Search Documents

By J. M. Camp

In conforniity with the design of the oficials of the United States Steel Corporation for the standardization of the methods employed in the sampling and analysis of all materials encountered in their various lines of manufacture, the Chemists' Committee presents this compilatioti of standard methods for the sampling and subsequent analysis of molten pig-iron. In selecting the methods, the Committee employed the same line of procedure as in former cases, viz., the careful consideration of all the methods employed in each laboratory of the Corporation, evolving therefrom the several methods herein described, the immediate adoption of which is desired. The services of Messrs. W. B. N. Hawk, William Brady, and C. H. Rich, a sub-committee appointed for the preparation of the present paper, are gratefully acknowledged. II. Introduction. A quite obvious cause of nonconformity of results of comparative analyses in the various laboratories of the Corporation has been an apparent lack of uniformity of method in the sampling and analysis of molten iron. This condition is particularly apparent with regard to the determination of the sulphur, numerous discrepancies in which would appear t.o indicate the absence of, and the necessity for, some uniform method of procedure. The estimation of the

Jan 1, 1913

By Henry F. Hebley

INTRODUCTION How often has the thoughtful observer pondered the apparent contradictions experienced in the weather? One can take records of two days, one in the winter and one in the summer. The "degree days" indicate that space heating and domestic load were present in one case and not in the other. The Business Index may be about the same, indicating that the industrial activity of the area and its concomitant use of fuel were about the same. Thus the volume of the products of combustion released to the atmosphere varied only as related to the space heating demand. Yet on one day in winter the atmosphere may be clear and bracing, while on a summer's day the air is thick and murky and the visibility sharply reduced. The situation may be reversed. What are some of the factors that contribute to the creation of these conditions? These few notes have been prepared to indicate some of the influences that are exerted on the problem. THE SOURCES OF ATMOSPHERIC POLLUTION The industrial area of Pittsburgh, Pa., has been a dominant center for the production of iron and steel for over one hundred years. In fact, with the growth of the numerous auxiliary processes Allegheny County which contains Pittsburgh is probably the most industrialized county in the world. In addition, the type of manufacture carried out in this area is predominant dependent on thermal energy (heat). That energy is supplied from coke and coal produced in the vicinity of Pittsburgh. Indicative of the stupendous quantities of fuel that are employed in this industrial area's economy, the following (Table No. taken from the U. S. Census (1940) may I of interest. An influence that has never been fully appreciated by many individuals is the fact that no matter what adventures the gases of combustion experience as they pass through the various processes, ulti¬mately the spent gases are discharged through chimneys to the atmosphere.

Jan 1, 1948

By Karl Fetters

IN the process of making steel in the open-hearth furnace the refining of the metal during the working period of the heat is largely accomplished through the agency of the slag. From the birth of the process until the present day steelmakers have recognized the importance of the slag in determining the composition of the metal and the quality of the product. The general relationships between slag composition and metal analysis have long been known, at least in a qualitative or approximate fashion. For examples, the iron oxide content of the slag is higher on lower carbon heats; the more basic slags are higher in iron oxide for a given carbon content; certain amounts of iron oxide and lime are required for phos-phorus removal and a high lime-silica ratio is needed if the sulphur content of the metal is to be diminished. In recent years a number of quantita-tive relationships involving these and other variables have been developed through plant and laboratory studies by numerous investigators in this country and abroad. The direct comparison of laboratory and open-hearth data involves the question of the degree to which each approaches the conditions of chemical equilibrium, a question which, from the open-hearth standpoint, we are scarcely yet in position to answer. And, although a considerable body of dependable equilibrium data has been obtained in the laboratory, this work has not yet been extended to cover the ranges of slag composi-tion encountered in basic open-hearth practice. In the present study we shall not attempt to draw comparisons between data from the two sources; nor do we attempt to draw conclusions as to the approach to chemical equilibrium in the open-hearth furnace. Many of the operating variables that are likely to be erratic or unrecorded during the earlier stages of the heat become more consistent and are more readily subject to observation and control during later stages. For example, undigested lime or ore gradually goes into solution, the rate of carbon drop levels off, and the temperature of the metal is brought under control. For these and other reasons a greater degree of self-consistency is likely to be found among data obtained during the

