Search Documents

By Henry A. Wriedt, John Chipman

Equilibrium in the reaction of hydrogen gas with oxygen in liquid nickel, iron, and their alloys has been studied at temperatures of 1500° to 1700°C. The equilibrium con^stant, 0/p, [% O], is greater in nickel then in iron by a factor of 45 at 1594 C. In the alloy steel range, the activity coefficient of oxygen is slightly increased by the presence of nickel. NICKEL is more resistant to oxidation than is iron, in both the solid and the liquid state. The solubility of oxygen,' however, is greater in nickel than in iron. The two metals and their liquid alloys constitute an interesting series of solvents in which the chemical behavior of oxygen can be studied by methods similar to those used for liquid iron.' Experimental Method The furnace assembly, including the tube for preheating the entrant gas, was the same as that described by Gokcen and Chipman. " controlled mixture of water vapor, hydrogen, and argon preheated to approximately the melt temperature impinged upon the surface of the liquid metal. The charge, weighing about 35 g, was held in an alumina crucible at constant temperature in the gas stream for a prolonged period, then quenched in a stream of cold helium, sampled, and analyzed for oxygen by the vacuum fusion method. The temperature of the liquid metal was measured by a Leeds and Northrup optical pyrometer which had been checked against a similar instrument certified by the National Bureau of Standards. The freezing point of electrolytic iron in hydrogen, taken as 153j°C, was used for frequent checks. This point and the emissivity determined by Dastur and Gokcen" established the transmissivity of the optical system. The emissivities of Fe-Ni alloys at 1535" are known from the experiments of Smith and Chipman,h nd it was assumed that the variation with temperature is parallel with that of iron. Recorded temperatures are probably accurate within k5"C. Preparation of Gas Mixtures—Since the ratio H,O:H, had to be much higher for nickel than for iron, it was found convenient to construct two separate systems for gas preparation. In both cases, the ratio of argon to the sum of the other two gases was at least 4, the proportion of hydrogen and water vapor being varied to produce H,O:H, ratios from 0.2 to 70. The primary purpose of the argon was to diminish the errors caused by thermal separation' in the gas phase. In addition, its presence lowered the saturation temperature required for a given H,O:H, ratio and minimized the difficulty of preventing condensation. Both systems were modifications of the one used by Dastur and Chipman.' For H,O:HI ratios greater than 2, welding-grade argon purified by passage over magnesium chips at 620°C was mixed with hydrogen produced in the electrolytic cell shown in Fig. 1. The design was based on a cell used by Bodenstein and Pohl," the important features of which area nickel wire cathode and sodium hydroxide solution as the electrolyte. The rate of hydrogen evolution was controlled by a calibrated ammeter and a rheostat in the circuit, the current efficiency being taken as 100 pct. Precise control of the argon flow rate at about 300 ml per min was achieved by means of a capillary flowmeter having a controlled pressure drop. The molar flow rate was measured volumetrically before each run, and a constant flowmeter setting was maintained thereafter. The A-H, mixture passed through a water saturator of the type previously described," the saturation temperature being maintained automatically with a fluctuation of k0.04"C. The tube between saturator and furnace was heated by a resistance winding. The system was of all Pyrex construction with the exception of the stainless steel tube containing magnesium chips. This was connected with the glass tubing at the upstream end by

Jan 1, 1957

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-' proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible 'References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By H. W. Winkler, Discussion, V. L. Forsyth

