Search Documents

By E. R. Hoskins

Results of a primary stress measurement investigation conducted on the 1100 copper ore body of the Mt. Isa mine, Mt. Isa, Queens., Australia, are presented in this chapter. The investigation started in September 1965, after discussion with the engineering staff at Mt. Isa, and consisted of both underground or in-situ tests at Mt. Isa and laboratory tests on Mt. Isa rocks and stress measurement techniques at the Australian National University in Canberra. Underground stress measurements were made in and adjacent to the 1100 copper ore body. The primary stress measurement site was in J 32 west crosscut on 14 Level. Approximate coordinates on the mine grid are 3000 north, 1650 east. The vertical depth below ground surface at this point is approximately 2180 ft. Some preliminary measurements were made in M 30 west crosscut on 13 Level, coordinates 3000 north, 2000 east, depth beneath the surface approximately 1990 ft. Additional flatjacks were installed on 11 Level in L 30 west crosscut, coordinates 3000 north, 2200 east, and depth beneath the surface approximately 1580 ft. All of the sites were in rock that from a mining engineering viewpoint must be considered extremely sound. The 13 and 14 Level crosscuts were approximately 14 ft on a side and nearly square and the 11 Level crosscut was approximately 10 ft on a side. All of the crosscuts had been standing open for several years and no artificial support of any type was necessary. Extraction openings hundreds of feet on a side have been made in this mine in similar rock and these have remained open also without additional support (see Davies 1 for a recent summary of mining techniques and conditions). The geology of the Mt. Isa mine has been most recently described by Bennett.2 Briefly, Mt. Isa is a silver-lead-zinc and copper mine in a series of Precambrian siltstones, shales, and bedded carbonates that strike north-

Jan 1, 1972

By W. G. Pfann

WHEN a molten zone traverses a long, solid ingot in a level, open boat the ingot becomes tapered. While the taper may be slight after one zone pass, it can be appreciable after repeated zone passes, even to the extent of causing an overflow of matter at the end of the boat. It will be shown here that such matter transport by a molten zone arises from the volume change on melting and that it corresponds in magnitude and direction to the magnitude and sign of the volume change. It will be shown also that the mechanism of matter transport is basically similar to that of solute transport by a molten zone, which has been discussed elsewhere,1,2 and that the two processes can be described by similar equations. Finally it will be shown that matter transport can be prevented by inclining the ingot at a critical angle. Contraction on melting results in forward transport, that is, transport in the direction of zone travel; expansion on melting results in reverse transport. The way in which forward transport arises from the contraction on melting may be seen as follows: At the starting end of a solid horizontal ingot of uniform rectangular cross section of height h., form a molten zone of length 1, as shown in Fig. 1. The height h of the liquid will be h. where a is the ratio of density of solid to that of liquid. Advance the molten zone, at constant length, a distance dx. The volume of solid melted will be hdx; the volume of solid frozen will be Izdx, because the height of the freezing solid will tend to be equal to that of the liquid. The resultant change, dv, in liquid volume will be the difference in these quantities multiplied by the density ratio. Hence the following equation may be used for a zone at any distance x from the origin: which is valid in all but the last zone length in the

Jan 1, 1954

By C. W. Allen, B. D. Cullity

The proportional limit of iron crystals in torsion is governed by the resolved shear stress in the most highly stressed slip systems, averaged around the specimen circumference, and does not obey a critical resolved shear stress law. Crystals of most orientations exhibit a stage of easy plastic deformation, akin to easy glide in tensile or shear specimens. Transient deformation, similar to that which occurs in single crystals of other materials, is also observed. THE torsional deformation of single crystals of magnesium (hcp) and aluminum (fcc) has been described recently by Choi et al.,&apos; especially with respect to the criterion for the orientation dependence of the onset of plastic flow in these materials. The purpose of this paper is to present results of torsion tests of iron single crystals and thus to extend this yield criterion to a bcc metal. In addition to considering the variation of proportional limit with crystal orientation, this paper also briefly treats work hardening, transient deformation, and the mechanism of plastic flow in iron. The effects of the method of surface polishing and the chemical purity of the iron have been investigated. STRESS DISTRIBUTION It is convenient to express the stress at any point of a cylindrical crystal stressed in torsion in terms of t0, which is the shear stress acting at the surface on a plane normal to the axis of the cylinder and in a direction tangential to the cylinder. This stress is given by To = 2T/pr3 [1] where T is the applied torque and r the specimen radius. The shear stress t, resolved in any chosen slip system is given in terms of 7, by1 Ts/TO = sin 0, cos d sin (0, -) + cos , sin d sin d - ) [2] where 0 and d are the angles between the specimen axis and the slip plane normal and slip direction, respectively; h is the angular circumferential position on the specimen at which t, is being determined, measured from an arbitrary reference plane which includes the axis;o and d are the angular coordinates of the projections of the slip plane normal and slip direction on a transverse section with respect to this same reference plane. Slip in iron occurs in a <1ll> direction on the {ll0}, (1121, and (123) planes, which together comprise 48 slip systems. A complete evaluation of the stress distribution in an iron crystal stressed in torsion would therefore require a calculation of Ts/T0 as a function of for 48 different slip systems. Fortunately Gough,&apos;who studied the behavior of iron crystals in alternating torsion, was able to simplify this problem considerably. He showed that it was sufficient to consider a kind of average slip plane for each slip direction, namely the mathematical plane of maximum resolved shear stress containing the slip direction considered. This simplifying approximation is possible because, for each slip direction, the active slip plane or planes lie very near this mathematical plane of maximum shear stress. Vogel and rick&apos; have critically reviewed the early work of Taylor and Elam,13 Taylor,14 and Fahrenhorst and schmid8 from which the identification of the above crystallographic planes as slip planes in the bcc lattice largely stems. While their criticism is clearly justified, their own results do little to clarify the issue. The role of cross slip (screw dislocations changing glide planes) is evidently so important in this case, as Read3 has suggested, that methods for deducing slip systems from observations of gross slip traces are inadequate, such traces commonly arising from complex dislocation motion. Thus the treatment given here involving the plane of maximum resolved shear stress seems a logical simplification especially in view of Gough&apos;s2 study of a iron. There is, however, an assumption built into the subsequent treatment the comparative validity of which is difficult to assess, namely, that slip in all slip systems in iron may be characterized by a common critical resolved shear stress. The shear stress 7, resolved in a slip direction defined by d andd, and on the plane of maximum shear stress containing this direction, is found by first maximizing 7s/70 with respect to either Oo or 4,. The slip plane coordinates are then eliminated by using the relation between 0, ,o and d, d, namely,