Jan 1, 1940

By Rudolph Emmel

The mines operated by the South American Development Co. are located in the Zaruma mining district of southwestern Ecuador. They are near the old mining town of Zaruma, which is the only important city in the canton of the same name. The district is situated in the upper end of a valley lying between two spurs of the Cordillera, one of which may be considered the Coast Range and the other an intermediate range. The mining camp proper, known as Portovelo, and the plant are 2.4 km. south of Zaruma, on the north bank of the Amarillo River, a tributary of the Tumbes River, which flows southwestward through Peru to the Pacific. Portovelo is difficult of access; it is reached from Guayaquil by means of river steamers and muleback. 'Embarking at Guayaquil, the route is down the Guayas River, across the Jambeli Canal, and up the Santa Rosa River to Santa Rosa, a distance of 177 km. From Santa Rosa, the road or trail follows the Santa Rosa River, then across the summit of the Coast Range into Portovelo, a distance of 74 km.—a two-day trip on muleback. The mining property of the South American Development Co. comprises 297 lode claims and 142 placer claims. The combined lode claims cover an area, roughly rectangular in shape, 9000 m. long from north to south by 4000 m. wide; the northern edge of the rectangle is about 3000 m. north of the central plaza of Zaruma. Mineral lands in Ecuador are held by virtue of an annual tax per claim paid to the central government, no surface rights being included. HiSTOry The Zaruma mine has been worked by white men since 1549, probably before that it was worked by Indians. The followers of Pizarro, led by traces of gold in the sands of the Tumbes River, followed that stream to its source, worked the gold veins that they found and established the city of Zaruma. Among the mines worked by them were th Sesmo, Leonora, Viscaya, and Mina Grande. Only the soft ores at the outcrop were

Jan 1, 1925

By John M. Crowl, L. E. Sawyer

5.3-1. General Public Resistance to Strip Mining. Surface (strip) mining is the oldest recorded method of extracting coal and other minerals from the earth. This method of mining completely alters the topography of the earth's surface, leaving an area of more or less parallel ridges or of peaked mounds of the materials which overlay the mineral seam. It destroys all original vegetation and provides materials for new type soil. During the early years the acreage mined by this method was small, land was plentiful, and with a growing young nation no thought was given to the restoration of the disturbed areas to some form of productive use. Early in the present century the development of steam shovels and drag-lines made it possible to remove thicker overburden to recover the products. With the deeper digging, the size of the disturbed areas increased. With this increase in the size of equipment and the improvement of blasting techniques, mining was expanded into more prominent locations and to areas of more valuable land. The more progressive operators became aware of the need to reclaim those areas for some productive use. Electric shovels with capacities of up to 200 cu yd and draglines with capacities of 145 cu yd, capable of uncovering products over 100 ft below the surface, are now in use. Combined with the increase in the size of equipment, the expansion of contour mining or rim stripping in the mountainous areas has focused public attention on the need for a sound reclamation program for all disturbed areas. APPEARANCE. After mining, the areas consist of varying percentages of rock, shale, slate, and soil material devoid of all plant and animal life. Unless a definite reclamation plan is carried out, many of the mined areas will remain bare for a period of years. The topography of the area is completely altered. What may have been level to rolling land in cultivation, in grass, or in timber is thrown up into a series of ridges or mounds.

