Search Documents

By E. R. Maize

[In report of Investigations 3452,5/ baling with roof movement in the Crucible mine, reference was made do to the fact tart timber decay was being studied at the time of writing. This roper, written after completion of that study, describes s the work and summarizes the data obtained. When the study of roof movement as begun at Crucible two ideas were advanced on decay Of timber by some of the officials: (1) That timber decay vas unusually rapid in the Crucible mine, and (2) that timber coated with rock dust decayed more rapidly than those teat were not so coated. There yore no records by which these ideas could be tested, and it appeared wise to make a limited; investigation particularly of the effect of rock dusting on decay, as rock dusting is an important means of preventing coal-dust explosions.]

Jan 1, 1940

By Herbert A. Franke

ANY analysis of the aluminum situation, particularly of the factors involved in the current shortage of the metal, must consider the rapid march of events since the Munich fiasco of September 1938. At the end of 1938, the sole domestic producer of aluminum had more than a year's supply of metal on hand, having added 50,500 tons of output to stocks during the year. Not until war had been declared between the United Kingdom and Germany in September 1939 did the United States begin to make serious preparations for defense and a limited national emergency was proclaimed. Congress reflecting popular opinion, was not disposed to spend huge sums for armaments in 1939, and although 31,413 tons of aluminum was withdrawn from stocks. 107,500 tons was still on hand at the end of the year. When the President initiated a 50,000-airplane program in May 1940 the country was astounded, as previous Congressional authorizations of approximately 6000 planes for the Army by July 1911 and 3000 for the Navy by 1914 had been considered adequate.

Jan 1, 1941

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Charles L. Kimbell

Virtually every available measure of total world mineral industry activity demonstrated that 1982 was little, if any, better for the industry than 1981 had been. Levels of production, trade, and consumption for virtually every major commodity declined; unit prices for most commodities fell, particularly in terms of constant dollars, and as a result of cutbacks in output and lower prices, capital available for investment within the industry was reduced. These conditions, coupled with the existence of considerable idle capacity, tended to retard investment, although there was an upturn in U.S. oil industry investment overseas. Despite the overall depressed situation of the world's mineral industry, there were indications of possible improvements in market economy countries near yearend, as output of some materials increased marginally and as prices for some mineral commodities reversed their downward trends. The downturns in total world mineral industry activity were not universal from the viewpoint of individual countries. Indeed, output of a number of commodities increased in centrally planned economy countries, and these gains were insufficient to offset declines in market economy countries, thereby sharply altering the proportion of total world output accounted for by each of these two groups of countries. There was a similar shift in consumption on a percentage basis.

Jan 1, 1984

By Steve Kral

In 2002, many in the mining industry — companies, academia and government — realized that the industry would soon be facing a serious shortfall in salaried and hourly employees. Depending on whose numbers are to be believed, 20 percent to 50 percent of current mining professionals are expected to retire within five to 10 years. And there are not enough students currently enrolled in mineral-related programs to the fill the need. Part of the impending shortage in professionals was brought on by the industry’s negative image, which discouraged students from enrolling in mining engineering programs. Another part was that the industry was in the doldrums and was seen by the public as a dying industry.

Jan 1, 2006

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By G. Konak

In-pit crusher location selection has had an important role recently, since increasing diesel prices. One way of reducing the haulage costs is to shorten the truck haulage distance by bringing the truck dump point into the pit. This study covers the work done on the optimum crusher location definition for a company that produces aggregate near Izmir, a city of Turkey located in the west. This paper will discuss the effects of pit geometry and mine access requirements on optimum crusher location selection that are mainly based on the establishment of minimum haulage distance. The method will be introduced first and then the computer algorithm developed for this study will be discussed later in the paper. Keywords: in-pit crushing, optimum location selection, optimizing haulage, computer aided design.

Jan 1, 2007

By T. R. Roy

A prediction model, developed by Central Mining Research Institute (India) for evaluation of fire risk rating of underground coal mine panels in bord and pillar working in respect of their proneness to spontaneous heating, is presented in this paper. The concept used in this model is innovative and user friendly. This model may be applied to a panel where extraction is carried out using any of the techniques: i) depillaring with formation of small pillars as final operation, ii) extraction by broadening of galleries, iii) depillaring with hydraulic sand stowing, and iv) depillaring with caving. Here, major fire risk parameters are short-listed and divided into three broad groups in accordance with the nature of their contribution to the spontaneous heating of a mine panel. The paper describes the procedure for estimating the fire risk rating of individual groups using separate objective type models developed for this purpose. Then it evaluates the overall fire risk rating of the panel by combining the fire risk ratings of all the three broad groups. The model is tested with the field data collected from different collieries spreading across the country and with the laboratory data for critical assessment of fitness. Keywords : prediction model, fire risk rating of panel, spontaneous heating of coal, underground panel, bord and pillar working.