Jan 1, 1963

By B. Trafton, H. L. Hartman

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. The revised program-written in FORTRAN for the IBM 7074 computer in Penn State&apos;s Computation Center-is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following: 1) Distributes an assumed total quantity of air flow among all airways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2) Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3) Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values. The basis of analysis used is the Hardy Cross method of successive approximation for solution of any fluid network, explained in detail in the earlier article. In brief, corrections to assumed air flows are computed for all the loops of a network; following distribution to the airways of each loop, the process is repeated until acceptable accuracy is attained. When a hand or desk-calculator solution is used, there is advantage to close approximation of the actual flows in the original assumption of air-flow distribution in the network. Since publication of the previous paper, in which assumption of initial quantities was also necessary in the computer solution, the program has been modified to make the first distribution itself, assigning the total quantity to one specified path in a split and then proceeding to correct the flows. The number of iterations required for a high-accuracy solution is little affected, at least in networks of few loops, 10 to 15 being sufficient to reduce the error to 1 pct or less. The principal limitation of the original program was that it contained no provision for handling a fan. Further, it did not determine the overall head loss in the network and was not designed for multiple parallel openings, such as occur in coal mines. The revised program was written to overcome these disadvantages and also to print out the adjusted flows for all airways, corrected for the system operating point. At the present time, the program can handle only an external fan. The procedure employed in solving a ventilation network is now as follows: 1) Input data consisting of airway characteristics and loop designation along with assumed direction of flow, for each branch of the network and any trunk airways, are fed into the computer. 2) Employing the resistance relationship, where R is resistance, K is friction factor, P is perimeter, L is length, A is area, and n is number of airways (where multiple intakes and returns are employed); values are computed for all airways. 3) An arbitrary, continuous route of flow through the circuit—from beginning to end—is selected and the path identified by airway numbers and read in. 4) Based on a total assumed quantity of flow Q (usually 100,000 cfm.) the computer employs the procedure described in the previous article in distributing quantities of flow among all the airways until a satisfactory level of accuracy has been attained (in the current program, the machine is turned off when the cumulative corrective error in cfm, is reduced to five times the number of airways). 5) Airway head losses H are calculated by the relation H = R Q2 and cumulated along the original designated flow route to find the overall head loss for the network. Trunk airways are then included to obtain the mine head.

