Search Documents

By T. M. Howell

JET piercing is a licensed process developed by Linde Air Products Co. Experiments with this method lapsed during World War II, but in the decade that followed the process was expedited. Two types of drills mount the jet piercing equipment for blastholes. The turntable of one machine rotates the complete stem system as well as the blowpipe, which emits three individual flames at different levels. Depth penetrated is limited by length of the blowpipe mounted in the rotary mechanism. This machine has successfully drilled blast- holes in Minnesota taconite.

Jan 6, 1957

By James E. Harding

The usual method of sampling mineral deposits is to drill holes and assay the sludge or core. Though the results thus obtained may not represent the true average value of the deposit, it is on these results that estimates of practically all large orebodies are made. In a large number of cases, the results of exploitation fall far short of the estimated value of the orebody. The standard method of making these estimates is to find the cubic contents of triangular prisms, in the apexes of which the drill holes are placed, by. multiplying the surface area by the average depth of the ore in the three drill holes and then multiplying the cubic contents by the specific gravity of the ore or rock to find the tonnage. The assay value is found by dividing the sum of the products of the depth of ore in each hole and the corresponding assay value by the sum of the depths of the ore in the three holes. As the latter part of this method is subject to many mathematical errors, it should not be depended on. Some engineers, therefore, use a discount factor, but as this factor is either arbitrarily selected or is obtained by obscure methods, the results are no better than guesswork. The standard method is correct when the drill holes are so laid out that the triangular prisms are equilateral in cross-section. But as ore deposits cannot always be drilled into at regular intervals and because of the human factor, if many holes are drilled, triangular prisms of all degrees of angularity are produced. In such cases it is necessary to assume that the influence of the different holes is not the same in all directions, which assumption of course is absurd. The area of the triangular prism is usually found by scaling; an ore-body of sufficient size to justify churn drilling is too large to be handled conveniently on maps having a scale larger than from 1000 to 1 to 1,500 to 1 and maps of such scales cannot be accurately measured. A variable is thus introduced in the first operation. In addition, the scaling is frequently done from blueprints, which sometimes shrink as much as 4 per cent. between printing, washing, and drying. The error due to scaling may be eliminated by surveying the location of each hole and

Jan 1, 1922

By Walter Miller

During no similar period in the development of petroleum refining technology has so much progress been made in methods and equipment for the economical utilization of heat. Drastically severe commercial and economical conditions controlling the refining industry during 1927 gave a great impetus to improved efficiency and more economical operation in all departments. I think it is fair to say, however, that more progress has been made in the department of heat utilization than in other branches. I use the word utilization advisedly in the dual sense of better primary generation and application of heat and of saving by recovery methods. It was because of this trend that the subject, "Economical Application of Heat," was made the keynote of the refinery engineering sessions just completed. No new, outstanding elemental discoveries can be claimed for the year along this line. Some of the progress made has been in the development of better furnaces and distilling equipment embodying the more modern principles of boiler practice in obtaining complete combustion of the fuel, low excess air requirements and high transfer rates through the heating surface. Transfer rates of 3000 to 6000 B. t. u. per sq. ft. per hr. were considered good some time ago in the older type of equipment. Today a transfer rate of 25,000 to 35,000 B. t. u. is an actual accomplishment in commercial installations and engineers are talking of the feasibility of 50,000, 75,000, even 100,000 R. t. u. per sq. ft. per hr. Contributing most to bringing this about have been the rational use of the velocity factor on both the oil and firing side of the heating surface, and the study and application of the principles of radiant heat in furnace design. Vapor Heat Economy The principle of heat exchange, especially against oil vapors, has been applied to a greater extent than ever before. The recovery of heat from oil vapors is not new. This was practiced 20 years ago or more in Europe,

Jan 1, 1928

By George C. Toland, Ronald E. Versaw

Most existing impoundment ponds and dams leak effluent into the soil or rock upon which they are constructed. However, proposed environmental legislation will require very stringent control of the release of toxic effluents such as cyanide. More exacting investigation, design, and construction techniques than have been used in the past will be required to satisfy these new regulations. The types of field and laboratory investigations required to develop the data for the design of an impoundment system containing toxic effluent are discussed, together with the technical considerations necessary to design this system. Design topics include reservoir sealing with natural and man-made materials; embankment sealing; embankment design considering stability, surface hydrology, capacity, and downstream catchment basins; and special implications of cyanide effluents.

