Search Documents

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Sudhir Kumar Kashyap

In underground activities ground control is a challenging problem. It affects safety, production, and efficiency. As per statistics of accident data, ?fall of roof/sides? is one of the major causes of mine accidents. In many cases, our experiences and understanding of soil and rock behavior still fall short of being able to predict how the ground will behave. Presently, empirical approaches to design are widely used in estimating mine support parameters. Under these circumstances, expert judgment plays an important role, and such accidents can be obviated with accurate measurement and optimization of data and analysis using the neuro-fuzzy technique of artificial intelligence. Recently, a neuro-fuzzy hybrid approach has become one of the major areas of interest in engineering fields because it gets the benefits of neural networks as well as those of fuzzy logic systems, and it removes the individual disadvantages by combining them on the common features. Neural network and fuzzy logic technologies have common features, such as a distributed representation of knowledge, the ability to handle data with uncertainty and imprecision, etc., like in ground control. Fuzzy logic technique has tolerance for imprecision of data, while neural networks have tolerance for noisy data. In this paper we have focused an intelligent technique, i.e., neuro-fuzzy technique, to approximate the setting load given to the standing support (props) erected for the purpose of supporting freshly exposed roof during underground mining. We have used twelve input variables of rock parameters, and after having trained using a neural network with a sigmoidal function as an activation function, simulation was done to find the output parameter, i.e., the pre-load (setting load)to be applied on props. Outputs of the neural network were again fed to the fuzzy system together with the twelve parameters, incorporating five triangular membership functions for each parameter. Final optimum output was approximated using the MATLAB program, which was found to be satisfactory. Neuro-fuzzy technique has better performance over individual neural networks or fuzzy logic technique.

Jan 1, 2012

By Jinsheng Chen, S. S. Peng

The relationship between support performance parameters and parameters representative of mining and roof conditions is characterised by uncertainty, non-linearity and dependence, so the theory of artificial neural networks was selected as a basis for shield design. A computer program based on a back-propagation training algorithm was written to derive the weighting factors between inputs and outputs from field data; once these had been established two mathematical models were developed to describe the relationship. Back-calculation of field data indicates that the results generated from the neural network models are much more accurate than those derived by traditional methods and can be used with a higher level of confidence. The support density, possible yield frequency of face supports and interval of periodic roof weighting under specific mining and roof conditions can be determined by application of the models

Jun 21, 1905

By P. T. O'Kane

"INTRODUCTION Wright Engineers Limited is active and has extensive experience in the design of pressure oxidation plants for the treatment of refractory gold ore and concentrate. In addition to the Mercur oxidation facility, similar projects undertaken during the last few years include the 3000 ton per day acid oxidation plant for the Getchell Mine, Nevada, a concentrate treatment autoclave for Asamera in 1984 and a feasibility study of a 50-tons per day autoclave plant for Consolidated Professor's Duport property in Ontario. The Equity Silver antimony and arsenic precipitation autoclaves, and the low pressure autoclaves at Key Lake Uranium in Northern Saskatchewan were also engineered by Wright in recent years.In August 1986, Wright was retained by Barrick Resources (U.S.A.) Inc. to add a 750 tpd pressure oxidation circuit to the existing mill at their Mercur Gold Mine, Utah. This paper describes this facility and outlines the start up in the spring of 1988 and subsequent successful operation. MERCUR OPERATION The Barrick Mercur Gold Mine is located at the south end of the Oquirrh Mountains in Tooele County, Utah. The carbon-in-leach (CIL) process plant camnenced operation in 1983 with a design throughput of 3000 tpd and has since been expanded to handle rrore than 5000 tpd. 'IWo ore types are mined, an oxide ore and a refractory ore, which is by Barrick's definition ""an ore from which less than 60% gold extraction is achieved by a standard CIL amenability test."" Typical of many sulphidic/carbonaceous ores, the refractory gold does not respond well to the cyanidation process. As a result, refractory ore has been stockpiled since the start of mining. As of June 1987, Mercur had about 570,000 tons of refractory ore stockpiled and 5.7 million tons of proven and probable reserves, grading 0.06 oz/t including approximately 3.5 million tons of tailings from the previous operation grading 0.55 oz/t. In 1986, Barrick decided to build a 750 ton per day pressure oxidation plant to process these ores. The process, for which a patent was granted, comprises pressure oxidation of the sulphides in an alkaline environment. It was developed in 1981 but was set aside in preference of a CIL plant treating only oxide ores by the previous owner of the property, Getty Oil. This process is capable of increasing gold recovery from the refractory ore from as low as 35% by conventional CIL processing to more than 85%. In 1986 Wright Engineers was engaged to undertake a feasibility study based on batch testing. This lead to a decision by Barrick Mercur later that year to build the commercial pressure oxidation plant. Wright was awarded the contract for engineering, procurement, construction managernent and commissioning in March 1987. The plant was mechanically complete in January 28, 1988, and was in operation by February 1988."

