Search Documents

By L. J. Trilli

RECENT studies have indicated that there may be considerable difference in the cleanliness of the central pipe cavity of open top ingots. It has been speculated that some of this difference arises becausk of reactions that occur during reheating in the blooming mill soaking pits. In this respect, it has been recognized that an oxide coating or flow of slaggy material in the cavity could inhibit welding during hot rolling and thus reduce the amount of sound product which may be obtained. This note is intended to summarize some observations on the structure of a split ingot top which may be useful in describing a mechanism whereby the shrinkage cavity could be oxidized during reheating. A 221/2x241/2 in., big-end-down, test ingot was secured from a routine production heat. The chemical analysis representing this ingot is as follows: 0.08 pct C, 1.04 pct Mn, 0.062 pct P, 0.315 pct S, and 0.02 pct Si. The deoxidation practice used on the heat from which the experimental ingot was

Jan 1, 1957

By C. Norman Cochran

The pllnse diagvam for the NaF-AlF3 system was used to calcutate an ionic model for the NaF-AlF3 system. Assuming an ideal solution,a series of simultaneous equations expressing equilibria be-tween solid and liquid phases at the euleclic, perilec-tic, and melting points were solved for the activities of the ionic species, the dissociation constants, and the entropies and heats of fusion. The calculations suggest the existence of A13F1415 ions in addition to the F-1+AlF6-3 , and AlF4-4 ions previously proposed by others. The calculaled valnes give better agreement with vapor pressures than the previous model without Al3Fl14-5. Additional possible vefinements of the model are proposed. CRYOSCOPIC1 investigations and density data2 for the NaF-A1F3 system have previously been used to study the dissociation mechanism of Na3A1F6 and to derive equilibrium constants for its dissociation to NaF and NaAlF,. Depending primarily on the heat of fusion assumed for cryolite, the dissociation constants ranged between 0.02 and 0.18 from cryoscopic studies, and from 0.09 at 1273°K to 0.16 at 1363°K from density data. In most cases the values were unable to reproduce satisfactorily the experimental liquidus lines very far on the A1F3 side of the Na3A1Fe composition. This suggested the existence of at least one other ionized compound in the melt besides NaA1F4 in the Na3A1F6-A1F3 side of the system. This is assumed to be liquid Na&13F14 (chiolite), which is already established as a stable solid in phase studies of this system. MODEL FOR THE MELT The melt is assumed to be an ideal solution with ion activities equal to anion fractions. The only cation in the model is sodium so that Temkin and simple anionic activities are identical. Although the compounds are completely ionized to Na' and the respective anion in the melt, molecular rather than ionic notation is used throughout this work. The Na3A1Fe is assumed to dissociate to NaA1F4 and NaF as in the former model, and Na&13F14 to dissociate to Na3A1Fe and NaA1F4. Other valid dissociation equilibria can be written involving these four compounds, but all of these can be obtained by combinations of the two described dissociation reactions and, thus, are automatically considered in these calculations. The model allows for no free AlF3 so that compositions for NAIF3 > 0.5 (mole fraction A1F3 on the NaF-A1F3 basis) cannot be treated. The question of the existence of free AlF3 in the melt will be discussed again later. The constants in the model were evaluated from points along the entire known liquidus line of the NaF-A1F3 system. Previous work employed only the liquidus line or densi- ties near the Na3A1F, composition. The liquidus line compositions used in the solution of the model are from unpublished work by Mr. P. A. Foster, Jr., for compositions between the Na3A1F6 melting point and the Na&13F14-A1F3 eutectic, and from the published works of Grjotheim,1 Phillips,3 and Foster4 for the remainder of the system. The relationships used in solving for the desired dissociation constants and heats and entropies of fusion are listed in Table I, and the points along the liquidus line at which each apply are indicated to the right of the relationships. The mole fractions of each of the separate species in the melt are symbolized by N. Relationships [I] and [2] are the respective dissocia-ation constants, Kl and K2, of Na3AIF6 and Na5A13F14 for this model. For simplicity, these constants will be assumed to be independent of temperature. Relationship [3] follows from the assumption of the ideal solution. The expression relating the values of N to the experimental values of NAIf3, is given in Relationship (41. Relationships [5], [6], and [7] each state the equilibrium between a compound in the melt and its pure solid phase for the portion of the liquidus lines where it precipitates. The heats of melting, AH,, and entropies of melting, AS,, used in [5], [6], and [7] are assumed to be independent of temperature. The compositions and temperatures of all five invariant points (two melting points, two eutectics, and one peritectic) along the liquidus lines from NAIF3 = 0 to NAIF3 = 0.5 were employed in the solution. The eutectic and peritectic compositions were particularly useful because each of these is involved in one more equation than other points along the liquidus lines and thus reduces the number of points required to solve for the constants. Also, their use assures that the inflection points in the derived liquidus line will correspond exactly with those on the experimental liquidus line. The total number of equations is 5k1 — 1, where n is the number of experimental composition points used. The number of unknowns is 4n + 5 (4n- 3 values of N, 3 values each of AH, and AS,, and 2 values of K). Thus, six points must be used in the solution to obtain an equal number of equations and unknowns. The one additional required experimental composition was taken on the liquidus line between the Na3A1Fe melting point and the Na3A1F6-Na5A13F14 peritectic. Previous work indicated this was a difficult portion of the curve to fit. The temperature used for the point was 1161°K, the same as for the NaF-Na3A1Fe eutectic. This choice of temperature gave two points with identical NNa3AIF6 values which simplifies the algebraic solution. The second point at this temperature is denoted 1161°'K. PROCEDURE FOR SOLUTION OF EQUATIONS Values were assumed for NNa,AIF and NNaF at the NaF-Na3A1F6 eutectic at 1161°k. By an iterative procedure, the corresponding values for NNa5A13F14 and NNaAlF4 at 1161°K were determined from 131 and 141. A value was assumed for NNaAlF4 at 1161°'K and