Jan 1, 1977

Jan 4, 1951

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute In the aggregate, the amount of these endowments totals more than $830,000 An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which Harvey S Mudd is Chairman, and

Jan 1, 1952

By Alan D. Smith

Mine roof fall characteristics of 250 falls in 5 different room-and-pillar coal mines, located in Pike, Martin, and Floyd counties, were investigated to determine the relationship of selected parameters associated with roof failure and the assumed condition of the mine roof before failure. The selected parameters used in the study included: presence of cracks and water before the occurrence of fall, sloughing of coal ribs, floor heave condition, type of roof support (resin or mechanical anchor bolts), distance to coal face, and time of occurrence of fall after initial coal extraction. In addition, research hypotheses, utilizing multiple linear regression techniques, were generated to test the relationship among the selected parameters and mine roof condition. The results indicated that the vast majority of falls portrayed some presence of water before the actual fall, occurred in less than 30 weeks after initial coal excavation, located usually greater than 30 meters from nearest coal face, gave evidence of cracks in mine roof before occurrence of fall, generally portrayed a good roof condition before the fall, showed presence of sloughing of coal ribs, and gave no occurrence of floor heave before occurrence of fall. In terms of the characteristics of the original support systems in the mine roof falls studied, most roofs were either supported by mechanical-anchor bolts or resin or full-column bolts; very rarely did the roof appear to fail if supported by posts or cribs. A detail inspection of the hypothesis and model comparison results gave supporting evidence that the condition of the roof is not dependent on the usual indicators of potential failure, such as presence of cracks and moisture. In fact, in most cases of mine roof failure, the immediate roof condition was rated as good or better, which gives little or no indication of pending failure and collapse. Hence, a combination of factors that are not easily accessible to measurement, are the dominant factors in the determination of roof fall-potential areas.

Jan 1, 1984

By Donald P. Bellum, Lee Nugent

Southwestern Utah is well known for its scenic attractions. The beauties of Bryce Canyon, Zion Canyon and the Grand Canyon are of world renown. Thusly, Cedar City is known, at least by the local Chamber of Commerce, as the Gateway to the Utah Parks. However, of the thousands of tourists flocking to Utah's many points of interest by way of Cedar City, few realize that any mining takes place in the vicinity, in spite of the fact that iron mines have been in continuous operation for 40 years. The Pinto-Iron Springs Mining District is only 15 miles west of Cedar City, and is the largest iron ore producing district in the West. In recent years, the shipments have ranged from 2% to 4 million tons per year making Utah the fifth-ranking state in iron ore production.

Jan 11, 1963

By H. M. Howe

The tenacity with which a bad name adheres to a process is well illustrated by the prevalent belief in the irregularity of the product of the Bessemer converter. We have been lately told by an eloquent member that lack of uniformity is the name of Bessemer steel, and that uniform soft steel can only be made in the Clapp-Griffiths Bessemer converter. Yet I believe that, however irregular the percentage of carbon in Bessemer steel may have been formerly, to-day it is well-nigh completely under control. Indeed, the results of a large number of analyses that I' have studied go to show that the