Jan 1, 1968

By D. O. Hobson

Zirconium single crystals of various specific orientations were fabricated by rolling or drawing. The resulting textures were determined and are discussed with respect to the deformation modes that produced them. The crystals deformed in a predictable manner by combinations of up to third-order twinning with three twinning modes and by slip. Twinning was found to play a major role in initial texture formation. Texture changes produced by slip occurred only at the higher reductions. The twinning sequences that produced each intensity peak during the initial reductions could be identified. Schmid factor criteria were found useful in predicting which deformation modes to expect for each crystal orientation and fabrication procedure. The possible application of these data to poly-crystalline material is discussed. PREFERRED orientation or texture has a significant effect on the properties of most materials, causing anisotropy in fabricated cubic metals and enhancing the natural anisotropy of noncubic metals. This study evaluates the effects of several fabrication methods on the textures formed from specific starting orientations of zirconium single crystals and, it is hoped, gives an insight into the effects of the same operations on poly-crystalline material. BACKGROUND In fcc and bcc metals, texture changes take place by gradual lattice rotations caused by the operation of one or more slip systems. Deformation twinning plays an insignificant role in the deformation of such metals. In zirconium and its alloys, however, and in many other hep metals the ability to twin allows very rapid texture changes to be made with very small amounts of deformation. The deformation systems found in zirconium and its alloys are prism slip and three twinning modes.1 Slip occurs on the {1010}< 1120) system. There is little or no appreciable basal slip in zirconium. The twinning planes, illustrated in Fig. 1, are {1012}, {ll2l}, and {1122}. Two twinning modes, the {1012} and the {ll2l} operate for a tensile stress along the basal pole. A compressive stress parallel to the basal pole is required for {ll22} twinning. These twinning operations cause a 35- to 85-deg reorientation of the basal pole. The {1012} twin is the predominant tensile twin at room temperature. The twinning shears, S, are shown in the figure. A criterion for predicting which deformation system will operate when a grain is subjected to a known stress state is the Schmid (orientation) factor. This factor gives the fraction of the applied stress that computer program was written2 to calculate the Schmid factors for the four deformation modes in zirconium. It assumed three orthogonal stress axes and considered ninety-one different orientations of the basal pole in one octant of this stress space. At each basal pole position the Schmid factors were calculated for seven positions of rotation at 10-deg increments of the unit cell about the basal pole. Schmid factors were determined for a total of 637 orientations and for twenty-four deformation systems in each orientation. The program listed the Schmid factors for uniaxial stress parallel to each axis and, to approximate rolling, or-thonormal biaxial stress was also considered. Fig. 2 shows the range of orientations over which the various types of deformation would tend to predominate in biaxial plane strain with the stresses, equal magnitude. The exact boundary position between regions of different deformation modes depends, however, on the relative values of the critical shear stress for each deformation mode. Fig. 2 is drawn on the assumption that they are equal and it therefore may be only approximately correct. It is also recognized that the biaxial stress analysis may not be applicable in certain crystal orientations. EXPERIMENTAL PROCEDURE Single crystals of zone-refined zirconium, produced by Wilson of this Laboratory,3 were electrical-discharge-machined to form specimens for rolling, tube-drawing, and rod-drawing studies. Specimens were rolled at room temperature on 2-|--in.-diam hand-powered rolls from three different starting orientations: 1) the basal plane parallel to the rolling plane and the [1120] in the rolling direction, (0001)[ll20]; 2) the (1120) plane parallel to the rolling plane and the basal pole in the rolling direction, (1120)[0001]; and 3)_the (1120) plane parallel to the rolling plane and the [1100] in the rolling direction, (1120)[ll00]. Drawing specimens were cut with the [0001] direction as the drawing direction in the tube blank and [1120] as the drawing direction in the rod specimen. The drawing

Jan 1, 1969

By E. H. Greener, M. E. Fine

The internal friction (1/Q) of cobalt Fig. 1 (measured by an electrostatic dynamic method1) near 250°C begins to increase rapidly on heating and continues to increase until 560°C, the highest tem- perature measured. In the plot of log of 1/Q against 1/T, above 250°C the data nearly fit two straight lines intersecting at 400°C, approximately the temperature of the hexagonal-cubic transformation. The higher temperature branch corresponds to an effective activation energy of 6500 cal per mole, the lower temperature branch 11,000 cal per mole. Young&apos;s modulus Fig. 2 increases approximately

Jan 1, 1959

By N. F. Neumann, A. W. Schlechten

Metal chlorides were formed by reacting metal oxides and calcium chloride; the effect of additions to the reaction mixture was studied. It was found that by use of proper additions, metal chlorides could be prepared from mixtures that were not reactive under ordinary conditions. ManY recent metallurgical developments involve the use of chlorine or chlorides as primary reagents; good examples are found in the production of ductile zirconium and titanium by reduction of their chlorides with magnesium. Various methods of preparing metal chlorides are used and many others have been proposed. Some chlorides are formed by the direct combination of a metal or alloy with chlorine. Other processes react chlorine and metallic oxides; carbon or other reducing agents are usually employed to reduce the metal oxides and so promote chlorination. Metallic chlorides have also been produced by the exchange of chlorine between metal oxides and a chloride, such as sodium chloride. This type of reaction was the basis for the old process of chloride roasting in which metal ores were roasted in the presence of salt. Soluble chlorides thus formed

