Search Documents

By Guanghui Li

In the paper, the recovery technology of gallium from zinc-leaching residue by cold-bonded coal-based direct reduction process following magnetic separation was developed. The results show that the scattered metal Ga can be concentrated obviously after the reduction of zinc-leaching residue briquette and magnetic separation of reduced product. At the same time, the volatilization of Zn in the residue is enhanced during the reduction. When the residue, bear¬ing 18.60% Zu.21.18% Fe and 527 g/t Ga, was reduced with coal at 1100°C for 150 min, the results of Zn volatilization of 9842% and Ga recovery of 89. 10% were obtained in reduction. After magnetic separation of the reduced product, the concentration of Ga in sponge iron is 2164 g/t, and the separation recovery of Ga reaches 92.42%. The enriched mechanism of Ga during reduction -separation process was studied by using electron microscope, scanning elec¬tron microscope, energy spectrum and mineralogical analysis. The investigations show that there is no formation of independent phase of Ga during reduction process. The Ga occurs mainly in metallic iron phase (the concentration of Ga in metallic iron phase is 0.04%-0,4%), in addition, there exists a little Ga in poorly crystalline sulphide (o.08%-0./5Y& Ow). But Go does not exist in most of glass and silicate phase. The affinity of Ga for metallic iron is the enrichment basis of Go in reduction, and it is also in favor of recovering Go during magnetic separation. Key Words: Gallium Zinc-leaching Residue Cold- Bonded Direct Reduction

Jan 1, 2003

By W. G. Davenport

Changes in copper extraction from 1960 till today are documented. The top ten changes have been: (a) replacement of reverberatory smelting by high intensity oxygen rich smelting (b) growth of the Outokumpu flash smelting to over 50% of the world's smelting capacity (c) successful development of single furnace coppermaking but only for low slag fall concentrates (d) replacement of the batch Peirce-Smith converter by continuous converting, but only in a few cases (e) increased SO2 capture throughout the industry, mainly-as sulfuric acid (f) development of low initiation temperature `big bight' Cs catalysts for treating the continuous high-SO2 strength gases from continuous smelting/converting (g) complete replacement of reverberatory anode scrap and cathode melting furnaces by the Asarco shaft furnace (h) adoption of stainless steel permanent cathodes and automated stripping technology for electrorefining and electrowinning (i) complete elimination of wire bar casting by continuous bar casting/rod rolling (j) development and adoption of extractants for turning weak impure leach solutions into strong pure electrolytes. It is postulated that the biggest possible change over the next 20 years would be complete replacement of smelting/converting by hydrometallurgical processing. However, this seems unlikely due to copper purity, precious metal recovery, and economic concerns. The increasing value of sulfuric acid to many copper companies gives chalcopyrite smelting/oxide-supergene leaching a nice synergy especially with the energy credits now coming from continuous smelters, and their acid plants.

Jan 1, 1999

La influencia de los estudios de adsorción para el beneficio de los minerales, se relaciona con la flotabilidad de las especies minerales, y la perspectiva que se ofrece para el progreso de la metalurgia de concentración. Por ello, el objeto de la investigación se basa en la realización de tales experimentos como búsqueda del dominio de la clase de fenómenos fisico-químicos. Dentro de los métodos usuales de determinación de xantatos por yodo, se buscó hallar la concentración por medio del descenso de la adsorción, para determinar la máxima cantidad de reactivo y encontrar el más adecuado para el mineral. Empero, se reparó que a mayor concentración de colector, se genera mayor adsorción. Asímismo cuando se añade el xantato sobre el mineral con poca agua, la cantidad de reactivo adsorbida es superior, justificándose la ventaja que en procesos industriales significaría acondicionar después del espesamiento. En cuanto a la adsorción de galena oxidada, se observa que mezclando este mineral con un sulfuro de zinc, disminuye la adsorción. Posteriormente se ve cómo la superficie oxidada de la galena, puede alterarse por medio de reactivos, variando el grado de adsorción para los diferentes reactivos colectores de flotación. Finalmente se infiere que la realización de las pruebas pretenden determinar principalmente cuál es el reactivo más adecuado más adecuado para una galena determinada.