Jan 1, 1887

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By George F. Comstock

It has been reported recently1 that the hardenability and toughness of forging steels may be improved appreciably by the use of complex deoxidizers containing titanium, aluminum, and vanadium. In the light of these results, an investigation of similar deoxidizers containing various hardening and grain-refining elements was proposed. These deoxidizers included three manganese-silicon-aluminum-titanium al- loys with and without boron and calcium, three titanium-aluminum ferroalloys with vanadium, molybdenum and zirconium, respectively, an aluminum-zirconium ferroalloy, and plain ferroboron. Their approximate compositions are given in Table I, and the results obtained so far in the investigation of their effects on steel are presented in the later parts of this paper. Method of Using Deoxidizers The deoxidizers listed in Table I were used in three series of 0.40 per cent carbon steels, which were melted in a small basic-lined induction furnace and cast in the form of I7-lb. ingots about 2.75 in. square. The basic charge for each heat was 10 lb. Armco iron and 6 lb. of clean low-carbon sheet-steel scrap. When melted, this charge was deoxidized with 15 grams of ferrosilicon, then about 500 grams of pig iron was added to give the desired carbon content. After the pig iron was dissolved, nickel shot and high-carbon ferrochromium were added if required, and additions of 80 per cent high-carbon ferromanganese and 50 per cent ferrosilicon were made to provide the proper amounts of those elements. Aluminum was added to every heat 2 min. after the silicon, for grain-size control and preliminary deoxidation. One minute later the special deoxidizer was added to the clean bare surface of the molten steel, and 2 min. afterward the steel was poured into the ingot mold, using a hot-top and pipe-preventing compound after pouring to decrease the depth of the shrinkage cavity. The special deoxidizers were used mostly in the form of about ½ to¾-in. lumps,

Jan 1, 1942

By J. G. Puterbaugh

MARCH 31, 1922, undoubtedly will be long remembered as the ending of an important epoch in the coal-mining industry. On that date, contracts fixing the wages and terms of employ-ment at all anthracite mines and at approximately 60 per cent. of the bituminous mines of the country expired. For the past two years, the consuming public has been complaining bitterly against continued high cost of coal. Coal operators employing union labor have felt obligated to carry out contracts entered -into under the direction of the Bituminous Wage Commission appointed by President Wilson, and in order to do this, they have sacrificed millions of tons of business to non-union mines, and millions of dollars in wages that would have been distributed throughout unionized districts have been diverted to the non-union miners, many of whom never obtained the peak wages granted by the Bituminous Commission and others of whom accepted reductions early in 1921. Heretofore, wage contracts have overlapped as to expiration dates in different districts and renewals have had to take into consideration the competitive balance; the present situation is unique in that practi-cally every contract in the country expired on March 31, and the questions now confronting those responsible for the operation. of the coal mines of the country are: 1. Shall the operators that have heretofore employed union labor endeavor to continue contractual relations with United Mine Workers of America? 2. Shall they undertake to operate their mines with non-union labor? 3. Shall they encourage and endeavor to work out some plan of regulation or arbitration by a Government commission such as President Roosevelt appointed to settle the anthracite strike in 1902? 4. Shall the country give consideration to the demand of the miners that the coal-mining industry be "nationalized?"

Jan 5, 1922

By Sam F. Carter

FOR some time melters and metallurgists have recognized the fact that steels may be made to identical compositions as ordinarily analyzed, but with considerable variations in physical properties. Good melting practice signifies a combination of furnace operations that will produce steel with consistently good physical properties after proper consideration of cost, production efficiency, and chemical control. In acid practice, these operations may be classified fundamentally as: (I) the oxidizing boil, (2) recarburization and deoxidation, (3) slag adjustment, and (4) final deoxidation. These operations affect the properties of the steel through variations in the minute quantities of several microscopic, submicroscopic, and dissolved constituents, which are out of reach of ordinary analyses but are very influential upon the crystallographic slippage and the molecular cohesion of the structure. One of these constituents is the FeO left in solution in the steel. Herty has shown that steels high in dissolved FeO have decreased ductility and impact and increased hardness and electrical resistance. There is also much evidence that FeO in solution affects carbon solubility and diffusion, and consequently abnormality and carburizing behavior.

