbonates as referred to hereinafter. The term "mineral filler" has various meanings in mineral technology and in the arts. Fillers are comparatively inert and their action is mainly physical. Materials that are employed primarily for chemical reactivity, or for pigment or abrasive functions ordinarily would not be considered to be fillers when used for these purposes. Nearly all filler usages are based on advantages which are gained by desired modification of composition properties or by improvements in processing. A simple definition for a filler is an inert material that is included in a composition for some useful purpose. This definition may be amplified or made more specific for each of the filler usages, the major ones of which are: paints, paper, plastics, rubber, bituminous compositions, pesticides and fertilizers. There are in addition a whole host of minor usages. Powdered minerals when employed as components in paints, varnishes and lacquers are considered as extender pigments or low refractive index pigments. In paper, the term loading material as well as filler is used; in pesticides, the terms diluents and carriers connote different functions. For bituminous compositions, rubber and plastics, the usage of the simple word "filler" is more usual, but the designation loading material is sometimes used. Minerals Used as Fillers Most of the industrial minerals, and many rock powders are employed to some extent for different filler uses. These usages vary from year to year depending on availabilities, costs, technologic trends and advancements. For the major applications, however, and for the more particular requirements at any given period, there are general trends which favor a more or less restricted group of filler products for each of the major consumer fields. This selection of materials is determined by the characteristics of the individual filler products, their effectiveness in fulfilling the primary function or functions for which they may be employed, and the cost after incorporation in the finished product. The mineral-bearing materials of major importance as fillers are: limestones, clays of several types, talc, pyrophyllite, mica, barite, diatomite, crystalline silicas, asbestos, slate and other rock dusts. Others of secondary importance include: gypsum, vermiculite, phosphate rock, perlite, and pulverized wastes, such as slag and fly ash. A considerable number of other minerals are used to lesser extent. Among these minor mineral materials are: feldspar, pumicite, wollastonite,18 tripoli, nepheline syenite,6 coal, altered volcanic rock and others.2 Indeed, most mineral materials, when reduced to fine particle size may have some potential usage as fillers, depending on their properties, availability and price. On the other hand, the more exacting filler requirements

Jan 1, 1960

By H. C. Doepken

Wrought Hadfield steel was tested in axial tension at from 100° to —196°C, to determine flow and fracture stresses as well as conventional properties. Ductility and related properties, such as fracture stress, decreased continuously with temperature. Peculiarities during straining indicated possible martensite formation or mechanical twinning. THE mechanical properties of austenitic manganese steel have been summarized by Avery and Day,' including the low temperature tensile properties reported by Hadfield and coworkers2,3 " These data show the material to be brittle at both liquid oxygen and liquid 'hydrogen temperatures. Avery and Day report considerable ductility measured by Charpy V-notch tests at —100°F (-73°C). Since the review of low temperature properties by Seigle and Brick' show face-centered cubic structures, other than Hadfield steel, to be ductile at low temperatures, it was felt that a study of tensile properties, between the reported intervals, should show whether the decrease in ductility was a gradual decline or an abrupt drop beginning at some intermediate point. X-ray examinations were made in an attempt to shed further light on the mechanism of work hardening of austenitic manganese steel. The presence of a magnetic constituent has been found by Hall" and by Avery, Homerberg, and Cook." Krivobok7 demonstrated the growth of magnetic constituents on reheating cold-worked specimens. Hadfield2,3 ' and Goss found no a iron. The steel from which the specimens were taken was commercial hot rolled % in. diam rod of electric furnace steel. The ladle analysis was as follows: C, 1.40 pct: Mn, 12.11; P, 0.060; S, 0.012; Si, 0.120; Ni, 0.080; and Cr, 0.090. Fifteen specimens, 6 in. long, were cut from a

Jan 1, 1953

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By U. Paakkinen, P. Eerola

In connection with theoretical studies of the dynamics and control of the flotation process, flotation cells and circuits at the Pyha- computer control of selective Cu - Zn - Fe sulfide flotation in the latter half of 1969. In this paper, the practical conclusions of these studies, conducted through simulation techniques, are summarized. The application of these results for control purposes implies a knowledge of the dependence of the flotation rate coefficients and the grade of concentrate on several factors, including aeration rate, froth depth, and reagent consumption. The relationships found in laboratory and plant scale tests are described. Off-line optimization studies, based on the relation- ships, are also described. The proposed steps in executing the computer control schedule are presented. In the first stage, a stabilizing control will be carried out using feed-back loops. A feed-forward control system which utilizes simple process models will also be tested. After these elementary stages, a proposed mathematical model of the circuit will be checked out and implemented with computer- run, plant-scale process tests. Off-line simulation will be continued in advance development of the control system. As a final step in the program optimal control of the process will be carried out through this model.