Jan 1, 1964

By Leonard L. Melton, Calvin D. Saunders

The design and performance of many operations common to the petroleum industry depend upon the unique properties of a class of materials known as non-Newtonian fluids. The art of measuring and describing these properties, called rheology, has fallen far behind the field applica-tion of these fluids in this industry. Empirical methods are still employed although theoretically sound methods of analysis are now available. This paper illustrates a completely general method of analysis of the rheological properties of non-Newtonian fluids which id independent of the type of viscometer employed and also the rheological type of fluid encountered except those of a thixo-tropic or rheopectic nature. Values of the rheological properties of a fluid obtained using this method of analysis are based upon an absolute scale of measurement, eliminating the necessity of employ-jng arbitrary concepts of the flow properties of non-Newtonian fluids, The fundamental nature of this method of analysis is further demonstrated by evaluating the precision with which measurements have been made of these rheological properties by employing a dimensionless criteric: —the Fanning friction factor-Reynolds number correlation. INTRODUCTION Non-Newtonian fluids are not new in the petroleum industry. Particular properties of non-Newtonian materials have been recognized and used to advantage in drilling fluids and have found excellent application in the hydraulic fracturing process.&apos;.&apos; While usage of these fluids is not new in this industry, the art of measuring and describing their rheological properties is still in its infancy. This is reflected in the accepted method of evaluating drilling fluids, API RP 29, (1950), which recommends a one point "viscosity" measurement. These shortcomings are recognized by various groups in the industry and more adequate methods have been prposed.3,4 The efforts Of these people are to be commended; but, at the same time, the limitations of their method of analysis and viscometer must be appreciated. This method Of analysis is applicable Only to Bingham plastic fluids as is pointed out early in their articles. The consistency of a Bingham plastic fluid must also lie within the range of the viscometer which is also well defined by the author. It is believed that the apparent simplicity of this method of analysis and the utility Of Operation Of their viscometer will soon make the terms non-Newtonian fluid and Bingham plastic fluid synonymous as used in this industry; a tendency which has already been encountered. Application of this method of analysis to a non-Newtonian fluid other than a Bingham plastic can lead to erroneous results. The field of rheology has long been hampered by the adherence to arbitrary concepts of Of of the flow properties Of non-Newtonian fluids. This has resulted in the design and operation of viscometers so as to fulfill these concepts rather than following the more logical method of analyzing experimental data so as to yield a fundamental truth. completely Bingham proposed the concept Of plastic flow and yield asu rement. data presented by Buckingham could hardly be interpreted so as to substantiate this theory; but rather succeeded in establishing the fact that compliance with this flow concept could never be realized in the capillary tube vis-cometer.5 Bingham, in reply, sug-gested "Rather than complicate our formula, it would seem to me a much better plan to so change the conditions of flow that the formula will be linear... Reiner0 stated .This plan has been followed by me in collaboration with Miss Riwlin. . . . From the present paper (Reiner and Riwlin, 1929) it will be seen that it is possible to choose the conditions of flow so that the formula based on Bingham&apos;s law of plastic flow remains linear. This is realized in the rotation viscometer," Thus, a viscometer, with design and operation based on the Reiner and Riwlin equation for plastic flow, is restricted to a specific range of flow

Jan 1, 1958

By L. M. Barker, E. G. Lewis

THE literature of milling is replete with papers devoted to the subject of ball milling, all of which no doubt have contributed in one way or another to progress in that art. In this paper reference will be made to only a few of the many authors, but the value of the contributions of all who have written on that subject is hereby acknowledged. With a few exceptions the efforts of most students of the subject have been devoted to laboratory investigations of principles. Davis1 was one of the first to report on plant-scale investigations and to present to mill men certain criteria for the guidance of ball-milling practices. His conclusions with respect to the significance of sizing analyses of classifier sands in their relation to the factors of mill speed and ball sizing are particularly referred to. Those conclusions were: I. If the balls are large or the speed of the mill is high, crowding will appear at the finer sizes in the classifier sands. 2. If the balls are small or the speed is low, crowding will appear at the coarser sizes in the classifier sands. 3. The indications are that best efficiency is obtained when the screen analysis of the sands show a minimum crowding at any size. The last conclusion was qualified by the statement that it had not been proved conclusively. It is surprising, however, that the literature of later years reveals little evidence that millmen have made any serious attempt to apply those criteria. This may, perhaps, be explained by the fact that the average plant-scale ball-milling problem presents so many variables that an investigation of any one of them encounters the problem of control of the others-a problem that often is unsurmountable in a small plant. In a large plant, in which there is a duplication of grinding units in parallel operation, opportunity may be afforded for determining the value of such criteria. Nevertheless, a study of published data from grinding circuits of both large and small plants suggests that either Davis&apos; criteria have been tried and found inapplicable or have never been given consideration. For the purpose of testing Davis&apos; conclusions and with improvement of ballmilling efficiency as the final objective, a test program was initiated in the concentrator of the New Cornelia branch of the Phelps Dodge Corporation early in 1938. The practices of that plant have already been described.2 The fine-grinding units are arranged so that any one of eight units may be operated as a test unit and its results compared with those of the remaining units. All units receive similar feed from a common storage bin, in which the product of the fine-crushing plant is bedded by traveling tripper. The ball mills are all similar in size and operated at the same speeds, and are individually metered. The feeder conveyors of each unit are equipped with Merrick weightometers. The test program as initially outlined proposed investigation of the following:

Jan 1, 1941

By B. Zondek, W. T. Cardwell, J. W. Sheldon

The fundamental equations that are used to describe two-phase fluid flow in porous media are Darcy&apos;s law for each phase and an equation of continuity for each component. The special case of one-dimensional, incompressible, two-phase flow has received much attention in the petroleum engineering literature.1-10 The basic paper on the subject is that of Buckley and Leverett.2 Buckley and Leverett showed that one could eliminate the pressure and obtain a single partial differential equation for the saturation. They solved this equation for the case when gravity and capillary forces are negligible. A frequently encountered property of the solution of the basic partial differential equation is that, as time progresses, the saturation becomes a multiple-valued function of the distance coordinate, x. Buckley and Leverett interpreted the formation of multiple values as an indication that the saturation-distance curve had be-come discontinuous. They developed a method of determining the position of the discontinuity from a material balance. We solve the Buckley-Leverett partial differential equation using the method of characteristics and the concept of shocks. Our treatment is analogous to treatments used in the theory of supersonic compressible flow." Although the numerical results obtained are the same as those obtained by previous methods, we believe that this approach is more logical and has broader applicability. It can, for example, be generalized to treat the case when the fluids are compressible. It is not clear how one would go about doing this using the method of Buckley and Leverett. To illustrate the power of the method of characteristics with shocks, we solve a problem in gravity segregation which has not been treated previously in the literature. A special case of the general method developed here was used by Welge, to solve a particular fluid displacement problem. We consider two-phase incompressible flow along the vertical direction x in a porous medium. We assume that there is no flow transverse to .x. We measure positive in the upward direction. The fundamental equations are obtained from Darcy&apos;s law and the mass conservation law. Since the two phases are incompressible, mass conservation is equivalent to volume conservation.