The development of a new gar lift valve has removed many of the obstacles limiting over-all gas lift efficiency. The valve is pressure charged in place in a well, and operating pressure can be changed without pulling. Temperature and gas gradient compensation have been eliminated. Intermitting and constant flow installations, using conventional pressure-charged valves, are compared with designs incorporating the new automatic stabilizer controlled valve. Specific well performance data are presented. The means of obtaining and controlling multiple-point injection of gas are explained and contrasted with single point injection. The effect on small diameter strings and multiple string installations is discussed. The effect of flowing temperature gradient on a design using conventional pressure-charged valves, the limitations imposed by such temperature, and the obvious benefits which result from the use of automatic stabilizer controlled valves are shown. Reduction of gas requirements is stated mathematically and demonstrated with specific examples which are identified as to oil company and well. Increased fluid recovery resulting from greater drawdown is illustrated. The economic advantages are mentioned with emphasis on reduction of capital expenditures, as well as reduction in operating expenses. INTRODUCTION Much of the engineering and research work performed with gas lift has been based upon the supposition that under producing conditions gas would be injected at a single point in a well. Many tests were performed in determining the optimum size of the opening through which gas would be passed and the exact placement of the valve equipment. The objectives in a gas lift installation are to unload the well and to efficiently produce the well after it is unloaded. Until recently, the function of upper valves was simply to unload the well. An operating valve located at a proper place in a well served as a single injection point for lifting liquid to the surface. The basic problem in using such equipment is to arrive at operating depth with sufficient operating pressure to efficiently lift the liquid. Few gas lift installations are designed with all required well data available. However, regardless of the quality and availability of data, and regardless of the accuracy of the design, there is the practical problem of preparing and placing gas lift equipment in the well in exact accordance with the plans and intentions of the engineer. In recognition of these and many other problems, attention was directed toward a means of removing the need for temperature and gas gradient compensation, a way to change the gas lift installation to meet the changing requirements of the well itself, and a manner of compensating for changes in oil-water content, fluid volumes, PI, and bottom-hole pressure resulting from flood or repres-suring activity. A device which could actually set and change the operating pressure of gas lift valves in the well would meet most of these needs. There now exists a new gas lift valve which fulfills the original objectives and in so doing actually accomplishes much more. With this device, called an Automatic Stabilizer Controlled valve, there is an exact matching of valve operating pressure and well conditions. Gas is injected at more than one point in the well, thereby making controlled multiple-point injection of gas a reality. Installation calculations are materially simplified and the need for basic temperature and gas gradient data no longer exists. Section I—The Automatic Stabilizer Controlled Valve The operation of the ASC valve is more easily understood by first studying a conventional pressure-charged valve and then inserting the stabilizer element to observe the changes which result. Fig. 1 is a schematic of a conventional precharged pressure-operated valve. The pressure in the dome pd, acts downward, against the area of the bellows A,, to hold the valve closed. The resulting force Bf plus the spring effect of the bellows Sf represents the total force acting to close the valve. Correspondingly, the tubing pressure ptbg works upward against the port area Atbg and the casing pressure pc works upward against a portion of the area of the bellows

Jan 1, 1965

By J. C. Fisher, J. H. Hollomon, David Turnbull

Understanding of the diffusion problem has recently been furthered by the analysis of Birchenall and Meh1.l They pursued the problem of the variation of the diffusion coefficient with composition for non-ideal solid solutions. Their analysis follows the tradition of Wagner,l Jost, Dehlinger, and Darken & who assumed the net flux of diffusing material to be proportional to the gradient of a quantity related to free energy. The basic assumption in Birchenall and Mehl's formulation of the problem is that the net flux of diffusing material is proportional to a thermodynamic activity gradient. To estimate the applicability of the derived relations, they corrected the diffusion coefficients of carbon in austenite by utilizing Smith's6 activity data for carbon, and the diffusion coefficients for zinc in copper with activity data computed from the vapor pressure measurements of Har-greaves.' The corrected coefficients for carbon were virtually independent of carbon concentration. For the diffusion of zinc in copper a moderate variation of diffusion coefficient with concentration remained after the correction. The problem of diffusion can be formulated in another way than that used by Birchenall and Mehl. The method is that of chemical rate theory and has been used by Eyring and his coworkers8,9 as well as by Eyring and Zwolinskilo in a discussion to Birchenall and Mehl's paper. As yet the method has not been applied to substitu-tional solid solutions. On the basis of their assumptions, Eyring and Zwolinski derived a relation between the diffusion coefficient and activity that is identical with that of Dehlinger and Darken but which does not correct for the variation of the diffusion coefficient with concentration as well as does the relation derived by Birchenall and Mehl. It was thought that the theory of diffusion would be more complete if the inconsistency between the two analyses could be rationalized and if diffusion in substitu-tional alloys were analyzed on the basis of the concepts of the chemical rate theory. Chemical Rate Theory According to the theory of absolute reaction ratess the reaction +..... +X, Eq I is viewed as taking place in two steps. First the reactants A1, A², . . . A; combine to form an activated complex M with which they are in equilibrium: A1 + A1+ . . . + A=M. Eq 2 Second the activated complex decomposes to give the products XI, XZ, . . . Xi: M?X, + X²+ . . . +Xi Eq g It has been showns that the number of activated complexes decomposing per unit volume per unit time is given by the expressiont kT -h CM † The transmission coefficient has been taken as unity.