Jan 1, 2003

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher's high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.' Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world's least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country's first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By William C. Hood

A leaching column technique that produces effluent similar in quality to coal mine drainage in the Eastern Interior Basin has been developed. The columns are charged with 1000 grams of crushed overburden and cycled through the leaching process once a week for twelve weeks. Inter-relationships among the important chemical constituents are very similar to those present in actual mine drainage waters, but the overall concentrations of ion are more dilute in the leachates. Multiplying the leachate concentrations by a factor of 4.5 gives values similar to mine waters. Available data suggests that each of the leaching cycles represents about three years of natural weathering, so that the leaching technique can predict the evolution of the mire drainage water over a time span of nearly 40 years. Use of the leaching technique with drill core samples should provide a method of approximating mine drainage quality in advance of mining and should be quite useful in identifying potentially toxic units in the overburden. However, the results should he considered to be a 'worst case' situation because the technique' does not consider the effects of reclamation.

Jan 1, 1984

By Simon D. Strauss

This article is part of a presentation Strauss made Dec. 3, 1988 at the sixth annual American Mining Hall of Fame (AMHofF) banquet in Tucson, AZ. At the banquet, the Mining Club of the Southwest honored Strauss by naming him the 1988 recipient to the AMHofF. (Industry newswatch, page 6). Introduction In the last two decades, there have been two previous periods of sharply rising copper prices. One was in 1973-74; the other in 1979-80. In both cases, a short period of high copper prices was followed by steep and prolonged periods of low prices. In the language of the market analyst, the high prices were called spikes. Is it likely, then, that three or four years from now the present price of copper will show up as a spike in the charts? There are substantial differences between the current position and the markets of 1973-74 and 1979-80. In 1973-74, US copper prices were subject to government-imposed price ceilings of $0.60 per lb through early December, 1973. These were increased to $0.68 per lb through May, 1974. Meanwhile, mines outside the United States were free of restraint. Rising demand in London pushed the price above $1 per lb in the third quarter of 1973. In early April 1974, it reached a peak of $1.50 a lb. In May of that year, the US ceilings were removed and the domestic price began to rise. What were the causes of this price strength? While ceilings held the domestic price below the world market, domestic consumers acquired all the tonnage offered by US mines. Meanwhile, in the world market, buyers feared prolonged shortages. The Club of Rome had warned that world economic growth would be limited by impending depletion of mineral resources. There was al so concern about a copper cartel that might increase copper prices even more. In early 1974, at a special United Nations session, developing-country spokesmen warned the industrialized world to expect high commodity prices. Also adding to the concerns of copper buyers was the fear that when US wage contracts expired in mid-1974, protracted strikes might ensue. The combined effect of this atmosphere was that consumers accumulated large amounts of copper, far above their normal carry. By midsummer, the position changed radically. While some strikes did occur in the United States, they proved short-lived. The most significant development was a massive economic recession. The energy crisis was causing enormous dislocations in the world economy. Construction activities were sharply reduced and automobile sales plummeted. Public confidence was shaken. Copper sales fell precipitately as consumers decided to draw down their swollen inventories. The price came down too. In April 1974, the London price- as noted-was $1.50 per lb. By the end of the year, it was down to $0.57 per lb. In 1973-74, the copper price rise was fed by fears of shortages, cartels, and strikes. In 1979-80, the market rose on the strength of good demand plus political and military instability. The price rise was also fed by inflationary trends, exemplified by speculation in precious metals. Prior to this second spike in copper prices, the market had been depressed despite economic recovery. Despite reduced US output, copper production in the rest of the world was increasing. Though consumption was rising, surplus stocks reached unprecedented levels. At the end of 1977, the aggregate of stocks at the refineries and in the exchange warehouses was 1.5 Mt (1.67 million st). That was more than three months' shipments at then rates of consumption. In 1978, the statistical position improved. Shipments of refined copper that year were 8% greater than in 1977. The result was reduced visible stocks but -just as was to be the case in 1984-86 - the price remained depressed. In 1979, an even sharper drop in visible stocks occurred as shipments rose by another 4%. This time, though, the price responded. In December 1978, the price in current dollars had been less than $0.70 per lb. By the end of 1979, it was above $1 per lb. And in the first quarter of 1980, it averaged more than $1.20 per lb. Military and political developments were a factor. The hostage crisis in Iran was followed by the Soviet invasion of Afghanistan. To many, it appeared that war might result if the Soviets pushed on into Pakistan. At the same time, speculation drove gold and silver prices to incredible levels. As silver prices rose above $40 per oz), copper above $1 per lb did not seem unreasonable. Then, in March 1980, the precious metals price boom collapsed. Copper prices also retreated, though not as much. In February 1980, the copperprice averaged $1.32 per lb. By December, it had dropped to $0.85 per lb. In 1981 and 1982, the decline continued. The present copper situation Why is the current situation different from these two previous episodes of high prices? First of all, today's inventories are far lower than they were in either 1974 or 1980, when the price declines began. The stocks at refineries and in exchange warehouses are substantially less than they were then. More significantly, consumers today have very limited holdings compared with stocks they carried in 1974 and 1980. Even if faced with a downturn in their own business, copper consumers will not be able to stay out of the market. To the extent they have any business at all, they will have to buy copper. And on the supply side, there is also a significant difference. The year 1988 has been unusual. US production is up sharply, responding to higher prices. But production is little changed in the rest of the Free World. Indeed, several of the major producing countries have mined less copper this year than in 1987 despite the prices increases. Peru has had labor problems that have cut its output. Zambia and Zaire suffer from shortages of expatriate technicians, not to mention spare parts. They also suffer from the failure to maintain equipment or perform adequate development. In Chile, the two largest mines, Chuquicamata and El Teniente, have not met their production targets. Chuquicamata is struggling with high arsenic content in its ore. And, in late 1987, severe rockbursts hampered operations at El Teniente. In addition, depletion of some mines in Australia and South Africa has offset rising output at other properties. Indeed, when final mine output figures for 1988 become available, it may well be

