Search Documents

By Katsuyoshi Kondoh

The utilization of silica particles originated in rice husks as reinforcements of magnesium composites was discussed. By using the solid state reaction of rice husk silica particles with magnesium powder, P/M magnesium based composites dispersed with the magnesium silicide (Mg2Si) and magnesium oxide (MgO) were fabricated. High-purity silica particles were originated from rice husks, one of the major agricultural wastes, via the citric acid leaching treatment and combustion in air. The effects of the silica particle characteristics such as size, crystalline and porous structures, on the reactivity of silica and magnesium to synthesize Mg2Si intermetallic were discussed. Amorphous silica was more useful for this reaction than crystalline one. The reactivity of rice husk silica was superior to that of the conventional mineral silica particles because of not only its amorphous structure but the larger specific surface area due to their pore structures. In the case of the green compact of the mixture of the rice husk silica and Mg powder, the silica particle size was not effective on the reactivity because the coarse particles were fractured into fine ones by cold compaction. The distribution of Mg2Si intermetallics of magnesium powder composites consolidated by SPS process was investigated by XRD and SEM-EDS analysis. Their mechanical and physical properties were also evaluated in detail.

Jan 1, 2009

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By John Frostiak, Lloyd Buckingham, Kenneth G. Thomas, Luis Wilson

"The El Indio roasting facility associated with El Indio Mine in Central Chile has operated since 1981. It is a facility developed to remove arsenic and antimony from gold bearing enargite/pyrite flotation concentrates.The three installed roasters are Nichols Herreschoff units each with 14 hearths and measuring 4.85 metres diameter. Hearths are rabbled by central shaft driven rabble arms. Product is progressively heated to 750°C under neutral to reducing atmospheric conditions to drive off labile sulphur, arsenic and antimony.Ancillary equipment includes skip hoist feed arrangements, water cooled screw conveyors for transporting and cooling calcine, gas cyclones, post combustion chambers, heat exchangers, electrostatic precipitators, bag houses, gas scrubbers and packaging facilities .Operating practices, history, mineralogy and results are reviewed. The improvements to arsenic and antimony extraction, ambiental conditions and environmental achievements are discussed.INTRODUCTIONHistoryThe El Indio property lies in the El Indio belt, a copper, gold and silver area approximately 175 km long by 10 km wide. The property is located in the Andes Mountains of the central part of Chile at latitude 30"" South and 160 km from the sea-side city of La Serena. Plant location is at 3850 meters above sea level.The property currently consists of two underground mines feeding the El Indio plant and an open pit feeding the newer Tambo leach plant. The property has been controlled by a succession of owners (St. Joe Minerals, Fluor, Bond Gold International and Lac Minerals Ltd.) before acquisition by Barrick Gold Corporation in 1994."

Jan 1, 1999

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By Rolf Schillinger

Blasting activities on the surface or underground necessarily involve the most sensitive aspect of environment remediation, human response or annoyance. Such effects are unavoidably characteristic of those activities. For this reason, blasting activities are governed by law and official regulations under surveillance of authorities, where companies and explosives engineers have to proceed within proper limits. Subject of the paper is a practical way of handling some necessary vibration standards being focused on blasting activities. The paper is based on the German Standard DIN 4150, Part 1 - 3, “Vibration in buildings”, Part 1: “Prediction of vibration parameters”, June 2001, Part 2: “Effects on persons in buildings”, June 1999 and Part 3: “Effects on structures”, February 1999.

Jan 1, 2006

By David Allen Jones

A depleted county gravel pit was rehabilitated by contracting an artist to convert it into sculpture, rather than using traditional reclamation methods. The sculptor's ideas were generally implemented as designed, but problems arose because of a faulty survey and severe weather. Public reaction was critical. A design symposium was presented by retaining six artists to prepare designs for varied sites. A public forum was offered and video-documented for broadcast. A new art-reclamation project grew out of this project.