Jan 1, 1949

By David Turnbull, J. H. Hollomon, J. C. Fisher

Understanding of the diffusion problem has recently been furthered by the analysis of Birchenall and Meh1.l They pursued the problem of the variation of the diffusion coefficient with composition for non-ideal solid solutions. Their analysis follows the tradition of Wagner,l Jost, Dehlinger, and Darken & who assumed the net flux of diffusing material to be proportional to the gradient of a quantity related to free energy. The basic assumption in Birchenall and Mehl's formulation of the problem is that the net flux of diffusing material is proportional to a thermodynamic activity gradient. To estimate the applicability of the derived relations, they corrected the diffusion coefficients of carbon in austenite by utilizing Smith's6 activity data for carbon, and the diffusion coefficients for zinc in copper with activity data computed from the vapor pressure measurements of Har-greaves.' The corrected coefficients for carbon were virtually independent of carbon concentration. For the diffusion of zinc in copper a moderate variation of diffusion coefficient with concentration remained after the correction. The problem of diffusion can be formulated in another way than that used by Birchenall and Mehl. The method is that of chemical rate theory and has been used by Eyring and his coworkers8,9 as well as by Eyring and Zwolinskilo in a discussion to Birchenall and Mehl's paper. As yet the method has not been applied to substitu-tional solid solutions. On the basis of their assumptions, Eyring and Zwolinski derived a relation between the diffusion coefficient and activity that is identical with that of Dehlinger and Darken but which does not correct for the variation of the diffusion coefficient with concentration as well as does the relation derived by Birchenall and Mehl. It was thought that the theory of diffusion would be more complete if the inconsistency between the two analyses could be rationalized and if diffusion in substitu-tional alloys were analyzed on the basis of the concepts of the chemical rate theory. Chemical Rate Theory According to the theory of absolute reaction ratess the reaction +..... +X, Eq I is viewed as taking place in two steps. First the reactants A1, A², . . . A; combine to form an activated complex M with which they are in equilibrium: A1 + A1+ . . . + A=M. Eq 2 Second the activated complex decomposes to give the products XI, XZ, . . . Xi: M?X, + X²+ . . . +Xi Eq g It has been showns that the number of activated complexes decomposing per unit volume per unit time is given by the expressiont kT -h CM † The transmission coefficient has been taken as unity.

Jan 1, 1949

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By Edward Keller

THE ASSAY FOR COPPER. SOMEONE some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The. writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he :feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample 1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2, g. of copper) measured out for the electrolytic deposition; in the other Method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed -a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 8, 1913

By E. M. Norris

During the winter and spring of 1917, an unprecedented number of underground fires occurred in the Butte district. With one exception, these fires were caused by the failure of electrical equipment, and called attention to the increased fire hazard in underground mining operations occasioned by the extensive use of electricity. Five local conditions that contributed toward a heavy fire risk were: (1) The heavy continuous timbering necessary for mine supports; (2) the strong ventilating pressures in the shafts and main airways; (3) the subsidence and faulting movements in the country rock, which ruptured cables and displaced trolley and lighting wires; (4) the strongly acid mine waters, which quickly developed any weak points in the electrical insulation; (5) oxidation in old stopes containing large amounts of timber. In the summer of 1917, a comprehensive plan of fire prevention was begun by the Anaconda Copper Mining Co., which involved a thorough and intensive development of the preventive measures then in use. These were as follows: Fireproofing, remodeling and strengthening electrical insulations, extension of underground water system, control of ' ventilation, maintaining efficiency of fire-fighting crews, and reorganization of fire patrol. In considering the problems of fireproofing, it was immediately apparent that some method of applying a durable coat of fireproof material to the mine timbers was needed. The first experiments were made with a plaster composed of one part cement, one-half part fireclay, and three parts sand. This was applied by hand to a thickness of 1 in. (2.5 cm.) over a reenforcement of herringbone metal lath. It made a very satisfactory covering for fan stations, but was too soft and friable for traveling ways, where it was subject to abrasion. The cement gun was tried next with a three to one mixture of sand and cement. A 1/2-in. coating of gunite applied over poultry netting or metal-lath reenforcement proved

Jan 1, 1923

By Nathaniel Arbiter, Edward L. Vickers

Complete automation of concentrator operations through computer control has been under increasing consideration by American engineers for several years. Although justification for full-scale automation of a mill must ultimately be economic- added profits exceeding instrumentation and development costs-the technical feasibility of automation will be determined by the availability of requisite, detailed knowledge of the various unit operations in the plant. This poses problems. BASIC PROBLEMS WHICH MUST BE CONSIDERED A hypothetical porphyry copper mill will be used here to illustrate these problems. Its flowsheet will involve: mining, crushing, storage, grinding and classification, flotation, product de-watering, and disposal.

