Search Documents

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Pedro Jorge Walburga Keglevich de Buzin

Steel production process generates waste, among which is the electric arc furnace dust (EAFD). This waste has varying amounts of zinc, which is principally contained in the minerals zincite (ZnO) and franklinite (Fe2ZnO4). The presence of Zn is capable of economically motivating the recycling of this residue and facilitating the co-processing of the remaining material. The zinc content in EAFD and the presence of zincite, however, have significant influence on the application of hydrometallurgical recovery processes (economic alternatives to the Waelz process). In this study, based on the computational thermodynamic tool FactSage, theoretical considerations are made on the conditions for the formation of zinc-containing minerals found in EAFD. Through thermodynamic analysis, the best conditions for obtaining a high fraction of ZnO were analyzed, which favor the hydrometallurgical processes for EAFD treatment. A classification of dust depending on the phases present in the EAFD is suggested as a guide for the feasibility analysis for the use of a hydrometallurgical process.

Jul 30, 2018

By Peter Grawenhof

In steel mills universal joint shafts, slipper spindles and gear spindles are used to overcome the design- and process- related offset between the axis of the motors and the work rolls. At the roll side the available space for the couplings is limited by the minimum work roll diameter. This leads to extremely high loaded components of the universal couplings especially at the roll side joints. Furthermore modern steel mills continuously strive to roll larger plates and materials with increased strength. This requires drive solutions with even higher torque capacity. For these applications conventional design joints are not sufficient anymore. Even alternative solutions such as hybrid- or offset- designs fall short. Therefore the companies Voith and BUMA Engineering developed together the new GearLink drive concept in close cooperation with the Voestalpine Grobblech GmbH. A completely new combination of universal joints and gear couplings offers an up to now unique solution enabling the use of 1,35- times bigger joint with a 2,5- times higher torque capacity and a 20- times longer lifetime. The GearLink system was first time successfully taken into operation at Voestalpine Grobblech in December 2013 and is up to now working without issue.

Aug 16, 2017

By Carlos Martins de Oliveira

The trucking industry is constantly seeking improvement and cost reduction of their vehicles, studying new lighter and robust materials to meet the needs of its customers. The objective of this work is to study the application of DCPD Telene, PU. R. RIM and PP-TD 20 materials in aesthetic components of trucks: bumper, calender, upper and lower bracket and side air deflector. A multifunctional work team was created to work in such parts of IVECO trucks. The work began with an analysis of possible improvements to the current parts and followed the subsequent phases: definition of new materials, virtual modeling, new tools, and durability test in vehicles. It could then be verified that the proposed DCPD Telene, PUR. RIM and PP-TD 20 materials showed greater strength, better painting surface, and reduced weight and cost in parts.

Aug 8, 2018

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Marco Castenetto

Some of the most significant Danieli innovations in the field of long products are the: i) The EWR® system, through automatic continuous head-to-tail flash welding of billets at reheating furnace exit side, enables uninterrupted production of the mill for endless rolling of straight bars, wire rod and bar in coils. The process is particularly beneficial to wire rod and bar-in-coil mills as it enables production of “customized-size coils” (any coil weight according to specific Customer request) and with extra-high final coil weight, even starting from low-weight billets; ii) The Spooler process is based on twistfree winding of hot-rolled rebars into highly-compact/ultra-heavy coils featuring a unique cobble-free un-coiling capability. This enables high-speed feeding of the downstream cold-processing lines with hot-rolled spooled coils coming directly from the rolling mill without the need of any traditional off-line operation (such as de-coiling, stretching & re-winding). The system results highly beneficial both to bar-in-coil producers and to the downstream lines operators. The latest step forward is the combined application of these two systems that has made it possible for endless rolling of spooled bar in coils, enabling to cumulate the benefits of the two processes, particularly as far as transformation costs are concerned.

