Search Documents

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By Colin Barratt

The East Side Access (ESA) project is the largest underground rail infrastructure project under construction in New York City, USA. The Manhattan segment of the project is to be mined through rock and consists of 4.1 miles of Tunnel Boring Machine tunnels for track work and mined excavations to house rail switches, air plenums, and other rail facilities. This paper considers different methods for concrete lining, such as the use of fixed forms, adjustable forms, and pneumatically applied shotcrete. The advantages and disadvantages of these methods are discussed and the basis for considering one over the other are illustrated. Further discussions on design development and preparation of documents to facilitate quality and constructability in the field are presented.

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Natalia Konstantinova, Georgy Novikov, Pavel Rekant, Goergy Cherkashov, Olga Bogdanova

The economic interest of oceanic ferromanganese crusts and nodules is determined by high grades of major, rare and earth rare elements in these types of marine minerals [1]. Modern oceanic ferromanganese deposits have a global distribution with the largest fields in the Pacific Ocean. The Arctic Ocean still remains a poorly explored region. The first ferromanganese deposits from the deep part of the Arctic Ocean were recovered almost at the same time in 2012 both in US and Russian cruises to the Chukchi Borderland (1) and Mendeleev Ridge (2). Preliminary results of mineral deposits from the first area were reported at UMI-2012 by James Hein et al. [2]. We present here the data of ferromanganese deposits from the Mendeleev Ridge.

Sep 1, 2014

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By Eggleton R. A

X-ray diffraction techniques are commonly used in the identification and quantification of fine-grained materials. A relationship exists between the size of crystals in a sample and the degree to which they diffract X-rays. The Scherrer equation relates the broadness of diffraction peaks to the size of crystals responsible for diffraction (Klug and Alexander, 1974). Relatively large crystals of the order of I - 10 ¦m strongly diffract X-rays; the diffractogram of such crystals exhibit narrow intense peaks. As the size of the crystals in a sample is reduced, diffraction peaks become broader and less intense. Crystals less than 10 nm generally exhibit broad, diffuse and low intensity peaks. Some material is so fine-grained and poorly-diffracting that X-ray patterns show very little information in a normal one-hour scan thereby necessitating very long acquisition times of up to 12 hours. The term poorly-diffracting material (PDM) was coined for such material found within the bauxite deposit of Weipa, northern Queensland (Tilley and Eggleton, 1994; 1996). Common regolith minerals such as hematite, goethite and layer silicate clays are quite commonly fine enough to possess a poorly-diffracting character. Noncrystalline and poorly crystalline Fe-Si-Al-oxyhydroxides such as allophane, opal, ferrihydrite and hisingerite, have either a nondiffracting (amorphous) or poorly-diffracting nature (Eggleton, 1987).

Jan 1, 1997

Permian coal seams from the Tomago Coal Measures in the Northern Coalfield, New South Wales, were analysed petrographically and reflectance measurements made for each. Vitrite contents were moderate to high for most of the coals but for two they were very low.The mineral-matter contents were low to moderate by Australian standards. Different profiles of a particular seam could be correlated by petrographic methods.Standard seam profiles were drawn up and from these an idealized Tomago seam sequence was compiled. All the coals were of high-volatile bituminous rank. Their carbon contents, but not thcir reflectances, varied significantly with the quantity of vitrinite present.

Jan 1, 1968

By Henry Stoch

It?s a green, green world ? Public concern about the impact of human activities on the environment and the roles that businesses play in that impact is rising. What?s happened in the last few months? ? Recent news: ? British Columbia announces carbon tax in 2008 budget ? Federal Court ruling stalls oil sands approvals due to a lack of consideration of GHG implications ? US Energy Independence and Security Act could limit government procurement of oil sands-derived fuels ? Western Climate Initiative (WCI) suggests a ?first seller? approach for regulating generators outside WCI jurisdictions ? Implications ? A cost for carbon has arrived ? The lack of a GHG strategy can have a material impact on your business ? Regulations in other jurisdictions could affect your organization