Jan 8, 1962

By Thomas Carnahan

THE mining property of the Utah Copper Co. is situated in the West Mountain mining district, Salt Lake County, Utah, in the Oquirrh Range of mountains. GEOLOGY In a general way the rock formation of the district consists of a series of beds of quartzite and limestone intruded by a body of monzonite porphyry roughly elliptical in shape, with an east-west axis over a mile in length and a north-south axis of about 3,000 ft. This porphyry intrusion, accompanied by strong mineralizing action and fracturing, resulted in the formation of orebodies in the adjacent sedimentary rocks, and was itself sufficiently mineralized to make it one vast orebody. The Utah Copper Co.'s mining property comprises within its boundaries practically the entire outcrop of the monzonite mass, of a commercial grade. GENESIS OF PORPHYRY ORE Following an intricate system of fracturing, mineral solutions circulated freely through the porphyry, depositing small quantities of copper and iron, and resulting in a considerable silicification of the monzonite. The quantity of copper originally deposited was undoubtedly too small to have ever given the porphyry a commercial value, had not secondary enrichment, due to the leaching of the copper from the surface of the mass and re-deposition in the sulphide zone, been active over a long period of years. A large portion of the leached material has probably been .removed by erosion, but there still remains a blanket of leached and oxidized porphyry of varying thickness covering the sulphide ore, known as capping. Over certain sections of the orebody, this capping contains commercial quantities of copper carbonates, but most of it contains little or no copper.

Jan 1, 1916

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Lang

The paper is a summary of information on Canadian deposits of uranium and thorium up to the end of 1948, prepared by geologists of Eldorado Mining and Refining Ltd. and by the specialist on uranium deposits for the Geological Survey of Canada. The paper contains a history of Canadian uranium and thorium discoveries, a working classification of the deposits, fairly detailed descriptions of the Eldorado mine and of properties in northern Saskatchewan, and shorter accounts of several other discoveries.

Jan 2, 1950

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By Louis Moyd

The Concrete Research Division, U.S. Corps of Engineers, has developed a simple procedure for determining the coefficients of linear thermal expansion of rocks by means of resistance wire (SR-4) strain gauges. Gauges are cemented to the surfaces of specimens, which are then brought alternately to temperatures of 35OF and 1350F. Results are accurate to the seventh decimal place. IN the course of investigations of the thermal properties of various rocks proposed for use as aggregates in concrete structures, a relatively rapid method of determining coefficients of linear thermal expansion was required. A method which proved to be satisfactory for this purpose was developed in the petrographic laboratory of the Concrete Research Division, U.S. Corps of Engineers, at Clinton, Miss. The method is based on the fact that strain effects in a specimen can be determined by measuring variations in the resistance of an electrical conductor firmly cemented to the surface of the specimen. Equipment for the determination of strain, electrically, has been developed by the Baldwin-South-wark Division of the Baldwin Locomotive Works in Philadelphia. This equipment includes small strain gauges made of coils of resistance wire bonded between thin sheets of paper (SR-4 gauges), and a portable "Strain Indicator" which records variations in the length of the gauges in microinches per inch. Gauges of this type are now in general use for determinations of various mechanically-induced strains, but their use for the determination of coefficients of thermal expansion appears to be a new application. The advantages of the method are that the test specimens may be relatively small and require only a minor amount of preparation, that a large number of tests can be run at the same time, and that the installation and operation of the equipment is relatively simple. The method and equipment described are now in regular use for determining the coefficients of linear thermal expansion of rock samples submitted to this laboratory. Rocks which have been tested include granites, syenites, gabbros, and other igneous rocks, limestones and dolomitic limestones, sandstones, and quartzites. Specimen Preparation: To standardize the conditions of the tests, the rock specimens are sliced by diamond saw into slabs about 11/2x11/4 in. In the case of bedded or foliated rocks, three oriented slabs are cut from the same specimen, and represent, respectively, a direction in a plane of the bedding or foliation of the rock; a direction along the bedding or foliation and at a right angle to the first; and a direction across the planes of bedding or foliation. One of the large surfaces of each slab is lapped for a few minutes with No. 100 abrasive powder to remove saw scars and irregularities. The slabs are soaked in petroleum ether and then dried in an oven to remove all traces of oil picked up in the sawing

