Search Documents

By Charles W. Wright

At most mines where large tonnages are handled, "bulldozing" or secondary blasting is an important and costly operation. To reduce the large blocks from primary blasting operations or stoping so that they will be small enough to pass through the chutes into the cars at the haulage level, and not too large for the crushing plant, requires blasting. Often this is done by placing a few sticks of dynamite on top of a block with or without a capping of mud, but to consume less dynamite and to promote safety, most secondary blasting is now done by blockholing, or the drilling of holes 6 to 12 in. long in the blocks, using only a part of a stick of dynamite per hole. Regardless of the method of blasting, however, the term "bulldozing chamber" is applied to the room where this work is done. Bulldozing chambers permit secondary blasting at all times in a safe place without disturbance to the other mining operations. The chambers are usually high above the haulage level and well below the stope level or open-pit floor. In most instances the material is passed through a grizzly in the bulldozing chamber, but sometimes no grizzlies are used. One to four raises extend from the chamber to the stope floor and one or two from the haulage level to the chamber floor. Occasionally large slabs of ore or rock choke the raises above the bulldozing chamber, and these have to be blasted by attaching a bundle of dynamite sticks on the end of a long pole and placing them up in the raise between the pieces causing the choke. This is called "chute-blasting." To give a picture of the progressive developments in the use of the bulldozing chamber, a few typical mines that show the application of this method to both metal and limestone mines have been selected for description here. Limestone mines have been included because many metal miners do not realize to what extent the nonmetallic, or rock, miners' are now applying metal-mining methods successfully in their operations. The bulldozing chamber is the "neck of the bottle" for some mines.

Jan 1, 1937

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

Dump Truck Kenworth Motor Truck Corp. is beginning full scale production of its new heavy-duty, end-dump earth mover, model 801, a truck engineered for earth moving under the most adverse operating conditions. Payload capacity of the Kenworth earthmover is 30,000 lb and it is over-tired for safety, flotation and high tire life. The truck's body capacity, struck measure, is 9.9 cu yd, with heaped [ ] load at 11.9 cu yd. The earth-mover has a full anti-friction bearing mounted, power assisted steering gear, simplified controls, minimum turning radius and wide axle track to insure ease of handling, maximum maneuverability and high stability. The offset cab of the Kenworth visibility for the driver, before and after. Circle No. 1 Safety Equipment A compact, safe, and efficient valve assembly approved by the United States Bureau of Mines for use with MSA air line respirators, abrasive masks, and abrasive helmets has been developed by Mine Safety Appliances Co. The new MSA continuous air flow control valve regulates air flow from a compressed air source to an operator using respiratory protective air line equipment. Three parts-a centridge container, a cartridge and the air flow check valve-comprise the entire assembly of the control valve. A position action adjustment knob on the cartridge container regulates the amount of air flowing to the operator. The valve can be detached from the air line instantly by pressing the trigger on the cartridge container near the check valve. As the trigger detaches the hose, the spring loaded ball-type valve, which is attached to the end of the hose, automatically stops the flow of air. Circle No. 2

Jan 1, 1952

By H. Reginald Hardy, Y. P. Chugh, Robert Stefanko

Many materials including rocks, ice, metals and their alloys, wood, etc., emit transient vibrations in the audible and subaudible range when stressed. In rocks, this phenomenon is referred to as "microseismic activity, " "rock noise, " or " seismo-acoustical activity. " In metals this phenomenon is often termed "acoustic emission." Each individual microseismic disturbance is generally referred to as a "microseismim" or an "elastic shock." The terms "microseismic activity" and "microseismim" will be employed exclusively in this chapter. Microseismic activity has been observed in many rocks loaded experimentally in the laboratory.1 The form of a group of typical microseismims is shown in Fig. 1. Quantitatively, the microseismic activity in rock under stress is most commonly described by the number of microseismims observed per unit time. This is commonly known as the "noise rate." The noise rate in general increases with increasing stress level and rises sharply just prior to failure of the material.2 The origin of microseismims is not well understood, but it appears to be related to processes of deformation and failure which are accompanied by a sudden release of strain energy. In a polycrystalline material, microseismims may originate at the micro-level as a result of dislocations or at the macro-level by twinning, grain boundary movement, or initiation and propagation of fractures through and between the grains. It is assumed that the sudden release of stored elastic strain energy accompanying these processes generates a stress wave which travels from the point of origin, within the material, to a boundary where it is observed as a

