Search Documents

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

Outsourcing of specialist and non-continuous services is common practice in international mining operations. There is an increasing trend towards this practice in South Africa as a result of the major organisational changes that have taken place in the industry, and as lower revenues and production cost pressures have reduced profit margins. Many specialist functions have been outsourced in the industry for a long time, an example being shaft sinking, which is undertaken by specialist shaft sinking contractors. In the professional services area, some activities have been outsourced, for example the design and construction supervision of tailings dams, but mining related activities such as geology, mine planning and scheduling, engineering, ventilation, and rock engineering, have traditionally been carried out by in-house staff. In this paper some of the industry problems which have led to an increase in outsourcing of professional services are considered. Then the pros and cons of outsourcing are dealt with before outlining the factors which should be taken into account in choosing an outsourcing partner.

Jan 1, 1999

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

By Dale Bartholomae, David Harrison, Edward J. Walter

Methods that involve the use of signature blast holes in order to identify the particular frequency characteristics of a geographical area are widely available. Information acquired can be used to determine optimum blast hole timings to produce the desired constructive and destructive inference. However, these types of analyses can be both complicated and expensive. This study will investigate the use and practicality of signature hole and/or shift and sum analysis software and their application to small diameter construction utility blasting operations in Pennsylvania and faster moving projects in general. A determination will then be made as to whether this technology can be utilized by today’s blaster, from both a functional and a cost effective basis. Single hole blasts will be detonated on various smaller construction projects and will be monitored with an array of seismographs. The collected data will be analyzed in order to determine the optimum timing between holes to produce the preferred frequency content while keeping in mind the explosives user’s current inventory of blasting supplies.

Jan 1, 2005

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

Plant-Based Trials of Monitoring of Coal Flotation Systems Using Electrical Impedance Spectrum Technique

Sep 13, 2010

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Elli Nurminen

In this work the thermodynamics of the metallic sulphate decomposition reactions were studied through thermodynamical calculations and thermogravimetric methods. The decomposition temperatures and mechanisms were determined for cupric sulphate, ferric sulphate and also for industrial flue dust from a copper flash smelting process. The aim was to determine the thermodynamic conditions for sulphate decomposition and to estimate whether the reactions are kinetically likely to take place in the flash smelting process heat recovery equipment. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process.

Jan 1, 2006

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By Sam G. Demou

Drag bit cutting tests were conducted chiefly to determine bit forces encountered in rock types representing a range of compressive strength and hardness and thus enable the design engineer to estimate a continuous miner's performance in a range of rock types. Testing was carried out on the Bureau of Mines uniquely designed, instrumented rock cutting device (RCD). This device can make 3-ft-long cuts at various depths and speeds to approximate full-scale drag bit cutting by continuous miners. Point attack and cutter bits were tested on four rock types ranging in compressive strength from 7,200 psi (trona) to 29,600 psi (Valders white rock). Cutting tests were made at depths up to 1 in and speeds up to 70 in/sec. Data included normal and cutting forces, groove depth, groove width, and weight of rock broken. The effect of varying the cutting speed was determined, and specific energies were calculated for the various conditions. The bit wear was also observed. For the rocks tested, compressive strength and hardness are good indicators of forces, specific energy, and wear encountered. Results, especially bit wear observations, show the possibility of extending continuous miners, already being used in trona, to Indiana limestone (10,000 psi). Rapid bit deterioration precludes use in Tennessee marble (16,800 psi) and Valders white rock (29,600 psi).

Jan 1, 1983

Develop tools that mine personnel can use to comply with 30 CFR,Part 47. Background The new MSHA rule, 30 CFR, Part 47 (also known as the HazCom rule), requires all mines to develop a written program to track hazardous chemicals at their sites. More specifically, the rule requires that mines list all chemicals and determine which are hazardous; develop a written Hazard Communication Program; label all containers used to store hazardous chemicals; obtain or develop Material Safety Data Sheets (MSDS) for all chemicals stored or produced; provide miners with training in working around hazardous chemicals; and make information about hazardous chemicals available to all workers. All mines with six or more employees must have complied with the new rule by September 23, 2002, and mines with five or fewer employees will have to be in compliance by March 21, 2003.

