Search Documents

By R. M. Rose, D. P. Ferriss, J. Wulff

The effect of orientation on the stresses, nctivation energies, and activation volumes for yielding and plastic flow of tungsten single crystals was investigated. Tensile tests showed the proportional limit to be a function of orientation: crystals whose tensile axes were near the [I10} direction were roughly three times as strong as [loo] crystals. The [ 1101 crystals showed low strain hardening and displayed yield phenomena, whereas the other orientations yielded smoothly and showed considerable strain hardening. The fracture mode was cleavage, except for crystals near the [1101 , many of which gave "chisel" fractures at 300°and 373°K. The activation energy for yielding was approximately one- half an electron; volt at all orientations, and the volume of activation was (12 to 14)b3, except near the [1101, where it was 7b3. Activation volumes generally increased after yielding. The most common theoretical models for yielding and strain hardening of bcc metals were. found to be insufficient to the intepretation of the observations here in. An explanation is proposed, based on the dislocation reaction dislocation networks and jogs, md jogs formed during plus tic flow. PRECLSE knowledge of the Drocesses involved in the yielding and plastic flow of the refractory metals is essential to the formulation of models for their flow and fracture. Despite this need, the single -crystal investigations, especially of tungsten, have been sparse. Slip occurs at low temperature, according to schadler,i in <111> directions on {110) planes; as the temperature rises to room tempera-

Jan 1, 1962

By R. L. Tobie, H. W. Seaney

Over the years since 1956 when initial experiments were conducted on underground concreting in an attempt to cope with the ground weight and pressure encountered in the development of a large-scale underground block caving system, the use of monolithic concrete linings has grown to include most of the primary development in the mining area. Although the development cost of concrete linings is higher than either timber or steel-supported openings, the repair and maintenance costs are substantially lower, making concrete the most economical means of ground support. Other ad- vantages are also apparent, in that concrete provides superior fireproofing, better ventilation, and a safer, cleaner working place.

Jan 11, 1965

By R. M. Schuller, J. J. Suloway, W. F. Childers, R. A. Griffin, S. J. Russell

Seven solid wastes from coal conversion processes were characterized chemically and mineralogically. The wastes included three Lurgi gasification ashes, two liquefaction residues (SRC and H-coal), a fly ash, and a water-quenched slag. Leachates generated from the solid wastes at various pH levels over the range 2.5 to 11.0 were analyzed for over 40 constituents. Results of the leachate analyses demonstrate the wide variation in constituent solubility for the solid wastes. To help assess the environmental impact of the disposal of these wastes, the leachates were also employed in soil attenuation studies and acute 96-hr static bioassays using young fathead minnows.

Jan 1, 1981

By J. M. Avasthi

The DOE-funded (Contract No. DE-ACO3-77ET13108) Gulf Research & Development Co. (GR&DC) field tests of underground coal gasification in steeply dipping beds (UCG/SDB) were conducted in the North Knobs area, located 12.8 km (8 miles) west of Rawlins, WY. The site has a gently rolling, sparsely vegetated, semidesert terrain on the transition zone between a broad, flat basin (Great Divide Basin) to the west and the subdued mountains of the Rawlins uplift to the east. A comprehensive geotechnical program (Ahner et al., 1980) was essential to successfully complete the test program. Emphasis of the program was the subsurface characterization of the site and consisted of mapping, drilling and logging, core analyses, and hydrologic tests. The samples of lithologic units over- and underlying the G coal seam were tested in the laboratory for their modulus and strength. This program provided the required data necessary for designing surface facilities, input for permits, and ensuring correct placement of the process modules. The two UCG tests at the Rawlins site were conducted in the nominally 6.7 m (22 ft) thick G coal seam (rank-subbituminous B), dipping at 63°.