Jan 1, 1972

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories ; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgCO3) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1964

By W. H. Craigue

THE scope of this article covers only the mathematical principles involved in discounting to present worth future expected profits and it is believed answers definitely two questions, which were raised at a recent meeting of the Committee on Methods of Valuing Coal Properties, as follows: 1. The accumulative effect of carrying charges on the value of coal mines showing definitely the number of years beyond which the coal may not be mined at a profit and subsequent to which the possession of any unmined coal will be a liability rather than an asset. 2. The effect on the valuation of coal mines, in the presence of the carrying charges described in question 1, of an increase in plant capacity and production. In general, in considering these questions, it may be stated that the consideration of an increase in plant capacity and production follows as a matter of course after a determination has been made of the year beyond which no profits are to be realized (giving the carrying. charges accumulative effect, or in other words capitalizing the carrying charges, as shown hereinafter). For example, if it is determined that any coal that is unmined after 45 years will have no value or less than no value, the question immediately arises as to whether or not a plant should be constructed that would result in a yearly production great enough to extract the entire tonnage in a time less than 45 years, and if so the number 'of years less than 45 years that would, from a financial stand-point, be the most desirable, all under the assumption that the market for the product or the transportation facilities are such that the yearly production can be increased to the desired amount.

Jan 1, 1933

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946

By Kenric C. Owen

INTRODUCTION Situated 23 miles east of Pretoria the Premier Mine started diamond production in 1903. Two years later it produced the largest diamond yet discovered, the 3 106 carat Cullinan stone. For the period to 1932 when the mine was closed down due to economic circumstances, open cast mining was practised using inclined rope haulage traction and by this time had produced 48.5 million carats of predominantly industrial quality diamonds from 148 million tons of ore. In 1945 it was decided to re-open the mine using underground mining methods. A system using long hole benching was devised (Hodgson and Sewel 1960). This system was later modified but still forms the basis for approximately fifty percent of production. Following the successful introduction of block caving on associated diamond mines in the Kimberley area (Gallagher and Loftus 1960) this mining method was introduced to the Premier Mine in the late 60's and now accounts for nearly 50% of production. This paper will discuss block caving at Premier Mine in the light of our experience and discussion will be directed to the main geological and structural features of the orebody and host rocks and the related constraints imposed on the mining methods. Reference is made to the long hole benching mining method for comparative purposes. GENERAL DESCRIPTION OF OPERATIONS The ore from the block caving and bench mining areas gravitates via ore passes to a twin haulage, 500m below surface. Electric 13 tonne locomotives, each hauling a train of 10 Granby type cars, deliver the ore to two 42" x 48" (1.06m x 1.22m) jaw crushers. The ore is reduced in size to minus 0.15m before being hoisted to the treatment plant on surface. Hoisting is done with 12.5 tonne bottom discharge skips in a five compartment rectangular shaft using two 3 240 H.P. semi automatic Ward Leonard winders. A small single drum service winder operates in the other compartment. Men and materials travel in a separate shaft in a 5,4m x 2,8m cage operated by a Koepi winder. These two shafts are also the main intake airways to the mine. The two main extraction fans capable of 250 m3/s at 3,2 kPa are situated on surface and are connected to the underground workings by an incline and a network of air passes and return airways. GEOLOGY Although there are numerous occurrences of kimberlite bodies in the district, the Premier Mine kimberlite pipe is the only economic orebody. It is roughly oval in shape with surface dimensions of 900m on the long axis and 450monthe short axis. The surface area is 320 000 m2. The kimberlite has intruded a massive body of felsite and norite which is intersected by a number of faults. The contact between the kimberlite and host rock is clear cut and dips inward at an average angle of 80°. Cutting across the pipe and the country rock is a 75 metre thick gabbro sill, the top of which intersects the pipe below the 347m level and dips at 15' to the north west. The kimberlite has been metamorphosed a distance of some 20m both above and below the sill contacts. Age measurements on biotite from the gabbro date the sill as 1 115 million years, thereby providing a minimum age of the pipe. (Pre Cambrian). All other pipes in South Africa are of Cretaceous age (60 million years). A simplified geological plan and section of the Premier Mine orebody is shown in Figure 1. It is thought that the kimberlite intruded in at least three distinct phases. The kimberlites of these different phases can be distinguished most easily by their characteristic colour. BROWN KIMBERLITE. This is the oldest kimberlite and forms a crescent shape in plan on the south eastern side of the pipe. In depth it increases in relative area. Although the brown kimberlite carries the highest diamond grade in terms of carats per ton all the various kimberlites in the Premier pipe are economic to mine.