Jan 1, 1968

By C. A. Doh, R. Q. Fields, M. Lebourg

A formation tester run on logging cable is now available to the oil industry. It offers a method of safely and rapidly testing possible producing formations in uncased holes. These tests can be made up the hole after running the electric log. Reservoir pressure data is continuously recorded at the surface as the fluid sample is extracted. The tester may be assembled with a reservoir of 1-, 2.75-, or 5.5-gal capacity. A retaining pad on the body of the tool is expanded against the wall of the hole at the exact depth desired; this depth is determined by electrical log control. Two bullets are then fired through the center of the retaining pad which create a connection between the formation and a flow line to the sample chamber. When the chamber is filled, a valve is closed and the fluid sample sealed at maximum pressure. The tool is retracted to minimum diameter and brought out of the hole. Electrical circuits permit a complete recording at the surface of the mechanical operations of the tool as well as the formation pressure build-up and the hydrostatic mud pressure. The tool was introduced commercially during the latter part of 1955 in the Gulf Coasts of Louisiana and Texas. Over 1,000 operations have been made to date (Sept. 1, 1956); 50 per cent of which resulted in successful tests. Failures have been due mostly to ineffective sealing in unconsolidated sands. One major company had 41 successful tests out of 80 attempts with 23 ineffective pad seals. Results for this company were very gratifying as to pinpointing gas-oil ratios, indicating productive permeabilities and aiding in determination of fluid content where electrical log and side-wall coring information were inconclusive. Eight typical pressure curves are discussed (including misruns). Six types of fluid recoveries are interpreted. Eight actual field examples of electric logs, showing the problems solved by the formation tester, are illustrated. The present applications of the tool are discussed: 1. Determination of productive fluid—varticularlv differentiating between gas and oil. 2. Determination of reservoir pressure as an aid to: (a) safety in completion technique, (b) reduction in drilling costs, and (c) reservoir analysis. 3. Determination of minimum gas-oil ratios. 4. Location of gas-oil or oil-water contacts. 5. Recovery of samples for examination and analysis: oil (gravity); gas (hydrocarbon content); water (salinity). Additional applications envisioned for the future are also given: (I) subsurface exploration based on accurate pressure, (2) recovery of fluid samples from the undisturbed reservoir for PVT work, and (3) possible quantitative study of permeabilities or productivity index. Running the formation tester requires no special pre-cautionary measures. Because full hydrostatic mud pressure is maintained at all times, well depth is no problem. Thus, the method allows safe, economical testing in wells which heretofore could only be tested by setting casing. INTRODUCTION A new method of safely and rapidly testing possible producing formations in uncased holes is achieving considerable success. The method offers promise of further advances in reservoir study. Called the formation tester, the new instrument is unique in that it operates on logging cable. It thus offers all the advantages of wire-line operations and becomes an important adjunct to present logging and side-wall coring services. The tester is operated against the wall of the hole at any depth desired. Zones to be tested are usually determined by a study of the electrical and the micro-caliper surveys. Reservoir data, as well as the operating cycle of the tool in the hole, are continuously recorded at the surface during the operation. The tester, as it was originally designed, was capable of recovering a 1-gal sample of reservoir fluid per trip in the hole. Tools with reservoirs of 2.75- and 5.5-gal capacity are now available. The 5.5-gal reservoir is equipped with a segregating system, set before going in the hole, so that the last portion of the recovery (usually 1 gal) is automatically separated from the first portion. This makes it possible