Jan 1, 1984

By Carl Zapffe

The manganese ore reserves of Lake Superior, because of their location and nature, have recently achieved a rnarked degree of importance as compared with the world&apos;s manganese reserves. To appreciate fully the significance and the adequacy of this reserve, one should understand how such ores are used, where obtainable, the quantity used, possible avenues for increasing use or application, and the chemical and physical characteristics of the available ores. Only with those data at hand, is it possible to arrive at a convincing answer to the question whether the reserves of manganiferous iron ores are adequate to satisfy the annual demand of the presently known iron ores for the full life of the latter. That they should last is vital; and to ascertain whether they will last was the purpose of the present investigation, which marks the first attempt to study these Lake Superior reserves. The Lake Superior region possesses and supplies the full assortment of iron ores needed for the conversion of ore into pig iron and steel ingots and castings. These ores are named bessemer, low-phosphorus and high-phosphorus non-bessemer, manganiferous and siliceous; and to include the term aluminiferous would be in keeping with the most recent nomenclature adopted by some dealers. About 35 or 40 years ago, perhaps less, most of the Lake Superior ore which is being used today was the material then considered either useless or too poor for immediate use; perhaps it was considered no more than a future reserve. An examination of the analyses of ores and the guarantees in the sales of those older times convince one that the opinions of those days must have been governed by only small differences in analyses. Some grades of ores used today in substantial amounts were used most sparingly only one or two decades ago. The relative quantities of the different ores used are ever changing; and, bit by bit, the metallurgy and the opinions are ever changing and the prejudices against certain ores and practices decrease. This is unquestionably more pronounced for the manganiferous ores than for any other kind. If, when using the present data for manganiferous ores, we will only be content to make allowances for the same experiences other kinds of ores

Jan 1, 1927

By R. P. King

The two-phase distributed-parameter kinetic model for flotation has been wed as the basis for a digital simulation of flotation plants of arbitrary configuration. Ores that contain any number of minerals can be handled. The effects of incomplete liberation and particle-size distribution are specifically allowed for. The simulator allows the investigation of variations in throughput and in the slurry density of the feed, and of variations in stage volumes and aeration rates. It can handle cell behavior even under conditions of hindered flotation. The requirements for data preparation are completely documented so that the computer program is suitable for general-purpose use. The program is written in Fortran. The output from the simulator consists of the complete material flows in the plant, as well as the grade, recovery, and particle-size distribution in each stream.

Jan 1, 1976

By Toshihisa Adachi, Shosei Serata, Shunsuke Sakurai

The present state of knowledge of three-dimensional rock properties does not provide an adequate basis for evaluating the safety of under- ground structures in situ. Most of the triaxial studies reported in the past have dealt with crushing strength, but have failed to consider the intergranular behavior and triaxial strain state of rocks. Without this information, the structural competence of rocks cannot be accurately assessed. The absolute three-dimensional testing method (ATT) was conceived for the purpose of analyzing the three-dimensional states of stresses and strains in aggregate rocks under conditions commonly encountered in underground structures. In-situ stress-strain states are not simple, even in the simplest possible form of opening, excavated in a homogeneous and isotropic rock medium. In general, there are four basic stress-strain states which are present in underground openings, regardless of the complexity of their geological conditions. They are the yielded, brittle-fractured, stress-relieved, stress-concentrated states, as illustrated in the schematic diagram, Fig. 1. The ATT machine was designed to create and study all these states in the laboratory. A theory describing the aggregate behavior of rocks under these diversified states is essential to evaluate the safety of underground structures. The Griffith theory is limited to tensile failure of ductile materials and therefore does not apply to behavior of aggregate rocks under compression. The Griffith theory also fails to consider the grain boundary characteristics of aggregates, which is the determining factor of rock behavior. The Mohr-Coulomb theory of failure ignores the importance of the intergranular behavior of rocks. An application of the continuum theory to

Jan 1, 1972

By Y. J. Wang

A critical path approach is presented for the problem of mine ventilation networks where regulators and fans are employed to control the airflow distribution. The problem is a classic one arising in mine ventilation planning. By identifying the analogy between the network for controlled flow and that for critical path method (CPM), the applications of the well known CPM technique to the ventilation problem become straightforward. The mathematical formulation of the problem is presented and the solutions are illustrated with examples. The cutset operation is introduced and employed for obtaining alternative solutions. The effects of booster fans on the total air power of the ventilation network are also discussed.

