Search Documents

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

RME has a vision for a new grinding plant operational paradigm made possible by RME's fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply `must do' maintenance functions. Taken to the extreme, liner profiles may prove capable of `tuning' a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RME's range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RME's vision of a `liner profile versus profitability' commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

Precision surface mining is increasingly occupying a significant role in open pit mining. Improvements in technology now allow continuous surface mining of material well above 140 MPa (20 300 psi) efficiently and cost effectively when compared to drilling and blasting/primary crushing methods. These include the elimination of the use explosives and primary crushing, the ability to precisely extract the ore from the waste, or separate ores of varying chemistry and mine thin seams and non-homogenous orebodies cost effectively. In addition, precision surface mining extends the useful life of a mine by extending the mine boundaries. It can expand production capacity in existing mines and is particularly cost effective in greenfield start-up mines. Precision mining techniques result in higher percentage recoveries. This paper reviews several of these techniques for the Terrain Leveler« surface excavation machine (SEM), and shows their impact. Vermeer's current approach to precision surface mining is utilisation of the T1255 Terrain Leveler SEM. Several units have been proven in round-the-clock, seven day operations throughout the world. Among other innovations are design simplicity, stability, maneuverability, rear-mounted tilting drum and top-down cutting. The impact of these items are discussed in more detail in the paper. After a detailed analysis of the importance of machine availability on overall mine performance, Vermeer has extended its equipment line to include a direct-drive option for its T1255 Terrain Leveler SEM. In addition, improvements in dust suppression are presented. While the T1255 Terrain Leveler SEM is of optimum size and cost in small and medium sized mines, Vermeer has recognised that larger mines require larger machines with increased capacities. Vermeer will prototype the T1655 Terrain Leveler SEM later this year. Specifications of this machine and up-to-date preliminary results are presented. A discussion of the role of each machine size and driving mechanisms are included. Finally, the next stage in Vermeer's providing solutions to the surface mining community will be described - a continuous loader. The impact on current mine planning is presented using a detailed computer program developed for studying the impact of loading techniques and higher production rates on mine plan optimisation.

Dec 6, 2010

[COUNCIL FOR 1991/92 President R.D. Beck President Elect JP. Hoffman Vice Presidents Senior Junior Dr H. Scott-Russell J.A. Cruise Immediate Past President Honorary Treasurer H.G. Mosenthal J.A. Cruise Members of Council Dr N.A. Barcza G.A. Brown B.R. Broekman Prof. RJ. Dippenaar B.R. Fleetwood* J.S. Freer P.R. Janisch P.J. Knottenbelt Dr J. Lurie R.P. Mohring *Co-opted K.C. Owen P.D.K. Robinson D.A.J. Ross-Watt P. Smith K.A. van Gessel DJ. van Niekerk P. van Schaardenburgh* CJ.C.J. van Vuuren* P.M.T. White]

Jan 1, 1992

By E K. Leeka

Process control limitations have led to suboptimal performance of the crushing section of Sishen MineÆs Jig Plant. The performance of the PID (proportional-integral-derivative) controller implemented during commissioning was hampered by the relatively small buffer capacity between the crushers and screens. The inability to maintain the tertiary crushing chamber under full choke conditions lead to inefficient crushing and reduced crusher product cubicity.Model predictive control (MPC) was implemented in the tertiary crusher plant in May 2012 and resulted in a throughput improvement of six per cent in its first month. The controller was further optimised and indicated a throughput improvement of 16 per cent during on/off testing in July 2012. The throughput improvement is attributable to the finer crusher product resulting from operating the crusher under full choke conditions and controlled feed rate to the tertiary crusher plant screens. The next step is to couple the model predictive controller, automated gap control system and an economic optimiser to ensure maximised throughput and value from the resource.CITATION:Leeka, E K, 2013. Performance of model predictive control on the crushing circuit at Sishen Mine, in Proceedings Iron Ore 2013 , pp 417-420 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Holdgate G. R, Thompson B. R, Webster R. L, Bolger P. F

The Gippsland Basin in south-eastern Australia has an area of approximately 46 000 sq km. It is one of the world's major coal and petroleum bearing basins, with most of the former occurring in the smaller one fifth on-shore part. The stratigraphy, structure and economic resources of the Tertiary sedimentary pile is now well known through extensive drilling for coal and petroleum. In contrast, the older Cretaceous sequences through their lesser economic importance are relatively less explored. The sedimentational history of the Gippsland Basin has largely followed along similar lines of development to the many other southern Australian basins since the Cretaceous break-up of Gondwanaland. However, the scale of accumulation of coal and hydrocarbon source rocks is unprecedented and differentiates this basin, for reasons less well understood, from the others. Large scale open cut brown coal mining since the late-1920s has been carried out in the western extremities of the basin, while vigorous extraction of some two thirds of Australian petroleum products taken place in the offshore part. Brown coal seam thicknesses and economically winnable reserves are huge and outrank most other brown coal basins of the world. Development of the resource currently meets the need for electricity generation throughout the State of Victoria, but other future developments such as conversion to oil, being investigated.