By T. Egleston

I HAVE to announce with great regret that our distinguished honorary member, Louis Gruner, died in Paris in March last. The Institute, in his death, has lost one of the first as well as one of the greatest of its honorary members. I speak with great feeling, as he was both my instructor and my friend ; and I am sure that if he could hear what I am about to say of him, lie would object to it. Mr. Gruner&apos;s modesty was such as even to prevent, except in his own Corps, the thorough appreciation of his work in his own country. I think be mas better appreciated by those who are familiar with his labor in almost any other country than his own. A just man, a thorough scholar, a great investigator, he was so unselfish that almost the last act of his life, and the last letter he signed, only a few hours before his death, had for its ohject to render a service to one of his former pupils. I think no one who mas ever associated with him could forget, in the greatness of his learning, the sincere and earnest friend, mho was always ready to render a service, where such service could be rendered even at great inconvenience to limself. His own motto, "Sein, nieht schein;" that is, "Be, not appear to be," was singularly descriptive of his character; and, what is more than all, he was one of the most earnest Christian men with whom it has ever been mv. good fortune to be thrown in contact. There are few such men. He was one of the greatest metallurgists that Europe has ever produced; a man the more remarkable because, though known to most of us as a metallnrgist, some of the best work of his life was in the domain of geology to which he contributed very important researches and memoirs, which will remain permanently among the valuable additions to the geology of his own country. He was, at the same time that he was the greatest metallurgist in Europe, a brilliant chemist, a thorough geologist, a distinguished professor, and an expert, practical miner, whose advice and methods had only only to be known to be followed. Mr. Gruner was born in Smitzerland in 1809, and graduated from the Polytechnic School of Paris in 1530 and entered the School of Mines, from which he graduated with distinction in the Corps of Government Engineers of Mines at an early age, and was immedi-

Jan 1, 1884

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10&apos;6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963

By D. D. Pollock

Many constitution diagrams do not indicate the limits oJ solid solubility of the silver-rich solid solutions below 200°C. Thermoelectric measurements were employed to determine this limit in the nieighborhood of room temperature. The appearance of a second phase causes a discontinuity to occur in the tkevtrroelectric power as a function of cornposition at constant temperature and pressure. This discontinuity was employed to determine the limits of the silver-rich terzinal solid solutions of the Ag-A l, Ag-As, Ag- Bi, Ag--Ge, Ag-In, Ag-Pb, Ag-Sb, and Ag-Sn systenls at 30°C. CONSIDERABLE work has been done on the constitution of binary alloys of silver. The available data have been compiled by Hansen1 and Elliott.2 However, many of the binary diagrams do not show the limits of solid solubility of the silver-rich solutions below about 200° C. This work was undertaken in an attempt to extend these limits to the neighborhood of room temperature . PREPARATION OF ALLOYS All of the alloys were made with silver containing less than 0.014 pct (by weight) of impurities. The materials were weighed out into 225-g heats and melted in a high-frequency induction furnace. The indium, tin, and antimony alloys were melted in A1203 crucibles, under a boric anhydride cover, and were poured into split graphite finger molds. The aluminum, germanium, arsenic, lead, and bismuth alloys were melted in machined graphite crucibles; they were also covered with boric anhydride and poured into split graphite finger molds. The $-in.-diam ingots were heated to 750°C and were forged and hot-rolled down to 0.1 by 0.1 in. The wires were pickled in a 25 pct HNO3-75 pct H2O solution to remove any oxygen-rich surfaces. The wires were then annealed at 550°C for 2 hr in a dissociated ammonia atmosphere. They were then furnace-cooled for 20 hr to room temperature in this atmosphere. The wires were cold-drawn to 0.0808 in. diam. The finished wires were again annealed at 550°C in the same manner as in the first anneal. Thermoelectric Power. The thermoelectric power of a single specimen of each alloy was determined against pure silver which contained a maximum impurity content of 0.014 pct by weight. The wire specimens were straightened and then cleaned with ethyl alcohol. They were then reannealed in the same way as the finished wires to assure that any residual stress would be at a minimum level. Previous work has shown that the presence of small amounts of stress has the effect of decreasing the thermoelectric power. The alloy specimen was soldered to the pure silver wire to form the measuring junction. A standard set of copper leads was then soldered to the reference junctions of the thermocouple. These junctions were maintained in separate dewar flasks which contained finely shaved melting ice during the test. The thermal electromotive forces of the thermocouples were measured at four temperatures between 15° and 45°C. A known source of electromotive force was balanced against the output of the thermocouple until a null balance was reached. The data were then expressed in terms of the thermoelectric power at 30°C. The results were then converted to absolute thermoelectric power, s303.3 These data have an average error of less than ±0.2 pct. RESULTS AND DISCUSSION All of the experimental data are given in Table 11. Since the electromotive forces of the binary alloys of silver were determined against the pure silver from which they were made, the resultant thermoelectric powers are only a function of the intentionally added binary elements at the constant test temperatures. This provides a direct measure of the effects of the alloying elements. The absolute thermoelectric power of an alloy of silver is given4 by:

Jan 1, 1968

By R. S. Hooper

In attempting to describe recent mining developments at the Bunker Hill mine, it may be well to recall first the old days of hand mining when holes were laboriously drilled by hand to a maximum depth of three feet, and were shot one or two at a time, in order that the miner could take advantage of every slip, crack or bedding plane, and so save as much drilling as possible. Broken muck, of course, was loaded by hand shoveling into wheelbarrows or small cars, and heading advances or stope tonnages were governed by the number of men that could find room to work in any given place. The first big improvement over these old methods was the introduction of the reciprocating type of air-powered rock drill. This innovation, crude as it was, enabled the miners to set up a machine and drill a complete round of holes in one shift; but broken muck was still loaded by hand, and the size and rate of advance in headings were limited by time required to remove the broken rock. The next improvement of consequence was the appearance of the hammer-type rock drill, which greatly increased drilling speed over the reciprocating type, and made possible the completion of a full cycle in one shift, by the use of crossbars in headings, and permitted drilling and mucking to be carried on at the same time. Rock drills continued to improve as time passed, and finally the smaller and more efficient mucking machines appeared on the scene, and it became possible to muck out a round of broken rock and have a clean setup for one or more drill columns and machines. A complete cycle of mucking, drilling, and blasting was completed in one shift with an average advance of five feet. These conditions prevailed for several years, but as the mine grew deeper, the distances to transport the workers grew longer, and this fact together with the shortening of the working day, soon presented the problem of attempting to complete a cycle of operations in a shift of only six hours at the working faces. Anticipating this condition, the operating heads at the Bunker Hill had started an intensive study of more and better mechanization, and over a period of comparatively few years have adopted and placed in service methods and machines that make it possible for a three-man crew to consistently advance headings seven by nine feet in cross section, at the rate of eight feet, and more, per shift, doing all the mucking, switching, drilling and loading. These improvements consist of the following major items: I. The development of a light, flexible, easily transported jumbo equipped with pneumatic columns (Fig I), that has decreased the "setting up" and "tearing down" time an average of 11/2 hr per shift, Or 25 PCt of the available working time. These jumbos were developed at the Bunker Hill mine by members of the staff and consist of two pneumatic columns attached to a suitable carriage. They fold

Jan 1, 1949

By A. H. Heim

A method and apparatus for measuring gas porosities of rocks are described. The apparatus can be assembled from commercially available components. In principle, measurements are made by volume substitution at constant pressure. The maximum error is not more than 0.3 porosity per cent. Typical results are given. INTRODUCTION Determining the porosity of rock samples is one of the most important and yet most varied types of measurement in core analysis. Among the many techniques devised are the so-called "gas porosity" methods. An old and well known example is the Washburn-Bunting method.&apos; The U. S. Bureau of Mines2-&apos; described and later improved the apparatus for a now widely used method generally known as the "Boyle&apos;s law" method. In the present form of the Washburn-Bunting method,&apos; the volume of air in the pores of a rock sample at atmospheric pressure is extracted and then collected in a graduated burette at atmospheric pressure. The volume of air is read directly as the pore volume of the sample. The absolute error in reading the collected volume of gas is independent of the total volume; thus, the relative error is larger when the volume is small, as it is for rocks of low porosity. In addition, the sample after measurement contains mercury, which limits its use for other analyses. The Bureau of Mines (or Boyle&apos;s law) method measures directly the solids volume of a sample from which the pore volume and porosity are derived, using a separate measurement of the bulk volume. Gas at a few atmospheres pressure is introduced into a sample chamber of known volume containing the rock sample. The pressure is accurately measured. Following, the gas is expanded into a burette at 1 atm, and the gas volume is read directly. From the initial pressure p, and the final pressure p2 and volume v,, the initial gas volume v1 is calculated using Boyle&apos;s law; that is, p1v1 = p2v2. Volume v, minus the volume of the empty sample chamber is the solids volume of the sample. The accuracy of the method is limited, unless corrections are made, by deviations of the gas from the "ideal" gas-law behavior assumed in the simple form of Boyle&apos;s law. The purpose of the present paper is to describe a method for measuring the gas porosity of a rock which avoids many of these difficulties. Gas volumes are measured directly with the same accuracy as the bulk volumes. Pressures of at least an order of magnitude larger than those of previous methods are employed to insure rapid penetration of the gas into the sample. While special equipment may be built to apply the method, the porosimeter may be constructed as well from commercially available components. For simplicity, the apparatus described will be referred to as the "Constant-Pressure gas porosimeter". THE CONSTANT-PRESSURE METHOD Fig. 1 shows schematically the arrangement of components comprising the present Constant-Pressure porosimeter. Briefly, the method is one of volume substitution and may be considered a null measurement. Omitting (for the present) some of the operational details, the method of measurement consists of the following three steps. 1. After evacuation, the volume of the measuring system (a ballast chamber, a manifold, two gauges and their connections) up to the sample chamber is filled with gas to a high pressure (- 1,000 psi). A sample of the gas at this pressure is trapped in one side of a sensitive differential pressure gauge to serve as the reference pressure for subsequent steps. 2. The evacuated sample chamber containing the rock sample is opened to the measuring system. As the gas expands into the chamber, the resulting decrease in pressure unbalances the differential pressure gauge. 3. The pressure is restored by means of a mercury volumetric pump. The volume of mercury injected exactly equals the free or void volume of the sample chamber (volume of empty chamber minus the solids volume of the rock within). From the injected volume and the known empty chamber volume, the solids volume is obtained and the porosity calculated. The pressure and the volume occupied by the gas are the same before and after opening the sample chamber. Expansion and compression of the gas are incidental operations and do not enter into the calculation of porosity. By the pressure balancing or nulling, the free volume of the sample chamber is merely substituted by an equal and measured volume of mercury. Since the measurements are at constant pressure, there are no compressibility corrections necessary for the sample chamber.