Aug 16, 2017

By Piotr Pajaczkowski

Hydro generators installed in Itaipu Binacional power plant with 824/737 MVA rated output power (50/60 Hz) belong to the largest ones in the world. Among many unique features the generators are equipped with the largest hydrodynamic thrust bearings ever built (external diameter 5200 mm, axial load equals approximately 3600 t). This paper is an attempt to propose a new thrust bearing design with the use of the state-of-the-art technologies and simulation techniques that demonstrate a reduction of friction power losses generated by the thrust bearing. This paper is divided into two parts. Within the first one the original thrust bearing design which was implemented in the generators is described. Related calculation results based on a thermo-elasto-hydrodynamic (TEHD) calculation software used by Alstom will be presented. A comparison between measurement results gathered in the 1980’s is given. In the second part a potential solution of a more beneficial bearing design is described. The proposed thrust bearing design modification is an implementation of Alstom’s PolypadTM coating. This modern polymer (PEEK) coating material has already been used by Alstom in projects around the world for many years. This coating allows pushing the operating parameters limits toward higher temperatures and lower oil film thicknesses far beyond the limits known for the conventional bearing materials.

Jul 31, 2018

By Fabiano Soares

Strand guide rolls in continuous casters are crucial components for guaranteeing an optimum process for the production of high-quality steel grades. The properties of these rolls greatly influence the quality of the slab produced. The most commonly used designs so far have been the axle roll and the solid roll. A quite new roll concept is the STEC-Roll®. It combines the advantages of the axle roll with those of the solid roll. This paper explains the development of this roll type and shows the current design. The characteristics of the STEC-Roll® are presented in greater detail and are underlined by a number of simulation results. Beside the design itself, the benefits for casting and maintenance are explained, including for example the easy assembly and dismantling or the use of the roll for dry casting. A brief examination is made of the TCO for the STEC-Roll® and an estimation is provided of the exchangeability of this roll. To conclude, an overview on the current applications is presented.

Aug 17, 2017

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Robin Schott

The blast furnace process is the most important process to produce pig iron. The necessary process energy is mainly covered by coke. But the production of coke is connected with CO2-emissions and high costs. A significant measure to reduce the coke rate and with it the CO2-emissions plus costs is pulverized coal injection (PCI) through the tuyeres into the blast furnace. A further increase to substitute coke by coal can be achieved by using the Oxycoal+ technology. This article compares and shows the cost effectiveness and the decrease of CO2-emissions with the help of simplified energy balances for the only coke operation of the blast furnace, the operation using pulverized coal injection and the operation using the Oxycoal+ technology.

Aug 17, 2017

By Bart de Graaff, Victor van Straaten, Edo Engel

The hot blast system is key ancillary plant equipment with respect to safe and stable operations during a long blast furnace campaign. Hot blast stove designs have been optimized to such an extent that in some cases, their lifetimes have surpassed the campaign lengths of the associated blast furnaces by a substantial margin, with the exception of the burner and a few critical areas. This article presents recent developments with respect to designing, building new and operating existing hot blast systems for a long lifetime and at optimized performance. These developments include fundamental improvements such as dome combustion designs as well as increasingly comprehensive packages for inspection, assessment and maintenance techniques. Examples of such techniques are burner replacement with the hot blast system at operating temperature, improved double shell approaches and TOFD measurement applications.

Oct 1, 2019

By Bernardo Siqueira

This paper presents a unique stirred milling technology, Outotec HIGmill™, a modern, flexible and energy efficient grinding solution for fine and ultra fine grinding being tested in an industrial scale level. The test was performed at an iron ore pellet producing plant in Sweden (for confidentiality reasons, it will be referred to only as “the client”) where a pilot HIGmill™ unit (HIG25) was installed parallel to a conventional regrind circuit to compare its performance to the existing ball mill. By using a continuous test run procedure and evaluating the parameters of F80, P80, mill shaft rotation speed and power drawn it was determined its grinding capabilities, operational flexibility and energy efficiency. Outotec HIGmill™ outperformed the existing ball mill in the plant proving its capabilities to grinding finer, with steeper particle size distribution (PSD) and much higher energy efficiency. The tests performed showed that, with further refining of its operation, it is capable of consistently deliver the required PSD with up to 30% higher grinding efficiency.

Aug 16, 2017

By Oliver Schulz

This paper presents the latest references of the Siemens VAI slab casting technology. Following the connect & cast philosophy Siemens VAI has developed technological packages suitable for installation in existing casters of any original supplier, as well as for complete new machines. A major demand on new machines is to adapt quickly to different market demands. This requirement for flexibility can be divided into two actual trends. Firstly into casting a broad range of steel grades, thicknesses and width on the same machine and secondly having installed slab, bloom and billet caster in one steel plant to deliver all different types of needs on the market. Depending on the condition of the existing machine the focus of modernization ranges from the substitution of single components featuring state-ofthe-art technology to complete caster revamping projects. In this paper concepts and references for short machine outages and fast caster ramp-ups at moderate investment costs are presented.