Jan 1, 1992

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By Clarence R. Zink

A problem has always existed in deep and fast drilling situations such as coal overburden drilling, or when drilling with a tight annulus, such as 9 7/8" bits and 8 5/8" pipe. This problem is the difficulty experienced by blasthole bit and blasthole drill rig manufacturers to attain large jumps in bit and drill rig productivity through bit and rig design, when drilling in these specific situations. In other drilling situations, these large jumps in productivity have been easily attained.

Jan 1, 1998

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By J Guo, K Williams, S Caldwell, W Chen

Mining is increasingly occurring near or below the water table. This has led to a higher rate of handling problems associated with increased moisture and increased adhesion, which lead to a higher rate of blockage events within the materials handling chain. Typically, these ores and minerals are known as ‘wet and sticky materials’.Currently there is very limited knowledge and/or methodologies for effective design of efficient materials handling systems when it comes to handling wet and sticky materials. However, there is one major parameter that significantly affects handleability of a wet and sticky ore; namely, its moisture content. Flow property testing has shown that when moisture is reduced, the adhesive properties of the ore are also significantly reduced, thereby increasing ore flowability.The research embodied in this paper investigates the moisture reduction rate through a loose packed bed of iron ore using dry, ambient temperature airflow. A comparison of the predictive capabilities of a proposed drying model to data obtained from on-site experiments using iron ore fines is made. Building on an assumption made by Hukill (1954), a second term has been proposed to account for rewetting effects in the drying process. From this research, identification of improved moisture reduction approaches is envisaged.CITATION:Caldwell, S, Williams, K, Guo, J and Chen, W, 2017 Aeration induced moisture reduction of iron ore, in Proceedings Iron Ore 2017, pp 455–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic-Upper Permian sequence, and has enabled the upper part of the lllawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in the survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the upper part of the llawarra Coal Measures, as revealed by the seismic reflection survey.A synclinal axis striking at approximately 55° has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by combined analysis of seismic and magnetic results.

Jan 1, 1970

By Jerry Gagnon, Matt Burr, Dave Evans, Timothy Ellis, Davies Kakengela, Abbas Mirza, Larry Webb, François Leclercq, Andrew Johnston

Lead-based alloys are the primary anodes used in electrowinning from sulphate-based aqueous systems. Lead anode technology has evolved over the years, migrating from pure lead and lead-antimonial alloys to the present day lead-calcium-tin alloys for copper electrowinning and lead-silver alloys for zinc electrowinning. It has also migrated from cast to rolled microstructures in search of improved mechanical properties and higher corrosion resistance. Although great strides have been made in the development of new alloys and production processes, the industry still has unresolved issues related to untimely corrosion which limits anode life and may lead to higher contaminant levels in the metal being produced. Lead anodes corrode because of the difference in the chemical/electrochemical potential across the microstructural features of an anode. Given a very high purity material, we find that the grain boundary areas corrode significantly faster than the rest of the grain. The desire to minimize grain boundary corrosion by a balance of alloying element selection and microstructural design allows the grain boundary area to be engineered. However, operational issues can lead to unexpected corrosion behaviours which we will discuss moving forward. The comments in this work, though directed toward copper electrowinning, can be extended to similar phenomena in other metals electrowon from sulphate media (i.e., zinc, nickel, cobalt, manganese). The lifecycle of electrowinning anodes is dependent upon electrowinning tankhouse operating conditions and maintenance of the anodes, including cleaning and straightening. This paper will focus on the operational aspects of maximizing the utilization of lead electrowinning anodes.

Jan 1, 2015

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By Wilbert T. Malenka

A modified factorial experiment was used to determine the effect of operating factors in hydraulic mining of anthracite. Seven basic factors at various levels were considered. The significant factors were found to be pressure-volume, pattern, and jet traverse speed. Mining data were programed for computer, and a prediction equation was determined from printout information based on the hydraulic "jumbo" operating parameters and characteristics of anthracite, The source of error is discussed. The prediction equation is general in nature and might be useful in delineating performance characteristics in the design of equipment and/or more effective utilization in a medium with characteristics similar to those of anthracite.

Jan 1, 1968

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009