Jan 1, 1959

Expect Labrador Iron Ore Shipments by 1954 Iron ore shipments from the Quebec-Labrador area are a "definite expectation" by late summer, 1954, according to William H. Durrell, general manager of the Iron Ore Company of Canada. About $120 million have been invested in the project, with a total of $200 million expected to be reached before a ton of ore is shipped, Mr. Durrell said. According to the general manager approximately 418 million tons of open pit highgrade ore have been proven in the project. Deposits lie several hundred miles north of the mouth of the St. Lawrence River in territory which was without transportation of any kind. Construction of a railroad from Seven Islands to Knob Lake, about 360 miles, is an important part of the development plan. The railroad will be the first to adopt complete roller bearing applications. Construction is on schedule with 215 miles of the route graded. Completion involves two tunnels through rock, one of almost half mile length, a 700-ft bridge and several smaller spans.

Jan 3, 1953

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By Robert I. Kingman

SUFFICIENT testing has been performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.l The present flowsheet for the recovery of ilmenite consists in grinding the crushing plant product in four open-end rod mills in closed circuit with mechanically vibrating screens to approximately -20 mesh. The screen undersize is treated in Crockett magnetic separators which produce three products: magnetic concentrate, nonmagnetic tailing containing ilmenite and gangue, and a Crockett slime overflow. The non- magnetic tailing is classified into eight sizer spigots products and a classifier overflow. The spigot sand products are tabled separately to produce a rough ilmenite concentrate, a middling product and a tailing. The table middlings are returned to Crockett feed. The table concentrate is dewatered and dried and further concentrated on Wetherill magnetic separators to produce the finished ilmenite concentrate.

Jan 8, 1950

By P. G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the necessary information in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included: - careful checks on the sampling and assaying, - selection of representative samples used to establish the recoverable amounts of precious metals in the ore, - examination of underground workings driven to provide samples both for metallurgical testing and for assay comparison, - evaluation of plant site and waste dump areas as non-material, including a placer examination of the tailings disposal area, and location of an adequate water supply. All these investigation were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1985

By Francis A. Pocock

The writer is continually asked, if this electricity:is all you claim for it, why do not the mines put it in and use it? The best answer was given by Mr. John Fox Tallis, in his paper read before the South Wales Institute of Engineers in 1888, namely, that the reasons are similar to those which have prevented the more general employment of other systems of haulage. Managers, as a rule, are " not experienced mechanical engineers; neither are they all versed in electrical engineering." It may be said that there are a number of " able and practical electrical engineers who could do the work; but those electrical engineers are not conversant with the practical routine of colliery work and are, therefore, placed at a disadvantage by not knowing the actual requirements of mining engineers, and the many little difficulties to be met and contended with in underground workings; and, until mining engineers have acquired the necessary knowledge and a confidence in electricity, it is only natural that they will continue to follow the beaten path." In the above remarks, Mr. Tallis has hit the nail on the head. In the face of the partial failure, financially, of the haulage-plant which the Union Electric Company of Philadelphia had set to work at Lykens Valley, Pa., an electric haulage-plant was installed near Scranton, Pa. The question was not whether electricity could do the work, but whether any electrical company knew enough about the practical difficulties to attack and overcome them. That point being settled, the remainder was easy. The contract for the Erie Colliery haulage-plant was signed in January, 1889. This colliery is owned by the Hillside Coal and Iron Company, Mr. Samuel Hines, President, and Captain W. A. May, Superintendent. The company has been using arc-lamps in its breakers for three years. It is the only company in the Lackawanna Valley which has had enterprise enough to do so. Consequently, it was acquainted

Jan 1, 1890

By C. K. Leith

ManGanese is one of the minerals which is principally consumed in countries other than origin. Nearly 85 per cent. of the world&apos;s production is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent. of the world production comes from Brazil, Russia, India, the Gold Coast of Africa and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this inovement is for considerable distances and is occan bornc. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metallurgical methods, only 35 per cent. of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explorations now under way, indicate no shortage from a world standpoint for many deeades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel industry uses over 90 per cent. of all the manganese mined and is acquiring control of a considerable part of the production in all of the principal fields—the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies arc of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing uneasiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few cnough to warrant the belief that more or less monopolistic elements of control arc not impossible.