Jan 1, 1958

By J. A. Coll, R. W. Cahn, A. Lawley

WHILE the creep properties of pure face-centered-cubic and close-packed-hexagonal metals have been thoroughly investigated and are well established, body-centered-cubic metals have been studied less extensively. Moreover, very few fundamental studies on the creep of solid solutions, irrespective of crystal structure, have been reported. The present study is concerned with the creep of a series of body-centered-cubic solid solutions. The present position concerning creep of pure metals is, briefly, as follows.1"3 Creep at first takes place at a steadily decreasing rate; this is the stage termed primary or transient creep. Except at the lowest temperatures this is succeeded by a stage of secondary or steady-state creep. At high temperatures and stresses, this may be succeeded by an accelerating stage, termed tertiary creep, with which we shall not here be concerned. There is no well-defined physical model at present for the transient stage; in general terms, transient creep is best regarded simply as a manifestation of work-harden ing. Steady-stage creep can certainly take place by several different mechanisms: the choice of dominant mechanism depends primarily on temperature. We shall here be concerned only with high-temperature steady-state creep, a term usually reserved for creep at absolute temperatures higher than 0.5 Tm, where T, is the melting point. In this range, the activation energy for creep is, for many metals, equal to the activation energy for self-diffusion, and this is generally interpreted in terms of a "climb mechanism.1-4 The creep rate is determined by the speed at which dislocations, impeded by obstacles the nature of which is disputed but which are probably established during transient creep, can climb by means of a diffusion process, until they are able to by-pass the obstacle. In solid solutions, the intrinsic resistance to the slip motion of dislocations may be much larger than in the solvent, to the extent that the motion of dislocations in the glide plane, rather than their escape by climb out of this plane, may become the rate-controlling factor. weertman5 has considered this possibility from a theoretical point of view, and concluded that some form of "viscous slip" is likely to be rate-controlling at comparatively low stresses. The resistance to slip may arise from "atmospheres" of impurities forming around dislocations; a high Peierls force in materials of high cohesion; or some structural peculiarity such as clustering or ordering of solute atoms.= We shall be concerned here with the case of ordering. The only published investigations concerned explicitly with the effect of order on creep refer to creep in ß-brass by Herman and Brown,7 and in Ni-Fe alloys, by Kornilov and panasyuk8 and by Suzuki and Yamamoto.9 Recently, Herman and Brown's paper has been supplemented by a determination of the tensile yield point of ß-brass as a function of temperature.10 Both studies showed a sharp drop in resistance to deformation of ß-brass over a range of a few degrees just above the critical temperature Tc at which order finally disappears. These observations are especially noteworthy, because in ß brass the degree of order diminishes steadzly to zero as the temperature approaches Tc. It is, therefore, the disappearance of the last traces of long-range order which has the largest effect on the resistance of the alloy to plastic deformation. In the Ni/Fe alloys of various compositions, resistance to creep at a given temperature and stress is maximum at the stoichiometric composition, both below Tc, (long-range order), and above T,. (short-range order).' Near Tc, the creep resistance of an ordered alloy is much higher than that of the same alloy in the disordered condition.9 The aim of the present investigation was to study the creep behavior in the neighborhood of Tc, of another system of ordering alloys. The iron-aluminum alloys were considered the most suitable. because: i) The order again diminishes steadily to zero as the temperature approaches Tc; there is no sudden drop in order at Tc, and it therefore is

Jan 1, 1961

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By Fritz Wald, Martin Weinstein, Herbert E. Bates