Jan 1, 1981

those who are to lie in the torn fields of France. Today we read of Lieut. William Hague, whom we said good-by to hardly more than a month ago-—so clean, ao young, so strong—who, abandoning the professional career in which he had won such commendation and which held for him such promise, leaving his wife and his little boy to whom he was so dear, answered at once the call for men of his training, and is now dead "in the service of his country." There are many friends of that courtly and dignified gentleman James D. Hague who recall, both here and in Stockbridge, the parental pride in the promising lad of such a little time ago—the eager schoolboy at Milton, the rather grave youth at Harvard, his entry into new experiences in the Western mining world, and who, seeing him during his stay at Camp Upton, realized that the old Puritan stock was still sound and true—and now with him the struggle is over and the sacrifice made. Captain William Teasdale Hall Captain Hall, who was admitted to Junior Membership in the Institute in 1915, while still a student of mining at the University of Toronto, was killed in action in France on May 19, 1917. Captain Hall was born in Toronto in 1893, and received his academic training at Harbord College, from 1908 to 1911, when he entered the University of Toronto, School of Practical Science. During the three summer vacations of his university course, he was employed by the O'Brien mine at Gowganda, next by the McIntyre Mining Co., at Porcupine, and finally by the Mines Branch of the Geological Survey, which was conducting magnetic surveys to the north of Port Arthur. When war was first declared, Mr. Hall endeavored to join the artillery as an officer, and for the purpose secured a provisional lieutenancy with a Hamilton battery, but he did not receive an overseas appointment, and on being graduated as a mining engineer in 1915, he was offered a position in Chile, which he accepted. He left Toronto on May 27, 1915, and was engaged in Chile as a mining engineer for nearly a year. In the latter part of April, 1916, he decided to offer himself again for service at the front. He crossed the Andes and sailed for LiverpooI, where he landed on May 13, 1916. On May 27, 1916, Captain Hall was given a commission as a lieutenant in the Royal Flying Corps, 21st Squadron. He went to the front on Sept. 1, 1916, and remained there continuously. His

Jan 1, 1920

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has had a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1790. Practically all of this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the "white man" Indians are known to have made salt from such salt springs as those that existed at Avery Island, La., Charleston, W.Va., Saltville, Va., and Onondaga, N.Y. In 1862 the first rock salt was mined in the U.S. from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, Va., and then at Retsof, N.Y., in 1885. Of the more than 40 million tons produced annually in the United States, about 68% or 27 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc.