Jan 1, 1927

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse&apos;s conclusions, Barrett&apos;s results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers&apos; results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,&apos; Si." —large a solubility: Al.9

Jan 1, 1954

By E. S. Burnett, R. V. Higgins, H. C. Miller

Information obtained from subsurface pressure and ,temperature measurements in oil wells now is recognized as invaluable to geologists, engineers, and operators of oil properties. Available only during the past few years, data resulting from subsurface-pressure surveys in oil wells already have found widespread application in the estimation of reserves and in the planning of comprehensive oil-field development programs. Subsurface pressure and temperature data, together with measurements of fluid volumes produced by individual wells and specific gravities of the fluids, also are included in the fundamental information essential in studying the movement of oil, gas and water through reservoir sands to wells. Heretofore, laboratory findings were relied upon almost entirely for information pertaining to the mechanics of flow of fluids through porous media, because there was no way to check laboratory results with actual performance in underground formations until subsurface pressure and temperature instruments were developed. Laboratory and field experiments now lend themselves to closer correlation—a fact that will accelerate the interpretation of many phenomena that occur when oil and gas flow through reservoir rocks, thousands of feet below the surface of the earth. This paper summarizes the results obtained thus far in a Bureau of Mines study of certain data pertaining to subsurface pressures and production of wells producing oil and gas (and water). For wells that have been studied, flowing naturally under volumetric or hydraulic control, a simple relation has been found between the mass rate of fluid (oil, gas and water) production and the corresponding drop in pressure in the reservoir sand. The equated relation embodies a productivity factor or "index" expressed in terms of mass rate of fluid production per pound drop in pressure through the sands. The equation as developed is an expression of the ability of a well to produce, which permits comparison on a uniform basis of the productivities of different wells. The study shows also that over the range of observed data a productivity factor

Jan 1, 1937

By M. Schussler, J. S. Brunhouse

Arc-melted and electron-beam melted tantalum in the cold-worked and the recrystallized conditions showed high strength, good tensile ductility, and excellent notch toughness down to 321°F. Arc-melted material, containing moderate amounts of interstitials, possessed better short-time strength than higher purity electron-beam melted material up to 2000°F. Cold-working substantially strengthened arc-melted tantalum, whereas electron-beam melted material exhibited a low work-hardening rate and possessed better formability characteristics. With identical compositions and microstructures, the mechanical properties of melted tantalum and uacuum-sintered tantalum should be similar. TANTALUM metal usage is increasing rapidly in a number of applications. The outstanding chemical corrosion resistance of tantalum accounts for its applications in chemical processing equipment for severe service conditions and for surgical uses in the medical field. The largest present requirements for tantalum are in the electronics industry, where its special properties are useful in capacitors. The high melting point (5425°F) and inherent ductility of tantalum also suggest that tantalum and tantalum-base alloys might offer an excellent combination of high strength at very high temperatures and good fabri-cability. Pure tantalum has been used in significant amounts in parts requiring high-temperature strength, such as heating elements, reflectors, and heat shields in high-vacuum high-temperature furnaces and in electronic tubes. A few very promising tantalum-base alloys have been developed and are being investigated extensively. The possibilities for tantalum as a high-temperature structural material, either unalloyed or alloyed, will become better defined when more extensive mechanical property data are known. pughl measured the tensile properties of vacuum-sintered tantalum in sheet form for the temperature range of 78" to 1500°K (-321&apos; to 2240°F), and Bechtold reported data obtained at low temperatures.&apos; Drennen3 determined creep and stress-rupture properties of both vacuum-sintered and arc-melted tantalum sheet at 1200 °F. Some additional data on the mechanical properties of tantalum at temperatures up to 5000 °F have been summarized elsewhere.4&apos;5 It is probable that large structural shapes of tantalum, either unalloyed or alloyed, can most readily be produced from ingots prepared by melting. Consequently, the present investigation was undertaken to determine more extensive short-time mechanical properties of tantalum metal consolidated by melting. EXPERIMENTAL PROCEDURE Melting and Fabrication—Two tantalum ingots were utilized in this study to obtain information on the effect of interstitial elements on mechanical properties. Both ingots were melted from Union Carbide Metals Co. tantalum dendrites.

Jan 1, 1961

By Horace Tharp Mann

Jan 1, 1926