By N. Malakouti, R. H. Whipp, O. A. Kuby, R. M. Smailer

A detailed description of the development of the FIOR process (Brown, Campbell, and Saxon, 1966) and, subsequently, other technical papers related to the operation and start up of the FIOR plant (Violetta, 1975; Whipp, 1980) are available in the technical literature. The Fluidized Iron Ore Reduction (FIOR) process plant constructed in the Matanzas region of Venezuela represents the first commercial application of this technology. The FIOR process was developed by Exxon Co. during the 1950s and 1960s. The facility in Venezuela was designed and constructed by Davy McKee, with plant start-up in 1976. While there is a minority government ownership in the company, FIOR de Venezuela operates as a private sector company with the majority of ownership being private capital. The FIOR process is well suited to utilize the naturally occurring iron ore fines of the Cerro Bolivar and San Isidro iron ore deposits located less than 100 km (62 miles) south of the plant site. Availability of natural gas within 150 km (93 miles) to the north, and a location bordering on the confluence of the Caroni and the Orinoco Rivers makes for an ideal geographic site. Feed stock to the FIOR plant consists of naturally occurring iron ore fines from these ore bodies, which are screened to -6mm (-0.2 in.) prior to drying in the ore preparation plant. A simplified flow plan is shown in [Fig. 1]. The dried ore is then transferred to the top of a structure containing four fluid-bed reactors located above one another so the mineral may flow from one reactor to the next by gravity. A reducing gas containing 90% hydrogen is made by steam reforming of natural gas, a CO shift

Jan 1, 1983

By R. C. Hassinger, D. V. von Rosenberg

Transverse dispersion has received considerably less treatment in the literature than has longitudinal dispersion. Different methods for determining transverse dispersion coefficients have been used in different investigations, and the results obtained have not been consistent enough to permit accurate generalizations as to the effect of various physical parameters on the magnitude of these coefficients. A numerical solution to the differential equation describing transverse dispersion in the absence of longitudinal dispersion was obtained to enable one to calculate the dispersion coefficient from experimental results. The more general dispersion equation including longitudinal dispersion also was solved numerically to give quantitative limits of a dimensionless group within which the assumption of negligible longitudinal dispersion is justified. Possible experimental procedures were examined, and one utilizing a cylindrical packed column was chosen for the determination of transverse dispersion coefficients. Values of these coefficients were determined for a system of two miscible organic fluids of equal density and viscosity, for two sizes of packing material over a wide range of flow rates in the laminar regime. The dispersion coefficient was found to decrease, for a constant value of the product of packing size and interstitial velocity, as the size of the packing material particles increased. INTRODUCTION Longitudinal dispersion has received extensive treatment in the literature, and consequently is better understood than its orthogonal counterpart, transverse dispersion. Many mathematical models of dispersion processes assume that transverse dispersion is rapid enough to damp out any radial** concentration gradients and therefore may be neglected. Laboratory and production results, however, indicate that this is a poor assumption.l,2 Various experimental procedures for determining transverse dispersion coefficients have been used in previous investigations, but the results have generally been expressed by similar correlations. The transverse dispersion coefficients obtained, however, have often varied considerably for given values of the correlation parameters. We feel that further experimental determinations of transverse dispersion coefficients will help alleviate some of the inconsistencies in these empirical correlations. One assumption implicit in all previous investigations is that of negligible longitudinal dispersion in the experimental system. An attempt to justify this assumption often is made using intuitive reasoning, but it is apparent that this reasoning must break down as the condition of zero flow rate is approached. A mathematical examination of the equations describing the system yields physical limits outside of which the assumption of negligible longitudinal dispersion is invalid. BACKGROUND In a porous medium, the "effective molecular diffusivity" De is less than the molecular diffusivity D measured in the absence of a porous medium, due to the tortuous path which a diffusing molecule must travel. Various authors3-5 have reported values of the ratio De/D in the range of 0.6 to 0.7. When there is fluid flow within the porous medium, mass transfer occurs by convective dispersion as well as by molecular diffusion. These are separate phenomena and can be treated as such on a microscopic scale. However, the mathematical complexity is such that only extremely simple geometries could be considered, and the results hardly would be applicable to the complex geometries existent in actual porous media. A more