Jan 1, 1981

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By J. K. Richmond

This is a progress report summarizing more than 5 years of a long-range Bureau of Mines research program. The purpose of this program has been to investigate the fire and explosion properties of Green River oil shale in the Bureau's Experimental Mine, in laboratories, and in the field. The lean limits of explosibility of oil shale dust, by small-and large-scale tests, are reported as a function of grade, ignition source, and particle size. A limited number of laboratory tests on the autoignition of oil shale dust layers and the spontaneous combustion tendencies of oil shale are described. Moderate-scale rubble fire tests were conducted to determine flame spread rates as a function of ventilation flow. With the aid of a system to continuously monitor methane emissions in a deep oil shale mine, the characteristics of the methane flow are reported as a function of ventilation and blasting procedures, and are compared with gas yields from core samples. Tentative predictions as to the emission of the methane to be expected in deep oil shale mines, far from the outcrop, are offered. Brief reference is made to a parallel investigation into the fire and explosion hazards of oil shale mining and processing by a Bureau contractor; detailed results of the latter investigation are to be found in the contractor's reports.

Jan 1, 1982

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By V. B. Dale

This report is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits in Gila, Yavapai, and Mohave Counties, Ariz. Many of the descriptions are taken from the reports of previous examinations by Bureau of Mines engineers, and from Defense Minerals Exploration Administration files. Where a previous examination had been made, and an inquiry disclosed that little or no work had been done since that time, pertinent information from the report was used in this paper with acknowledgment of the source. However, the majority of the descriptions is from field examinations by the author. In the past 3 years (July 1956-May 1959) only necessary annual assessment work was conducted on nearly all the properties described in this paper. There was no active mining on any of the properties examined.

Jan 1, 1961

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By M. I. F. S. Cruz, R. Pedersen, F. J. A. S. Barriga, A. Dias, A. F. A. Marques

"Underwater hydrothermal vents are known since the 1970s and their importance for the global economy is growing as new discoveries and new assessments are made each year (Cherkashov et al., 2010; Corliss et al., 1979). The similarities of seafloor massive sulfides, representing the younger versions of the well exploited on land volcanogenic massive sulfides, bring an increased awareness to the potential of the sea (Ajan G. Galley, 2007; Hannington et al., 2011; Herzig and Hannington, 1995). The Arctic Ocean presents itself as an opportunity to study new interest areas and numerous hydrothermal systems (active and inactive) were discovered along the Arctic Mid Ocean Ridge (AMOR) (Pedersen et al., 2010b). The Mohns ridge is an ultraslow spreading ridge of the AMOR (Vogt, 1986) where two hydrothermal vent sites were recently discovered, the Jan Mayen and the Loki’s Castle (Pedersen et al., 2010a; Pedersen et al., 2009; Pedersen, 2005). Here we compare these two Arctic hydrothermal systems, which represent two well-differentiated end-members of hydrothermal fields in the region."

Sep 1, 2014

By Valentine A. Chanturiya

The aim of this paper is basically to show progress in the study of nanosecond processes involved in the disintegration and breaking-up of mineral complexes with fine noble metals. We studied the influence of nanosecond High-Power Electromagnetic Pulses (HPEMP) on the physical and technological properties of refractory gold-containing ores and beneficiation products. Experimental data are presented to confirm the formation of breakdown channels and selective disintegration of mineral complexes as a result of pulse irradiation, which makes for efficient access of lixiviant solutions to precious metal grains and enhanced precious metal recovery into lixivia during leaching. Preliminary processing of gravity concentrate with a HPEMP resulted in significant increase of gold and silver extraction into lixivia during the cyanidation stage, with gold recovery increased by ~31% (from 51.2% in a blank test to 82.3% after irradiation). Gold recovery from stale gold-containing dressing tailings products increased after pulses-irradiation from 8-12% to 80-90%.

Jan 1, 2006

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Australia's iron ore industry is entering a challenging period with the development of new orebodies, the introduction of new products and the push for further downstream processing. In addition, the recent price reductions for iron ore exports have intensified the focus on reducing capital and operating costs. To assist in these areas, CSIRO is expanding its research capabilities, including the incorporation into CSIRO of the Mineral Processing Laboratories in Perth, which were previously managed by the WA Department of Minerals and Energy. In addition, a large part of the $24.4 million expansion of CSIRO's Pinjarra Hills laboratories in Brisbane will be devoted to enhancing iron ore processing research, providing purpose built laboratories and large process bays.

