Search Documents

By Gerald E. H. Verbeek

As the number of driven concrete piles with Embedded Data Collectors increases, it has become possible to compare the widely used Beta Method to assess pile damage (using the change of pile impedance) with the so-called Measured Pile Integrity (MPI) method (a combination of two approaches using both the change of pile impedance and the change in pile pre-stress levels). After a brief introduction of both methods, this paper presents the outcome of that comparison based on data from more than 400 concrete piles driven in Florida, which brings into question the reliability of any damage assessment method based solely on the change of pile impedance (such as the Beta Method), especially to detect damage near the pile toe. Moreover the paper demonstrates the need to re-assess the damage classification used for the Beta Method as well as the use of Pile Driving Analysis (PDA) to detect pile toe damage.

Jan 1, 2011

By G. E. Agar, W. B. Kipkie, V. K. Drylie

"This paper describes mineral processing test work on drill core samples from an ilmenite deposit in Terrebonne County just north of Montreal.Mineralogical examination showed that the intimate associa¬tion between ilmenite and hematite precluded their separation. The maximum concentrate grade was therefore limited to 22.9% Ti. Liberation of gangue from the hemo-ilmenite grains occurred around 400 µm, a size which proved to be too coarse for recovery by flotation.Other physical separation techniques, such as elec¬trodynamic, magnetic and jigging, were tried in order to take advantage of the relatively coarse liberation size. An all-flotation procedure and a combination of jigging and flotation yielded similar separations.IntroductionInco Metals Company, through its subsidiary Canico, optioned an ilmenite deposit in Terrebonne County, just north of Montreal, and conducted a drilling campaign to confirm previous geological assessments of the deposit and to provide core samples for mineralogical study. Parts of these core samples were used for mineral processing studies, which will be described in this report. The objective was to identify suitable upgrading procedures, to determine the optimum combination of concentrate grade and recovery, and to provide suitable batches of concentrate for further treatment."

Jan 1, 1980

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By Göran Bäckblom

The Swedish mining companies LKAB and Boliden, the equipment supplier Atlas Copco, the general contractor NCC and the specialist company Reflex joined forces in 2005 to advance the field of rock technology for the purpose of mining and underground construction. The creation of the company Rock Tech Centre is part of the strategy developed by the Swedish mining industry to strengthen co-operation with industry, academia and society. This paper outlines the current R&D strategies developed for the industry in general, discusses what focus areas are selected and provides some details on the current RTC project portfolio, especially faster and better drifting.

May 1, 2006

By A. P. Squelch

The question of what stress condition exists in the hangingwall of tabular stopes remains topical and largely unanswered. Limited field data exist to quantify the situation and provide calibration for investigative computer modelling exercises. Work conducted in1989 and 1990 under a Chamber of Mines Research Organization (now the CSIR: Division of Mining Technology) programme of research into the behaviour and benefits of backfill may assist with this situation. The original work was motivated by the premise that the improved hangingwall stability in backfilled panels (identified by rockfall accident analyses) is due to a change in the hangingwall stress regime. Current, largely theoretical, studies into mechanisms of stope hangingwall behaviour and support interaction could benefit from considering these data. Keywords: Backfill, horizontal stress, stope hangingwall, hangingwall stability, support interaction.

Jan 1, 2002

By John J. Sammarco

Mining has one of the highest annual average fatality rates among major US industries. Health and safety dangers have been inherent to mining since the early days of picks and shovels. Even though miners’ health and safety has improved over the years, mining is still one of the most dangerous occupations. Mining was traditionally a low tech industry. It is now driven by competitive pressures to go high-tech by using programmable electronics (PE) for machine control, atmospheric monitoring and material processing. The industry’s experience with the functional safety of PE is limited compared with other industries. Thus, PE is an emerging technology for mining that can potentially create or worsen hazards.