Jan 1, 1969

By Oswald J. Heinrich

This question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

By Oswald J. Heinrich

THIS question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

Jan 1, 1874

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite, with length-to-diameter (LID) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite), were broken in axial compression to determine to what extent an increase in end constraint increased compressive strength. Radial end constraints of 13 to 23% of the average axial stress in the pillar, produced by solid steel rings bonded with epoxy to the ends of dogbone-shaped specimens, increased compressive strength somewhat above that of cylindrical pillars without ring constraint. However, when the results were compared with those obtained by other investigators for straight specimens of several rock types taken collectively, with LID ratios greater than 0.5, the resulting strengths were not significantly different. Thus, the amount of end constraint produced by the solid steel rings was about the same as that produced by the friction from the steel end plates. In other tests, a radial prestress of 3000 or 5000 psi was applied prior to axial loading by adjustable hardened steel rings to increase the constraint above that obtained for the solid rings. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 3000 psi prestress, was 54.3% for limestone, 40.3% for marble, 44.7% for sandstone, and 23.4% for granite. The average radial constraint stress, expressed as a percentage of the average axial pillar stress at failure for the 5000 psi prestress, was 74.2% for limestone, 51.2% for marble, 61.6% for sandstone, and 29.7% for granite. These constraints increased the compressive strength significantly above the strength of straight specimens and solid-ring constrained specimens. These results suggest that large horizontal stresses in orebodies mined by the room-and-pillar method should increase the strength of the pillars and allow an increase in ore recovery by a reduction of pillar size when major structural defects are absent. One important objective of the U.S. Bureau of Mines (USBM) mining research program is the rational design of mining systems. In the design of room-and-pillar mining operations, pillar strength is a fundamental variable. It is customary to estimate this strength from uniaxial compression tests of rock samples and to correct this value for the length-to-diameter (LID) ratio of the in-situ pillar. This method of estimating pillar strength corrects for pillar shape but does not consider the effect of a large horizontal in-situ stress field that sometimes exists in underground formations. The purpose of the work covered in this report was to determine to what extent the compressive strengths of model pillars of relatively brittle rock loaded in axial compression were affected by lateral end constraint. In previous work, Obert l used solid steel rings bonded to the ends of dogbone-shaped specimens to study the creep behavior of three quasi-plastic rocks -salt, trona, and potash ore - during a test period of 1000 hr. These rings provided radial constraint during the loading cycle of 20 to 50% of the axial stress for specimens with LID ratios of 2, 0.5, and 0.25. He concluded that (1) "for a quasi-plastic material the end constraint strongly affects the specimen strength, and (2) as D/L increases (length-to-diameter decreases), the specimens lose their brittle characteristics and tend to flow rather than fracture." He also concluded that model pillars constrained by rings were better for use in predicting the strength of mine pillars than either cylindrical or prismatic specimens. This conclusion appears to be valid where mine pillars, roof, and floor are a single structural element. In the present study, 460 specimens of four relatively brittle rocks — limestone, marble, sandstone, and granite - were tested to failure. The study consisted of two parts: (1) the effect on the compressive strength of end constraint produced during the axial loading cycle by solid steel rings bonded with epoxy to the ends of the specimens, and (2) the effect on the compressive strength of increased end constraint produced in part by a prestress applied prior to axial loading and in part by lateral expansion of the specimen during the loading cycle. The first part of this study was reported in some detail earlier.2 EXPERIMENTAL PROCEDURE AND EQUIPMENT Model rock pillars of the sizes and shapes shown in Fig. 1 were broken in axial compression when the ends were constrained as shown in Fig. 2. he straight specimens were broken without ring constraint. The specimens of dogbone shape were broken with (1) solid