Jan 1, 1983

For the first time in the history of shaft sinking, the concept of mid-shaft loading has been used. By making use of available hoisting capacity during drilling periods, development work on underground hoist chambers and ore-pass and ventilation by-pass systems at Vaal Reefs South gold mine is being done simultaneously with sinking. This factor, together with the unusual configuration and design of the twin-shaft system at Vaal Reefs South, and the use of raise borers in the installation of ore-pass and ventilation by-pass systems, will mean that the shaft will be commissioned at least a year earlier than would have been possible had conventional methods been used. The possibilities of mid-shaft loading in reducing the time normally taken by shaft service development were recognized by Anglo American Corp. consulting engineers and Shaft Sinkers Pty. Ltd., the company which is sinking both shafts at Vaal Reefs.

Jan 1, 1970

By John M. Logan, John Handin

Quasi-dynamic triaxial compression tests have been done for the first time at confining pressures to 7 kb. The intermediate strain-rate apparatus employs a gas loading cylinder which allows axial strain rates up to 102/sec on a sample 2 cm in diameter and 4 cm long. Samples can be deformed at confining pressures to 7 kb. Strain gages bonded to the loading piston and to the jacketed specimen allow internal measurements of load and sample strains respectively. Westerly granite has been deformed at confining pressures to 7 kb, room temperature, and axial strain rates of 10-2 to 1/sec. An increase of ultimate strength with confining pressure was found as expected. The ultimate strength was also found to vary directly with increasing strain rate; the rate of rise increases with confining pressure. Brittle deformation has dominated the sample behavior. Solenhofen limestone has been deformed at confining pressures to 3 kb, room temperature, and axial strain rates of 10- to 10/sec. The brittle-ductile transition was found to take place at about 1.5 kb confining pressure at a strain rate of 10/sec.

Jan 1, 1971

By D. A. Dukelow

By using the U. S. Steel oxygen sensor to measure the oxygen content of the steel, deoxidation practices have been developed for silicon-killed fine-grain steel produced by the basic oxygen process. Measurements of oxygen content taken at final turndown are related to the amount of the aluminum addition to the ladle necessary to obtain the desired aluminum analysis for proper grain refinement. In comparison with heats deoxidized by the standard approach, which is based on carbon content, the heats deoxidized according to the oxygen-sensor-based schedule showed a 25 percent decrease in variability from the desired aluminum content. As more heats of a particular grade are made, it is expected that improved quality will result in decreased rejections and better analysis control. Sensor-based deoxidation schedules are also being developed for semikilled, rimmed, and capped steels.

Jan 1, 1972

By T. C. Wilson, Gerald Edmunds, W. M. Peirce, E. A. Anderson

Thirty-six elements have been alloyed singly with cartridge brass. Ammonia and mercury stress-cracking tests have been conducted on the as-rolled and recrystallized strip. Ultra high purity cartridge brass has also been tested. Silicon improves stress- cracking behavior. High silicon (I per cent) cartridge brass quenched from high temperature (for example, 800 C.) annealing is exceptionally resistant to ammonia stress cracking. This improvement is not lost by subsequent cold working, but is greatly reduced by subsequent low temperature annealing. Phosphorus, arsenic, barium, cerium, magnesium, tellurium, tin, beryllium, and manganese benefit stress-corrosion resistance under some circumstances, but not others. The other alloying additions tried had no large effect on stress-cracking resistance. None of the elements added accelerated stress cracking. The impurities in commercial brass are not responsible for season cracking.