Jan 1, 1989

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By P. Venkatraman

Laboratory and pilot-scale test data have shown that the innovative feed presentation of the CrossFlow separator provides improved metallurgy when compared to traditional hindered-bed or teeter-bed classifiers. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Recent side-by-side industrial-scale evaluations have verified that this technology can improve overall efficiency, reduce the cut point of separation, and increase throughput capacity. This paper describes the important features that make this novel separator ideally suited for size classification and density concentration. Test data from heavy mineral, phosphate, and industrial mineral applications are also discussed.

Jan 1, 2005

By R. G. Aspden, D. A. Colling

THE {120}(001) texture has been reported in near 50 pct Ni-Fe alloys <0.004 in. thick1,2 and in copper 0.014 in. thick.3 This texture is one of two types of secondary recrystallization textures observed to replace a cube texture matrix and is desirable in Fe-Ni alloys because of its unique magnetic characteristics.1,2 However, the conditions for and mechanism of the {120}(001) formation are not well understood.3 During an investigation of the influence of alloying elements on the magnetic characteristics of 49 pct Ni-Fe alloys with a sheet thickness of 0.014 in., we have observed the growth of {120}(001) secondaries when strong deoxidizers such as aluminum and calcium were present. It is believed that this observation in unique and provides additional insight with regard to the mechanism for {120}(001) texture formation. Three alloys were prepared with electrolytic iron and nickel and contained a nominal 49 wt pct Ni. Alloy A was a straight binary Fe-Ni alloy, whereas intentional additions of 0.013 wt pct Ca to alloy B and of 0.59 wt pct A1 to alloy C were made. Ingots were forged at 1100 C, hot-rolled to 0.150 in. gage, pickled, and cold-rolled to 0.014 in. Standard U-shaped magnetic test specimens were punched, deburred, sprayed with MgO, and annealed in ~50°C dew point hydrogen. Textures were identified with the aid of etch pits, the

Jan 1, 1970

By Andrew Chapman

The scope of the SA (Situational Awareness) working group is to analyze the effectiveness of information delivery systems in mining equipment and develop a unified display design, to mitigate against the proliferation of screens within equipment cabs. This working group comprises a variety of stakeholders representing a cross-section of relevant mining and mining-related organizations. This stakeholder network will help guide the direction of the working group towards a common, mutually beneficial end. For now, the focus is on shovel displays; however it should be noted that this work is expected to form the foundation for similar work with other equipment in the future.

Aug 1, 2013

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Valentín Choquenaira Bombilla

El presente trabajo describe el proceso de automatización de la planta concentradora BHPBilliton deTintaya desde el punto de vista del usuario final y así proporcionar una visión global sobre los aspectos relacionados con la automatización de nuestro proceso a través de sistemas de control distribuido (Distributed Control Systems, DCS) e inteligencia artificial (Sistema Experto).También se describe la arquitectura del control, las formas de conexión (Hardware) y la función que desempeña dentro del sistema cada uno de los componentes del sistema de control distribuido instalados en la planta concentradora de sulfuros de BHPBilliton Tintaya S.A. así como algunos conocimientos básicos de manejo del sistema composer y conductor NT (Software) para realizar las funciones de configuración, monitoreo y control del proceso desde unidades remotas y estaciones de trabajo.

Sep 12, 2005

The Mineralogical Researches of Gold Ores and Technological Products at Operating Factory in Olympiada Mine (Russia)

Sep 13, 2010