Jan 1, 1970

By H. M. Chance

Stretching from New York southwestwardly to Georgia is a great range of hills and mountains consisting of pre-Palæozoic schists, slates, .and gneissic and granitoid rocks, known locally by many different names; in Pennsylvania as the South mountains, the Berkshire or Durham and Reading hills, and in Virginia and farther south as the Blue ridge. To the northwest of this range lies the " Great Valley," underlain by Lower Silurian limestones, and known as the Lehigh valley, Cumberland valley, Shenandoah valley, valley of Eastern Tennessee and Georgia and by other local names, but all these are parts of one valley, geologically and geographically continuous from New Jersey to Georgia. Lying upon and along the northern flank of this range of mountains, and dipping northwestwardly under the limestone of the valley, is the Potsdam formation (Primal or No. 1 of the Pennsylvania Geological Survey), which consists of sandstone or conglomerate overlain by slates. The latter are sometimes arenaceous and occasionally are replaced in part by sandstone. This formation varies from a few feet to several hundred feet in thickness. At the outcrop the slates are completely decomposed, oxidized or disintegrated, forming a belt of clay several hundred feet wide occupying the interval between the outcroppings of the sandstone and limestone. This clay-belt includes a more or less continuous series of iron-ore (brown hematite) deposite, which have been, and still are, extensively worked. The belt is more or less continuously milleralized with iron throughout its length, and hundreds of large deposits of ore have been developed and worked, producing many millions of tons of ore.

Jan 1, 1909

By A. C. Fieldner, F. H. Gibson, W. A. Selvig

A foRmer paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance—that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in Coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determining the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein. Testing Formulas with Float-and-sink Separations The former paper by Fieldner and Selvig gave heat values of pure coal of the float-and-sink portions of 21 coals, as calculated by the Parr formula

Jan 1, 1932

By C. H. Li, J. A. Sarteli, W. Bonfield

The stress to cause a permanent micros train of 2 x 10-6 in. per in. (defined as the microscopic yield stress) in beryllium is found to be very sensitive to surface condition. The initiation of plastic flow in as-machined specimens, which contain a high density of twins and large residual compressive stresses to a depth of about 0.010 in. from the surface, occurs by the nucleation of slip from high stress fields around twin tips in the surface layers. Removal of the damaged surface layers by chemical polishing results in an appreciable increase in the microscopic yield stress, which is attributed to the remoual of stress raising twins rather than to the release of residual stresses. IT is well known that the macroscopic mechanical properties of beryllium are very sensitive to the nature of its surface finish. Matthews and coworkers1 have shown that the tensile strength of rolled beryllium sheet can be considerably enhanced by chemical polishing, presumably due to the removal of the high concentration of notches, twins, and large residual compressive stresses normally found in the surface layers of ground specimens. There was no similar effect of surface condition on the macroscopic yield stress (the stress to produce 0.2 pct strain), a point to which we shall return. To date there have been no extensive studies on the effect of surface condition on the microstrain region of beryllium. Recent measurements2 of the stress to cause a permanent microstrain of the order of 10-6 in. per in. on machined hot pressed QMV beryllium, gave values ranging from about 600 to 3500 psi. Reasons for the considerable scatter in the results were not discussed. In this paper, we wish to show that the microstrain region of polycrystalline beryllium is, in fact, very sensitive to surface condition. The stress to cause a permanent strain of 2 x 10-6 in. per in. which for convenience we will refer to as the microscopic yield stress, can be increased by almost a factor of 2 by minimizing the amount of surface damage. The variation of microscopic yield stress is attributed to the presence of twins in the surface layers, rather than to residual compressive stresses. EXPERIMENTAL PROCEDURE The starting material for this investigation was commercial purity hot pressed QMV beryllium, with an average grain size of about 20 . The effects of surface treatment were assessed by comparing the microstructure with residual stress measurements and microstrain properties. Specimens were prepared for metallographic examination by wet grinding with 240, 400, and 600 papers, followed by polishing with a suspension of fine alumina in warm 20 pct oxalic acid. After this treatment, the surface could be examined, either in the unetched condition with polarized light, or after etching in 2 pct hydrofluoric or boiling 20 pct oxalic acid with normal light. Thin films of beryllium suitable for electron transmission study were prepared from bulk specimens by chemical polishing with hydrofluoric and phosphoric acids, and were examined in an RCA-EMU-3 electron microscope. Residual stress measurements were made by a procedure similar to that of Treuting and Read.3 Specimens 4.0 in. by 0.625 in. by 0.080 in. were prepared by three different machining procedures, namely: turning, grinding, and sawing, in order to introduce different levels of residual stresses. An electrical resistance strain gage was attached to one side of the specimen, and that surface was then protected by an acid-resistant enamel, while the opposite surface was removed by etching approximately one thousandth of an inch at a time. The change in specimen curvature in the longitudinal direction was noted and the residual stress was calculated by the following formula:

Jan 1, 1963

By F. G. Tahmoush, N. J. Grant, E. P. Abrahamson

The effect of grain size on the brittle -ductile transition temperature of pure iron and three dilute Fe-W alloys has been investigated by slow bend tests. The brittle-ductile transition temperature for pure iron increased with increasing grain sizes from 8000 to 500 grains per sq mm where the transition temperature then decreased with further increase in grain size. The dilute additions of tungsten lowered the transition temperature for fine grain sizes, suppressed a reversal of the curve in the coarse grained portion, and raised the transition temperature for this region. The frequency of twin occurrence increased with increasing grain size and decreasing temperature. The object of the present investigation was to re-examine the effect of grain size on the brittle -ductile transition of pure iron and several dilute Fe-W alloys. Current literature normally presents a simple relationship between grain size and the brittle-ductile transition temperature, namely, that the transition temperature increases with increasing grain size. Heslop and etch' have studied the transition temperature of mild steel by V-notch Charpy impact tests for the grain size range between 200 and 6000 grains per sq mm. The result was a linear plot of In 1-1/2 vs brittle-ductile transition temperature, where 1 is the grain diameter. Recent experiments by sipos2 revealed the possibility of a reversal in the slope of the grain size vs transition temperature plot for pure iron; however, his investigation was limited in scope, and the data obtained were insufficient to permit a definitive curve. The present investigation was undertaken in an effort to confirm or extend the grain size effect observed in iron by Sipos. PROCEDURE All alloys were vacuum induction melted, using 99.95 pct Fe containing 0.03 pct 0 and 0.004 pct C. Four ingots were made, ranging from pure iron to iron with 0.035 pct W. The chemical composition of each alloy, after processing, is given in Table I. The four alloys were prepared as 45 lb heats and cast into 4 in. diam by 16 in. molds. They were then extruded into 3/4 in. rods at 1800oF. Specimens for chemical analysis, taken from various positions along the rods, revealed no variation in tungsten content along the length. The extruded rods were reduced to 0.156 in. diam stock by a series of cold swaging operations involving intermediate vacuum annealing treatments. This procedure yielded a final cold reduction in area ranging from 10 to 90 pct. The swaged rods were chemically cleaned, cold pressed to a cross section of 0.10 by 0.18 by 1.0 in. long (2.54 by 4.73 by 25 mm). The specimens were wrapped in iron foil and vacuum sealed (10-4 mm Hg) in quartz. Various heat treatments at temperatures from 700" to 1300oC were utilized to produce grain sizes from 8000 to 1 grain per sq mm. Grain sizes were determined by measuring the average area of grains in a polished section. In specimens with grain size greater than 20 grains per sq mm, the total number of grains in the cross section was counted and then divided by the area to yield grains per sq mm. Grain size was measured both for longitudinal and transverse cross sections. The average of the two measurements was plotted vs transition temperature. An Instron Table Model testing machine was used to determine the transition temperature of specimens tested in three point horizontal bending. The specimen was supported by two 1/4 in. dowels one in. apart. Bending was accomplished with a push rod, the end of which had an 1/8 in. radius. The head speed was 50 in. per min. Temperatures were established through the use