Jan 1, 1951

By G. E. Murray

Lead blast-furnace work at Trail is unique in that this is the only plant in the world where blast-furnace smelting on a large scale for both lead and zinc recovery is carried on under one management. On this account the factors that determine economic practice differ from those of other lead smelters. In addition to this different metallurgical outlook, a great deal of structural investigation has been carried on, which has resulted in the development of a furnace which should prove of interest to all who are faced with similar problems. This description may be conveniently divided into various heads as follows: (1) General—make-up of charge, etc.; (2) structural—(a) hoods and charging methods, (b) shaft construction, (c) crucible construction; (3) handling slag; (4) handling bullion; (5) metallurgy. The Charge The Trail plant is an old one, on a congested site. As with most old plants, this limits the method of charge preparation. In general, lead metallurgists will agree that sinter when it reaches the blast furnace should contain as small an amount as possible of actual fines. There would be some difference of opinion as to the maximum size as well as of the minimum required, but to obtain the optimum condition some form of screening is indicated. This screening should take place immediately before the blast furnace if possible, and because sinter deteriorates in storage there should be as little as possible. There should also be the minimum amount of handling between the sinter machines and the furnaces. Unfortunately, at Trail the sinter must be handled considerably before it is charged to the furnace, and no feasible scheme of screening has yet been devised. Trail practice, then, demands that the sinter be a strong one physically. Dependent upon the amount of lead in it, it has been found advantageous to incorporate granulated slag into the final sinter, the amount varying inversely as the lead content. The addition of this slag makes a harder sinter, which arrives at the blast furnace in a better condition, but it entails some lack of efficiency, because desulphuriza-tion is not so rapid nor so complete.

Jan 1, 1937

Jan 1, 1923

By L. A. Geoffrion, R. H. Perkins, J. C. Biery

Densities of cerium metal and several lour-melting binary cerium alloys were measured over the range 25° to 800°C. A rolumeter, using NaK as working fluid, was used to obtain the data. The cerium, Ce-Co, Ce-Ni, and Ce-Cu alloys all exhibited an increase in density on melting, while a Ce-Mn alloy expanded on melting. FOR the proper design of a nuclear reactor, the change in density of the fuel with temperature must be known. This is especially important in a system utilizing molten fuel, such as LAMPRE (Los Alamos Molten Plutonium Reactor Experiment), since a relatively large change in density usually occurs during the solid-liquid transition. The fuel for LAMPRE is a Pu-2.5 wt pct Fe alloy with a melting temperature of 410°C. However, limitations in reactor design with this fuel have led to consideration of other plutonium-containing alloys for use in future generations of this type of reactor. Several ternary alloys containing plutonium and cerium as two components have satisfactorily low melting points. The system that at the present time appears to be most acceptable is Pu-Ce-Co; it exhibits little change in melting temperature with wide variation in plutonium concentration. Other alloys that have received some consideration contain nickel, copper, and manganese as the third constituent. The proposed fuel alloys are difficult to handle experimentally in the 25" to 800°C temperature range since they oxidize readily, react with many solvents, and contain a poisonous fissionable material. In addition, in this temperature range the alloys pass through the solid-liquid transition. Several techniques are available for measuring the densities and volume coefficients of expansion of solids or liquids. However, the only apparatus that appears suitable for measuring expansion coefficients over this temperature range and through the phase transition is a volumeter. In a volumeter, the indicating medium must be essentially inert to and insoluble in the material being studied. It must also possess a low vapor pressure over the operating temperature range, and its coefficient of expansion must be accurately known. One material that is satisfactory in nearly all of these respects is the alloy Na-78 wt pct K, which melts at -10°C and has a vapor pressure of 860 mm Hg at 800°C. This relatively high vapor pressure at 800°C requires an overpressure of an inert gas to prevent boiling. While a volumeter is capable of determining accurately the volume coefficients of expansion of materials, it cannot be used for absolute density measurements. Therefore, a density determination at a known temperature must be coupled with the volumeter measurements to give all the desired data. The weight-loss technique using immersion in bromobenzene at room temperature proved to be satisfactory. The preliminary work that was done on this experimental program involved developing and calibrating the equipment, and measuring the densities and volume coefficients of expansion of cerium and some low-melting binary cerium alloys. The complications that are caused with the introduction of plutonium into the system were avoided until the equipment was proved to be satisfactory and until experience was gained in its operation. It is this first phase of the experimental work that is described in this report. DESCRIPTION OF EQUIPMENT AND OPERATING PROCEDURE The NaK volumeter is shown schematically in Fig. 1. Basically, the equipment consists of two weld-sealed stainless-steel containers of nearly identical volume. One container holds a tantalum crucible and the specimen being measured; the other contains a tantalum crucible and a tantalum specimen used as a control reference material. To avoid temperature gradients, the bombs are located in a copper block inside the furnace. Stainless-steel capillaries of equal length and volume connect each stainless-steel container to a glass viewing capillary. The stainless-steel containers, stainless-steel capillaries, and a portion of the glass capillaries are filled with NaK (22 wt pct Na-78 wt pct K). The NaK/gas interface in the glass capillary is viewed with a cathetometer which is accurate to *0.5 mm. The cathetometer readings are used to calculate the volume changes of the samples during a run. This volumeter is basically the same as that described by F. Knight in Plutonium 1960. 2 However, changes in equipment design and operating procedure were made to eliminate some major operating difficulties. These changes are summarized below. 1) In filling the manometer with NaK, gas was frequently entrained in the system. Evacuation of the system before filling failed to eliminate the en-