Jan 1, 1969

By S. G. Cupschalk, J. J. Wert, R. A. Buchanan

The uniaxial deformation of thermally ordered and disordered polycrystalline Cu3Pt was studied by means of the X-ray line - broadening analysis according to Warren and Averbach and the extension of this analysis to ordered fcc materials by Mikkola and Cohen. Because of the heat treatment history, extinction had a pronounced effect on the X-ray spectra of ordered and disordered C%Pt at small plastic strains. After an appropriate correction for extinction, the long-range order in thermally ordered ChPt was found to decrease at a slow constant rate with plastic strain. Furthermore, the antiphase domain probability increased at a constant rate to 17.5 pct strain. The effective particle size behavior indicated that the stacking fault energy is lower in ordered than in disordered Cu3Pt. Analysis of the stress-strain curves shouled that ordered Cuzt has a slightly lower yield Point but a much higher work-hardening rate than disordered Cu3Pt. THE presence of long-range order in a solid-solution alloy has a marked effect on its mechanical properties. While this effect has been known qualitatively for many years, it was not until recently that detailed investigations have been performed to determine the exact role long-range order plays in this strengthening mechanism. The development of an advanced, quantitative. X-ray diffraction analysis by Warren and Averbachl and the extension of this analysis to the L1, type super lattice by Mikkola and cohen2 have greatly accelerated research in this field. The research reported in this paper consisted of two primary phases. The first phase was to determine the effect of long-range order on the tensile properties of polycrystalline Cu3Pt. This objective was accomplished by comparing the stress-strain behavior of thermally ordered CusPt to that of thermally disordered CusPt. The second phase of the research was to determine the difference between the atomic arrangements in thermally ordered and thermally disordered Cu3Pt as a function of uniaxial deformation and thereby gain a deeper insight into the mechanism by which long-range order affects the tensile properties. This second objective was accomplished by applying the Warren-Averbach method of peak profile analysis to the X-ray diffraction patterns obtained from ordered and disordered Cu3Pt after given amounts of uniaxial deformation. EXPERIMENTAL PROCEDURE The Cu3Pt was prepared by vacuum melting and casting. After a homogenization anneal, the ingot was cold-rolled to sheet form. Two tensile specimens with gage sections of 2.50 by 0.500 by 0.115 in. were carefully machined from the sheet. The specimens were polished with a final step of 600-grit paper to insure smooth diffracting surfaces. Finally, one specimen was heat-treated to yield an average grain diameter of 0.016 mm and an initial degree of long-range order, S, of 0.825. The other specimen was water-quenched from above the critical temperature, 645"C, to yield an average grain diameter of 0.017 mm and zero long-range order. The heat treatment history of each specimen is shown in Table I. The tensile tests were performed utilizing a Research Incorporated Model 900.95 Materials Testing System. This unit employs a closed-loop feedback system which maintains a constant strain rate through an extensometer clipped to the gage section of the tensile specimen. A strain rate of 1.32 i0.02 x 10"4 sec-&apos; was employed in testing both specimens. In the X-ray diffraction analysis, a General Electric XRD-5 diffractometer equipped with a pulse-height analyzer set for 90 pct efficiency was employed. The goniometer speed selected was 0.2 deg, 20, per min. Filtered Cu radiation was used for all peaks and all peaks were chart-recorded. Because of nonuni-form grain size. it was necessary to spin the specimens during X-ray analysis in order to obtain reproducible integrated intensities. The spinning rate was 2000 i100 rpm. The application of the Warren-Averbach method of peak broadening analysis to a diffraction pattern is very time consuming if done manually. In this research, the calculations involved were performed with the aid of a computer program by wagner.3 As reported by Wagner, the program is written in Fortran TV computer language. It was modified to Fortran I1 so as to be handled by the IBM 7072 computer at Van-derbilt University. In the X-ray diffraction analysis of uniaxially deformed Cu3Pt, the 100, 200. 400. 111, and 222 reflections were recorded from the initially ordered sample after &apos;plastic strains of 3.0, 6.0, 9.0, 12.0,

Jan 1, 1970

By Bernard K. Asdell

Georgia, a state seldom considered to be an important mineral producer, has one surprising feature-it is the nation&apos;s largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite.

