Search Documents

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Rudolf Hubmer

In October 2013 JSW Steel decided to place an order to Primetals Technologies Austria (former Siemens VAI Metals Technologies) for the installation of a comprehensive Level 2 process optimization system for more than 20 existing production facilities of various suppliers. For SMS-I new L2 systems are provided for two hot metal pretreatment stations, three hot metal desulphurization stations, three ladle furnaces, two 1-strand slab casters, a ladle tracking system as well as a shop supervisory system. Additionally the existing L2 system for one 1-strand slab caster is being upgraded in the course of the project. In SMS-II new L2 systems for the 7 hot metal desulphurization stations, 4 ladle furnaces, 1 new RH vacuum degasser, ladle tracking system and a shop supervisory system are supplied. Despite of the challenging time schedule the commissioning of the single facilities started within less than 12 month after contract effectiveness. The installed Level 2 process optimization systems together with the achieved results are described in this paper.

Aug 16, 2017

By Rodrigo Perito Cardoso

Low-temperature nitriding of stainless steels is applied to obtain wear resistant surfaces without losing its corrosion resistance. The treatment consists in introducing nitrogen into the steel surface avoiding chromium nitride precipitation. The corrosion resistance of martensitic stainless steels is expected to be improved if the treatment parameters are correctly selected. It can be related to ?Fe2-3N and a'N phase formation on the treated surface. In the present work the influence of the pretreatment and treatment temperature on corrosion resistance of plasma nitrided AISI 420 steel samples is studied. Annealed, as-quenched and 400ºC-tempered samples were nitrided at 300, 350, 400, 450 and 500°C, for 6 h at 600 V. The pressure was 3 Torr and the gas mixture was composed of 70%N2, 20%H2 and 10%Ar, at a gas flow rate of 3.34×106 Nm3s-1. Plasma was generated using a square-wave pulsed DC power supply and the sample temperature was controlled by the duty cycle. The modified layers were characterized by optical microscopy, X-ray diffraction and microhardness measurement. The corrosion resistance was studied by electrochemical characterization, by means of Open circuit potential and Anodic polarization curves. The maximum surface hardness was achieved at 400°C. This temperature seems to be near the limit temperature for low-temperature treatment aiming to improve or at least to keep unaltered the corrosion resistance in relation to that verified for non-treated steel samples. Results confirm that the pretreatment and treatment temperature significantly affects the corrosion resistance of the treated surface.

Aug 8, 2018

By Mühlböck Marlene

Increasingly stringent global environmental regulations are forcing steel producers to continually improve the efficiency of sinter waste gas treatment. With the Selective Waste Gas Recirculation (SWGR) system from Primetals Technologies, lower production costs can be achieved and the size of downstream waste gas cleaning units can be reduced for investment savings. SWGR features the extraction and reuse of hot sinter off gas from selected wind boxes along the sinter strand, which contributes to improved energy efficiency and off gas treatment in the sintering process. With the next generation of SWGR, Primetals Technologies can provide an energy optimized, emission optimized and environmentally friendly solution that meet customer requirements and country specific regulations. This paper demonstrates the latest developments in selective waste gas recirculation, especially results from pot grate tests and comparison from lab to real plant data. Furthermore theoretical finding and mathematical modelling is presented.

Aug 16, 2017

By Gilberto Álvares da Silva

New elements have been inserted in NiTi lately, resulting in ternary alloys with specific characteristics beyond Shape Memory Effect and Superelasticity. Among all others alloying elements, the Ag additions itself gives potential antibacterial activity to that smart material. So on, the elaboration procedures of ternary NiTiAg alloys was studied in order to obtain a melting procedure to ensure further studies on this alloy. Microstructural and thermal analyses were used to evaluate the VAR-remelting production of NiTiAg with 4.0% wt silver content. The microstructure is composed by a NiTi matrix, pure Ag precipitates, and, scarcely, TiC inclusions. Heat treatments at high temperature could not dilute those Ag particles, but could lead to the precipitation of new ones. The silver element reduces the temperature of the martensitic transformation, yielding a material with superelastic behavior, beyond induces the R-phase on cooling stage of this alloy.