Jan 1, 1965

By Lewis Delano

IT HAS been generally recognized that, owing to the extreme friability of, galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth retreating today. Investigations of the work of the Hancock jig on the Bonne Terre ore- have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average over all conditions and grades of ore will be between .0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increased smelting charges; due to a greater amount of slime galena will be counterbalanced by the lower operating cost, in-creased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the' St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various flow sheets, and to calculate the economics of the problem' with great accuracy. .

Jan 8, 1920

By T. E. Schmieman, J. E. Miller, M. L. Rizzone

Both centrifugal and reciprocating-type pumps have been widely used in the transport of slurries. Although with some limitations, centrifugal pumps may be used, especially for short-haul systems, however, for the long pipelines the reciprocating pumps are better suited. A state-of-the-art review is presented in which a discussion of applications is made and some of the problems associated with meeting the proper design conditions for satisfactory service are discussed. Several developments underway give considerable promise of better pumps in the future, although the current level of development provides for an economical means to move slurries. The movement of liquids in pipelines necessarily occasions the use of pumps. The petroleum industry is familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well, the circulating fluid utilized to remove drill cuttings is called drilling mud. This substance is usually a fairly sophisticated material designed to develop certain characteristics desirable in the drilling process. The cuttings are suspended in a moving column of this fluid and brought to the surface. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits; however, it is impractical to remove the cuttings completely and as a result they are pumped through the mud pumps back into the circulating stream. Over the years, mud pumps have been improved so that rather long life can be obtained from liquid end parts subject to the attritional effects of the abrasive-laden fluid. It is from this background that reciprocating-type slurry pumps have been developed. Centrifugal Pumps Centrifugal pumps have also been used to transport solids, where low heads are required, typically up to 200 ft or so, and for short hauls. The centrifugal pump is a hydrokinetic device wherein the increase in velocity of a fluid stream is converted to head, and to achieve high heads a large change in velocity is necessary. Abrasive laden fluids cause wear on impellers and casings as a result of erosion by the fluid and the suspended particles. Centrifugal pumps, therefore, can only be used where the internal velocity of flow is rela- tively low. The advantage of centrifugal pumps is their high capacity at relatively low capital cost and usually relatively small space requirement. One of the disadvantages of the centrifugal pump when used in slurry pipelining can be seen in its typical pressure-volume performance relationship, which tends to work against the application (see Fig. I). If an increase in pressure (head) is occasioned by flow restrictions in the pipeline, say by the dropping out of solids, a desirable characteristic of a slurry pump would be that it develop increased pressure to overcome the restriction. The centrifugal pump provides the increased pressure only at the expense of considerably reduced volume which then results in a lower flow velocity. With the reduced flow rate, adequate velocity to hold the material in suspension and keep it flowing in the line might not be achieved. If centrifugal pumps are considerd for the movement of solids in a long line, a series of pumps must be staged in order to provide the necessary motivating force. A large number of pumps in the line would be required, since each of the pumps could provide only a small pressure increment. An equal number of standby pumps

Jan 1, 1971