ONE of the methods for preparing a fiber-reinforced composite is that of directional solidification of a eutectic melt. Its major drawback lies in the fact that the matrix in this case is a pure constituent (or a terminal solid solution of fixed concentration) and the ratio of fiber to matrix volume is fixed. Only very few, if any, pure metal matrices possess technically useful properties, and the necessity for alloying is the inevitable consequence of this fact. Nevertheless, structures similar to binary eutectic ones can be obtained in higher-order systems by pseudoeutectic reactions of a type where crystallites and a solid-solution matrix are simultaneously precipitated from a liquid.1"3 Trials to solidify such alloys directionally—the matrix consisting of a solid solution of chromium, nickel, and silicon and the reinforcing phase being Cr3C2— will be reported elsewhere.4 This note describes constitutional studies carried out primarily to determine -the position of the pseudoeutectic and further to insure that no undesirable reactions between the reinforcing phase and components of the matrix occur in the solid state at elevated temperatures. In the investigation it was specifically desired to reinforce a matrix which is as close as possible to the 80/20 Nichrome composition with Cr3C2 to insure good oxidation resistance and improve the strength at high temperatures. No konstitutional information on the quaternary C-Cr-Ni-Si svstem in the range of interest was found in the literature. Nevertheless, the two most important ternaries c-cr-Ni5 and have been completely investigated. On C-Cr-Si some investigations have been conducted,7"9 and C-Ni-Si was studied with a few alloys in the course of the present investination 9 Eight alloys were prepared to investigate the changes in the constitution of the ternary C-Cr3Ce-yNi eutectic5 with silicon contents up to 10 wt pct. Five alloys were made with varying chromium and carbon contents around compositions containing -60 to 70 wt pct Ni and 5 to 6 wt pct Si. The latter alloys were designed to locate the y(Ni-Cr-Si-C)-Cr3C2 pseudoeutectic reaction and to determine the maximum chromium content in solid solution compatible with a two-phase equilibrium between y and Cr3C2 only. The alloys were prepared from electrolyte nickel, semiconductor-grade silicon, high-purity chromium (99.999 pct pellets), and semiconductor-grade graphite. They were melted inductively in high-purity alumina crucibles under flowing argon. Twenty-gram charges were prepared and investigated by optical microscopy (including hot-stage investigations), X-ray powder methods, and electronmicroprobe analysis. The alloys were studied in the as-cast condition and also after a homogenization annealing treatment of 48 days at 900°C in evacuated quartz ampoules. The structures of all alloys based on the ternary eutectic plus silicon in the as-cast state consisted generally of an inhomogeneous solid solution and at least two other phases. Annealing of the alloys showed that the solid solution was homogenized but that an incomplete solid-state reaction had taken place in all alloys with silicon contents over 5 wt pct. This reaction is clearly visible in Fig. 1 around the large Cr3C2 crystals (gray areas). Below this concentration, the alloys consisted of a homogeneous matrix and precipitates of Cr3C2 plus graphite, Fig. 2. The Cr3C2 was entirely unreacted here. From these observations and subsequent X-ray and microprobe investigations, it was deduced that the

Jan 1, 1969

By Per Larsson

The Chapin Mine, on the Menominee range, Lake Superior, was first opened in 1880 and has since then produced 1 1/2 million tons of soft blue hematite, containing about 63 per cent. of iron and 0.07 per cent. of phosphorus. Up to the present time, the ore has been mined from three separate lenticular deposits, which conform with the Huronian strata of the district, striking N. 75' W., dipping from 70' to 80' N., and pitching about 30' W. The largest of these ore-bodies has a horizontal length of 2500 feet, and a maximum width of 130 feet in the middle, from which it gradually narrows to the pointed ends. Its dimensions have not changed materially as greater depth has been attained. Figs. 1 and 2 show the geology and the mine-workings on the main deposit.. As this main deposit pitches away from the eastern part of the property, it is replaced by another lens, containing ore of the same quality. When first opened on the 1st level, this lens was 150 feet long and up to 50 feet wide, while now on the 6th level it shows a length of 550 feet, and a maximum width of 100 feet. It is separated from the extreme east end of the main deposit by about 30 feet of clay-slates It pinches out gradually between the slates to the west, and stops abruptly against the jasper to the east. Farther east in this belt of jasper occurs the third ore-lens which has a pretty regular length of 100 feet and averages, from the 1st to the 5th level, 20 feet in width. A cross-section of the ore-formation shows, on the north or hanging side of the ore, about 200 feet of clay-slates, and farther north a heavy belt of magnesian limestone. The slates and the dolomite are generally separated near the surface by a conglomerate of broken dolomite and soft slates. The foot-wall rock is also a clay-slate, containing a higher percentage of iron and less magnesia than the hanging-slate. Farther south occur alternate beds of slates and lean ore or jasper.

Jan 1, 1888

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth's crust.