Jul 30, 2018

By Felipe Krug

A decapagem química, necessária para a remoção de óxidos e hidróxidos da superfície dos arames na galvanização contínua a fogo, emprega uma solução a base de ácido clorídrico que necessita constante monitoramento. O controle da temperatura e a concentração, são imprescindíveis para obtenção de custos competitivos, qualidade de produtos e manutenção da segurança operacional. Este trabalho realizou uma crítica, nas práticas e controles já implantados, identificando desperdícios e oportunidades e fazendo um re-alinhamento do processo alterandose parâmetros e rotinas de forma a obter o menor custo, mantidas qualidade e segurança operacional.

Aug 16, 2017

By Mery-Cecilia Gómez-Marroquín

O presente trabalho trata da formação da ferrita de zinco a partir da mistura e posterior reação solido-solido entre o óxido de zinco e óxido de ferro - Fe2O3 puros em proporções equimolares. A faixa de temperatura onde teve lugar a formação foi entre 1073 e 1373 K. Testes de redução da ferrita de zinco sintética-ZF e pós de aciaria elétrica–EAFD foram realizadas usando misturas de CO e CO2 que variaram entre 50 e 100% CO. Ambos os testes (formação e redução de ZF e EAFD) foram suportados usando técnicas de caracterização física, química, estrutural e microscópica. No caso da redução, foi observado que tanto a temperatura como a percentagem de CO, foram os fatores que, mais afetaram a redução de ferrita de zinco contida no EAFD. A máxima percentagem de redução foi 85%, para 100% CO, 1373 K e 105 min, e 52%, para 50% CO, 1373 K e 105 min. Por outro lado, atingiu o 100% para 100% CO, 1273K, em 80.75 min, 60%, para 50% CO a 1373 K durante 105 min.

Aug 16, 2017

By Alessandro Molinari

In recent times, coke oven machines are acquiring a more prominent role in the coke making process. Apart from the traditional handling of the coal and coke flow, nowadays these machines are also deeply involved in all environmental and process control aspects. Paul Wurth coke oven machines have been developed by Schalke to meet the most recent requirements in terms of emissions control, automation, instrumentation, operability and maintainability. In CSP, Ceará, the new coke making plant represents the status of the art of the technologies applied to the whole coking process; starting from the Coke Oven Batteries and the Gas Treatment Plant developed by Paul Wurth up to the Coke Machines supplied by Schalker Eisenhütte, whose technology is now part of Paul Wurth coke making products portfolio. Present paper describes the plant configuration focusing on Coke Oven Machines and the key factors which are guarantying the success of the project.

Aug 16, 2017

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By Christian Geerkens

Increasing requirements on slab quality initiates SMS group in developing products with a high sophisticated level regarding production and process. These characteristics are represented by SMS group’s HD family. HD stands for High Definition or the improvement of product quality via higher precision of the casting processes. A deep look inside into casting process is realized by the use of fiber optical equipped HD mold. High definition casting process control is assured using the HD spray and HD size. For objective, environmentally friendly and highly informative analyze of the inner quality of the cast products the new HD scan is present.

Aug 16, 2017

By Gabriel Duarte Lott

O processo de análises físicas e químicas de amostras de minério de ferro [3] é um processo crucial para avaliação do tipo de minério que está sendo extraído, beneficiado e expedido nas operações das mineradoras. Assim, aplicar novos conceitos e equipamentos altamente tecnológicos, que irão garantir resultados cada vez mais precisos e a execução das tarefas de forma cada vez mais segura, é a chave e o desejo das empresas. No laboratório da VALE S/A, em Itabira, foi realizado um estudo de caso de um sistema automatizado de preparação de amostras capaz de realizar as etapas de divisão da amostra abaixo de 1mm, pulverização, confecção de pastilha prensada e fundida, análise de perda por calcinação (PPC), limpeza de utensílios e acessórios e descarte de resíduo de minério de ferro. Nesse estudo é abordado a avaliação dos equipamentos e tecnologias instalados e os desafios tecnológicos e de processos enfrentados durante a implantação desse projeto.

Oct 30, 2017

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019