Jan 1, 1999

By Sam S. Taylor

In most oil fields, natural gas is the major source of energy causing flow of oil to the well. The amount of gas produced With the oil generally exceeds actual energy requirements, so that in time the gas reserve of the field becomes seriously depleted and the oil production nest be stimulated by some auxiliary means. One of these is to repressure the oil formation with natural gas; or, where a gas supply is not available, often air is used. Although air is a cheap and convenient repressuring medium, its use sometimes is attended with several disadvantages. First, the return air-gas mixture decreases rapidly in fuel value, often until it can be used no longer as a source of power. At the same time, explosive mixtures may result if recycling is used, causing hazards to life and equipment. Second, some fields experience considerable trouble with the formation of emulsions which become increasingly difficult to treat. Although there is no definite proof that air repressuring always causes these emulsions, many operators are convinced that this is the case.

Jan 1, 1934

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By O. Q. Leone

A processing unit was developed for the complete cleaning of titanium alloy chips. The process uses solvent degreasing, magnetic separation, and anodic solution of nonmagnetic impurities in 10 weight-percent sulfuric acid. Vacuum arc-melted ingots weighing approximately 10 pounds each were prepared from cleaning chips according to ingot specifications.

Jan 1, 1973

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

By Jouko L. Lehtonen

Sheet pile walls can be sealed watertightly using various methods. The objective of this paper is to introduce a new innovation comprising the use of continuous cement grouting during embedding. The method has been tested on a field test site and installation and permeability features have been observed and analyzed. Installation can be carried out using traditional sheet piling machinery, merely some additional grouting equipment is needed. Installation speed of grouted sheet piles corresponds to that of conventional embedding. The permeability of the tested method is satisfactory in applications where e.g. polluted soil or water has to be isolated from the surrounding environment. In addition, this method can be used for conventional retaining walls where very low permeability is required or for reduction of soil vibration, e.g. close to a railway embankment. The new method to grout simultaneously and continuously during embedding has been developed based on respective innovations on impact driven steel piles.

Jan 1, 2006

By S. P. Ball, A. J. Monhemius

In a laboratory study under acidic oxidising conditions, the thiocyanate system gave results at least as good as cyanide and considerably better than thiourea, with modest consumption of SCN (less than 1 kg/t ore). For both cyanide and thiocyanate lixiviants a residence time of about 24 h was required for maximum gold extraction, which was generally in the range of 92-96%. The adsorption of gold from thiocyanate leach liquors was found to be rapid, but activated carbon catalyses the autoreduction of ferric iron to ferrous iron in thiocyanate solutions, suggesting that ion exchange may be a better recovery route