Jan 5, 1974

By T. J. Whalen, S. M. Kaufman

Surface-tension measurements for liquid Fe-C-Co and Fe-C-Ni alloys were performed by the sesszle-drop technique at 1350o and 1425°C. Cobalt was shown to he more effective than nickel in lowering the surface tension of Fe-C alloys A minimum value for surface tension of 1640 dynes per cm was found in the Fe-C-Co system at a concentration of 1.5 pet C and 12pet Co. Analysis of these measurements in terms of adsorption and desorption behavior indicated that cobalt and nickel lower surface tension in Fe-C alloys by replacing carbon at the liquid-vapor interface. Comparison of results to date for Fe-C liquid alloys has shown that most substitutional-type elements having about the same atomic diameter as iron also have relatively the same influence on surface tension when present in dilute amounts. It has been shown previously that surface-adsorption behavior in liquid Fe-C ternary alloys is related to the manner in which the ternary addition affects the activity of carbon in the bulk solution.' Certain ternary additions, such as chromium, tending to decrease carbon activity cause adsorption of carbon and chromium to the liquid-vapor interface. Additions, such as silicon, increase the carbon activity, resulting in a desorption of carbon and an adsorption of silicon. Both cases were shown to cause a decrease in surface tension due to adsorption. It is the object of this paper, as part of the writers' continuing interest in the effect of alloying additions on the surface tension of Fe-C alloys, to present and discuss surface-tension data on solutions in the ternary systems Fe-C-Co and Fe-C-Ni. Available activity measurements for these systems in the solid state indicate a strong increase in carbon activity when either nickel or cobalt is added to Fe-C alloys.2, 3 EXPERIMENTAL PROCEDURE The alloy compositions used are shown in Table I. These alloys were prepared by vacuum melting in stabilized zirconia crucibles and then vacuum casting into cold-steel molds. The nominal analyses for the alloys used in this investigation are given in Table I. Surface tensions and densities were measured by the sessile-drop method4,5 in conjunction with the tables of Bashforth and bdams.' Specimens were prepared by slicing 1/4-in. cubes from the center of the vacuum-cast ingots and grinding the edges of these cubes until their shapes approximated spheres with flat bottoms. Proper handling techniques, including an acetone rinse immediately before use, assured minimum contamination from sources extraneous to the actual melting. For each experimental run a sample was placed on a BeO plaque and positioned and leveled inside a vacuum induction heating apparatus. The sample and plaque arrangement sat inside a molybdenum tube which acted as the susceptor. Diagrams of this apparatus may be found in the literature.= After heating to temperatures just above the liquidus at pressures of the order of 10-4 to 10- 5 mm Hg, photographs of the drop profile were made using its natural thermal radiation as a light source. Some measurements were made with partial pressures (-1 cm Hg) of a mixture of H2 and He gases. The H2-He atmospheres proved to be necessary at higher nickel contents to retard excessive vaporization losses. Chemical analysis for carbon and the ternary addition was performed for each alloy sample after completion of the experimental run.

Jan 1, 1964

By R. E. Collins, Paul B. Crawford

Potentiometric model studies have been made of ertically fractured reservoirs. All fractures originated at he well and extended into the reservoir for various distances. Studies were made to determine the areal sweep efficiencies for line-drive patterns. The areal sweep efficiency for the unfractured system studied war 70.6 per cent. It was found that if the vertical fracture war paralIel with the direction of flood, the areal sweep efficiency may be considerably reduced, approaching zero in some instances. If the fracture was at right angles to the direction of flood, the areal sweep efficiency may be greater than that for the unfractured system. The sweep efficiency depends on the length and orientation of the fracture and direction of the flood. It is concluded that considerable effort should be made to determine the nature and direction of fractures before initiating a flooding program. Such information is required if the maximum sweep efficiency is to be obtained and channeling is to be reduced to a minimum. INTRODUCTION The recent development and application of fracturing techniques to petroleum reservoirs has served to focus considerable attention on the effect such fractures may have on secondary oil recoveries. The opinion has been expressed that fracturing may not alter appreciably the water flooding possibilities. Others have thought that channeling may occur and that the creation of fractures may serve to substantially reduce the possibilities of conducting a successful water flood in the reservoir The purpose of this study was to obtain quantitative estimates of the effect of vertical fractures on the areal sweep efficiencies of line-drive flooding patterns. In presenting this work on vertical fractures, it is not to be inferred that the present fracturing techniques result in producing a vertical fracture. The types of fracture which are created are not known with certainty in every case. Some are believed to be horizontal, others inclined along bedding planes, and some data indicate vertical fracturing. Each fracture will probably exert a different influence on the sweep efficiency of the secondary recovery program; consequently each fractured well should perhaps be considered as a separate problem, requiring a careful analysis. Preliminary work on the effect of fractures on producing capacity of a well indicated that for practical purposes many fractures may be treated as having a nearly infinite permeability This assumption appears to be valid in some instances where the permeability of the fracture is only 10 or 100 times greater than the permeability of the matrix. It is known to depend on the type, orientation and length of the fracture. In realization that fractures of only 0.01 in. width have calculated permeabilities near 5,000 darcys, it is believed that many fractures may be considered as of near infinite permeability without incurring serious error. Primarily for this reason this study was made with fracture analogs of very great permeability compared to the matrix. FRACTURED SYSTEM ANALOG The pattern sweep efficiencies reported here were obtained with the aid of a potentiometric model. The application of this type model for solving reservoir problems has been described in the literature.1,2,3 The electrolyte reservoir was 20 in. wide by 30 in. long by approximately % in. deep. The liquid depth was constant, which corresponded to a constant permeability-feet product from the injection to the production well. The electrolyte reservoir was built to correspond to a unit in the line-drive pattern shown in Fig. 1. This figure shows part of an infinite array of wells having alternate rows of fractured and unfractured wells. The area within the dashed rectangle shows the area generally studied in the model. In using the model to represent a fractured system, a thin strip of copper was soldered to the well or wells and the length and orientation of the strip was made to conform to the vertical fracture under consideration.