Mar 1, 2003

By E. L. Singleton

The Bureau of Mines investigated extraction of aluminum from aluminum-silicon alloys as a means of utilizing domestic aluminum silicate ores for aluminum production. Aluminum was extracted from aluminum-silicon alloys by electrolysis in molten electrolytes of NaCl-KCI-AIC13 and NaCl-KCI-AIF3 in a laboratory-scale cell. Six alloys with aluminum contents ranging from 20 to 87 percent aluminum were tested, and aluminum products of primary grade or better were obtained. More than 80 percent of the aluminum was recovered with current efficiencies as high as 91 percent. Recovery of a metallurgical-grade silicon product from the anode residue by an acid leaching procedure was possible with the 50-50 and 65-35 Al-Si alloys.

Jan 1, 1972

By R. V. Ramani

"A computer simulation model of a dragline has beer developed for the study of alternative dragline deployment schemes for varying geological and mining conditions. In this paper, the mathematical aspects of the model, the input data and output results are discussed. An application of the model to a coal mine in eastern Kentucky is presented.IntroductionDraglines are very productive machines. To extend their operating ranges, they are operated in several modes such as advance benching, key cut, extended benching and pullback. Unfortunately, these variations result in low machine productivities. Appropriate methods to operate these machines must be developed on the basis of detailed analyses of dragline performance under varying geological and mining conditions. There are several standard engineering procedures for the selection of dragline, and design of a dragline pit (Ramani, Iroegbu and Manula, 1976). However, the complex interrelationship which exists among equipment, methods and natural conditions can be quantified only through orderly and systematic experiments.Computer simulation is well suited to studying these types of equipment selection and method layout problems. Several alternatives can be analyzed in a relatively short time by the modification of input variables. Also, the application of computer simulation models can significantly reduce the manpower and cost required for such analysis."

Jan 1, 1985

By Grafton Thrasher

For the proper discussion of this subject it is necessary to incorporate in this paper the substance of part of an article published by rite in Metallurgical and Chemical Engineering for January, 1915. CAST-IRON TEST PLUG, SHOWING LOW MOTTLED AND MOTTLED FRACTURES. Several years ago, while I was thief chemist for a malleable-iron company, it occurred to me that the mere regulation of silicon was not sufficient to produce the desired degree of chill. But only after repeatedly encountering this fact in befit open-hearth and air-furnace, as well as cupola metal, was I led to regard variation in the total carbon as the principal cause of disturbance; and I resolved to determine the total carbon as well as the sill on ill every heat, and by a carefully prepared test piece to gauge the approximate degree of chill. The test piece selected was a round plug, 2 in. in diameter and 12 in. long, cast on end

Jan 10, 1915

By Stephen C. Tadolini, Steve Bessinger, James Pile, Christopher Mark

The San Juan Coal Mine, located near Farmington, New Mexico, supplies the San Juan Generating Station with more than 6 million tons of coal annually. To replace dwindling surface mine production, San Juan installed a longwall in 2002. The roof rock in much of the underground reserve consists of interbedded coals, carbonaceous shales, and mudstones. Roof support consists of fully-grouted roof bolts, both tensioned and non-tensioned, supplemented by modified cable trusses. Short-encapsulation pull tests conducted by San Juan’s geotechnical engineering department showed that some of the immediate roof layers provided variable bolt anchorage. To ensure that the roof bolts were obtaining the necessary anchorage, additional tests were conducted in a variety of locations. The results have been used to determine the optimum support design for different areas of the mine. Another series of tests evaluated the performance of several bolt and hole diameter combinations. The experience at San Juan Mine shows that short-encapsulation pull tests can provide the information necessary to improve ground control in variable roof conditions. It also illustrates how a pro-active geotechnical engineering program can be an essential component of a state of the art underground coal mine.

In line with DML Resources continual forward management policies, the Roscommon Quarry operation has recently installed and commissioned a Nordberg 7 ft Symons cone crusher and a HP 300 cone crusher. Both machines have enhanced the production capabilities and quality control of the Roscommon comminuition circuit and they will provide efficient and reliable crushing well into the next century.

Jan 1, 1994

By K. J. Liles

Research was undertaken by the Bureau of Mines to determine the technical feasibility of producing lightweight aggregate from the waste glass fraction of municipal incinerator residues. Tests were conducted to determine the amount and optimum size of glass, the amount of sodium silicate, and the method used to form the material to be expanded. The most suitable mixture, 78 percent glass, 20 percent clay, and 2 percent sodium silicate, was pelletized and then expanded by exposure to a temperature of 1,550° F for 15 minutes The resulting lightweight material had a bulk density of 38 lb/cu ft and exhibited excellent pore structure. Concrete test cylinders made from the light weight aggregate had a unit weight of 104 lb/cu ft and a compressive strength of 2,550 lb/sq in after a 28-day steam cure.

Jan 1, 1976