Dec 1, 1995

By P Mitchell, J Proffett, I Munajat

Batu Hijau is an island arc porphyry copper-gold deposit located in the southwest corner of Sumbawa Island in the Sunda-Banda archipelago of Indonesia. Southwest Sumbawa Island is underlain by Early Tertiary, low-K calc-alkaline to weakly alkaline volcanic and intrusive rocks. Within the mine area the oldest exposed rocks are medium- to thick-bedded, medium to coarse andesite volcanic lithic breccia, thin bedded, fine-grained volcaniclastic sandstones and mudstones and hypabyssal porphyritic andesite. In the eastern portion of the mine area there is a thick sequence of quartz diorite that postdates the andesites. A small stock of Equigranualar Quartz Diorite predates the Batu Hijau deposit and occupies the contact between the andesitic volcaniclastic sequence of rocks and the Porphyritic Quartz Diorite. Batu Hijau is a world-class copper-gold deposit that has a drill indicated mineable reserve of 914 million metric tonnes grading 0.525 per cent copper (10.58 billion pounds copper) and 0.403 g/t gold (11.8 million ounces gold). Mineralised material not in reserve accounts for an additional 580 million metric tonnes at 0.328 per cent Cu (4.19 billion pounds copper) and 0.171 g Au/T (3.19 million ounces gold), and including an oxide copper resource of 57 million tonnes at 0.37 per cent Cu and 0.12 g Au/T. Copper and gold mineralisation is directly related to quartz veining and wall rock alteration that developed with multiple tonalite porphyry intrusions. The tonalites were emplaced along the contact between the andesitic volcaniclastic rocks and quartz diorite intrusives. Copper and gold are zoned around the porphyry intrusions, which are designated by their contact-age relationships and other features as Old Tonalite, Intermediate Tonalite(s), and Young Tonalite(s). The Old Tonalite was the first copper-bearing intrusion, and although it is the smallest intrusion it has the highest quartz vein density, the strongest alteration and the highest grade. At least two tonalite porphyry intrusions followed the emplacement of the Old Tonalite. Each of these intrusions was associated with less quartz veining, weaker hydrothermal alteration and lower grade copper and gold than the previous intrusion. The intrusive cycle culminated with the emplacement of the Young Tonalite, which contains relatively few quartz veins, is weakly altered and mineralised. Hypogene hydrothermal alteration and sulphide mineralisation developed in five temporally and spatially overlapping stages. These stages consist of Early, Transitional, Late, Very Late, and I Zeolite alteration. Early alteration and sulphide mineralisation accompanied each tonalite porphyry intrusion, but with diminished intensity in each subsequent intrusion. Transitional and later stages of alteration and mineralisation postdate the tonalite porphyries and overprint Early stage alteration and mineralisation. Early alteration and mineralisation consisted of biotisation, secondary magnetite and plagioclase development, fine porphyry-style stockwork veining and ore mineralisation. Magnetite-biotite????quartz stringers and dark micaceous (biotite-sericite) veinlets were developed. The veinlets were accompanied by biotisation of magmatic mafic minerals and groundmass. Thin, irregular and discontinuous æAÆ type quartz veinlets and fine-grained chalcocite, digenite and bornite mineralisation accompanies the Early alteration. It is hypothesized that most of the copper mineralisation was originally deposited as bornite, digenite and chalcocite. Secondary plagioclase was added along the selvages of the early quartz veinlets. Early alteration is pervasive within and proximal to the tonalite porphyries. In the distal portions of the deposit, andalusite and anthophyllite formed at intermediate to shallow depths, and in the deeper portions of the deposit, respectively. The andalusite and anthophyllite probably developed at the same time as the early magnetite-biotite-quartz alteration in the core of the deposit. Transitional-age alteration consists of oligioclase/albite-sericite-chlorite- quartz-¦vermiculite and is associated with æBÆ quartz veins. Through-going planar æBÆ veins are thicker than æAÆ and æA-familyÆ veinlets and have chalcopyrite????bornite along vuggy centrelines and narrow oligioclase????albite alteration envelopes. Rare æCÆ chalcopyite¦quartz veinlets were also formed during Transitional alteration. During Transitional alteration early copper sulphide minerals (chalcocite, digenite and bornite) are converted to bornite and chalcopyrite. The majority of the copper (50 - 70 per cent) in the deposit is contained in ores in which chalcopyrite is the predominant sulphide. Late alteration consists of feldspar destruction and replacement by sericite and other minerals. The late alteration is accompanied by the development of æDÆ sulphide veinlets and veins. These veins consist of pyrite and quartz????chalcopyrite. Within the halos of the late pyritic veinlets biotite is replaced by sericite, quartz-sericite, quartz-andalusite, or quartz-pyrophyllite+kaolinite replace plagioclase, and magnetite is converted to specularite and/or pyrite. In the periphery of the deposit, the feldspar destructive alteration, together with outer zones of Transitional-age alteration, constitutes what is commonly referred to as a æpropylitic zoneÆ. Very Late hydrothermal alteration is also characterised by feldspar destruction, but differs from Late alteration in that feldspar is replaced by smectite in association with sericite and chlorite. Sulphide mineralisation in this stage consists of sphalerite, galena, tennantite, pyrite and chalcopyrite. The last stage or I Zeolite alteration consists of low-temperature, open space filling consisting of stilbite or laumontite¦calcite. Supergene oxidisation of the orebody extends to a maximum depth of 210m. Isolated deep oxidation occurs along open fracture zones to depths of ~400 metres along æDÆ vein filled fracture zones. Weak supergene copper enrichment occurs in a thin horizon (15 to 60 m thick) that blankets the top of the deposit. The main supergene copper mineral is secondary æsootyÆ chalcocite replacement of sulphide grains and as veins.