Jan 1, 1955

By Charles Wright

AT most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bull-dozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1935

By P. E. Arnold, G. S. Ansell

RELAXATION in metals has been studied in detail by many workers in recent years.1-5 These studies have shown that there is an energy-loss peak observed in a metal placed in mechanical resonance at low frequencies which may be correlated with various metallurgical processes. These experiments have been largely used to study single-phase materials. In order to study the effect of a finely dispersed second phase in a metal matrix upon this phenomenon, the relaxation behavior of an aluminum-aluminum oxide SAP-Type alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions was investigated by the use of internal-friction measurements. The alloys studied, designated MD 2100, consist of a matrix of commercial-purity aluminum containing a finely dispersed second phase of aluminum oxide. The aluminum oxide is present in this alloy in the form of fine platelets approximately 130A units thick and several microns on edge. The mean free path betwen dispersed platelets is approximately 0.5 p. The grain size of this alloy is extremely stable at temperatures as high as the melting temperature of the aluminum matrix. In the as-extruded condition the grain diameter is several microns, while in the recrystallized condition it is several millimeters in diameter. The damping characteristics of the alloy samples were determined using a torsional-pendulum device. The internal-friction constant was determined for this alloy in both the fine-grained as-extruded and coarse-grained recrystallized conditions over the temperature range from 343" to 923°K at frequencies of 0.9, 1.3, and 1.8 cycles per sec. An internal-friction peak was observed in testing the fine-grained alloys which was not observed for the coarse-grained alloys. This peak, which might be associated with a type of grain-boundary relaxation, was observed at each of the three different test frequencies for the fine-grained sample. The temperature at which the relaxation peak occurred for each of the three different frequencies is shown in Table I. From these data an activation energy of relaxation for each pair of frequencies was determined by comparing the temperature shift of the relaxation peak with frequency between each of the test frequencies, assuming that an Arrhenius-type rate equation is applicable. The activation energy of relaxation determined from these data is also shown in Table I. The mean value of the activation energy was about 6 kcal per mole. The activation energy for the relaxation process determined in this investigation indicates that the relaxation associated with the grain boundaries in this aluminum-aluminum oxide SAP-Type alloy is quite a different process than grain boundary relaxation in single-phase aluminum alloys. In these latter alloys, the activation energy for relaxation has been found to be the activation energy for self-diffusion, approximately 36 kcal per mole1,2 Where the activation energy is the same as the activation energy for self diffusion, it has been proposed that the relaxation phenomena is dependent upon vacancy formation and motion. It is apparent therefore, that, in this aluminum-aluminum oxide SAP-Type alloy, the relaxation must be due to another type of atom transport. It has been shown previously in studies of the high-temperature, low-stress, steady-state creep behavior of as-extruded aluminum SAP-Type alloys, that the activation energy for steady-state creep is one that may be characterized by the nucleation of dislocations from the grain boundaries. It is proposed that the relaxation behavior observed here is due to a similar effect. In this case, the internal-friction peak is a resonance behavior due to the time-dependent nucleation of dislocations from grain boundaries in the sample. A process of this type would have an activation energy which is undoubtedly stress-dependent and of the form Q = Q, + (dQ/du)u

Jan 1, 1962

By C. S. Chang

Replacement of active groups in corn starch, as shown by results of the starch derivatives tested, impairs rather than improves the value of corn starch as a selective iron oxide depressant. Increased ability to depress iron oxides is generally accompanied by a parallel ability to depress quartz. PEARL starch, a corn starch prepared with a minimum of alteration, is a good selective depressant for iron oxide minerals.' From what is known of the complex chemistry of corn starch, there is evidence that it consists of a mixture of saturated giant polymeric molecules, both straight and branch-chained, the constituents consisting of glucose units with hydroxyl radicals as active or polar groups. To add to the existing knowledge of the chemistry of the flotation process, it is desirable to ascertain the effects on the corn starch as an iron oxide depres-

Jan 1, 1955

By J. L. Jernegan

In this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two windfurnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