Jan 1, 1963

The authors of T.P. 4179 have conducted a large number of experimental water floods, and the data are reported in a very clear manner. These data show significant variations of residual oil saturation with changes in wettability, interfacial tension, flooding rate, and oil-water viscosity ratio. Furthermore, some of the data obtained cover a range of variables not previously reported in the literature. It is our opinion that at least some of the observed variation in oil recovery can be obtained only in floods made under conditions identical with those used by the authors. There are other systems which may be said to have the same wettability, but which exhibit an entirely different qualitative dependence of oil recovery on the experimental variables. In this regard, we would like to direct attention to several items which we feel are not given sufficient consideration in the paper. The first of these items has to do with wetting equilibrium. A survey of the current literature will reveal that little is known, and even less is understood, about wetting equilibrium. This is particularly true of the relation between contact angle measurements made under static conditions, and the wettability existing under the dynamic conditions of floods carried out at relatively high rates. We feel that this is a very important consideration, particularly in the floods the authors performed under what they consider to be "water-wet" conditions. It is our opinion that wetting equilibrium did not exist in these floods, except possibly at the very lowest rates. This opinion is in part based on some flooding tests we have made which are very similar to some of those described by the authors. These floods were made in unconsolidated cores, 6 in. long and 13/4 in. in diameter, made up of carefully graded glass spheres of the approximate size of the sand grains used in the subject paper. The cores were mounted vertically, and distilled water was used to displace a refined oil equivalent to the authors Soltrol C. The glass spheres had previously been carefully cleaned so that they were strongly wet by the water. The floods were made with and without an interstitial water saturation. When interstitial water was present, the solid surfaces were mostly covered with water prior to injecting the flooding phase. Consequently, a condition very near wetting equilibrium existed throughout the flood. The data in Fig. A show that under these eircumstances, rate had no influence on residual oil at flood-out, over the range of rates studied. On the other hand, in the absence of interstitial water, the surfaces are all covered with oil before the displacement. To achieve wetting equilibrium the injected water must displace the oil from the surfaces themselves. This is not a fast process. Therefore, the effective dynamic wetting condition in floods of this type must depend upon the flooding rate. When the flood rate is very low, compared to the rate at which wetting equilibrium is attained, the residual oil saturation at flood-out is essentially the same as the residual obtained when interstitial water is present. This is shown in Fig. A, and occurs because the dynamic wetting conditions are the same in both cases. However, at moderately high flooding rates, the rate has an important bearing on the amount of oil recovered because in this case the attainment of surface equilibrium is the slow step. We believe that, in the absence of an interstitial water saturation, oil recovery varies with rate because of the reasonably slow approach to wetting equilibrium which occurs during the displacement. In fact, as the rate is increased, the oil recovery performance indicates the core is becoming progressively less water-wet. At the highest rate there is even considerable simultaneous production of oil and water after breakthrough. This does not occur at the lower flooding rates, nor is there appreciable simultaneous oil and water produc-

Jan 1, 1957

By Juptner von Jonstorff

A discussion of the paper by Messrs. Jüptner von Jonstorff, Blair, Dillner and Stead, read by title at the Lake Superior meeting, but presented first at the New York meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement between the two Institutes. Correspondence. MR. R. HAMILTON (Glengarnock) wrote to say that it was known for many years, that unless certain precautions were taken in dissolving the sample, there was a liability to obtain a solution from which the ammonium-molybdate solution would not precipitate the whole of the phosphorus. In 1877 Blair and Finkiner independently attributed this interference to the presence of carbonaceous matter in the solution, derived from the action of acids on the combined carbon of the metal, and they directed that the solution should be prepared in such a manner as to destroy these carbonaceous compounds. This was practically effected by evaporating the acid solution to dryness and roasting the residue. Adolf Tamm, in 1884, accentuated the same view. There are methods founded on the above-mentioned observations which leave nothing to be desired in point of accuracy, but the evaporation to dryness with subsequent roasting and re-solution consumes much time, besides the minor inconvenience caused by large amounts of acid fumes. In 1888 P. W. Shinier suggested that the incomplete precipitation of phosphorus was due to incomplete oxidation of -.the phosphorus, and proposed to render all the phosphorus precipitable by oxidizing the solution with potassium permanganate, etc. Experiments were made to test the accuracy of this view (details will be found in the Journal of the Society of Chemical Industry, vol. x., p. 904), and the results obtained seem to-prove that it is the correct one. It was first proved that carbonaceous matter in solution did not prevent the precipitation of properly oxidized phosphorus

Mar 1, 1905