Jan 1, 1945

By A. C. Fieldner

ASH in coal has always been regarded as an undesirable substance, as the heat content of a coal decreases in direct proportion to its ash content. It represents so much inert material that has to be transported, handled when the coal is burned, and finally disposed of. W. R. Roberts, in an address before the Engineers&apos; Society of Western Pennsylvania, Pittsburgh, on Sept. 29, 1925, said that on an annual output of five hundred million tons of coal, a reduction of 3 per cent. of ash means fifteen million tons of refuse and a decrease of $30,000,000 in freight charges. Ash also often prevents efficient utilization of the coal through the formation of clinker caused by the melting of the ash constituents when subjected to heat. The mineral constituents of coal may be of such nature as to make the coal unsuited for specific uses, as for instance, high-sulfur coal for making metallurgical coke. While the usual proximate analysis of coal gives the amount of ash, it gives no information as to the nature and composition of the ash nor of the mineral constituents from which the ash is produced. For the efficient washing of coal to remove ash-forming constituents it is desirable to know the composition and distribution of the ash-forming constituents. Obviously such information is also desirable for the most efficient utilization of coal.

Jan 1, 1926

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1918

By Donald V. Fites

In the face of an increasing demand for minerals, the resulting technological developments, and rising overburden-to-ore ratios, many open-pit mines now incorporate totally different concepts for the removal of ore and overburden. Moreover, under a growing number of these concepts, wheel tractor scrapers are being assigned a major role in material- handling systems for unconsolidated overburden removal. To say that scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. According to the Minerals Yearbook, about one half of the material moved in metal and nonmetal mines is never drilled, blasted or broken by other means. Scrapers Find Wider Application The increased use of scrapers in open-pit mining today is due in part to improved design which has endowed these units with added versatility and in- creased their production capability. The modern scraper, which is designed as a loading and hauling vehicle, cannot be compared to the original tractor- drawn scrapers which were limited in capacity, maneuverability, and speed. Improved design of the scraper bowl ejection system has aided production. Gravity ejection has been replaced with positive, forced ejection of material by hydraulic or mechanical action. Bowl and cutting-edge design which allows for maximum load with minimum effort has also increased production. An example of this was the introduction some years ago of the low-silhouette scraper bowl which reduced the work required to lift the material.

Jan 5, 1969

By Charles A. Ashburner

&apos; I. Natural-Gas Explorations. The rapid development of the natural-gas* industry in Western Pennsylvania, and the great economy which results from its use, both for manufacturing and domestic purposes, has led to an inquiry as to the occurrence of this gaseous mineral in all thickly populated and large manufacturing centers of the United States. Natural-gas springs are to be found in almost every State in the Union, and in many States gas has been obtained in wells sunk either for water, oil, or gas, or in search of solid mineral deposits. The occurrence of natural gas is, however, not dependent upon mere chance, as is popularly supposed, but upon the existence of special geological phenomena; this fact is now recognized by professional men and by many practical men concerned either in the exploration for or in the use of this gas. The desire among our leading manufacturers, to emulate Pittsburgh, has led to the sinking of many wells in many localities, in search of natural gas. Some of these wells are now being located and drilled under the direction of professional experts, but many more have been, and are still being located by "quack " explorers, who often depend upon spiritualistic communications, or the diviningrod, or by intelligent persons, who are ignorant, however, of the geological and physical conditions under which gas has already been found. My attention has recently been directed to a number of these exploring operations where holes have been drilled, and, after failing

Jan 1, 1887

Jan 1, 1961

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.&apos; EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By T. B. Gyles

Zinc is made by the National Smelting Co. and its associates by both the horizontal retort process and the vertical retort process developed by the New Jersey Zinc Co. This paper deals only with the horizontal retort practice at Avonmouth. That the horizontal retort process does survive in all countries in some form or other is due to at least partial success in overcoming some of the inherent difficulties of the process. The horizontal retort furnaces ran into considerable difficulties when the product of the selective flotation of mixed lead and zinc ores became the normal material for treatment. It is necessary, therefore, to make some reference in connection with the process to the preliminary treatment of the ore prior to distillation.. Therefore we include some small reference to this aspect in our description. Furnace Design and Structure Of the types of furnaces in operation at the company&apos;s various works, those at Avonmouth are perhaps more typical of the trend to utilize large units, with a subsequent saving in costs, such as heating and supervision.

Jan 1, 1937

Jan 1, 1970