Jan 1, 1947

By James M. Barker

Jan 1, 1985

By B. H. Caudle, R. E. Watson, I. H. Silberberg

The production history of an inverted nine-spot injection pattern was studied with a porous plate model similar to Habermann's. Colored fluids were used so the boundary movements could be photographed. By varying the production rates of the side and corner producing wells, the optimum pattern sweep efficiency can be obtained. Results of the laboratory tests indicate that interpolation of the pattern sweep and conductivity ratio data will permit application of the data to predicting fluid injection operations with mobility ratios between 0.1 and 10 and production rate ratios between I and the optimum values. INTRODUCTION The inverted nine-spot injection pattern in Fig. 1 has some unique advantages over other regular injection patterns (five spot, line drive, etc.) used in secondary recovery operations. It has three producing wells for each injection well, while the five-spot and line-drive patterns require an equal number of injectors and producers. Futher-more, of the eight producing wells surrounding each injection well, four are of the "side well" type which lie nearer the injection well than the remaining four "corner wells". This allows the production rates of these two types of wells to be adjusted independently of each other to obtain better pattern sweep efficiency. This latter advantage may well be the reason why the nine-spot patterns have not been studied as extensively as the patterns containing only one type of injection or producing well. The pattern sweep efficiency of the inverted nine spot is affected almost as much by operating with different producing rates of the comer and side wells as by differing mobility ratios. Possibly because of this added operating parameter, published studies of nine-spot systems have been limited in their coverage of the pertinent variables.'-' The model studies reported here covered the mobility-ratio range normally found in waterflood operations, as well as the variation in well production rates necessary to achieve optimum pattern sweep efficiency. Conductivity ratios — a measure of the change in total flow at constant pressure difference — were obtained during each model run. A porous-plate model with miscible fluids representing the in-place and injected fluids was used in this study. This model technique is the same as that used in both X-ray shadowgraph" and visual techniques4 described in the literature. Using miscible fluids eliminates residual oil in the model, and the permeability to the injected fluid is the same as to the in-place fluid. Thus the mobility ratio in the model is given by the ratio of the viscosity of the displaced fluid to the viscosity of the injected fluid. Because of the non-linear nature of the viscosity vs composition curve for two miscible liquids, the mobility change across the boundary between the two fluids is reasonably sharp. This technique thus represents the displacement of a region of one fluid mobility by a region of possibly different mobility in an isotropic system under steady-state flow conditions. Table 1 shows the dimensionless similarity groups used to scale the model conditions and results to

Jan 1, 1965

By Carroll Wegemann

THAT Colorado was producing oil and gas before the fields of the Mid-Continent were discovered is a fact too frequently overlooked. As early as 1862, oil was obtained in the Florence district (see Fig. 1) from seepages and shallow holes. The first well that could be regarded Fig. 1. as being truly commercial was drilled in this field in 1876. The field is now producing 100,000 bbl. per year, and is credited with a total production of approximately 11,000,000 bbl. The small field near Boulder, Boulder County, was opened in 1901; production has now practically ceased but the field is credited" with a total production of 610,000 bbl. Oil was discovered at Rangeley in 1901, and the field supports a small local refinery at the present time. The first shallow well in the White River gas field was drilled in 1892, and the wells now producing have been

Jan 3, 1925

By A. Sainato, E. Baker, J. Cervik

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the US is limited to a few plow operations in the deeper parts of the Pocahontas No. 3 Coalbed. The technology for infusing water into retreating longwalls is described and results of a recent Bureau test in the Lower Sunnyside Coalbed demonstrated dust reductions ranging from 47% to 64%. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 2.5 m/s (500 fpm) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23% reduction in operating costs when coal production is increased by changing from unidirectional to bidirectional mining with water infusion.

Jan 1, 1986

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923

By M. Mathieu

The Rove tunnel is the means by which the canal from Marseilles to the Rhone Riverl penetrates the hills of Nerthe, lying between Mar- seilles harbor and Lake Berre, Fig. 1. The canal will communicate at sea level with both terminals. The original project planned a lock near the village of Marignane; but observations, pursued for more than three years, showed that the water surface gradient would average only 0.015

Jan 1, 1923

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972