Jul 20, 1957

The western Cordillera of North America, including more than 99% of Alaska, is made up of an agglomeration of litho-tectonic terranes, some of which have undergone large rotations and (or) translations. The larger terranes can be broadly grouped into a small number of composite terranes based on affinities in their lithology, structure, and tectonic evolution. The terranes reflect repeated episodes of marginal rifting as well as formation of marginal arcs, island arc chains, back-arc basins, and oceanic plateaus since late Proterozoic time. Accretion to the continental margin occurred mainly from Middle Triassic through Early Cretaceous time. Major northward dispersal of terranes was largely during the existence of the Kula plate from about 85-55 Ma. Major rotations are the mid-Cretaceous opening of the Arctic Ocean basin with counterclockwise rotation of Arctic Alaska and Laramide oroclinal bending of western Alaska. The present complex Cordilleran geology along the northeast Pacific rim is a sum of these earlier accretionary processes together with continued Cenozoic faulting and deformation that has been superimposed upon the agglomerated displaced terranes over a broad segment of the continental margin.

Jan 1, 1990

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925

By E. J. Harris

Data obtained from mine ventilation pressure and quantity surveys are required to accurately diagnose ventilation problems, project future air quantity needs, and to locate conditions adversely affecting the efficiency of a mine ventilation system. A method for making mine ventilation pressure surveys with aneroid altimeters was presented in Bureau of Mines Information Circular 7809, and a description of field calculation technique is presented. This report supplements Information Circular 7809 by developing the information obtained during a mine ventilation pressure survey into a single equation suitable, with appropriate modification, for use with desk-top calculators and digital computers. The equation can be used to calculate the ventilation pres sure from the base station to any underground station, or between any two underground stations, and can be programed for semiautomatic sequential calculation using a desk-top calculator. An example of application to a programed desk-top calculator is provided in the appendix.

Jan 1, 1973

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By Stig Petersson

Slag from the converting of copper matte is usually recirculated to the smelting furnace. This recirculation generally causes disadvantages as magnetite-build-up in the furnace, accumalation of impurities as antimony, lead, nickel etc in the process. The treatment of converter slag in a separate furnace in order to recover the copper and nickel content would be of advantage from several points of view. At the Mining and Metals Division, Boliden, testwork has been carried out to treat converter slag from the PS-converters in a separate furnace. The tests have been performed in laboratory and pilot plant scale. The pilot plant tests have been carried out in a TBRC with charges of 5 tons. Based on these tests a full scale TBRC has been projected in order to treat the slag from the PS-converters. This slag will be reduced with copper concentrates to give a matte and a final slag low in copper and nickel. The background and data from the testwork are presented. Also the lay out, technical data and flowsheets for the projected process are shown as well as some production data from the Rönnskär smelter.

Jan 1, 1976

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By R. Hogg, J. M. Mutmansky, E. Kaya

"Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research.The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, nonrespirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.INTRODUCTIONRecently, a considerable amount of research effort has been directed toward better understanding of the characteristics of the coal dust generated during the mining process. It is generally believed that dust characteristics play a significant role in the development of Coal Workers' Pneumoconiosis (CWP). In order to effectively protect coal workers from coal dust, it is important to understand the properties of dust, the mechanisms of generation and dust-lung reaction. Conducting research on dust characterization, dust control and the biomedical aspects of dust toxicology generally requires a large sample of airborne coal dust. Unfortunately, current dust sampling instruments are not able to meet this demand because only a few milligrams of dust are collected."

Nov 1, 1995

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By W. D. Sinclair, R. J. Cathro, E. M. Jensen

"The Cash is one of the largest porphyry copper-molybdenum Deposits found in Yukon to date. It is 80 km northwest of Carmacks, within the unglaciated portion of the Dawson Range, and is associated with the Big Creek fault, an important tectonic feature. Part of the mineralized zone is blanketed by up to 70 m of alluvial drift . The remainder is covered by a relatively thin residual soil layer. The mineralized zone, however, was not detected by conventional stream-sediment sampling because pathfinder elements, such as Cu and Mo, have not been geochemically dispersed into the main drainage system. The deposit was discovered by a combination of soil analysis and inspection of rock fragments from small pits.Twenty widely spaced, shallow drill holes have outlined an areaover 2700 m long and 550 to over 1000m wide that grades more than 0.1% copper equivalent (% CuE = % Cu + (5 x % MoS2)). Two smaller zones grading over 0.4% copper equivalent occur within the larger area. The limits of the widest end of the deposit have not been delineated.The Cash deposit is fairly typical of high-level, calc-alkaline porphyry copper-molydenum occurrrences in the Canadian Cordillera {cf, CIM Special Volume 15) and is representative of most prospects in the Dawson Range. It is associated genetically with a subvolcanic complex of small, irregular stocks and dykes of feldspar porphyry and related breccias of Late Cretaceous age. Copper and molybdenum sulphides occur along fractures, in quartz veinlets and disseminated in feldspar porphyry and in older metasedimentary and intrusive rocks. Higher-grade zones of copper and molybdenum have associated potassic alteration. Phyllic alteration is, in part, superimposed on potassic alteration. Argillic alteration occurs locally.This paper describes the history of the discovery and the geochemical and geophysical characteristics, together .with the regional geology, and the nature and distribution of the host rocks, hypogene mineralization and hydrothermal alteration."