Jan 1, 1999

By D Craw, R Norris

The Golden Bar pit is part of the Macraes mine, the largest gold mine in New Zealand. The Macraes mine is mainly developed in the late metamorphic Hyde-Macraes Shear Zone. However, the Golden Bar pit was developed in a mineralised zone about 200 m structurally above the Hyde-Macraes Shear Zone. The host rocks are dominated by massive quartzofeldspathic schist (5 - 10 m layers) with minor intercalations (1 - 5 m scale) of micaceous schist. All the host schist has disseminated pyrite (micron to mm scale) from pervasive late metamorphic hydrothermal alteration.   In addition, there has been more localised (metre scale) relatively intense hydrothermal alteration controlled by shears subparallel to foliation. Gold occurs in three types of mineralised rock: silicified schist, which dominates, fissile black sheared rock, and cross-cutting quartz veins. There are three principal structural zones in the deposit: 1.   a strongly sheared micaceous and graphitic zone at the base of the structural sequence; 2.   a weakly deformed schist zone cut by relatively flat-lying (= 20¦ dipping) quartz veins; and 3.   a stack of imbricated schist pods and deformed silicified schist confined between two sub-parallel low-angle (ca. 30¦) shears.   These structural zones were juxtaposed during thrust deformation. The lower black shear zone has m-scale folding and over-thrusting packages, kink folding and foliation stacking with associated striations that imply west-directed thrusting. Striations and imbrication geometry between the upper two shears imply oblique thrusting that was directed towards the west. Post-mineralisation normal faults locally disrupt the mineralised zone. The Golden Bar pit mineralised zone has some of the structural and mineralogical characteristics of the main Hyde-Macraes Shear Zone, and may be genetically related.

Jan 1, 2006

Common practice in mineral resource estimation consists of partitioning the orebody into several domains defined by grade intervals, prior to the geostatistical modelling and estimation/simulation at unsampled locations. This paper shows the pitfalls of grade domaining through a case study in which we compare the performance of several estimation schemes and demonstrate that the use of domains defined by grade cut-offs implies a deterioration of the resource estimates, mainly in what refers to precision and conditional bias. Then, several conceptual limitations of the grade domaining approach are stressed, in particular the fact that it does not account for the spatial dependency between adjacent domains and for the uncertainty in the domain boundaries. Also, this approach is shown to be sensitive to the cut-offs that define the domains, to provoke artifacts in the kriging maps, histograms and scatter grams between true and estimated grades, and to lower the kriging variance, a feature that may impact the mineral resource classification. An alternative approach is finally proposed to overcome these limitations, based on a stochastic modelling of the grade domains and a co-kriging of the grades using information from all the domains. Keywords: geostatistics, kriging, conditional bias, geological control, grade zoning.

Jan 1, 2005

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By B Brown, P J. Hommert, B J. Thorne

"Early attempts at estimation of stress wave damage in blasting by use of finite element analysis met with limited success due to numerical instabilities that prevented calculations from being carried to late times. A"" improved damage model based on microcrack growth in tension allows finite elementcalculations which remain stable at late times. Estimation of crater profiles for blasting experiments in granite demonstrate successful simulations with this model."

Jan 1, 1990

By Jack Touseull

On November 15, 1972, the Bautsch mine, a lead-zinc mine in Paleozoic dolomites, experienced a massive rock failure involving 3 to 5 million tons. Because this failure was large and extended to the surface, it was included in the Federal Bureau of Mines investigations on "Massive Rock Failures." Analysis of the rock mechanics and mode of failure revealed that failure at the Bautsch mine was the result of the interrelationship of many factors. Factors related to the failure were found to be external and internal to the mining environment. Unlike internal factors, external factors were not apparent and, therefore, many external factors were investigated; some of which are not normally considered in rock mechanics analyses. External and internal factors determined to be of significant importance were: (1) precipitation, (2) fractures, (3) plastic clay layer, (4) topography, (5) rock alteration, (6) bedding, and (7) mining zone dimensions. Because of the conditions at the mine, failure could have been predicted without extensive instrumentation. Application of basic geologic and engineering principles to the internal and external factors could have predicted failure. Alternately, failure would, in all probability, have been delayed by years if, after 1962, mining had been curtailed in the area of failure.

Jan 1, 1980