Aug 8, 2018

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Dilermando Nagle Travessa

High strength-light weight materials are very attractive for the transportation sector, particularly to the aerospace industry. High strength-age hardenable aluminium alloys are widely used in airframes due to their unique combination of strength, density, toughness, corrosion resistance, cost and easy processing. However, the hardening capacity of such alloys is somehow saturated due to thermodynamic issues related to the conventional processing. The production of aluminum-matrix composites is a promising strategy to overcome this limitation, resulting in strength levels that cannot be reached by actual commercial aluminum alloys. In the present work, multiwall carbon nanotubes were used to reinforce the AA6061 aluminium alloy. 1 and 2% weight percent of MWCNT were mixed to the alloy powder by high-energy ball-milling process. The blended powder was consolidated by hot extrusion. The obtained composite bars were submitted to heat treatment for the T6 condition in order to combine both CNT dispersion and precipitation hardening effects. Optical and scanning electron microscopy, as well as hardeness testing, was used to characterize the bars. Typical wrought microstructure, free of defects, was observed on the extruded bars. Hardness of the composites was observed to increase by 20, 28 and 68% for 1% MWCNT 6 h milling, 2% MWCNT 6 h milling and 2% MWCNT 10 h milling, respectively, in the as-extruded condition. The better performance for the composites blended at higher milling time was attributed to a better nanotubes dispersion. Subsequent heat treatment to the T6 condition did not result in additional hardening.

Aug 8, 2018

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Satish V. Kailas

For product sustainability “closing the cycle” is the first requirement. If the materials used in making the product is not replenished at the rate at which it is being extracted, the cycle is open and the product would not be sustainable. This includes the materials used in generating the energy used to make the product, the transportation, use and disposal. If the materials used in a product, that includes lubricants, is one that cannot be replenished, it has to be recycled for the product to be sustainable. The other basic condition for sustainability is the eco-friendliness of the product. It is argued that the present lubricants do not fall in this category. Using the example of cutting oil emulsions we have shown that it is possible to meet the conditions of sustainability in terms of both the material extraction-replenishment cycle and eco-toxicity. Cutting oil emulsions made from coconut oil and natural additives are shown to have superior cutting properties and are completely eco-friendly. It is concluded that products made using these conditions are possible and is a necessity for man to lead a sustainable life. Closing the cycle, with respect to the energy used in the cycle will make the product completely eco-friendly.

Jul 31, 2018

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Günther Staudinge

Aperam is a global player in producing of stainless, electrical and special steel qualities. The steelmaking plant in Timoteo Brasil is equipped with one AODconverter for stainless steel and one MRPL-converter for special steel production. After almost 20 years of operation Aperam decided to exchange the existing 80 t MRP-L converter by a new one including a new trunnion ring and a state of the art suspension system. Due to an optimized design the inner volume of the new converter could be increased which comes along with improved production. A special feature is a flange connection in the barrel section of the converter. This allowed to avoid any critical site welding and the time between shut down of the old and cold commissioning of the new converter could be done with 17 days only.

Aug 17, 2017

By Maurizio Massimo

Danieli developed the “3Q” suite of process control technologies to address three critical principles: delivering the highest product Quality, in the required Quantity, with Quickness of response required for today’s casting machines. Ever increasing market demands for productivity and slab quality necessitate the latest advances/improvements in equipment design, process technology, and control software for all types of slab casters, and Danieli boasts a unique experience that extends from ultra high-speed thin slab casters to extra high-thickness conventional slab casters. The “3Q” system is monitored and controlled by a unique, intelligent HMI incorporating. Touch screen technology and Operator Assistant tablets. Operator Assistant is a tablet based system that guides the operator through the plant process, so that in the event of a process change or an alarm the operator is automatically presented with the choice of possible solutions / actions. The comprehensive range of technological packages cover all aspects of caster design and automation control, from feeding of liquid steel into the tundish to the final slab leaving the caster.

Aug 17, 2017

By Ernst Lindemann

Steel suppliers are required to deliver sheets with particular qualities and with lightweight-potential to the automotive industry. New types of steel call for new production processes. SMS group has developed a new micro-mill-concept, the core of which is the belt caster. This was first built on an industrial scale and has been put into operation and developed together with Salzgitter Flachstahl GmbH. The robustness in industrial-scale operation could be verified. The full use of the belt casting technology, mainly related to energy efficiency and CO2 reduction, is realized with the micro-mill-concept. This is an in-line-process, casting and rolling in one line.

Aug 17, 2017

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018