By J. L. Jernegan

IN this paper I propose to give a short and, I must confess, a rather incomplete description, as regards many details, of the process used in Chicago, Ill., for smelting the argentiferous ores of the far West, and shall confine myself in this description, principally, to the process used at the Chicago Silver Smelting and Refining Company's Works, known as the Balbach process, as all the other smelting works in that city follow the same method, with the exception of one, which has the Cordurié, process for the desilverization of argentiferous lead. In all, there are five silver smelting and refining works in and near the city of Chicago. The Chicago Silver Smelting and Refining Company's Works are situated at the little station of South Lynne, about seven miles south from Chicago. The plant at these works consists of one horizontal steam-engine, principally used for running the ore pulverizer, four reverberatory smelting-furnaces, connected by horizontal flues with a common chimney 85 feet high, three lead-softening furnaces, one so-called zinc or mixing furnace, one separating furnace or liquation hearth, one lead-refining furnace, three zinc distillation retorts, one English cupellation furnace, supplied with blast by a No. 3 Sturtevant blower, which is run by a small steam-engine having a vertical tubular boiler, and an assay office, in which there are two wind-furnaces of the ordinary construction, and also a small muffle furnace. The assay office is supplied with all the necessary apparatus and reagents for fire assaying. There are also a superintendent's office, various store-rooms for coke and charcoal, and for the preparation of fire-clay, etc. Recently a small slag hearth (Krummofen) with one tuyere, has been put up for the purpose of working over such slags as assay too high in silver and lead to be thrown away, of which there are large amounts. The principal ore worked while I was in the employ of the company was that of the well known Emma mine in Utah, and also small quantities of Colorado ore. The character of the Emma ore is well known to most members of the Institute. In consists principally of ferruginous mixtures of carbonate and oxide of lead, oxide

Jan 1, 1874

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By Fred C. Bond

There is acute need for a method that will measure the size distribution of finely divided materials, particularly when the particle sizes are smaller than the openings of the finest screen cloth regularly available for testing. Several methods and types of apparatus are in common use, but none are entirely satisfactory for all purposes. The commonest methods are microscopic grain counts, elutriation by liquids or air, and sedimentation. Valuable results have been secured by air elutriating devices, typified by the Haultain Infra-Sizer and the Pearson Air Analyzer. These are especially useful in obtaining sized fractions that can be examined and analyzed separately. They are particularly advantageous because the sizes of the samples produced are adequate for a considerable amount of subsequent manipulation and testing. The sedimentation methods, such as the Wagner and Klein turbidimeters, and the sedimentation balance, do not deliver sized fractions, but they do provide a means for reasonably rapid comparative determina-tions of fineness and surface area, which are important in many industries. The sedimentation balance consists essentially of a balance pan suspended in a liquid that contains falling particles. These are weighed as they settle onto the pan, and the time rate of settling is determined. The size distribution is computed from the settling rate. The balance appears to be inherently more accurate than any of the other methods, and it has served a useful purpose in the study of numerous problems, but there have been limitations which have restricted its scope of application. Because of the essential simplicity of the method, it was felt that intensive investigation might lead to modifications that would make it a valuable tool [or the operators in industries that require precise information regarding the results secured from grinding equipment. A large number of size-distribution determinations below 200 mesh were required in connection with a particular research problem in fine grinding. The sedimentation balance was used in this investigation, and a technique was gradually developed that ultimately gave good results. A serious difficulty appeared early in the work. It was discovered that less material always settled on the sedimentation pan and more on the bottom of the containing jar than could be accounted for by calculation, and also that the material that settled to the bottom of the jar outside the edges of the pan was considerably finer than that on the pan. This segregation was so great that the distribution obtained for the finer sizes was obviously very much in error; material ground to about the degree of comminution of cement might have only 60 per cent of the calculated weight actually settling on the pan, and the error increased with the fine-

Jan 1, 1943

By J. W. Rutter, K. T. Aust

In previous studies of grain boundary migration in zone-refined lead, the authors used bicrystal specimens consisting of a striated crystal which was grown from the melt, and an adjacent striation-free crystal, introduced by artificial nucleation and growth.1 While this method permits the study of the motion of individual grain boundaries, it does not provide control of the relative orientations of the grains. The present note will describe a technique for controlling the orientations of the two crystals in this type of specimen. The technique consists essentially of placing a striated crystal and a striation-free crystal of controlled orientations end-to-end in a graphite trough, then melting a short zone at the junction of the two crystals and allowing it to freeze to form the desired grain boundary. The apparatus used to carry out this process is illustrated in Fig. 1. It consists of a trough milled from high-purity graphite,with grooves in the underside for the placement of thermocouples. The graphite piece fans out on one end at the level of the bottom of the trough; the sides of the trough are completed in this region by the attachment of a mating plate with a slot cut at any desired angle to permit reorientation of the crystal placed at this end of the assembly. The joint between the crystals is made at or near the point where the slotted plate joins the rest of the trough. The thermocouple slots are deepened in this region so that the thermocouples are separated from the melt by only 1/32 in. of graphite. An induction heater, with suitable temperature control, is used to obtain the molten zone. The two single crystals used are first chemically polished in a solution consisting of eight parts glacial acetic acid and two parts 30 pct hydrogen peroxide. They are then placed in the trough with the ends to be joined at the position of the thermocouples. Next, cooling is applied to the two crystals by means of air