Jan 1, 1999

Newmont?s Twin Creeks Mine, located in northern Nevada, is producing gold ore from surface mining operations. The ore is currently processed at three different on site facilities depending on the ore type and the grade. The processing facilities operate under stringent geochemical blending constraints that must be met from mine ore deliveries and off site sourced ore. To analyze various strategic options, the technical team utilizes the mathematical optimization approach. However, due to the size and the complexity of the operation, there are unique challenges in optimizing life of mine production scheduling. This paper describes those challenges and the methodology developed to take advantage of different scheduling software systems that effectively compensate each other and result in reasonable guidance. The paper also describes how those scheduling results are reflected in detailed mine plan and cost estimate work.

Feb 27, 2013

By M. Rafie, M. Rinne, F. Samimi Namin

"SynopsisRock mass classification systems constitute an integral part of empirical underground excavation design. One system that is commonly used to classify rock mass is the Rock Mass Rating, or RMR, system. The RMR system has evolved over time to better reflect the perceived influence of various rock mass factors on excavation stability. While the introduced modifications have enhanced the applicability of this classification system, there are still areas that cause potential ambiguity. The RMR system cannot deal with input data ambiguities, uncertainties, and vagueness. To deal with the uncertainty, a Fuzzy Rock Mass Rating (FRMR) has been developed. This study aims to describe the main concept of the fuzzy approach, which is implemented in the FRMR to classify rock mass. The FRMR considers the uncertainty associated with the input data (uncertain variables) used in rock mass classification. The Gol-e-Gohar (GEG) area 3 iron ore deposits in the south of Iran were chosen as the case study for investigating the applicability of FRMR. The results of this study show that the FRMR software tool can easily be used for rock mass classification, even if uncertain input parameters have been used. FRMR consists of three parts, each of which is suitable for certain conditions.IntroductionNowadays, rock engineering classification systems, which constitute the backbone of the empirical design approach, are widely employed in both civil engineering and mining engineering. Rock mass classifications have recently been quite popular and are being used mostly for the preliminary design and planning purposes of projects. According to Bieniawski (1989), a rock mass classification scheme is intended to classify the rock masses, provide a basis for estimating deformation and strength properties, supply quantitative data for support estimation, and present a platform for communication between the exploration, design, and construction groups."

Jan 1, 2015

By H. Agnerian

"A survey of 925 mineral property transactions worldwide was carried out between 1987 and 2004. These mineral properties with reported Mineral Resources include 457 gold properties, 322 base metal properties, and five platinum group element (PGE) properties. Based on constant Canadian dollars, the results of the survey indicate that:• In general, unit metal values in the ground (e.g. $/oz Au or $/lb Cu) have kept pace with the changes in the respective metal prices during the period of the survey.• A general decrease in unit gold values in the ground has occurred from about $57/oz Au in 1987 to about $11/oz Au in 2002 for Canadian mineral properties, with the exception of a peak of $58/oz Au in 1996.• A similar trend for mineral properties has occurred in the United States, but with lower unit values, in the range from $1/oz Au to $10/oz Au during the last three years of the survey. • Unit metal values in the ground for gold properties in Canada were higher than for those in the rest of the world.• Unit metal values in the ground for copper properties in Canada were in the mid-range compared with other countries in the rest of the world; the United States and Australia were higher and Latin America, Asia, Africa, and Europe were lower than in Canada.• Unit metal values in the ground for zinc properties in Canada were also in the mid-range compared with other countries in the rest of the world; Latin America and Europe were higher and the United States, Australia, and Asia were lower than in Canada.• Unit metal values for nickel properties in Canada were highest compared with other countries in the rest of the world, followed by the United States, Australia, Africa, and Asia.• Gold values in the ground in Canada have ranged from 6% to 14% (with an average of approximately 10%) of the gold price.• The unit values of base metals in the ground have been in the order of 2% of the quoted metal price, during the period of the survey."

Jan 1, 2006

By Parviz F. Rad

The Bureau of Mines used a linear cutting apparatus equipped with a 7-inch disk cutter to cut grooves in marble, limestone, granite, and quartzite under a normal force of 7,000 lb. The size distribution of the muck for various grooves was determined through sieve analysis. A statistical search showed that Weibull distribution describes the size distribution better than other available functions. Results indicate that fineness modulus, chip population, and dimension of the largest chip can be used as indicators of cutting efficiency. The results correlate with those obtained from the boring machines and other lab experiments. Application of the principles established through this work to the operation of boring machines is explained

Jan 1, 1974