Jan 11, 1967

By Sam Harlan

At intervals during the past several years the oil industry has been confronted with the problem of forestalling crises in its affairs. These crises have been reduced to periods of depression which, fortunately, the industry has been able to survive. Under the existing competitive practices which control the producing division of the industry it apparently has been proved that the best efforts logically to curtail development and producing operations are inadequate for effecting a true production balance and the consequent stabilization of prices. The industry is awakening to the fact that the situation warrants revolutionary thought and at this time it is looking for a permanent solution of its problem in a general plan for unit development and operation such as the one first proposed by Henry L. Doherty. Mr. Doherty&apos;s proposal was designed not only as a means for stabilizing the industry as a whole, but its principles involve very definite potential benefits for the average individual operator and royalty owner as participants in pooled projects. The benefits to these individuals would be derived from maximum recovery, the maximum utilization of natural energies, the minimization of development and operating costs, enhanced values of leases and royalties through improved efficiencies and ultimate yields, improved earnings through stabilized crude oil prices, etc. This plan was revolutionary to the industry&apos;s practices and at the time was rejected, but it now appears that the development and operating policies for new properties are continually approaching the ideal of the original plan. Oil companies are constantly extending their efforts to improve all factors that have a bearing on the costs and efficiencies of their operations. These efforts may, in some degree, be a normal outgrowth of the industry&apos;s progress, but the forced consideration of market conditions, the growing appreciation of the importance of regulating operations for maximum ultimate economies and the depreciation of the old principle of maximum flush at any cost, come from a new school of thought which has been stimulated by the immediate pressure of overproduction and

Jan 1, 1930

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal. The patent literature gives information on some of the methods proposed. Esselen and Weiss 1 have patented the deposition of a coloring material in the valleys of the surface of the coal. Sperr2 covers the quenching of coke with water containing a pigment or dye that will deposit on the coke. He also suggests electroplating with copper or nickel. Glinsmann 3 subjects the freshly fractured coal surface to the action of an alkali or alkali earth ferricyanide and a ferric salt. Barsky and Hanson4 specify a method for the application of the same chemicals covered by Glinsmann.

Jan 1, 1943

By R. E. Miner, J. K. Jackson, D. F. Gibbons

Internal-friction measurements were made during isothermal aging treatments of 18 pct Ni maraging-steel wires between 420° and 612°C. A sharp initial drop in the internal-friction level was interpreted in terms of a rapid dislocation recovery reaction. The rate of the recovery was found to be independent of temperature. Truncation of the recovery reaction was apparent in those systems that exhibited the rapid age-hardening characteristics of the maraging steels. It is proposed that this initial hardening response is the result of a low activation energy preprecipitation reaction involving molybdenum. A gradual rise in the internal-friction level at longer aging times was associated with the precipitation of a molybdenum-containing precipitate. CONSIDERABLE research effort has recently been devoted to the mechanisms responsible for the high strength and toughness of 18 pct Ni maraging steels. These bcc martensitic alloys are found to harden during aging at temperatures between 400° and 600°C. The aging response is very rapid with more than half the total hardness increase occurring within the first few minutes of aging, Fig. 1. Precipitate particles have been observed in the later stages of aging by a number of investigators.&apos;-&apos; While the identity of the precipitates remains the subject of some controversy, one or more of the intermetallic compounds, Ni3Mo, Ni3Ti, and Fe2Mo, are almost certainly involved. Heterogeneous nucleation of precipitates at dislocations has been noted8 and cobalt is believed to enhance the formation of fine, homogeneously distributed particles by lowering the solubility of the alloying elements in the martensitic matrix.3,7 Transmission electron microscopy studies of the initial hardening behavior have not been fruitful. Strengthening mechanisms based on atomic ordering have not been generally supported by X-ray and neutron-diffraction experiments.9 In the present investigation, the aging reaction was studied using isothermal-aging internal-friction measurements. The marked sensitivity of internal friction to short-range diffusion and precipitation processes has provided a convenient tool for the elucidation of the strengthening mechanisms operative in the maraging steels. EXPERIMENTAL PROCEDURE An upright torsion pendulum was used to measure the internal friction of several maraging steels during isothermal aging. The pendulum was placed in an atmosphere of helium at a pressure slightly less than atmospheric. To permit measurement of internal friction during the first minutes of aging, the specimens were rapidly heated by passing a current through them in a manner similar to that described by Ang and Wert.10 Thermal gradients in the specimen were largely eliminated by using specially designed specimen grips11 which produced temperature variations of less than 1 pct over 90 pct of the specimen length and less than 3 pct over the entire length at aging temperatures up to 620°C. A proportioning strip-chart program controller was employed to maintain constant specimen temperature during treatments of up to 36 hr duration. A number of vacuum-melted laboratory heats having compositions near that of a typical commercial 18Ni-7Co-5Mo-0.4Ti alloy were investigated. The amount of cobalt was varied from 0 to 7 wt pct in five of the heats. Either molybdenum or titanium was omitted in the remaining two heats. The alloy desig-

Jan 1, 1967

By Richard H. Terhune

It cannot be said that the development of processes for roasting in Utah has been evolutionary. Some of the best systems were contemporaneons with smelting here, and one of the most primitive methods, pile roasting, is still entrenched, to the exclusion of all others, at one works. This is certainly not because we have not had sulphur, in place and out of place, to contend with, but rather because roasting has not been a necessity, we having, like most other smelting districts in America, a good share of oxidized ores.

Jan 1, 1888