Jan 1, 1962

By William Hamilton Merritt

A brief paper on this subject (which might readily be made to, fill a volume) is suggested at this time by several considerations, among which may he named the meeting of the Institute on the borders of Ontario, not far from some of the mining undertakings which are hereafter mentioned ; the mineral developments made in the Province quite recently ; the highly creditable collection of most of the minerals of Ontario, for the first time got together, and exhibited this year at Cincinnati, in the Centennial Exhibition of the Ohio Valley ; and, finally, the recent appointment, by the Government of Ontario, of a Commiesion to inquire into, and report upon the mineral resources of the Province, and the best means to be adopted for their development. The Province of Ontario has no Department of Mines or official geologist, to take note, and keep record, of mining and mineralogical development and discovery. Within the last few years some valuable statistics have been collected by Mr. A. Blue, the Deputy Minister of Agriculture; but recently a desire has risen on the part of the people to obtain further knowledge of these subjects, and the government has appointed a Commission, the report of which is expected to be issued in part, if not in completed form, this winter.

Jan 1, 1889

By L. C. Armstrong

Twice in the past two years and in two widely separated localities—ane near Williamsville, Mo., and the other in the Allard Lake district of Quebec— the Contract Drilling Division of the Longyear Company has experienced perplexing difficulties in drilling granitoid igneous rocks. The rocks in both places are characterized by appreciable amounts of feldspar intimately inter-grown with quartz particles of microscopic dimensions. The disappointingly slow rate of advance and the exceptionally high bortz loss, obtaining during the life of these two projects, are ascribed largely to the resistance to abrasion of these two minerals when arranged in this intergrown pattern. Whether all intergrowth-bearing igneous rocks would offer extraordinary resistance to bit progress cannot be stated with assurance on the strength of these experiences alone. More data on diamond drilling this sort of material in a number of localities are needed before any generalizations can be made safely. It should be pointed out that the lack of time and funds made it impossible for the writer, or other persons interested in correlating the details of bit histories with the kinds of rocks drilled, to be present during the performance of the contracts. However, the records kept in the normal course of drilling are deemed complete enough to be reportworthy. This information is presented here together with the findings made in studies of the rocks involved, with the thought that it may attract the comments of others who may have encountered similar refractory drilling conditions. A pooling of knowledge on the problem would be of material aid in devising more efficient cutting tools and procedures for penetrating this kind of rock. Drilling Blastholes in the Williamsville Granite Due to the unsatisfactory perform- ance of pneumatic percussion drills in boring blastholes on a construction contract near Williamsville, Mo., tests were made with a diamond drill. The poor progress achieved and the excessive loss of diamonds, however, soon led to the abandonment of these trials. The diamonds, in all of the bits tried, lost their cutting edges and acquired a polish after being in service for distances ranging from a few inches to a few feet. Coring bits containing surface-set, whole-stone bortz in a tungsten powder matrix were employed. The cost assignable to bortz wear averaged $7.17 per foot. This item of expense is several times the amount normally expended in diamond drilling in firm, unfractured, granitic rocks. Diamond-impregnated, tungsten carbide bits also were used without success. The diamond wear was at the rate of $0.98 per foot, but the diamond chips became too polished for further duty in less than a foot of drilling. The Williamsville granite is pink and medium-grained. In the hand specimen, it has a fresh, sound appearance; it is seemingly composed almost entirely of interlocking grains of feldspar and quartz and has no discernible features suggesting a greater durability than is usually found in rocks with this composition and texture. Microscopic examination, however, reveals a predominance of feldspar grains with more or less regularly distributed and sharply angular masses of quartz (see Fig 1). The pattern assumed by the two minerals in this mode of occurrence is referred to as a "graphic intergrowth," as it bears some resemblance to the cuneiform characters of ancient Persian writing. The other principal constituents are quartz-free feldspars (microcline and orthoclase) and quartz. All of these constituents are in nearly equidimensional grains, ranging up to about 3 mm in length. There are also

Jan 1, 1950