Jan 1, 1975

By V. V. Valleroy, A. J. Cornelius, B. T. Willman, G. W. Runberg, L. W. Powers

This paper reports the results of an investigation into the use of steam as a recovery agent. High oil recoveries by steam, as much as 100 per cent greater than by water flood, were demonstrated in laboratory linear cores. The principal mechanisms responsible for the additional oil have been identified as (1) thermal expansion of the oil, (2) viscosity reduction and (3) steam distillation. Although the first two also enhance recovery by hot water flood, they are effective with steam injection at lower volumes of produced fluids. Steam-zone residual oil saturation is independent of initial saturation. Recovery by steam is greater for lighter oils because they contain a greater fraction of steam-distillable components. Equations for the steam-zone advance in a radial homogeneous system are presented; these show the effect of reservoir parameters. The displacement in the hot liquid region moving ahead of the steam front can be estimated by a calculative procedure which is suggested. The method which takes account of the temperature gradient is applicable also to a regullar hot water flood. INTRODUCTION Considerable industry interest in the application of heat to petroleum reservoirs as a means of increasing oil recovery has been evident in the past few years. Three thermal methods which have attracted interest are (1) the injection of saturated steam, (2) the injection of hot water and (3) the injection of air into a formation to support combustion within the reservoir. Much has been published in recent years on underground burning, and there have been several papers on hot water injection. Although there are several early reports1,2 on steam injection, no recent experimental studies have been published on this recovery method. In our early thermal methods research, a marked improvement was found in oil recovery by steam injection compared with recovery by water injection in the same system. An investigation subsequently was undertaken to obtain quantitative information from which to evaluate steam injection as an oil recovery method. In addition, it was desired to investigate the recovery mechanism of hot water as compared with that of "cold" water and steam injection. An understanding of the mechanisms by which these processes operate would generally define favorable field conditions for their successful application. This paper reports the results of the laboratory study and suggests calculative approaches to estimate the field behavior of the steam-injection process. EXPERIMENTAL METHOD EQUIPMENT A schematic diagram of the equipment used for the displacement tests is shown in Fig. 1. Essentially, it consisted of a core with suitable means for recording temperatures, a feed system for injecting steam or cold or hot water, and a receiving train for condensing, cooling and measuring produced fluids. For the steam experiments, air-free saturated steam was piped from the boiler to the core face in insulated lines that were provided with steam traps and bleeds to remove any condensate formed in the lines due to heat losses. A 12-in. section of the line immediately ahead of

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By R. F. Mehl, M. Gensamer

Creep investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that application of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and structural character of the solid metal. Basis of Investigation Much of the investigation that has been given to the creep characteristics of metals and alloys has been directed toward studying the dependence of creep rate upon stress. Great interest has centered upon the approximately uniform rate of flow that has been demonstrated for numerous metals and alloys. At temperatures above the strain-hardening ranges of materials, this uniform rate frequently is attained after a relatively short period of initial rapid flow, and the period during which it persists determines for most practical purposes the useful life of the

Jan 1, 1938

By J. M. Kane

IN all probability the mining and metallurgical industry as a whole can demonstrate a larger economic return from installation of dust-control equipment than any other major industrial group. This fact has partially accounted for the marked increase of dust-control installations made during the past decade. While the primary objectives for installation of dust-collecting systems are improved working and operating conditions for men and equipment, the fact that an economic return can be anticipated on salvageable materials is an added advantage which shows in partial or complete equipment write-off. The conditions apply to most phases of the mining, milling, and smelting industry, both non-metallic and metallic.

Jan 1, 1953

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the froth-ability of pine oil is governed by: 1—rate of aeration, 2—time of aeration, 3—height of liquid column, 4—chemical composition of pine oil, 5—pH value of solution, 6—temperature of solution, and 7—concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.' The results also show that the relative froth-abilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of re-producibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1—compressed air and its regulating system, 1-3, are eliminated; and 2—a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifying and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.' Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec, which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1953

By P. C. Kapur

A principal first-order and a minor summation term contribute to the solution to the discretized batch-grinding equation when formulated in cumulative retained mode. Depending on the inter relations hips between the selection and breakage parameters, the minor term may be advantageously modified in a number of ways. The reduced grinding equations thus obtained are solved by iterations to give relatively simple solutions which are tested against experimental data. The irn-plications and advantages of the reduced grinding equations are briefly discussed. In many instances, the trajectory of the particle-size distribution in a batch mill may be extracted from a set of particle mass balance equations as follows

Jan 1, 1971

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965