Jan 1, 1989

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

By J. Lee, R. G. Rosehart

"The basic problem of arsenic contamination from mine water is discussed. Effective methods of removal involving chemical precipitation, activated carbon adsorption, ion exchange and reverse osmosis are discussed. As well as an economic analysis, detail is also paid to other ions in solution which are removed simultaneously.INTRODUCTIONThe object of this paper is to review arsenic and its removal from gold extraction plant effluents. The first method considered is chemical precipitation. A second method is sorption processes, such as ion exchange resins and activated carbon adsorption. A third method is the possible application of reverse osmosis for the treatment of mine waste waters containing arsenic.Arsenic pollution in the gold mining communities of Canada and Ghana have been extensively studies (l, 2). Lynch(3) Shabunin, Gutman and Kogan( 4), Hollo, Troth, Vennes and Illinigi (5) and Hau(6) have reported their removal methods of arsenic by chemical precipitation, ion exchange and biological methods. Their conclusions were that the precipitation with Fe2+ and Fe3+ ions was most effective.Scope of the ProblemInitial aspects of this research program involved a detailed analysis of the operation of a gold extraction plant located in Canada. The name and location of the mine is proprietary information. Figure 1 gives a basic process schematic with the main tailing streams identified.Table 1 gives information as to the various mine streams and their physical and chemical composition. In this study, primary attention is paid to the removal of dissolved arsenic from waste waters. Solids from this type of operation can always be back-filled. As could be anticipated, the dissolved As content of the primary flotation tailing stream is very low. The dissolved As level in the secondary processing stream and the roasting quench water is quite high. The reason being that at this stage of the process, the arsenic has been freed from the arsenopyrite forms."

Jan 1, 1972

By Francis E. Federspiel

In 1984 and 1985, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 87,720-acre South Boise Yuba study area (formerly known as RARE II Wilderness Recommended area I-4553) to evaluate mineral resources. The study area and additions are in Blaine, Camas, and Elmore Counties, 10, about 60 mi east of Boise. Granitic rocks of the Cretaceous age Idaho Batholith occupy the western two-thirds of the study area. A Tertiary age granitic complex has intruded, and broken into small blocks, Paleozoic age sedimentary rocks in the eastern third of the study area. Tertiary Challis Volcanics overlie both of these rock types. Principal mineralized structures are gold-and silver-bearing quartz veins and shear zones trending northwest to easterly in the Cretaceous granitic rocks. Copper, lead, and zinc are accessory metals in many mineralized structures.

Jan 1, 1987

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By McHenry Mosier

This paper describing mining practice at Morenci, Ariz., is one of a series of articles on mining method, and practice in the various mining districts in the United States. At present (1929) practically all the mineral production in the Morenci district is from the Humboldt mine of the Morenci Branch, Phelps Dodge Corporation. The mining method used is adapted to the type of ore body being exploited; it has been developed by adopting methods used elsewhere and making necessary changes to fit local conditions. Improvements in current practices are still being made.

Jan 1, 1929

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By M. A. Hermanus

This paper examines the occupational health and safety performance (OHS) of the South African mining sector against the backdrop of changes in the composition of the sector, international trends in OHS performance, and the agreement on OHS milestones and targets by mining stakeholders at the Mine Health and Safety Summit of 2003. Although OHS performance has improved, progress is slow and there is need for significant rather than incremental change if the targets are to be realized. Since 2003, fatalities and injuries are 20?25% short of annual milestones and not all commodities show consistent improvement. Statistics on occupational health impacts are unavailable, but noise and respirable dust levels are known to be high in mines, with much work lying ahead to address exposures at source. Trends in regulating and addressing OHS hazards are discussed with reference to the notion of ?systems-thinking? and the targets. Efforts to improve OHS and to respond to changes in the sector are constrained by a lack of training and consistency in risk management, guidance for junior, small and artisanal miners, and holistic approaches to risk. For example, treating risk holistically would involve taking proper account of contractors and women in the workplace, and attending to human factors and ergonomics.

Jan 1, 2007

By Leonard Obert

Part I of this report3/ proposed a sonic method for determining pressure, in situ, on rock pillar, arches, and other structures. The method required (1) a laboratory determination of the variation of the velocity of sound with pressure in samples of rock taken from mine pillars to establish a velocity pressure relationship for the type of rock, and (2) a measurement of the velocity of sound in the mine pillars from which the laboratory samples were taken. The pressure on the pillars could be determined by correlating the velocity in the pillar with the velocity-pressure relationship established in the laboratory. The success of this method depends on the extent to which velocity of sound varies with pressure. Furthermore, Young's modulus of elasticity, E, can be calculated from longitudinal velocity, V, by the relationship, E = V2d ...(1) where d = density. Hence, the variation of the elastic modulus with pressure also can be determined. It pointed out that this method might be extended to assist in the prediction of rock bursts, inasmuch as the rock is subjected to extreme pressure in these instances.

Jan 1, 1940

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992

By J. B. Czirr

MESA Corporation has completed a four-year program for the Bureau of Mines to develop a technique for measuring roof competence in underground coal mines. The preferred technique employs a tracer gas that is injected into a roof borehole drilled near the working face. The tracer gas performs the dual purpose of determining the pressure loss rate from the borehole and of marking the diffusion pattern of the the escaping gas. The primary detection technique relies upon observation of the rate of pressure drop in a hole drilled in the roof strata under test. If this measurement indicates a significant probability of roof collapse, the gas diffusion pattern is outlined with the Leak-gun tracer-gas detector. These two techniques provide a comprehensive method for predicting the relative probability of roof collapse in operating coal mines.

Jan 1, 1985

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

The Performance of Benzyl Arsonic Acid as a Collector in the Flotation of Wolframite and Cassiterite Slime

Sep 13, 2010