May 1, 2008

By J. P. Van Cruyningen, M. J. Puro

"A 2400 acre extension to the existing Tailings Area is under development at Inco's Copper Cliff Milling operations.The new area is being developed in stages as production levels dictate thus minimizing immediate capital expenditures while permitting disposal operations to proceed as further site work progresses.The first stage of the new storage site will be fully operational by early 1987 and will include a 400 acre site specific to the storage of Pyrrhotite rejected from milling circuits. The Pyrrhotite site is located in the centre of the Tailings area and is designed for water cover throughout much of its projected life.The new development incorporates perimeter dams designed to operate with low phreatic levels for maximum structural stability. Acid seepage water is collected behind secondary impermeable dams for return to the Tailings Pond.Tailings are deposited by up-stream methods permitting segregation of coarse fractions for use in future lifts of the perimeter dams."

Jan 1, 1987

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019

By Robert H. Leach, C. H. Chatfield

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a stand¬ard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By Stephen A. Gasiorowski, Frank J. Hrach, James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity - up to 40 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonne of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle-particle contact. The small gap, high electric field, counter-current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in North America and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Jan 1, 2012

By R. Cao

Geostatistics was initially developed in the mining sector, but has been extended to other geoscience applications, including forestry, environmental science, soil science, and petroleum science and engineering. This paper presents methods, workflows, and pitfalls in using geostatistics for hydrocarbon resource modelling and evaluation. Examples are presented of indicator variogram analysis of categorical variables, lithofacies modelling by sequential indicator simulation and hierarchical workflow, porosity modelling by kriging and stochastic simulation, collocated cokriging for integrating seismic data, and collocated cosimulation for modelling porosity and permeability relationships. These methods together form a systematic approach that can be effectively used for modelling natural resources.

Jan 1, 2014

In 1950, about a third of the world?s population lived in cities. That figure has steadily risen throughout the following decades. Now it is believed that about 60 percent of the estimated 8.1 billion people in 2030 will be living in urban areas. The strain on infrastructure in cities in the developed world is already showing. And the rapid growth in developing nations today is adding to the shortage of materials, equipment and labor needed to keep up with this growth. So, while materials and labor may be in short supply, there is no shortage of work for the underground tunneling and space industry. In June, 718 of those professionals from around the world were in San Francisco, CA for the North American Tunneling (NAT) conference, put on by the Underground Construction Association (UCA) of SME. The attendees spent the three days of technical sessions listening to international authors discuss the state of the industry, new technologies that have become available and updates on major tunneling projects throughout the world. The accompanying exhibit attracted 79 vendors, who displayed the latest in tunneling and underground space equipment and services. In addition to the technical sessions and the exhibit, the NAT featured three short courses ? ?DRB Process Update Workshop,? ?Soft Ground Tunneling Technologies? and ?Underground Blasting Technology and Risk Management.? And the post-meeting field trip to the Devils Slide tunneling project near San Francisco was sold out.

Jan 1, 2008

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

By Belcher C. B

A procedure was required for the rapid determination of silicon in low-alloy irons and a suitable method used the formation and reduction of silicomolybdic acid at 50&#176;C. The procedure gives results for elemental silicon and this enables the correct computation of oxidation requirements in basic oxygen steelmaking. The method could be useful in iron foundries which have not installed direct reading spectrometers.INTRODUCTIONOxygen steelmaking experiments required rapid determinations of 0,5-1,6 per cent silicon in iron (3-4 per cent C) within 10 min of sampling; a reproducibility better than &#177;0.03 per cent Si was desired. Only elemental silicon (Si&#176;) is of interest as a fuel in basic oxygen steelmaking technology, and the proposed procedure determines exclusively this form of silicon. The method is described as it may prove useful to other workers although the interference study would be incomplete for some applications.The analysis of silicon in iron is frequently obtained using direct reading spectrometers, but for the proposed experiments the spectrometers could not be used because of the prohibitive distance from the furnace. It should be noted that spectrometers determine both the elemental silicon and that present as silicon dioxide in occluded slag and inclusions.The silicon content of iron and steel is determined in this laboratory by spectrophotometric measurement of a &quot;molybdenum blue&quot; colour. The reactions involved have been extensively investigated; Strickland (1952) showed that a...

Jan 1, 1965

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.