Jan 1, 1981

By V. E. Dementyev

This paper presents a brief overview of some IRGIREDMET advances in gold hydrometallurgy. Original impulse-percolation technology and equipment for intensive cyanidation of gravity concentrates have been developed and introduced into industrial practice by IRGIREDMET since 1980s (RF Patents N1593250). The process is based on leaching using special hydrodynamic and reagent conditions providing high dissolution rate for coarse gold particles. Gold and silver are precipitated from pregnant solution by cementation or electrowinning. There was also proposed an im-proved cementation method using zinc in a contact with electrically conductive material. The units including closed water recirculation, tails detoxification and semi-dry tails IRGIREDMET is well experienced in gold adsorption technology using ion exchange resins and activated carbons. The comparison of CIL and RIL processes were done for a number of gold mines, for example for Sukhoi Log gold deposit. The properties of prospective foreign and domestic ad-sorbents including strong-base, bi-functional and weak-base resins as well as activated carbons were studied. The Institute has developed some adsorption/elution technologies and equipment, such as a two stage RIP adsorption technology for gold/silver ores, an improved technology for gold elution from loaded resin and carbon, electrowinning cells for gold recovery from RIP and CIP eluates etc. Large scale ?Resin In Pulp? tests using weak-base resin were finalized and process design criteria were developed. Gold plant design is on progress at the moment. Improved technology for carbonaceous (preg-robbing) gold ores was developed. It was tested for some gold deposits including Sukhoi Log. It allows to overcome preg-robbing activities of ores treated and to improve dramatically performance of cyanidation and adsorption circuits. The studies on refractory gold ore treatment including bio-oxidation, pressure oxidation, roasting and ultra-fine grinding were conducted. Heap leach technology was tested and introduced by Irgiredmet for a number of Russian mines. Zinc cementation, activated carbon and ion-exchange resin adsorption were used for gold recovery from pregnant heap leach solutions. The options including combined technology ?Heap leach/ RIL or CIP? for clay ores were also developed and tested. The plant using developed technology is at construction stage now. The study on In-Situ gold leaching was conducted. The comparison of different gold lixiviants for this purpose was carried out. Gold recovery from pregnant leach solution by activated carbon and anionite including gold elution from loaded adsorbents etc. was also studied. In 2000 the In-Situ leaching technology was commissioned at Maminskoye gold deposit (Ural). The technologies for treatment of complex ores and by-products were proposed. For example, the technology of gold, silver, copper and zinc recovery from calcines after sulphuric acid production was developed.

Jan 1, 2014

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that's what we're in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today's competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn't much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don't become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that's precisely what we, at Amax: Gold, have done!

Jan 1, 1992

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By O. P. Arora, M. Metzger

Single-phase aluminum containing 1 to 600ppm copper was studied in 7 to 26 pct HCl. The corrosion rate in the autocatalytic stage was resolved into a constant intrinsic component and an acdelerating autocatalytic component, and attention was focused on the part of this stage where the corrosion rate could be described by a simple empirical relation. Autocatalytic corrosion in this period was localized and its rate increased rapidly with copper content and with the strength and chlaride content of the acid. The effects of adding cupric ion to 16 pct HCI were functionally and quantitatively inconsistent with the autocatalytic rates observed. A theory of these rates was given based on the deposition in nzetallic contact with the aluminum of part of the copper introduced by corrosion. It has long been known in a general way that aluminum containing sufficient copper suffers in hydrochloric acid an autocatalytic acceleration of corrosion resulting from the introduction into the acid of copper ions and their reduction on the specimen as elemental copper, which provides cathodes of low hydrogen overvoltage.'-3 In a previous paper, this phenomenon was identified in single-phase high-purity material at copper levels as low as 20 ppm and an empirical equation describing autocatalytic corrosion rates in 16 and 20 pct HC1 was presented. In the present work the range of acid strength and chemistry studied was extended, a more accurate empirical equation for the autocatalytic rate was determined, and a theory of this rate was formulated. A major source of interest in this system is the intergranular corrosion, which is also strongly influenced by copper content,= and an objective of the present work on general corrosion was to provide a basis for studying the role of copper content in intergranular corrosion, which is experimentally much less accessible.

Jan 1, 1963

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959